ADDITION/ALTERATION AND SPECIAL REPAIRS TO SELECTED OLD MD ACCN AT BABINA.

Amount

Note: (i) Please refer schedule 'A' notes before quoting the tender. (ii) Amount of Schedule of credit shall be deducted off line by the department.

Demolition of existing roof treatment of any description and in any position at site with APP/PCC and 10mm thick backing coat below APP complete all as specified and as directed.

M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in padding over roof; surface finished and laid to required slope complete all as specified and as directed.

Cutting grooves in brick wall 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed.

M&L for 10 mm thick rendering in cement mortar 1:4 on concrete surfaces when concrete is still green; finished even and fair including mixing of water proofing compound as per manufacturer instructions, etc complete all as specified and as directed. Note :- Water proofing compound shall be measured and paid separately as supply only.

Supply only integral water proofing compound complete all as specified and as directed.

M&L applying water proofing treatment with the following:- (a) First coat of bitumen primer conforming to IS-3384 @ 0.3Kg / sqm to be applied on prepared surface till the surface is properly impregnated. (b) After the application of approved bituminous primer the water proofing memberne minimum weight 3kg/sqm and minimum 3mm thick reinforced with polyester non woven fabric (weight not less then 160gms/sqm) shall be laid on the primed surface by torch application method as per manufactures instruction. (c) All joints and change in direction should be curved with cement mortar (1:3) mixed with SBR latex @ 200ml per bag on cement and cured well before laying of membrane. NOTE:- (i) Work of water proofing treatment shall be carried out by authorised applicator of the manufacturer. Necessary documentary evidence in support of the authorised applicator will be submitted to Engineer-in-charge before the commencement of water proofing work. (ii) The quoted rates is deemed to include for the cost of scaffolding, T&P, etc required for execution of the work.

M&L for toping layer of precast machine pressed cement concrete tiles of size 25cm x 25cm x 22 mm thick laid in neat cement slurry over and including 15 mm thick cement mortar screed in 1:4 and joints between the tiles to be filled with grey cement and no pigment complete all as specified and directed.

Taking up or down existing steel tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed for the following sizes:-

15 mm bore

20 mm bore

Supplying, fixing, jointing and testing galvanised iron tubing medium grade with all fitting such as bends, elbow, socket, reducer etc and fixed to wall or laid in floor complete all as specified and as directed for the following sizes:-

15 mm bore

20 mm bore

Fixing only old steel tubing and connections obtained from taking down against item No.10.00 & 11.00 herein before in new or old position fixed to wall, ceiling or laid in floor with new fittings for the following sizes:-

15 mm bore

20 mm bore

S&F Rotational moulded (three layered) polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity including PVC cover, hoisted and fixed in position including connecting up pipes complete all as specified and directed.

Dismantling of 500 liter water tanks, any type complete all as specified and as directed.

S&F 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minium weight 210 gms) complete all as specified and directed.

S&F in repairs 20mm dia Gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

Demolition of PCC of any description and in any position, etc complete all as specified and as directed.

M&L for 40mm thick cement concrete type B-1:2:4 (using 20mm graded stone aggregate), finished even & smooth without using extra cement complete all as specified and as directed.

S&F Glass dividing strips, 3mm thick and 38mm wide, inserted in position in floors complete all as specified and directed.

M&L for 25mm thick Cement concrete 1:2:4 type B-0(using 12.5mm graded aggregate) as in flooring complete all as specified and as directed.

M&L for non-skid, coloured, joint free, ceramic tiles 7 to 8 mm thick (square / rectengular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to tile, etc with & including 15 mm screed bed in CM(1:4) complete all as specified and as directed.

M&L for non-skid, coloured, joint free, ceramic tiles 7 to 8 mm thick (square / rectengular) area of each tile exceeding 0.06 sqm but not exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to tile, etc with & including 15 mm screed bed in CM(1:4) complete all as specified and as directed.

M&L for non-skid coloured joint free ceramic tiles 7 to 8 mm thick (square / rectengular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm, in Skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match to tiles, etc with and including rendering 10mm thick on fair faces of wall or conc surfaces in CM 1:4 finished rough for wall tiling etc complete all as specified and as directed.

M&L for joint free glazed coloured tiles 300 x 200 x 7mm thick for work on vertical surfaces, etc set & jointed in cement slurry and pointed in white or coloured cement to match tile, etc with and including rendering 10mm thick on fair faces of wall or concrete surfaces in CM 1:4 surface finished rough for wall tiling complete all as specified and as directed

M&L for Cement concrete 1:3:6 type C1 using 20mm graded stone aggregate in plinth protection, 75mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 meters and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and directed.

