SPECIAL REPAIR TO OFFICER MESS GENTS TOILET IN BUILDING NO P 92 AT ASC CENTRE (SOUTH) 2 ATC AND PROVISION OF WATER SUPPLY LINE WITH ALLIED WORKS TO BUILDING NO P 37 AND P 33 OF ASC CENTRE (NORTH) UNDER GE (CENTRAL) BANGALORE

Amount

B/R PORTION : M & L for surface excavation averaging 15cm deep and n.exc 30cm deep and getting out as in soft/loose soil including removing the soil to a distance exc 250M but not exc 500 M and depositing where directed complete all as specified and directed.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation, UG cable, water supply pipe line manhole etc area not exceeding 10 Sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Excavating in post holes (or similar holes) in soft/loose soil each n. exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc 25cm, watering and removing surplus soil to a distance n. exc 50m and making good surface as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated material to a distance exc 50m but not exc 250 metre and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

M & L for moorum/sand/red bajri filling under floors or in foundations laid in layers n exc 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.

Provision of trenchless bore using mechanical nuematic drilling equipment for passing electric cables through HDPE pipe of 100mm dia under the existing bituminous/WBM road/PCC hard standings, depth range not less than 1.0 mtr and upto 1.5mtr and making good to the distrubed surfaces of road to match with its existing specifications all as specified and directed by engr-in-charge at site. Note : 1. Quoted rates deems to be inclusing of necessary earth work, transportation charges of Drilling machine, and cost of HDPE pipe and passing pipe through bore complete. 2. Any damage to MES assets caused during trenchless bore shall be recitfied by the contractor at his own cost.

M & L for Hardcore of broken/crushed stone aggregate of gauge n.exc 63 mm deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Providing cement concrete type B-1, 1:2:4 mix (using 20 graded stone aggregate) as in coping, benching, roof kerb, filling gap between roof sheet and wall and the like including necessary formwork.

Demolition of plain cement concrete (unreinforced) in ground floors, plinth protection/path/pavings etc not exceeding 15 cm thickness. (below or above ground level) and removing debris outside MD land complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc and removing debris outside MD land complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water and removing debris outside MD landcomplete all as specified and directed

Demolition and breaking of 100mm to 150mm bore salt glazed stoneware drain pipes including PCC benching/ PCC complete all as directed.

Taking down chowkats or frame, not exceeding 1.5 Sqm in each with shutters (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frames, exceeding 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposing serviceable tiles to MES store and the rubbish/debrises out side MD land complete all as specified and directed.

Taking up or down 20mm bore, Steel tubing and connections.

Taking up or down 25mm bore, Steel tubing and connections.

M & L for granite stone slab, table rubbed and polished (of any type) 18 to 20mm thick, machine cut, as in flooring, window cill and the like bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 15 mm thick screed bed in cement mortar 1:4 & cutting, polishing complete all as specified and directed.

M & L for granite stone slab, table rubbed and polished (of any type) 18 to 20mm thick, machine cut, as in skirting/dado, steps, jambs, pillars and the like bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 15 mm thick screed bed in cement mortar 1:4 & cutting, polishing complete all as specified and directed.

M & L for roundings to edges of stone slabs, one edge, such as in steps, cooking platform and other similar situation complete all as directed.

M & L for 25 mm thick, plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in base of flooring, level course etc and finished the surface fair to receive top layer screed bed complete all as specified and directed.

M & L for Plain cement concrete 1:5:10, type E-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, complete all as specified and directed.

M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, level course, sub base for hard standing etc complete all as specified and directed.

M & L for Plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for precast cement concrete block masonry type C1, 1:3:6 (20 mm graded granite stone aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M & L for precast cement concrete solid building blocks or slabs as in masonry, 10cm thick, type C1, 1:3:6 (20mm graded aggregate) set in cement mortar 1:4 complete all as specified and directed.

Providing cement concrete type C-1, 1:3:6 mix (using 20 graded stone aggregate) roof kerb, filling gap between roof sheet and wall and the like including necessary formwork.

