PETTY REPAIRS TO B/R ASSETS IN DRDL,ASL AND ADJOINING AREAS UNDER AGE B/R-I KANCHANBAGH, HYDERABAD

Amount

S&F in repairs 15mm dia stop valves /angle cock / concealed stop cock, fancy type, cast copper alloy, chromium plated screwed down high pressure with crown or capstan head screwed both ends for iron pipe complete all as directed.

S&F in repairs 15mm, 20mm GI fittings( nipples, elbows, reducers, Tee, sockets and tank nipples etc ) complete all as directed.

S&F in repairs waste coupling of 32/38 mm dia of PTMTsuitable for wash basin/ sink half or full threaded complete all as directed.

S&F in repairs chromium plated waste coupling for kitchen sink with combination of ABS plastic and stainless steel comprises of stainer built-in removable strainer will catch any debris or utensils before they clog up your plumbing The strainer also doubles as a drain plug. Simply push down on it to stop water from draining, and pull up to allow water to drain again complete all as directed

Supply and Fix in repair PVC internal fitting of low level flushing cistern with syphon, handle lever etc.

Supply and Fix in repair complete one piece EWC PVC syphon kit for PVC low level flushing cistern with syphon, handle lever etc complete kit. (Make Prayag, commander, Parryware, Supreme

Repairs to leaking bib tap, pillar tap, stop cock, angle cock and gate valve of 15 & 20mm dia by changing rubber washers, or using M seal, etc as required to rectify the defects complete all as directed.

S&F in repairs brass spindle for taps/ stop cock of 15mm dia any type complete all as as directed.

S&F in repairs brass spindle for concealed stop cocks of 15 mm dia, any type complete all as directed.

S&F in repairs 15mm dia bib taps, short body, standard of PTMT, any colour, high pressure, screwed for iron pipe (minimum weight 105gms) complete all as directed.

S&F in repairs 15mm dia bib taps cast copper alloy chromium plated with crown or capstan head, screwed down, high pressure screwed for iron pipe complete all as directed.

S&F in repairs 15mm dia pillar tap fancty type standard of PTMT, any colour, high pressure, screwed for iron pipe (minimum weight 120gms) complete all as directed.

S/F in repairs 15 mm dia pillar tap cast copper alloy with crown or capstan head , chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as directed.

S&F in repairs PVC connections of 15mm size,450mm long with PTMT nuts complete all as directed.

S&F in repairs PVC connections of 15mm size,450mm long with PTMT nuts complete all as directed.

Taking down 15mm dia GI tubing and cleaning and refixing with all fittings and fixtures fixed to walls, ceilings etc complete all as directed.

Taking down 20mm dia GI tubing and cleaning and refixing with all fittings and fixtures fixed to walls, ceilings etc complete all as directed.

Supplying and laying 20mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying 25mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Removal of air lock/ blockage in 15mm/ 20mm bore GI water tubing, cleaning the pipe and fittings etc complete all as directed. Note:-(Work shall be carried out upto G+2 storey bldg, contractor to quote rates accordingly)

S&F in repairs brass chromium plated shower rose with swivel joints 125mm dia with 18mm dia chromium plated pipe complete all as directed.

Repairs to leakage from inlet/ outlet of over head water storage tanks, GI pipe line by using M-seal or tightening of check nut or replacing check nut etc complete all as directed.

Repairs to leakage from CI pipe line joints of 75/110mm dia using cement incuding removal of loose material, dust, scales etc in the leakage portion complete all as directed. Note : Rat including necessary scaffolding and the work shall be carried out up to G+2 storyed building.

S&F in repairs CP framed stainless steel grating 202 grade of size 150x150mm Stainless Steel 304 Square Lock Drain Grating & Frame with or without hole including fixing with white cement complete all as directed.

S&F in repairs plastic water closet seat cover, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging devise complete all as directed.

S&F in repairs gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe, suitable for 20mm bore complete all as directed.

Taking down wash hand basin/ sink vitreous china of any size and re-fixing the same after replacing rusted damaged brackets with 50x50x6mm thick angle arion brackets including cutting for and pinning in ends of brackets complete all as directed.

S&F in repairs brass CP wall mixture three-in-one (3-in-1) system with provision of telephonic shower complete all as directed.

