C/o Multipurpose Community Centre at Kamba

Amount

(SH:I Earth Work)

Earthwork in excavation over areas (exceeding 30 cm in depth, 1.50 m in width as well as 10 Sq.m. on plan) including disposal of surplus excavated earth lead upto 50 m and lift upto 1.50 m, disposed earth to be levelled and neatly dressed. b) Hard Soil

(c) Ordinary Rock (With or without blasting)

Earth work in excavation in foundation and trenches etc. in soil containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m.

Extra for every additional lift of 1.50 m or part thereof for earth work in all soils including shingles, small size boulders upto 30 cm size but excluding saturated soil and rock.

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

(SH:II .C.C Work)

Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone shingle 40 mm nominal size) excluding the cost of centring and shuttering.

Providing and laying cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone shingle 20 mm nominal size) excluding the cost of centring an shuttering in: b) Foundations and plinth

Providing and laying damp proof course 25 mm thick with cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm nominal size).

(SH:III R.C.C Work)

Reinforced concrete work in foundations, footings, bases of columns etc. in : a) M20(1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. a) M20(1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. a) M20(1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with M20 ( 1 cement: 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in stair cases (excluding landing) except spiral cases including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface, preparing of the top surface and finishing, nosing upto floor two level but excluding the cost of centring, shuttering and reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for : a) Foundation, footings, bases of columns etc. and mass concrete.

b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

d) Lintels, beams, girders, bressumers and cantilevers etc.

e) Column, pillars, posts and struts etc.

f) Stairs (excluding landings) except spiral stair cases.

Reinforcement of RCC work including bending, binding and placing in position complete. b) Tar/TMT Steel.

(SH:IV Brick Work)

Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand).

Extra for brick work with best available local bricks in superstructure above plinth level up to floor two level.

Extra for brick work in superstructure above floor two level, per floor per Cu.m. (1% of rate of brickwork from plinth up to floor two level). a) First Floor 1%

(SH:V Steel Work)

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately).

Supplying & Erection of MS Doors, Windows and Ventilators, work in single section including cutting, hoisting, fixing in position and applying a priming coat of red lead paint including all fittings complete. b) In Tees, Angles and Channels

Welding by Electric plant

Providing and fixing in position collapsible steel shutters with vertical channels 20 mm x 10 mm x 2 mm and braced with flat iron diagonals 20 mm x 5 mm size with top and bottom rails of T iron 40 mm x 40 mm x 6 mm with 38 mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles including applying a priming coat of red lead paint.

Providing and fixing flush door shutters, decorative type, core of black board construction with frame of 1st class hard wood and well matched 1st class teak ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. a) 40 mm thick including anodized aluminum butt hinges with necessary screws.

Providing and fixing glazing in MS door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge . 4.1) With float glass panes of 4.0 mm thickness.

Providing and fixing MS fan clamp type I of 16 mm dia MS bar bent to shape with hooked ends in RCC slabs during lying including painting the exposed portion of loop all as per standard design complete.

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws. b) Ornamental grill.

(SH:VI Flooring)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete b) Size of Tile 600x600 mm

White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanitycounters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. a) Granite of any colour and shade

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. A) Granite work

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : a) Medium shade using 50% white cement, 50% ordinary cement.

(SH: VII Roofing)

Providing corrugated Dyna sheet (Tata Brand) roofing fixed with appropriate Steenless steel screw with machine driver & as per the specification of manufacturer complete,excluding the cost of purlines, rafter & trusses.

Providing ridges or hips 60 cm overall in plain Dyna roof sheet fixed with J or L hooks, bolts and nuts 8 mm dia. limpet washers complete.

Providing and fixing suspended false ceiling which consists of metal frames works with GI bottom protected maintee and cross tee making grids of size 600 x 600 mm with support of J butterfly hooks with GI 10 SWG / 5 mm thick wire including laying of Gypsum ceiling tiles made of M/s Gypsum India limited 595 mm x 595 mm x 8 mm thick the work including two coats of top coats.

Applying water proofing coating black of ceiling tiles made of M/s Gypsum Ltd make for ceiling.