M&L for 25 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including grinding, moulding, etc with and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

Taking down cement plaster on brick or stone wall including raking out joints, hocking for key scrubbing down with water etc. complete all as specified and as directed.

M&L for rendering 10mm thick on fair faces of concrete/brick surfaces in CM 1:6, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 5mm thick in cement mortar 1:3 on ceiling surfaces, surface finished even and smooth without using extra cment complete all as specified and as directed.

M&L for rendering 15mm thick on fair faces of concrete/brick surfaces in CM 1:4, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of new plastered surfaces and applying three coats of white wash on ceiling complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of OBD over a coat of primer complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint on external wall surface over a coat of primer complete all as specified and as directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame), area exe 1.5 Sqm but n exc 4 Sqm each complete all as specified and as directed

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) area not exe 1.5 Sqm each complete all as specified and as directed.

Taking down shutters of any description exc 1 sqm and n.exc 2 Sqm each complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck in side with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail,paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as specified and as directed.

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube etc complete all as specified and as directed.

S&F aluminum anodized barrel tower bolts of extruded section, 150 mm long complete all as specified and as directed

S&F aluminum handles, cast type anodized 150 mm size complete all as specified and as directed

S&F 150mm floor door stopper, aluminium alloy body complete all as specified and directed.

S&F Butt hinges medium weight cold rolled, mild steel and fixed 100 mm size complete all as specified and as directed.

S&F Butt hinges extruded aluminium alloy with galvanised mild steel hing pin, anodised and fixed, type C-21 100 mm size in toilet for PVC doors complete all as specified and as directed.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy complete all as specified and as directed.

Cutting holes in brick walls built in cement mortar for inserting hold fasts and making good dismantled portion in CM 1:3 or cement conc 1:2:4 type B1 as required exc half brick but not exc full brick wall complete all as specified and as directed.

S&F mild steel flat iron 25x3 mm as in hold fasts, etc confirming to Fe 410-0 or Fe 310-0 complete all as specified and as directed.

M&L PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in filling in holes of hold fasts and back filling of chowkats complete all as specified and directed.

S&F of framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete of Fe-410-W (Gde-E-250) complete all as specified and as directed.

S&F Pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

S&F Pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

M&L for Second class hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

S&F 18/19 mm thick prelaminated particle board interior grade prelaminated one side with decorative choice laminations and other side balancing white lamination fixed with screws to timber frame work, etc complete all as specified and as directed.

S&F 19 mm cover fillet of external teak wood lipping 6mm thick fixed with nail complete all as specified and as directed.

S&F Hasp & staple safety type aluminium anodized with mild steel hing pin incl bolt to hing plate and fixed with screws 100mm size etc complete all as specified and as directed.

S&F 1.25 mm thick mild steel, plain black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc complete all as specified and as directed

S&F of 35mm thick 2nd class Hard wood paneled door shutter factory made (two panel) with lock rail andpanel of 9mm thick BWP commercial ply wood, the size of rail and stile is as per IS 1003 (Part-I), Kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F factory made fabricated 35 mm thick IInd class HW glazed & skeleton shutters open rebated and prepared to receive glass gauge etc. (without sash bars) edges of framing plain chamfered or rounded fitted with cut & mitered beads for security glass/gauge etc. size of members of shutter as specified in SSR Pt I sec 8 Cl 8.20 (a), divided into squares with plain chamfered rounded, mitered and rebated sash bars etc complete all as specified and as directed.

S&F galvanized mild steel wire cloth 0.63 mm nominal dia of wire and avg width of a-pertare 1.40 mm fixed with tinned tacks or galvanized wire staples etc complete all as specified and as directed.

M&L for preparation new wooden surface of any description not otherwise described over 10 cm width or girth and applying two coat synthetic enamel paint over one coat of pink primer, etc complete all as specified and as directed

M&L for applying of one coat synthetic enamel paint on old wooden surface incl preparttion of old surface of any description not otherwise described over 10 cm width or girth etc complete all as specified and as directed.

S&F of CRC steel sheet box type steel window with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F of CRC steel sheet box type steel window with steel handle, and steel peg stay, complete with out glazing bars, dovetailed or welded complete all as specified and as directed.

S&F of CRC steel sheet box type steel ventilator with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F of CRC steel sheet box type steel ventilator with steel handle, and steel peg stay, complete with out glazing bars, dovetailed or welded complete all as specified and as directed.