M & L for non-skid, ceramic, joint free of matt finish, coloured tiles 8 to 10 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm, in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for glazed ceramic, coloured tiles, 300X600mm, 7 to 8mm thick as in vertical surface of walls, skirting/dado/steps including 10 mm thick screed bed in cement mortar 1:3 set & jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles complete all as specified and directed.

S & F solid PVC door frames of size 50mm x 47mm made out of 5mm single side prelam & edges will be painted to match with prelam PVC sheet reinforced with MS square tube complete all as specified and directed.

S & F factory made PVC moulded door shutter 30 mm thick (style) with wood free EPS, with 2, 4 or 6 raised panel design with 2 mm thick 3D wood grain moulded prelam PVC sheet polyurethane painted on the front face & 2 mm thick prelam plain colour PVC sheet on back face all as per specification and drawing shown in SSR Part II complete and as directed.

S & F 125 mm long, brass, barrel tower bolts with cast or sheet barrel and roller or cast bolts and fixed complete all as specified and directed.

S & F 125 mm extruded brass handles, fabricated type polished complete all as specified and directed.

S & F in repair 40mm dia brass cupboard knob, bright finished, brass polished fixed with nut, screw and washer complete of approved make and design as directed by Eng-in-charge.

Supply and fixing factory made UPVC any colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(Area of door upto 2.00 sqm) comprising of UPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws,etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in-Charge. (Glass shall be paid separately) Note: For UPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S & F factory made UPVC white colour sliding window three track made of extruded profile with wall thickness of 2.3mm (+-0.2mm) window profile with hollow section with multi chamber. Frame (88mmx52mm), sliding sash (42mmx67mm). Sliding mesh sash (42mmx57mm) Sliding interlock (one vertical length in each shutter)(45.5mmx28mm) glazing beads (24.5mmx 16mm) will be mitred cut and fusion welded at all corners incl drilling of holes for fixing hardware and drainage of water etc making arrangements for fixing of hardware EPDM gasket 1.2+-0.2mm thick galvanised steel frame (30mmx 18mm) 2 Nos, sliding mesh sash (26mmx10mm) profile to be inserted in required profile frame will be fixed to the wall with 8mmx100mm long fasteners Hardware (touch lock of zinc alloyed (white powder coated) steel roller system including providing stainless steel wire cloth 0.24mm nominal dia of wire and average width of aperature 1.40mm and required accessories area n.exc 2 sqm each. ( Note :- (i) Cost element for all connected accessories except glass pane shall deemed to be included in quoted rate. (ii) Glass pane shall be measured and paid under separate item as supply only. (iii) Net opening will be measured for payment purpose)

Supply and fixing factory made UPVC any colour Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension (Area of window upto 0.75 sqm.) comprising of uPVC multichambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), UPVC extruded glazing beads of appropriate dimension,EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass shall be paid separately) Note: For UPVC frame, sash and mullion extrudedprofiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made complete all as specified and as directed. depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. ®

Supply only 6.00 mm thick, sheet glass, ordinary quality and glazing with upvc beading in square exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S & F solar control film 25 micron reflective type sticked to glass panes as per manufacturer's instruction complete all as directed.

Supply and fixing 12 mm thick, toughened glass, exc 0.5 sqm in each pane as in partitions and the similar work including cutting to shape, grinding, roundings and drilling holes etc complete all as specified and as directed.

S & F 18/19mm thick block board grade 2 quality, interior grade commercial type, fixed with screws to timber frame work complete all as specified and as directed.ete all as directed.

M/L for 0.90 mm thick decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacture's instruction complete all as specified and as directed.

S & F continuous (Piano) hinges, mild steel bright finished or electro galvanised, width of flaps 40mm when open complete all as directed.

S & F second class hard wood, clean sawn timber fillets, square or rectangular, exc 3 sq.cm but not exc 6 sq.cm in section, secured/fixed with nails etc complete all as specified and directed.