Providing and fixing Gypsum board carnice of 4 inch width in ceiling edges for elegant finish.

Providing and fixing on wall face C.I. rain water pipe including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1 : 2 ( 1 cement : 2 fine sand). c) 150 mm diameter pipe

Providing and fixing M.S. Holder bat clamps of approved design of C.I. or S.C.I. pipes embedded in and including cement concrete block 10 cm x 10 cm x 10 cm of 1 : 2 : 4 mix (1 cement : 2 coarse sand: 4 stone aggregate 20mm nominal size) including cost of cutting holes and making good the wall etc. c) 150 mm diameter

Providing and fixing on wall face C.I. accessories for rain water pipes including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1 : 2 ( 1 cement: 2 fine sand). (A) CI Plain bend c) 150 mm diameter

(C) CI Plain shoes : c) 150 mm diameter

(SH: VIII Finishing)

12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).

Neat Cement punning

Providing and applying wall putty of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade.

Applying one coat of cement primer of approved brand and manufacture on wall surface.

Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade.

(SH: IX Water Supply)

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work) a) 15 mm nominal bore

c) 25 mm nominal bore

e) 40 mm nominal bore

Providing and fixing Two way bib tap of approved quality a) 15 mm nominal bore

Providing and fixing wall brass stop cock of approved quality. a) 15 mm nominal bore

c) 25 mm nominal bore

e) 40 mm nominal bore

Providing and fixing PVC connection pipe with brass union. a) 15 mm nominal bore

Providing and fixing CP brass shower rose with 15 mm or 20 mm dia inlet. b) 150 mm dia

Providing and fixing CP brass (for shower)hot and cold mixer for shower, single lever , exposed , with necessary joints, wall flange etc comple

Providing and fixing DG Vertical storage water heater (Geyser) including fittings comple.

Providing and fixing Water Pump including fittings comple.

(SH: X Sanitary Installation)

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required. a) Long Pan patten WC Pan

Providing and fixing 100 mm sand cast iron grating for gulley, floors or nahni trap.

Providing and fixing sand cast iron heel rest sanitary bend. a) 100 mm dia

Providing and fixing sand cast iron single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. a) 100x100x100 mm dia

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes. a) 100 mm dia

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required. a) Flat back wash basin size 550x400 mm with a pair of 15 mm CP brass pillar taps of heavy quality.

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.

Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.

(SH: XI Drainage)

Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 fine sand) including shuttering complete.

Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement : 5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design. a) Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg), cement concrete 1 : 4 : 8.

Construction of soak pit 1.2 x 1.1 x 1.2 m filled with brick bats including SW drain pipe 100 mm dia and 1.20 m long complete as per standard design.

Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. b) 150 mm dia SW pipes

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design. b) 150 mm dia SW pipes

Providing and fixing UPVC SWR Type B ( As per IS 13592) soil, waste and vent pipes along with all necessary fittings and supports c) 75 mm dia NB

d) 100 mm dia NB

(SH: XII Miscellaneous)

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

Providing and fixing 40 mm dia GI Pipe outlet in cement mortar 1 : 3 (1 cement : 3 fine sand) including cutting and making good the wall.

Providing and fixing Steel railing with necessary fittings.

Supplying and providing water pump set with Engine 1.5 HP with all accessories, fitting and installation etc complete.

Supplying and providing Sintex water tank with all accessories, fitting and installation etc complete.

(SH: XIII RCC. Retaining Wall)

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : a) M20 (1 cement : 1.5 corase sand : 3 stone aggregate 20 mm nominal size

Reinforced cement concrete in retaining wall (any thickness) including attached pillasters, buttresses, plinth and string courses, fillets etc from top of foundation up to floor two level excluding cost of centring,shuttering and reinforcement in : b) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement of RCC work including bending, binding and placing in position complete. A) Tar/ TMT steel

Centring and shuttering including strutting, propping etc and removal of form work for : a) Foundation, footings, bases of columns etc. and mass concrete.

e) Walls including attached buttresses, pilasters etc.

Providing 75 mm dia weep holes including supplying and fixing 75 mm dia. AC Pipes in weep holes as directed by Engineer-in-Charge.