S&F in repairs 75mm dia cast iron nahani / Floor trap with CP grating including jointing to existing pipe in cement mortar, fixed in plain cement concrete 1:2:4 type B1 complete all as directed.

S&F in repairs PVC water tank covers of any size & capacity complete all as directed.

Supply and fix in repairs 20mm dia ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe (Minimum weight 210gms) complete all as directed.

Cleaning and removing all scale and dirt etc from water tanks of capacity exceeding 500 ltrs and not exceeding 1000 ltrs from mouths of circulating pipes etc complete all as directed.

M&L for date of cleaning to be written in synthetic enamel paint on all tank, after cleaning, size of letters shall be 50mm in height and text shall be “TANK CLEANED ON DD/MM/YYY”

S&F in repair brass CP finish (jet spray) Health faucet Hand toilet spray with acessories 1 meter shower tube and stand complete all as directed

S&F in repair brass CP 2 in 1 Bib Cock with wall flange complete all as directed.

S&F in repairs 15mm dia swan neck taps cast copper alloy chromium plated with crown or capstan head, screwed down, high pressure screwed for iron pipe complete all as directed.

S&F in repairs 15mm dia Sink Cock with Regular Swinging Spout (Wall Mounted Model) With Wall Flange screwed down, high pressure screwed for iron pipe complete all as directed. Make : Jaquar(FLR-CHR-5347N)

S&F in repairs 10 ltrs capacity PVC flushing cistern high/low level with inlet, ball valve, float, handle including fitting and fixtures and taking down the old damaged cisterns and providing connections to WC and flush pipe without any damage to the existing fittings complete all as directed.

Taking down existing IWC along with its cement concrete bedding and P or S trap and S&F 'Orissa pattern' vitreous china squatting pan white of size 580x440mm with integral footrest (Excluding flushing cistern and flush pipes) but including concrete bedding and P or S trap as required including PVC flush pipe, making good all the disturbed surfaces to match with the adjoining complete all as directed.

S&F in repairs vitreous china wash basin, white, flat back of size 550 X 400 mm excluding taps, chain and plug and porcelain stopper but including CP waste coupling & brackets and fixed complete all as directed.

S&F in repairs one piece vitreous china white, wash down water closet pan, pedestal pattern including fixing bolts, traps, plastic water closet seat and cover with recessed bottom with MS CP hinging device (excluding flushing cistern and flush pipe) complete all as directed.

S&F in repairs towel rail 450mm long of PTMT fixed with and including chromium plated brass screws (Minimum weight 170gms) complete all as directed.

S&F in repairs stainless steel sink 1.0mm thick for kitchen with drain board of overall size 915x460mm & bowl size of 410x330mmx160mm including all necessary fixing arrangements as required at site complete all as directed.

Resecuring the shutters of any description of area exc 1sqm and n exc 2sqm each after carrying out necessary repair complete all as directed.

Taking down shutters of any description of area exc 1sqm and n exc 2sqm each and carry out necessary repair and refixing in same opening complete all as directed.

S&F in repairs mild steel butt hinges, medium weight cold rolled of size 100mm complete all as directed.

S&F in repairs aluminium handle cast type anodised of size 150mm complete all as directed.

S&F in repairs aliminium handles, cast type, anodised of size 125mm complete all as directed.

S&F in repairs150mm long aluminium anodised , barrel tower bolts of extruded section complete all as directed.

S&F in repairs125mm long aluminium anodised , barrel tower bolts of extruded section complete all as directed.

S& Fix in repairs floor door stoppers of aluminium alloy body with steel spring of size 150mm fixed to door complete all as directed.

S&F in repairs 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections complete all as directed.

S&F in repairs 300mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts four on bolt plate and two on staple plate complete all as directed.

Hacking out old broken glass (any thickness, size quality or description) from wood /steel frame, glazed with oil putty or fixed with beads and height upto 4 floors and S&F plain sheet glass of 3 mm thick ordinary quality and glazing with oil putty and clips in squares not exceeding 0.50 Sqm in each pane complete all as directed.

Hacking out old broken glass (any thickness, size quality or description) from wood /steel frame glazed with oil putty or fixed with beads and height upto 4 floors and S&F 3 mm thick frosted glass pin headed and glazing with oil putty and clips in squares exceeding 0.50 Sqm in each pane complete all as directed.