S&F Mild steel conforming to Fe-290 Gde E-165 in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work complete all as specified and directed.

S&F 3 mm thick sheet glass, ordinary quality and glazing with putty in square, area n. exc 0.5 Sqm in each pane complete all as specified and as directed.

S&F 3 mm thick figured glass, pin head type and glazing with oil putty in squares area exc 0.5 sq.m in each pane complete all as specified and as directed.

S&F in repairs 3 mm thick sheet glass, ordinary quality and glazing with putty or fixed in existing window and area of each pan not exc 0.5 Sqm complete all as specified and as directed.

M&L for Preparing new or previously untreated steel & iron surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over & including a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for Preparing old painted steel & iron surfaces of any description over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F in repairs vitreous china squatting pan “ORISSA” pattern size 580mm X 440mm, white coloured, with P or S trap front or back inlet with integral foot rest (excluding flushing cistern & flush pipe) & including connection to trap & to flushing pipe anti-syphonage pipe, etc complete including making good to floor complete all as specified and as directed.

S&F in repairs PVC low level flushing cistern 10 liters capacity dual flush, ISI marked, white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe 600mm long, complete all as specified and directed.

S&F in repairs Vitreous china wash basin, ISI marked, white, flat back, size 550 x 400mm, including CP waste coupling, 32mm dia PVC waste pipe of suitable length, brackets and cutting for and pinning in ends of brackets, complete all as specified and directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm etc complete all as specified and as directed.

S&F in repairs Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions 15mm bore complete all as specified and directed.

S&F in repair Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (angle type) screwed both ends for iron pipe or for unions 15mm bore, complete all as specified and directed.

S&F in repairs Bib tap long body with flange, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and directed.

S&F wash basin mixture, centre hole, cast copper alloy, screwed down, high pressure, with capstan head, fancy type, chromium plated screwed for iron pipe or for unions 15mm bore, complete all as specified and directed.

S&F Cast iron floor trap with grating including jointing to waste pipe in cement concrete type B-1 (1:2:4), dia of outlet 75mm complete all as specified and directed.

S&F Cast iron Nahani trap with grating including jointing to waste pipe in cement concrete type B-1 (1:2:4), dia of outlet 75mm complete all as specified and directed.

S&F in repairs of CP Towel rail, 20mm dia, D type 600mm long between flanges complete all as specified and directed.

S&F in repairs 125 mm size brass chromium plated shower rose with or without swivel joints, including fixing of steel pipe or union and fixed complete all as specified and as directed.

Refixing shutter exceeding 1 Sqm but not exceeding 2 Sqm each in the same opening after taking down, as required complete all as specified and directed.

S&F stainless steel plate rack of minimum size 36” x 36" x 10” fixed with screws on wall complete all as specified and directed.

S&F in repairs Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size:- 914mm x 460mm x 203, bowl size:- 405mm x 354mm x 203mm, including CP waste coupling and 32mm dia PVC waste pipe of suitable length complete all as specified and directed.

S&F in repairs 25 mm dia chromium plate curtain rod with CP brackets and knobs at both end as per sample approved by Engineer-in-charge complete all as specified and as directed. .

Demolition and breaking up drain pipes (Salt glazed ware, AC/PVC/CI or Reinforced concrete) set in cement mortar in floors or wall in 100mm dia complete all as specified and as directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with clamp out of 25x3mm flat Iron including bolts and nuts 110mm bore complete all as specified and as directed.

S&F of 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

S&F PVC (SWR) pipes single socketed, in any length with clamp out of 25x3mm flat Iron including bolts and nuts rubber ring joints, fixed to wall 75 mm bore complete all as specified and as directed.

S&F of 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

S&F PVC (SWR) bends any radius 110mm bore complete all as specified and as directed.

S&F PVC (SWR) bends any radius 75mm bore complete all as specified and as directed.

S&F PVC (SWR) junction single, (single T) equal or unequal 75mm bore with access door complete all as specified and as directed.

S&F PVC (SWR) junction single, (single T) equal or unequal 110mm bore with access door complete all as specified and as directed.

S&F PVC (SWR) vent cowl 110mm bore complete all as specified and as directed.

M&L for Preparing old plastered/unplastered surfaces of ceilings and applying one coat of white wash complete all as specified and directed.

M&L for Preparing old plastered/unplastered surfaces of wall and applying one coat of white wash complete all as specified and directed.