Stone filling behind the wall with hard stone as per the direction of the Engineer-in- Charge.

(SH: XIV Bore Well)

Drilling of 6" dia bore hole & fitting of 5" dia M/S pipe bore hole from top to bottom & developmented bore hole complete.

1.5 HP Submersible pump

Panel board 2 HP

Submersible Cable (2.5mm)

Colom Pipe (PVC)

Safety wire

Bore cap, bore clamp band, adoptor, nipal and R. socket etc.

Fitting charge submersible pump

(SH: XV Furniture)

Brown Wooden Oval Shaped Conference Table with Seating Capacity: 48 Seater

Chair Classic (CH-7B) Godrej

TECHBLAZE USB Computer Microphone On/Off Button PC Microphone Plug & Play Home Studio Microphone for Meeting, Conference, Recording, Podcast, Gaming, Zoom Calling.

Table T-104 ( Godrej)

Belazo Nexa Plastic Chair (Neel Kamal)

OFM Essentials Collection Bonded Leather Executive Chair with Sled Base (Black, ESS-9015)

Epson EH-TW750 3400 lumens 1920 x 1080 Resolution Home Theatre Projector (HDMI, VGA, Miracast) (White)

Inlight Imported Motorised Home Theatre Projector Screen, 9 Feet x 5 Feet, 120 inches Diag. in 16:9 Format, Supports 1080 P - UHD - 3D - 4K Ready Technology, with Cordless Remote

Sony SA-D40 4.1 Channel Multimedia Speaker System with Bluetooth

BLUEWUD Sydney Engineered Wood Square Shape Centre Table with Storage (Wenge)

Kreation Ward Robe ( Godrej two Door)

Chocolate Premium Dressing Table with Stool

Almirah ( Godrej) (Big)

Aristocrat Sofa Set ( 3+1+1) Godrej

CRESENT Dining Table 8 seater with Glass top (Godrej)

CRESENT Dining Table 6 seater with Glass top (Godrej)

CRESENT Dining Chair (Godrej)

(SH: XVI D.G. Set) SH : I : Earth Work

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

SH : II : CC Work

Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Reinforcement of RCC work including bending, binding and placing in position complete. b) Tar/TMT Steel.

Providing and laying cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) excluding the cost of centring and shuttering in : a) Foundation and plinth

Providing and laying damp proof course 25 mm thick with cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for : a) Foundation and plinth

e) Column, pillars, posts and struts etc.

SH : III : Wood Work

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position.

Providing and fixing, fly proof galvanized MS wire gauge of IS gauge designation 85 g with wire of dia 0.56 mm to windows and clerestory windows including 62 x 19 mm beading of best available local wood.

SH : IV : Roof Work

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling. a) Best local approved quality wood.

Providing corrugated Dyna sheet (Tata Brand) roofing fixed with appropriate Steenless steel screw with machine driver & as per the specification of manufacturer complete,excluding the cost of purlines, rafter & trusses. a) 0.45 mm thick Dyna sheet.

SH : V : Flooring

25 mm thick cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) finished with a floating coat of neat cement.

SH : VI : Finishing

12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting (one or more coats) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on old work to give an even shade.

Providing and fixing MS tower bolts (barrel type) with necessary screws etc complete. a) 250 x 10 mm

DG Set with inverter

(SH: XVII Fire Fighting)

Providing & supplying of portable fire fighting equipments of standard quality as per the specification and as per the direction of Engineer-in-charge: a) ABC Type Fire Extinguisher Capacity 9kg (ISI Marked )5 year warranty for extinguisher body and 1 year warranty for extinguisher pressure With testing Certificate (MAKE :- ULTRAFIRE)

Providing & supplying of portable fire fighting equipments of standard quality as per the specification and as per the direction of Engineer-in-charge: b) CO2 Type Fire Extinguisher Capacity 4.5kg (ISI Marked )5 year warranty for extinguisher body and 1 year warranty for extinguisher pressure With testing Certificate (MAKE :- ULTRAFIRE)

c) Add for carriage of materials from Ghaziabad to Kamba

Ms. Barapani enterprises (BID ID -6403)