S&F in repairs galvanised mild steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with 2nd class hard wood beading suitable for existing wooden doors including making holes/ cutting rusted bolts and nuts on steel windows and provision of new nuts and bolts suitable for MS beading complete all as directed.

M&L in repair for prelaminated particle board 19mm thick, interior grade, prelaminated on one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete including dismantling of existing damaged boarding all as directed.

M&L in 6mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work all as irected.

M&L in 12mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work all as irected.

S&F in repairs continuous (piano) hinges of flap width 30mm, mild steel, bright finish or electo galvanised complete all as directed.

S&F in repair Stainless steel curtain rods of 25mm dia including taking down the existing.

S&F in repairs SS ornamental stainless steel holding brackets for 28mm dia curtain rods.

Supply and fix in repairs single action spring hinges mild steel with steel wire springs stove enameled black 125mm long with necessary screws/welding complete all as directed.

S&F in repairs MS handles of sides (L/R) stove enamelled black suitable for glazed steel window/ventilator complete all as directed.

S&F in repairs MS peg stay stove enamelled black suitable for glazed steel window/ventilator complete all as directed.

S&F stainless steel plate rack of size 30"x36"x10" made out of 1mm thick sheet complete all as directed.

M&L for Brick work with sub- class 'B' old size bricks straight or curved on plan to any radius in half brick thick wall in cement mortar (1:4) including demolition of existing brick work complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) including demolition of old brick work complete all as directed.

M&L for rendering 10 mm thick in CM (1:6) on brick or concrete surfaces finished even and smooth without using extra cement and prepration of newly plastered surfaces of wall and applying three coats of white wash complete all as directed.

M&L for rendering 10 mm thick in CM (1:6) on brick or concrete surfaces finished even and smooth without using extra cement including taking down cement plaster on brick/concrete/stone masnory surfaces of any description including racking out joints, hacking for key and scrubbing down with water and prepration of newly plastered surfaces of wall and applying two coats of oil bound distamper over a coat of alkali resistant primer over a coat of luppam fininsh of 1.5mm thick, complete all as directed. Note : Rate quoted shall be inclusive of necessary scaffolding etc up to 4th storyed building.

M&L rendering 5mm thick in CM 1:4 on ceilings, finished even & smooth and providing three coats of white wash after preparation of new surface including taking down existing plastering complete all as directed.

Rendering 15mm thick in cement mortar CM (1:4) in two layers (First coat 10 mm thick and second 5 mm thick)using water proofing compound in 2nd layer @2% by weight of cement and finished fair and even complete all as specified and as directed including taking down cement plaster on brick/concrete/stone masnory surfaces of any description and racking out joints, hacking for key and scrubbing down with water complete including preparation of surfaces and applying two coats of cement base paint over a coat of primer. Note : WPC will be measured and paid separetly. Note : Rate quoted shall be inclusive of necessary scaffolding etc up to 4th storyed building.

Supply only integral waterproofing compound complete all as directed

M&L non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) first quality area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 15mm thick screed bed in cement mortar 1:6 including dismantling existing tiles with screed bed complete all as directed.

M&L non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) first quality area of each tile exceeding 0.18 but not exceeding 0.38 sqm, in floors etc jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 15mm thick screed bed in cement mortar 1:6 including dismantling existing tiles with screed bed complete all as directed.

M&L for glazed ceramic tiles of size 300x450x7 mm thick vertical surfaces such as skirting/dado jointed in neat cement slurry and pointed with white or coloured cement to match the colour of the tiles laid on and including 10mm thick rendering in cement mortar 1:4 including dismantling of existing tiles along with a backing coat complete all as directed.

M&L for Granite (of any type) tiles 18 to 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting,rounding edges and polishing laid on and including 15mm thick screed bed in cement mortar 1:6 including taking down existing stone slab/ tile complete all as directed.

Taking down door chowkhats of area exc 1.5 sqm but not exc 4 sqm each with shutter (without taking off shutter from the frames) complete all as directed.

Taking down door chowkhats of area n exc 1.5 sqm each with shutter (without taking off shutter from the frames) complete all as directed.

