REPAIR TO FENCING, ANGLE IRON POST HARD STANDING FOOTHPATH CHAJJA FENCE REPAIR BARBED WIRE CONCERTINA COIL AND MISC B/R ITEMS AT TECH AREA AT AF STN BKT

Amount

Taking down cement plaster including racking out joints hacking for key scrubbing down with water etc on walls and ceiling complete all as directed.

Demolition of brick work or stone/boulder masonary built in cement mortar of any specification and in any position complete all as specified.

M&L 15mm thick cement plaster on concrete/brick surfaces in CM 1:4 and finished surfaces even & smooth without using extra cement complete all as directed.

M&L for brick work with sub class "B" brick (using old size bricks)straight or curved on plain exc 6m mean radious built in CM 1:4 complete all as specified and directed.

M&L for preparation of new plastered surface of wall and apply two coats cement base paint on new plastered surfaces of wall, white or tinted complete all as directed.

Demolition of cement concrete in ground floor and paving n.exc 15 cm thickness (Below or above GL)

M&L for Forming construction joint 30 mm deep and 10 mm wide filled with sealing compound grade 'A' complete all as directed.

M&L for 100mm thick cement concrete type B-2, 1:2:4 (40 mm graded aggregate) as in floor, sub floos, sub base complete all as specified and directed.

Demolition of RCC of any description and in any position not otherwise specifically provided for

M&L for mild steel 10mm dia and over TMT bars as in reinforcement cut to length bent to shape required including cranking,bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified.

M&L for mild steel 8mm dia TMT bars as in reinforcement cut to length bent to shape required including cranking,bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified.

Ditto all as item no 12 above but 8mm dia as in stirrups and binders.

M&L for RCC 1:2:4 type B-1 (20 mm graded stone aggregate) as in coping, channel of drain and other similar works, all as specified and directed

Dismantling structural steel work including doors, gates but excluding framed truss etc.

M&L framed work as in doors or gates of angle of othger section with gusset plates ,mild steel black sheet,,rails braces etc complete drilled for fixing of steel sheeting or other covering Doors etc to be prepared for hanging or sliding with or including either hooks and hinges or steel hanging door fitings (exclusive of steel sheeting or other covering,running rails and guides) and hanging also fastening and fixing complete

M&L preparetion of old steel surfaces and applying one coat of synthetic enamel paint complete all as specifeid and directed.

S& F in repair collapsible steel gate ,top hung consisting of channels ,pickets,pivoted flatbars,top &bottom runners brass handles etc errected in position & securing with hold fasts & brackets complete all as directed.

Dismantling of posts or structs (wood, steel or RCC) any section, including taking out embeded portion in concrete, brick work, masonary etc and making good distrurbed area complete all as directed.

Excavation in post holes each n exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n exc 25 cm, watering and removing surplus roil to a distance n exc 50 m and making good surfaces soft/loose soil.

Dismentaling of fencing wire mess, chain link of any size and shape any type all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any standards, rails, staining bolts, etc. including provision of binding wire etc complete all as directed.

Supply only chain link MS galvanised fencing any type or size complete all as directed.

M&L mild steel 10mm dia and over TMT bars as in reinforcement cut to length bent to shape required including cranking,bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified.

S&F in repair galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strainging bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or stel pins, etc. as directed (each line wire to be measured).

S&F in repair Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron illets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as directed.