M&L for Factory made, machine pressed, M-35 grade concrete interlocking paver blocks (glossy/reflective type), with grey cement and pigment, any shape and size conforming to IS:15658-2006 (ISI Marked) of 60 mm thickness complete all as specified and directed.

M&L PCC 1:4:8 type D2 using 40mm graded stone aggregate as in filling and mass concrete, sub-base/flooring, etc complete all as specified and directed.

M&L 50mm thick sand cushioing to under concrete interlocking paver block including watering & consolidation complete all as specified and as directed.

Demolition of brick work built in cement or cement lime mortar complete all as specified and directed.

M&L for Brick work with fly ash bricks (Modular), straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

S&F MS chromium plated peg set of five fixing with wall complete all as specified and as directed.

Dismantling of stone slabs and tiles of any description or thickness in floore aprons etc laid bedded and pointed in any mortar complete all as specified and as directed.

M&L sand stone slabs in sunshades, chajjas, shelves, cills, landings, man hole cover, stones templates etc n exc 2m in length punched dressed on face and along exposed edges self faced on other side and set and pointed in cement mortar 1:4 thickness of slab 5cm complete all as specified and as directed.

Demolition of Reinforced concrete of any description and in any position not otherwise specifically provide for complete all as specified and as directed.

M&L for Formwork to chullah hoods, chajjas, troughs and similar items including edges for fair finished flat surfaces of concrete complete all as specified and directed.

M&L for TMT mild steel bars 6 mm to 8 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for Reinforced cement concrete design mix M-25 in chajjas complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar of 150mm dia complete all as specified and as directed.

S&F salt glazed stoneware drain pipes 150mm bore, grade ‘A’, laid in trenches and jointed as specified complete all as specified and directed.

M&L for Concrete bed to drain pipes 150mm bore including packing under and completely surrounding pipes with concrete after they are laid and tasted; in cement concrete 1:4:8 type D2 using 40mm graded stone aggregate complete all as specified and directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in any type of soil complete all as specified and directed.

Returning filling in including spreading ,levelling,watering and well ramming in layers not exc 25cm complete all as specified and as directed.

Removing excavated soil to a distance not exceeding 50m and depositing where directed. at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L for soakage wells of size 1.8 M dia X 3.0 M effective depth including excvation in any type of soil, foundation in PCC 1:3:6, wells of Honey combed and solid in M-25 Concrete, including intercepting chamber, screen chamber, Brick work in CM, RCC cover slab in M-25/ RR masonry / Filling with brick bats, complete all asspecified and shown in drawing No.CEBZ/TD/78/2011 Sheet 1/2 & 2/2. Note :- All Excavations, returning filling and removing of surplus soil is deemed to be included in the quoted unit rate.

M&L for RCC Septic tank for 100 users conventional type designed to carry sewage and sullage water including excavation & earth work in any type of soil, foundation in PCC (1:2:4), brick work in CM (1:4), RCC ( M-25) slab cover including necessary man hole cover, vent pipe and sludge chamber, etc complete all as specified, directed and shown on drawing No CEBZ/TD/76/2011, Sheet- 1/2 to 2/2. Note :- All Excavations, returning filling and removing of surplus soil is deemed to be included in the quoted unit rate.

Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means including filling depressions of scrapped surfaces with putty and preparation of surfaces for further treatment and M&L for applying two coats of distemper oil emulsion, white or tinted over one coat of primer complete all as specified and directed.

Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means including filling depressions of scrapped surfaces with putty and preparation of surfaces for further treatment and M&L for applying two coats of cement base paint, white or tinted over one coat of primer complete all as specified and directed.

M&L for Water proofing treatment to roof surfaces with polymeric water proofing membrane weighing not less that 3 Kg/Sqm, consisting of 90 micron center core of HMHDPE (High Molecular High Density Polyethylene) film covered with high quality polymeric asphaltic protected with thermo fusible HMHDPE film on both sides, over a coat of hot blown grade bitumen 85/25 @ 1.20 Kg/Sqm over a coat of bitumen primer @ 0.30 Ltr/Sqm, un-rolled & bonded completely to substrata and over laps (10 cm) sealed by flame and finished with another coat of hot blown grade bitumen 85/25 @ 1.20 Kg/Sqm and applying a coat of aluminium paint @ 100 gm/Sqm (minimum) as per manufacturer’s instructions and guidance complete all as specified and directed.