Taking down shutters of any description exc 1 sqm but n.exc 2 sqm complete all as directed.

S&F factory made solid PVC door frame of size 50x47 mm made out of 5mm thick plain colour PVC sheet reinforced with M.S. Square tube 19mm x 19 mm of gauge complete all as directed.

S & F Factory made solid panel PVC moulded door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame including two nos of 100mm long tower bolt, 02Nos of 100mm long Aluminium Handle 03 Nos of Aluminium hinges of size 100mm at site complete all as directed.

S&F 2nd class hard wood 35 mm thick factory made panelled shutter (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered partical board with commercial veneering on both faces The size of rail and stile as per IS :1003 part 1) , kiln seasoned and chemically pressure treated including preparation of surface and applying 2 coats of synthetic enamel paint over a coat of pink primer complete all as directed.

S&F 2nd class hard wood Glazed skelton shutters 35 mm thick open rebated and prepared to receive glass, gauze etc. (without sash bars) including preparation of surface and applying 2 coats of synthetic enamel paint over a coat of pink primer complete all as directed.

S&F 30mm thick flush shutters, solid core construction with block board and plywood face panels, commercial type on both sides including preparation of surface and applying 2 coats of synthetic enamel paint over a coat of pink primer complete all as directed.

S&F factory made uPVC top hung glazed and wire gauzed ventilator made of frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and glazed shutter with plain glass 3 mm thick pin head/frosted glass alongwith mosquito proofing shutter with stainless steel wire cloth 0.254 mm (30 gauge) dia of steel wire and 0.95 mm width of aperature,single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, Reinforced with G/J/U/O shape galvanised MS section considering structural/wind load requirements. Ventilator to be provided with proper operative and locking hardware mechanism, including taking down old ventilators all as specifed.

Supply & fixing of UPVC windows three track sliding window with two glazed and one wire mesh sliding shutters of profile width of frame 50 mm to 60 mm, limit thermal conductivity to l.3 Kcal/sqm/hr centigrade, sound insulation up to 4-0 bds, Density, 1.46 gm/ml, Tenstile strength - 43.9N/sqmm, % Elongation at break - 215, Tenstile mpduls - 2840N/Sqmm, Flexural strength - 51N/sqmm, Heat aging at 150 degrees - No surface defect, Thickness - 2 mm, Flexural moduls elasticity 2200N / sqmm, double baskets & wool pile on window, multi point gear locking at different sides of frame, anti lift device on slide windows with temper proof screws with and including glazed shutter fixed with 5 mm thick plain sheet glass & wire mesh shutter with stain less steel wire cloth 304 grade stainless steel with 0.254 mm (30 gauge) dia of steel wire and 0.95 mm width of aperature and filling gap of wall and frame with silicon sealent complete incl taking down old down old window complete all as specified. all as directed .

S&F galvanised mild steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks for wooden doors with nut and bolts suitable for MS beading for steel windows complete all as directed.

M&L in repairs to joints of tiles flooring in toilet and bathroom using white cement including racking out old cemet joints complete all as directed.

M&L for 75mm thick plain cement concrete1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection including providing 10mm thick joints filled with bituminous & sand mixture (1:7) at not exc 3.00 mt intervals & at corners and finished even and smooth without using extra cement including demolition of existing concrete complete all as directed.

M & L for plain cement concrete(1:3:6) type C-2 (using 40 mm graded stone aggregate) of 100 mm thick as in Path / PCC floor, finished even and fair including demolition of existing concrete complete all as directed.

M&L for coloured chequered cement concrete tiles 25mm thick,of any shape and size not less than 0.09 sqm in each tiles, set and jointed, pointed in neat cement slurry in floors with grey cement and pigment over 15mm thick screed in cement mortar (1:6) including dismantiling of existing tiles complete all as directed.

S & F TMT bars, 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with & including MS wire (annealed) not less than 0.9mm dia or securing with clips.

M&L precast cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate ) in landings cover slabs for man holes etc.) chullah hoods, chajjas, water troughs, shelves and similar articles with plain faces including necessary form work and demolition of existing concrete complete all as directed. Note: Reinforcement shall be measured & paid seperately.

S&F in repairs rotational moulded polyethylene water storage tank of 1000 litres capacity cylinderical vertical type double layered with closed top hoisted including taking down existing water tank complete all as directed.