S & F second class hard wood, clean sawn timber fillets, square or rectangular, exc 13 sq.cm but not exc 25 sq.cm in section, secured/fixed with nails etc complete all as specified and directed.

S & F in repair ball catcher with 8 mm dia steel ball and brass body and striking plate including letting in complete all as directed.

GI frame work for false ceiling seamless comprising of galvanised iron perimeter channel 0.55mm thick with two unequal flangeds of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre / intermadiate channel 0.90mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre using 4mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40X3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long including providing 10/12mm thick plaster of paris ceiling (Gypsum anhydrous) board reinforced with GI wire mesh fixed to the ceiling providing timber fillets fixed with 25mm long self drilling and tapping screws having philips head with under head cutter at 200mm centre to centre, including finishing the joints of face board with specially formulated jointing compound and 48mm wide fibre tape to provide seamless finish complete all as specified and directed. Make of frame work and gypsum board:- Eternit Everest / lafarge/ Armstrong/Saint Gobain as approved by GE

M & L for preparing newly plastered surfaces of ceilings, etc and applying two coats of distemper oil emulsion over a coat of primer including 2mm thick wall care putty complete all as specified and directed.

S & F 4 mm thick, sheet glass, figured/ pin headed glass and glazing with oil putty/timber beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F for stainless steel wire cloth 0.24mm nominal dia of wire and average width of aperture 1.20mm and fixed with stainless steel wire staples, complete all as specified and directed

S & F 75 mm size, butt hinges, medium weight, cold rolled complete all as specified, and directed.

S & F 150 mm long, Aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and directed.

S & F 125 mm size, Aluminium handles, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S & F compound girders and sanchions, lattice girders, areial masts, stagging for water tanks and the like including caps, bases, splices etc built up from two or more beams or channels or angles with plates, including all lattice bars stiffeners, gusset plates. Steel section shall conform to Fe-410-W (Gde- E- 250) weldable quqality - A complete all as directed.

S & F Rolled mild steel work as in trusses,purlins, posts etc using Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc including cutting, welding complete. Steel section conforming to Fe-410-W (Gde-E-250) weldable quality-B complete all as specified and directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick (Total coated thickness) of any colour, finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with best quality self tapping screws as specified

S & F Pre-Painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/valley gutter, fixed with self tapping screws complete all as specified and directed. (Colour of ridge shall be same colour as that of sheet used for roof)

S&F in repair 110 mm dia PVC (SWR) pipes, Type 'B', single socketed,in any length with rubber ring joints,laid in trenches or in floors complete all as specified and directed.

S&F in repair 75 mm dia PVC (SWR) pipes, Type 'B', single socketed,in any length with rubber ring joints,laid in trenches or in floors complete all as specified and directed.

S & F 110 mm bore, PVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with solvent cement joints fixed to wall using MS holder bat, etc complete all as specified and directed.

S & F 75 mm bore, PVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with solvent cement joints fixed to wall, using MS holder bat etc complete all as specified and directed.

S & F 110 mm bore, PVC (SWR) bends of any radius with acess door complete all as specified and directed.

S & F 75 mm bore, PVC (SWR) bends of any radius with acess door complete all as specified and directed.

S&F PVC (SWR) junction single,(single T) 110 mm with access door complete all as specified and directed.

S&F PVC (SWR) junction single,(single T) 75 mm with access door complete all as specified and directed.

S & F 75 mm dia outlet , PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S & F in repair 75 mm dia outlet , PVC (SWR) multi floor trap, with grating including jointing to waste pipe with solvent cement, fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S & F in repair PVC (SWR) gully trap 125/110 mm, with grating including jointing to waste pipe with solvent cement, fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar 1:4 on stone masonry wall surfaces or other than fair faces of brick work and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar 1:6 on other than fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for preparing newly plastered surfaces of internal walls, etc and applying two coats of distemper oil emulsion over a coat of primer including 2mm thick wall care putty complete all as specified and directed.