M&L rendering 15mm thick in CM 1:3 on fair faces of brick/concrete surfaces of sunken floors mixed with water proofing compound (water proofing compound to be measured & paid separately as supply only) and finished fair and even complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and as directed.

M&L for applying 3mm thick wall care putty complete all as specified and directed.

Taking down aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, sockets, etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc and removing materials from the site complete all as specified and directed.

M&L for point wiring with PVC insulated unsheathed FRLS/FRLSH 1100 volts grade single core muilt stranded copper conductor cables of size 1.5 sqmm for phase & neutral in and existing concealed 20/25mm dia PVC conduits, sheet steel sunken boxes 1.2mm thickness covered inculding with 3mm thick plastic laminated sheet for mounting switches, scockets, regulator, etc and including 1.5 Sqmm copper conductor PVC insulated and unsheathed multi stranded green cable as earth wire for one light point/fan point / buzzer point controlled by one switch complete all as specified and directed. Note:- (i) Quoted Unit rate is deemed to include for cutting chases and making good the disturbed surface to match with the original. Nothing extra shall be paid on this account.

M&L for point wiring with PVC insulated unsheathed FRLS/FRLSH 1100 volts grade single core muilt stranded copper conductor cables of size 1.5 sqmm for phase & neutral in and existing concealed 20/25mm dia PVC conduits, sheet steel sunken boxes1.2mm thickness covered inculding with 3mm thick plastic laminated sheet for mounting switches, scockets, regulator etc and including 1.5 Sqmm copper conductor PVC insulated and unsheathed multi stranded green cable as earth wire for one light point controlled by two way switch complete all as specified and directed. Note:- (i) Quoted Unit rate is deemed to include for cutting chases and making good the disturbed surface to match with the original. Nothing extra shall be paid on this account.

All as per BOQ Serial Item No.132.00 above but for one socket outlet 3pin, 5 Amps on the same board complete all as specified and directed.

All as per BOQ Serial Item No.132.00 above but for one socket outlet 3pin, 5 Amps on the independent board complete all as specified and directed.

All as per BOQ Serial Item No.132.00 above but for one socket outlet 3 pin 15 Amps on independent board using cable of size 2.5 Sqmm for phase & neutral and 2.5 Sqmm as earth wire complete all as specified and directed.

S&F lamp holder PVC/polycarbonate type with back plate complete all as specified and directed.

S&F switch piano flush type, single pole, 230 volt, one way, 5 Amps complete all as specified and directed.

S&F switch piano flush type, single pole, 230 volt two way, 5 Amps complete all as specified and directed.

S&F switch piano flush type, single pole, 230 volt one way, 15 Amps complete all as specified and directed.

S&F bell push piano type, Single Pole, 230 volts complete all as specified and directed.

S&F Socket out let, 2 in 1, 3 pin 5 Amps, ISI marked, 230 Volts complete all as specified and directed.

S&F Socket out let 2 in 1, 3 pin 5/15 Amps, ISI marked, 230 Volts complete all as specified and directed.

S&F stepped type (switch type) electronic ceiling fan regulator flush type, AC, 230 volts, complete all as specified and directed. Note: Regulator and switch/socket will be of the same make

S&F ceiling rose, surface type bakelite 65x17.5 mm, three terminals complete all as specified and directed.

S&F Electric bell, AC, 230 volt, single pole, Ding Dong type complete all as specified and directed.

Taking down carefully ceiling fan / exhaust fan / geyser of any type/sweep/capacity after disconnecting the electric connections, shifting to store yard for keeping in safe custody and refixing the same and making electrical connections complete all as specified and directed.

S&F light fitting LED 20/22 watt, 6000K, 230 volt, LED batten with epoxy powder coated extruded aluminium heat sink channel housing, cover made of high quality polycarbonate diffuswer for glare free light distribution, in-built electronic driver, bipin holders, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed.

S&F LED lamp 9watt capacity complete all as specified and directed.

S&F Bulk head fitting in engineering plastic housing with clear prismatic diffuser 10 watt capacity complete all as specified and directed.

Disconnecting the power supply and taking down old unserviceable DBs/junction box/panels ect of any type and size complete along with all MCCBs/MCBs, etc complete all as specified and directed.

S&F MCCB distribution board TPN, 4 way, 415 volts, double door (metallic type) with 200 Amps rated bus bar, neutral bar with shrouds, earth bar, IP-54, made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCCBs as incomer and outgoing 4 way including blanking plate complete all as specified and directed. Note: MCCB DB and MCB SP/SPN will be of same make.