Supply and fix in Helix concertina coil 600 mm dia (in specified stretched position) including "U" clip & "C" clip having 50 number's of spirals & composed of reinforced. punched barbed tape (RPBT) wire having continuous punched blade edged barbes on both sides of coil rolled low carbon steel to centre pitch 36 mm alongwith flattened strip width of 18.60 mm and centre width 7.40 mm. The barbs should have 180 degree straightness with razor edge cut. The razor tape should have minimum galvaniesed coating thickness of 12 microne (both side inclusive). The core wire should have minimum wire dia metre 2.59 mm and tensile strength of 1620N/ Sqmm. All the materials should be coated by dipping process with anti corrosive black bituminious paint conforming to IS-168. The length of coil should be 08 metre stretch per coil. The concertina coil should be as per relivent IS complete all as specified & directed . hot dip galvanized coated with CLR anti corrosive paint by making diamond shape with the help of dove tail clips (18 SWG) fixed over razor wire with the help of hog rings (14 SWG) in angle iron bracket/frame over boundary wall etc complete all as specifed and shown on dranwing/directed. (Note:- Rozer wire and angle iron shall be measured and paid separately).

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in foundation filling & mass concrete all as specified.

M&L for preparation of new steel surface of any description exceeding 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer all as specified.

S&F for aluminium partition using aluminium section 85 x 44.5 x 1.5mm thick (Make:- Hindalco/Jindal) partly panelled and top glazed, bottom panel fitted with 12mm thick prelaminated partical board of standard quality of approved make and top portion fitted with 5mm thick figured glass including necessary aluminium jointing cleat, glazing cleats, rubber packing etc complete all as specified and directed

S&F for Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless stell cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

S&F for 18mm thick Celuka ply of one side prelaminated or digital finished and other side plain white colour to make kitchen cabinet shutter/drawer front shutters complete with incl all fittings as per specifications complete all as specified and directed..

S&F Aluminium door lock vertical type 100 to 150mm size complete with all fittings complete all as specified and directed.

S&F Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as directed.

Supply and fix window glazing of ATC tower at a height of 12 to 14 meters. The glass shall be free from distortion waterproof and with vapor proof seal. The thickness of outer toughened glass (tint as approved by GE/matching with existing window glazing) shall be 5mm thick with 1.52mm PVB lamination with 12mm air gap. The glass shall be heat strengthened (HS) and 5mm thick clean toughened glass (inside) properly sealed. Window glass shall be sealed with silicon sealant all around. The entrapped moist air between the glass pans shall be dehydrated by certified drying agents. The double glass shall withstand the sustained wind speed of 125miles per hour or more. The make of glass shall be SAINT GOBAIN/ MODIGUARD/ SAFEX/ASAHI INDIA. Supply and fixing shall also include the followings:- (a) Loading charges. (b) Transportation charges. (c) Unloading charges. (d) Un-installation of existing defective glass (e) Installation Charges (f) Scaffolding charges for 12 to 14 m height of ATC tower (g) Making necessary framework for packing. (h) Adequate silicon quantity for sealing. (j) Freight charges (k) Insurance against any breakages of glass during transportation/installation and insurance charges for workmen engaged on the work.

S&F in repair 5mm thick toughend glass (Make :- Saint Gobin/Modi Guard/Asahi India) fixed with aluminium frame of any size as directed incl all fitting and fixture.

Dismantling asbestos cement (corrugated semi corrugated, etc.)Sheets in roof coverings

S&F Pre-painted galvatume aluminium zinc coating GI bases corrugatede steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /clading to fixed with self tapping screw as specified .

S&F 1.00 mm thick class 8 plain ,galvanised, mild steel sheeting, in ridge hips, vally gutters, drips and straight flashing (length and grith as fixed) with grade of Zinc coating 275 complete all as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as directed.

M & L for 4mm Non Asbestos fiber Cement building board of size (595x595)mm fixed in powder coated Anodised aluminium frame (snapgrid) of standard section (a) aluminium wall angle 40mmx25mmx2mm, (b) aluminium main tee 36.5x25mmx1.40mm, (c) aluminium cross tee 23.5mm x 26.4mmx 1.40mm, (d) aluminium bracket at cross junction 25mm long (e) mild steel suspenderduly fabricated @ 605mm C/C 4mm dia & 600mm long average with the 4mm thick GI suspender in ceiling and applying on one coat of distemper oil emulsion complete all as directed.

H C CONSTRUCTION

Ainisi Co.