M & L for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and directed.

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

M&L for cutting holes superficial area exc 150 Sqcm but n.exc 400 Sqcm into or through stone walls built in cement mortar complete all as specified and as directed.

Supplying and laying of 20mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of 25mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S & F 20mm CPVC ball valve brass insert complete all as directed.

S & F 25mm CPVC ball valve brass insert complete all as directed.

S & F PVC connection pipe with PTMT nuts, 450 mm long. Make: CERA/Hindware/Parryware/PRAYAG

S&F stainless steel towel rail 600mm long brass body . Make.CERA .cat no. F5002103 or equvalent of Make Hindware/Parryware/ PRAYAG

S&F stainless steel toilet papper holder with flap guard . Make.CERA .cat no. F5002110 or equvalent of Make Hindware/Parryware/PRAYAG

S&F towel ring of CP fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed.(Make:Cera F5002105 or equvalent of Make Hindware/Parryware/PRAYAG)

S&F for multi purpose wall Mounted sensor soap/ shampoo / hand wash/sanitizer dispenser glass finish complete all as specified and as directed.(Make:Prayag BSS-15 or equvalent of Make Hindware/Parryware/CERA)

S&F for Sensor hand dryer BSD-18 Touch free infrared activation, wall mounted type, sensor range 12-15cm.(Make:Prayag Cat No.BSD-18 or equvalent of Make Hindware/Parryware/CERA)

S&F Stainless steel curtain bracket suitable for 25 mm dia curtain rod including steel rings and wooden support complete all as specified and directed.

S&F 25 mm dia stainless steel curtain rod complete all as specified and as directed.

S & F 32 mm bore of dicharge pipe bottle trap of PTMT having mimimum water seal of 25mm (minimum weigh 260 gms) complete all as specified and as directed.

S & F in repair deck mounted sensor pillar tap 15 mm dia with control box set , fancy type, cast copper alloy with capstan head screwed down high pressure, screwed for iron pipe and fixed. Make CERA cat No F6010102 or equivalent of Parryware/Hindware/ Prayag

S&F in repair 15 mm bore bib taps long nose with wall flange and aretor, cast copper alloy, fancy type, chromium plated with capstan head screwed down to iron pipe complete all as specified and directed. Make: CERA Cat NO F1007152 or equvalent of Make Hindware/Parryware/PRAYAG

S&F in repair 15 mm bore stop valves/angle valve with wall flange, cast copper alloy chromium plated fancy type with long shank and cup, concealed type, screwed down to iron pipe complete all as specified and directed. Make: CERA Cat NO F1012201 or equivalent of Make Hindware/Parryware/ PRAYAG

S&F Vitreous China Wash hand basin , table top/wall hung type, snow white, approximate size 640X450X200 mm including a pair of mild steel angle iron brackets duly painted, erected/embeded in wall, 32 mm waste coupling brass chromium plated suitable for wash hand basins & 32 mm dia LDPE PVC waste pipe, 45 cm long PVC connections including cutting hole and pinning in ends making good disturbed portion using cement mortar 1:3 complete all as specified & directed by Engineer-in-charge. Make of basin CERA Cat No S2020132 or equivelent of Parryware/Hindware/Prayag

S & F in repairs, 550X365X355mm approximate size, vitreous China snow white wall hung type EWC with 'S' or 'P' type trap and white soft close PVC seat cover, including connection to outgoing drain and 32mm dia flush pipe, using new GI flush bend (floor portion) and making good to floor to matching with existing surfaces complete all as specified and directed. Make CERA cat No S1043113 (CROMA) or equivalent of Hindware/Parryware/Prayag

S & F Vitreous China urinal with integrated EFS type size 360X330X740mm (Appx size), white with grating and union for discharge pipe (back or corner wall type) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, providing grating and union for discharge pipe and 32mm dia PVC waste pipe complete complete as specified and directed. (Make: CERA Cat No S4010101(CALCIA EFS) or equivalent of Parryware /Hindware/PRAYAG)

