Supply, Installation, Testing, and Commissioning of 16 meter and 12.5 meter High Mast towers at IIM Udaipur.

Amount

Supplying of following size aluminium armoured cable.3.5 c x 25 sq mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Upto 25 sqmm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface.Upto 35 sq. mm (25 sq mm cable clamped with 1mm thick saddle)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 25 sq. mm (28 mm)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.63 mm dia (OD-63 mm & ID-51 mm nominal)

Cutting road and making good the same including supply of extra quantities of materials i.e. aggregate, moorum screening, red bajri and labour required.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 200 m and lift upto 1.5 m, as directed by Estate Officer.Hard rock (blasting prohibited)

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 100 m :Pipes, cables etc, not exceeding 80 mm dia.

Supply, installation, testing, and commissioning of following LED light confirming the IS 10322 Operating Voltage Range 140-270 V, Operating Temp. range -10°C to +50°C, Rated Voltage 220-240V/AC, 50Hz, System Wattage 250W ± 10%, Rated Current <1.15 Amp, Power Factor >0.95, THD <10%, Driver Efficiency >85%. LED High Power, Beam Angle 60°, Product Lumen Output ≥ 16500 lm, Efficacy ≥ 110 lm/W, CRI > 70 Ra, CCT 5700 ± 355 K (As per ANSI), Housing Aluminum Die Cast with Powder Coating, Optics Lens with Toughened Glass, Mounting Pole/Surface, Cradle Rotation (Degree) 360° Rotation, (tol. ±5 mm). Ingress Protection (IP) IP66, Impact Protection (IK) IK07, Surge Protection 5.0 KV (External Surge Protection 10KV), Over Voltage Protection Cut off @ 300 V/AC ± 5% and Withstand unto 440 V AC for 2 Hrs., with Open Circuit Protection & Short Circuit Protection etc complete as required.200 Watt LED Light

Supply, installation, testing, and commissioning of following LED light confirming the IS 10322 Operating Voltage Range 140-270 V, Operating Temp. range -10°C to +50°C, Rated Voltage 220-240V/AC, 50Hz, System Wattage 250W ± 10%, Rated Current <1.15 Amp, Power Factor >0.95, THD <10%, Driver Efficiency >85%. LED High Power, Beam Angle 60°, Product Lumen Output ≥ 16500 lm, Efficacy ≥ 110 lm/W, CRI > 70 Ra, CCT 5700 ± 355 K (As per ANSI), Housing Aluminum Die Cast with Powder Coating, Optics Lens with Toughened Glass, Mounting Pole/Surface, Cradle Rotation (Degree) 360° Rotation, (tol. ±5 mm). Ingress Protection (IP) IP66, Impact Protection (IK) IK07, Surge Protection 5.0 KV (External Surge Protection 10KV), Over Voltage Protection Cut off @ 300 V/AC ± 5% and Withstand unto 440 V AC for 2 Hrs., with Open Circuit Protection & Short Circuit Protection etc complete as required.300 Watt LED Light

Supply, erection, installation, testing and commissioning of 16 mts High mast Tower of Polygonal Shape for asymmetric loading of up to eight luminaries for Wind Speed up to 180 Km/hr. The Mast shall be made from steel grade of BSEN 10025 and should be in two sections with the bottom section shall be of 4 mm thick and top section of 3 mm thick. Both the sections should be joined by telescopic slip joint. The bottom dia should be of 410 mm or more while top dia should of 150 mm. The bottom section should have Anti Vandalism locking type door size of 1200 mm x 250mm .The mast section should be fabricated for metal protection through hot dip galvanization and thickness of galvanization should not be less than 86 microns. The mast should be supplied with Components including a Head Frame & Pulley Assembly, Winch Bracket, Lantern Carriage Ring for Luminaries and C.G Box Mtg. Arms, Resting Bracket Guide Ring, compensating Disc, Lightening Arrestor, Twin type LED AOL, Wire Rope, Safety Wire Rope, D Suckle Clamps, nuts and Bolts, internal Cable, foundation Accessories., winch assembly with two drums with SWL 750 KG and internal power tool of 2 HP with control panel, manual handle, junction box, Wiring from Junction Box to individual luminaire & MCB in base compartment. The size of base plate diameter should be of 570 mm or more with thickness should be of 25 mm. As per Technical specification mentioned in the tender document.

Supply, erection, installation, testing and commissioning of 12.5 mts High mast Tower of Polygonal Shape for asymmetric loading of up to eight luminaries for Wind Speed up to 180 Km/hr. The Mast shall be made from steel grade of BSEN 10025 and should be in two sections with the bottom and top section shall be of 3 mm thick. Both the sections should be joined by telescopic slip joint. The bottom dia should be of 360 mm or more while top dia should of 150 mm. The bottom section should have Anti Vandalism locking type door size of 1050 mm x 225 mm .The mast section should be fabricated for metal protection through hot dip galvanization and thickness of galvanization should not be less than 86 microns. The mast should be supplied with Components including a Head Frame & Pulley Assembly, Winch Bracket, Lantern Carriage Ring for Luminaries and C.G Box Mtg. Arms, Resting Bracket Guide Ring, compensating Disc, Lightening Arrestor, LED AOL, Wire Rope, Safety Wire Rope, D Suckle Clamps, nuts and Bolts, internal Cable, foundation Accessories., winch assembly with two drums with SWL 350 KG and internal power tool of 1 HP with control panel, manual handle, junction box, Wiring from Junction Box to individual luminaire & MCB in base compartment. The size of base plate diameter should be of 520 mm or more with thickness should be of 25 mm. As per Technical specification mentioned in the tender document.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/ Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the Estate Officer; for the following grades of concrete.Concrete of M25 grade with minimum cement content of 330 kg /cum

Centering and shuttering including strutting, propping etc. and removal of form work for :Foundations, footings, bases for columns

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer and paint of approved color including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing TMT bars in Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete as per specification & direction of Estate Officer.

Supply and installation of outdoor stand mounted, powder coated feeder pillar with 32A TPN MCB incomer, single dial time switch, 25A TP contactor for the automatic switching of luminaries, power tool control with 2 no 9A contactors and raise lower push button, phase indicating lamp and 6 nos of 6-32 amp MCB with Incoming 25 sq. mm and out going 16 & 2.5 sq. mm terminals all complete as per specification including suitable foundation, primer and painting, lock and key provision etc as required & direction of Estate Officer.

Earthing with G.I earth plate 600 mm X 600 mm X 3 mmthick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

R S ELECTRICAL

OLIVE EXPORTS PVT.LTD.