S&F in repairs waste Pipe of 32/40 mm dia of (length 0.90 mtr) PTMTsuitable for wash basin/ sink half or full threaded complete all as directed.

S&F in repair for 100mm Stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays. Including bolts and nuts and securing ends of stays to wall or roof

S&F in repair for 75mm Stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays. Including bolts and nuts and securing ends of stays to wall or roof

S&F cast iron waste and vent pipes (sand cast) in any length with or without ears with run lead joints laid in floors 75m bore sand cast pipe ISI marked includng dismantling of old unserviceable cast iron pipes, complete all as directed.

S & F CI bends/Y (any radius), diminishing pieces or tapers suitable for 75mm bore pipe includng dismantling of old un serviceable cast iron fittings complete all as directed.

S&F cast iron soil and vent pipes of 100mm bore (sand cast) in any length with or without ears, with cement joints fixed to walls with and including clamps and dismantling of old unserviceable cast iron pipes complete all as directed.

CI bends/Y (any radius), diminishing pieces or tapers suitable for 100mm bore pipe includng dismantling of old unserviceable cast iron fittings complete all as directed

S&F PVC (SWR) pipes 110mm bore, single socketed in any length with rubber ring joints fixed to wall includng dismantling of old unserviceable PVC pipe complete all as directed.

S&F PVC (SWR) bends 110mm dia complete includng dismantling of old unserviceable PVC bends complete all as directed.

Complete removal of trees/plants, upto roots growth on bldg's roofs, chajjas, at junctions of pipe line fixed on walls and walls coming on bldgs and removing the material (Branches and plants ) to a distance n.exc 50m complete all as directed Note : Work to be carried out up to 06 storey building.

S&F in mild steel butt hinges, medium weight cold rolled of size 100mm complete all as directed.

S&F in aluminium handle cast type anodised of size 150mm complete all as directed.

S&F in aluminium handles, cast type, anodised of size 125mm complete all as directed.

S&F in 150mm long aluminium anodised , barrel tower bolts of extruded section complete all as directed.

S&F in 125mm long aluminium anodised , barrel tower bolts of extruded section complete all as directed.

S& Fix in floor door stopper of aluminium alloy body with steel spring of size 150mm fixed to door complete all as directed.

S&F in 300mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts four on bolt plate and two on staple plate complete all as directed.

Digging out and removing sunken floor filling and depositing the same at a distance not exceeding 250m away from the outer edge of bldg complete all as directed.

M&L for pain cement concrete 1:5:10 type E2, (using 40 mm graded stone aggregate) as in filling of sunken floors complete all as directed.

M&L for 10mm thick rendering on concrete/brick surfaces in CM 1:4 duly mixed with water proofing compound @ 2% by the weight of cement and finished even and smooth without using extra cement complete all as directed. Note : water proofing compound shall be measured and paid separately.

Supply only integral water proofing compound complete all as directed.

M&L for applying two coats of NITOBOND SBR polymer modified coating to a thickness of 1mm, 1st Coat (Nitobond SBR Chemical 1 ltr, Water 2 Ltrs, Cement 3 Kg) Second Coat (Nitobond SBR Chemical 1 ltr, Cement 3 Kg) applied thoroughly without any traces of dirt or laitance as in sunken floors complete all as directed.

Dismantling Asbestos Cement (Corrugated, Semi corrugated etc.) sheets in roof coverings.

M & L Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M & L Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S/F Anodised aluminium snap grid frame work for false ceiling all as specified

Fixing only Anodised aluminium snap grid frame work for false ceiling all as specified

S&F Perforated particle board/tiles for insulation and acoustic purposes, 60x60 cm in size, fixed with nails to timber frame work or with staples on snap grid complete all as specified.

Anjana corporation (BID ID -3413842)

Ravi Enterprises (BID ID -3413732)

SRI SAI ENTERPRISES (BID ID -3397006)

rahi consultant (BID ID -3413598)

M/s ANUSHA ENTERPRISES (BID ID -3413675)

Indu Electricals (BID ID -3414327)

PAVAN ENTERPRISES (BID ID -3399205)

SM CONSTRUCTIONS (BID ID -3399779)

WELDECOR (BID ID -3397187)