S & F in repair concealed type flushing cistern set with full frame of size 550X95X500mm including aquator knob shine finish to make the system fully functional and making necessary connection as directed. Make CERA cat No B1110108 for cistern/ B1120118 for aquator knob or equivalent of Parryware /Hindware/PRAYAG)

S & F health faucet brass body including wall hook, cast copper alloy & 1 metre long flexible stainless steel braided connection pipe suitable for 15mm bore pipe complete all as specified and directed. Make CERA Cat No F 8030301 or equivalent of Make : Hindware/Parryware/Prayag

E/M PORTION : - (EARTH WORKS AND CONCRETE WORKS IF ANY RELATED TO E/M WORKS SHALL BE MEASURED AND PAID UNDER RESPECTIVE ITEM CATERED IN B/R PORTION) : Taking down surface type copper/ aluminium point wiring (light, fan, socket or power) complete, including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions seperately) and making good distrubed surfaces of wall, floors, etc complete.

Point wiring with PVC insulated and unsheathed FRLS cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including PVC rigid non metalic conduit concealed in stone/concrete wall/roof including (Chase cutting by using electric driven cutter machine) replacement/provision of new metal flush boxes in stone wall fixed flush with wall surface with 3mm thick laminated sheet top cover white plate with frame fixed with brass screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core (FRLS) PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for :- One light or fan point controlled by one 5 Amps switch one way

All same as item No 100 above but one 3 pin socket point 5 Amp on independent board.

All same as item No 100 above but one 3 pin socket point 5 Amp on same board with other switches.

All as per item No. 100 above but with 4.0 sqmm ( Nominal area ) cable with 4.0 Sqmm size copper earth continuity conductor for 3 pin 15 A socket outlet on independent board complete all as specified and directed. Note for item No 100 to 103 : - Cost element for cutting chases into wall and making good using Cement Moratr in 1:4 shall deemed to included in qouted rate.

Supply and fix modular switch 1 way 6/10A,1 module. Make : Legrand/Standard/Cabtree

Supply and fix modular switch 1 way 16A,1 module. Make : Legrand/Standard/Cabtree

Supply and fix modular type sokcet combination flush type 5 /10 Amp 2/3 pin muliti purpose, 2 module. Make : Legrand/Standard/Cabtree

Supply and fix modular type sokcet combination flush type 16 Amp 2/3 pin muliti purpose, 2 module. Make : Legrand/Standard/Cabtree

Supply and fix Ceiling rose surface bakelite 65x50mm three terminals including supply and fix PVC blocks. Make : Anchor/Cabtree/Legrand/Standard

S&F in replacement Pride plus inverter batten of make Havells, LED tube light fitting of 20 watts 6500K , 230 volt, with polycarbonate channel , lithium Ion battery with charging time 8-10 hours and back up time 4 hours complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Havells Cat No LHEXACP7FN1W020 OR equivalent of make Shakti/Crompton Greaves/Bajaj

Supply and fix in repair 42 watt LED Light 2' x 2' LED luminare new generation energy saving environmental friendly long life aesthetically designed, ultra modern recessed mounting with high brightness SMD LEDs as light source, complete with accessories suitable for armstrong/Grid ceiling with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size. Make : Havells cat No PLUTONEO2X2PLR42WLED857S or equivalent of Crompton Greaves / Bajaj/ Philips/Wipro

Supply and fix in replacement Sheet metal enclosure (ISI marked) distribution board for 240 volts, SPN 8 way horizontal type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

Supply and fix MCB single pole 6 to 32 Amps 240 volts, C series, 10 kA rupturing capacity

Supply and fix MCB single pole and neutral, 6 to 32 Amps 240 volts, C series, 10 kA rupturing capacity