S&F MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door (metallic type), IP-43, made out of sheet steel enclosure, recessed type, factory made powder coated, 8 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed. Note: MCB DB and MCB SP/SPN will be of same make.

S&F MCCB, 4 pole, 100 amps having rapturing capacity 16kA, 415 Volts, 50 Hz, conformning to IS:13947-2 & IEC 60947-2, fixed thermal magnetic release type, Ics=100% Icu with adjustable overload setting and adjustable short circuit setting, flush mounting by providing suitable nuts, bolts, washers, etc complete all as specified and directed.

S&F MCB SP, 240 volts, 10 KA breaking capacity, 'C' curve, of capacity 6 to 32 amps complete all as specified and directed.

S&F MCB SPN, 240 volts, 10 KA breaking capacity, 'C' curve, of capacity 40 amps complete all as specified and directed.

S&F MCB SPN, 240 volts, 10 KA breaking capacity, 'C' curve, of capacity 63 amps complete all as specified and directed.

Taking down unserviceable sub main wiring including service connections, of any size and any description including conduit pipe and making good disturbed surface of wall/ceiling to match with existing surface after necessary rewiring complete all as specified and directed.

M&L for sub main wiring with approved colour code as per IS with two runs of single core (FRLS/FRLSH) PVC insulated with multi strand copper conductor of size 6.00 sqmm nominal cross sectional area drawn in & including non metallic rigid PVC conduit (ISI marked) medium grade not less than 25mm diameter with all conduit accessories in concealed wiring system by cutting of walls (brick or stone) and making good disturbed surface of wall in CM 1:3 including one runs of single core FLRS/FRLSH PVC insullated 6.00 sq. mm ( nominal area) stranded copper conductor as earth wire complete all as specified and directed. Note: - Two runs of 6.0 sqmm cable, one run of 6.00 sqmm cable of earth continuity conductor & PVC conduit pipe shall be measured as one unit length.

M&L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground vertically to a depth not less than 3.0m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI medium grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 complete all as specified and directed. NOTE :- (i) The concrete pit shall be PCC (1:3:6) type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I. (ii) The unit rate includes the cost of GI pipe medium grade for protection of earth wire and 4mm dia earh lead wire upto 7.5 M. (iii) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself.

Taking down existing vintage HPSV/CFL/ LED type security Light fitting and S&F Energy efficient LED type street light fitting, Pressure die cast aluminium housing with heat resistant toughened glass & IP66 protection, 35 watts (with lens) with Luminous Efficacy more than 100 Lm and Power Factor not less than 0.95 complete all as specified and directed.

S&F GI bracket made out of 32mm bore GI pipe light grade, 1.20 mtr long bend to shape or size as directed at site for mounting building light complete all as specified and directed.

S&F exhaust fan 300 mm sweep, metal body with louver shutter suitable for 230 Volts, Single phase 50 Hz AC supply,connecting with three core flexibale copper cable including making hole for fixing of fan and making good the disturbed surfaces of wall complete all as specified and directed.

Supply, fixing, connecting and testing of electric water heater (Geyser) stationary storage type, closed / vented type, vertical, including inner container of stainless steel, capacity 25 Ltrs, 240 volts, 2000 Watts heating element, 5 star ratting with anchor fastner, nuts, bolts and washer etc, with power cable 6 Sqmm copper conductors complete all as specified and directed.

S&F sheet metal earth plug & socket, single pole and neutral with and including 1no. single pole MCB 20 Amps 240 volts complete all as specified and directed.

S&F PVC connection 450 mm long for cold/hot water heavy duty made out of double layer Nylon & wire fabric at pressure 6Kg/CM both side, CP brass 15mm bore coupling or nuts complete all as specified and directed.

S&F GI pipe 15mm bore, ISI marked, medium grade with all fittings like elbow, nipple, union, tees, socket, etc complete fixed on floor, on wall surface or concealed in wall / crossing the walll up to 30 cm thick for geyser inlet connection from tank outlet to gysers inlet and geysers outlet to bathroom tap/wash basin mixture connection with and including clamps, etc complete all as specified and directed. NOTE: In bathroom /near wash hand basin concealed GI pipe system shall be provided.

M&L for cutting & screwing existing steel tubing 20/15mm dia bore size for alternations or additions required for connection with inlet pipe of geyser complete all as specified and directed.

S&F gun metal, globe or gate valves 15 mm bore with iron wheel head, screwed both ends for iron pipes complete all as specified and directed.

Mata Builders

M/s R.V. Constructions