Supply and fix in replacement surface type Sub main wiring with 2 runs of 4.0 sqmm, single core, PVC insulated & unsheathed cable FRLS) conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in new non metallic PVC grey conduit (medium grade) with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 4 sqmm single core PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and type of conduit complete all as specified and directed. NOTE:- Two run of wiring cable, one run of earth wire and one run of PVC conduit shall be measured as one unit RM

Supply and Fixing exhaust fan, 300mm sweep plastic body, AC single phase 230/240 Volt including bird free louver shutter cut to fit with hole for exhaust fan including providing holes grouting bolts and 3 core flexible copper conductor cable of size 24/0.20 sqmm connecting up from ceiling rose to exhaust fan terminal complete all as directed. Make : - Usha/almonard/Crompton/Khaitan/Bajaj. NOTE: - Quoted rate deemed to be inclusive of making hole for providing exhaust fan in wall including making good and necessary fixing arrangement of louvre using nut, bolts, washers etc complete.

M&L, for taking down old unserviceable earthi and providing new Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6.0mm thick buried directly in ground (earth pit depth not less than 2.25m deep below the ground level) with top edge of earth plate at a depth not less than 1.5m below ground level connected to earth using GI earth wire of 4mm dia by means of of nuts, bolts and washer and check nuts of GI or steel as shown in electrical plate No.3 of MES SSR-2009 (Part-I) and connected to earth test point all as specified or indicated including testing on completion with and including 15mm bore light grade GI protection pipe 7.5 metre long for earth including PCC (1:2:4) pit with RCC (1:2:4) type B-1 cover, 40mm thick reinforced with 6mm dia MS bars @ 100mm both ways with lifting hooks made out of 6mm dia MS bars, watering arrangement with 20mm dia light grade pipe, funnel, wire mesh, common salt chorcoal, necessary excavation and earth work in any type of soil complete all as specified.

Material and labour for cutting existing 25 to 50 mm bore water supply pipe line in position/without taking down screwing & threading for alterations or additions including providing new union/Tee complete all as directed.

Supply, laying and testing GI water tubing 20 mm bore "medium grade" including all fittings to laid in trenches including necessary cuttings, threading and testing on completion all as specified and directed by Engr-in-Charge.

Supply, laying and testing GI water tubing 25 mm bore "medium grade" including all fittings to laid in trenches including necessary cuttings, threading and testing on completion all as specified and directed by Engr-in-Charge.

Supply, laying and testing GI water tubing 50 mm bore "medium grade" including all fittings to laid in trenches including necessary cuttings, threading and testing on completion all as specified and directed by Engr-in-Charge.

Supply and fix Gun - metal gate valve 20mm bore, vertical/horizontal type with ISI marked and fixed with suitable size of union as directed. Make: KIRLOSKAR/LEADER/ ZOLOTO

Supply and fix Gun - metal gate valve 25mm bore, vertical/horizontal type with ISI marked and fixed with suitable size of union as directed. Make: KIRLOSKAR/LEADER/ ZOLOTO

Supply and fix Gun - metal gate valve 50mm bore, vertical/horizontal type with ISI marked and fixed with suitable size of union as directed. Make: KIRLOSKAR/LEADER/ ZOLOTO

M&L for construction of brick masonary valve chamber of inner dimentions 60 cm X60 cm X 60cm depth with 23 cm thick brick masonary wall in CM 1:6, PCC base in 1:3:6 type C1 using 20mm graded crushed stone aggregate of 7.5cm thick, plastering 15mm thick in CM 1:4 both inner & outer face of brick masonary, 7.5 cm thick PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) copping, angle iron frame 40x40x6 mm size with 3mm thick MS sheet chamber cover single opening arragnment with lock system, all as directed including painting the steel surface with two coats of first quality synthetic enamel paint over a coat of red oxide primer after necessary preparation of surface complete all as specified and as directed by Engr-in-charge at site.

S & F 50 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

S&F double layer rotational moulded polyethylene water storage tanks 2000 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including 50 mm water tank nipple, union suitable for HDPE water tank complete all as specified and directed.

Lucky Enterprises

MAA ENGINEERING SERVICERS