SPL REPAIR TO SIGNAL CENTRE AND W/MAN SHOP AND DRESS IRONING ROOM OF 50(I) PARA BDE SIG COY UNDER GE(WEST) AGRA

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced) in any description and in any position not otherwise specifically provided for omplete all as specified and directed by Engr-in-Charge

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work omplete all as specified and directed by Engr-in-Charge

Dismantling brick tiles in roof top laid bedded & pointed in any mortar and removing from site omplete all as specified and directed by Engr-in-Charge

Demolition of mud any thickness, including plastering and leaping and tiling of whether part removal or full or omplete all as specified and directed by Engr-in-Charge

Disposal of removed/demolished soil/materials exc 1.50 km but n. exc 5 km and depositing where directed omplete all as specified and directed by Engr-in-Charge

M&L cement concrete type B-0, 1:2:4 mix ( 12.5 mm graded agg) in, padding, roof kerbs or mud stops, rounded or chamfered on edges and similar work omplete all as specified and directed by Engr-in-Charge

M&L for Cement concrete 1:2:4 type B-1 ( using 20mm graded crushed stone aggregate) as in floor etc and similar work omplete all as specified and directed by Engr-in-Charge

M&L RCC Type B0 1:2:4 Type using (12.5mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and omplete all as specified and directed by Engr-in-Charge.

PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection ( 75 mm thick ) laying in alternate ways finished even and smooth without using extra cement plinth protection shall be laid to alternate bay system each bay shall exceed 3m in lentgth 12mm wide and 75mm deep joint sall be filed with hot blown bitumen 85/25 and sand omplete all as specified and directed by Engr-in-Charge.

M&L Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) omplete all as specified and directed by Engr-in-Charge.

M & L preparation of newly plastered surfaces of roof including cleaning the surfaces by using wire brush/ pressure hose and applying high performance polyurethene liquid membrane waterproofing coating cold applied in two coats @ 1.5kg/Sqm/2coats spray/brush applied, with an elongation of 300% to 700% and tensile strength of not less than 3N/Sqmm as per ASTM D412 and ASTM C2370, crack bridging ability of 3.5mm as per ASTM C1305, shore a hardness of not less than 60 as per ASTM D2240. The item includes applying epoxy primer @ 0.15Kg/Sqm and a geotextile of 40 GSM to be applied over first coat while first coat is still wet complete as per manufacturer's instructions complete all as specified and directed. Note:- 1. The contractor shall submit a garantee of 10 year from the date of completion of work for waterproofing treatment alongwith manufactures's garantee. The amount of Rs 40 ( Forty) per sqm and min of Rs. 4000/- for waterproofing treatment shall be withheld from contractor's final bill till the expiry of gurantee period. The contractor at his own option may furnish fix deposit receipt pledged in favour of GE(W) Agra against gaurantee money. 2. The water proofing shall be carried out by authorised applicator of manufacturer. The name of applicator shall be got approved from GE before commencement of work.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar ficings, dressed stone work and pre-cast concrete articles omplete all as specified and directed by Engr-in-Charge

M&L for brick work with sub class ‘B’ bricks old size, straight or curved on plan exc 6 M mean radius, built in CM 1:6 omplete all as specified and directed by Engr-in-Charge

M&L for brick work with sub class ‘B’ bricks old size, straight or curved on plan exc 6 M mean radius, built in CM 1:6 omplete all as specified and directed by Engr-in-Charge. Note:- Bricks obtained from item No 12 shall be reused after cleaning.

Brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in CM 1:4 omplete all as specified and directed by Engr-in-Charge

Taking down cement or cement lime plaster of any discription on brick or stone walls/ ceilings etc, including raking out joints, hacking for key, scrubbing down with water etc omplete all as specified and directed by Engr-in-Charge

M & L Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying ement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings .complete all as specified (Payment for providing grooves shall be made separately).

Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge

M&L for 15mm thick rendering in CM 1:6 on any faces of brick or concrete surfaces of walls & finishing the surface even and fair without using extra cement omplete all as specified and directed by Engr-in-Charge

M&L for 15mm thick rendering in CM 1:4 on brick or concrete surface with water proofing compound finished other than fair omplete all as specified and directed by Engr-in-Charge. Note : Water proofing compound will be measured and paid seperately under respective item of Sch ‘A’.

Supply only liquid water proofing compound omplete all as specified and directed by Engr-in-Charge.

M & L for rendering 10mm thick in CM 1:4 on ceiling surface finished even and smooth without using extra cement omplete all as specified and directed by Engr-in-Charge.

M&L Preparing newly plastered or un plastered surfaces of wall and applying two coats of oil bound distemper with roller application over a coat of primer over a coat of average 1mm thick wall care putty on new plastered surfaces omplete all as specified and directed by Engr-in-Charge.

M&L for applying two coats of oil bound distemper with roller on old decorated wall surfaces over 1 mm thick white putty including complete removal of existing treatment with mechanical omplete all as specified and directed by Engr-in-Charge

M & L for applying 1mm thick water proofing putty and two coats of Acrylic weather proof Exterior paint on new plastered or unplastered surface of walls or concrete including preparation of surfaces at any height (not exc11 Mtr) including necessary scaffolding/centering etc omplete all as specified and directed by Engr-in-Charge

M&L for applying three coats of white wash on ceiling new plaster surface with mechanical, omplete all as specified and directed by Engr-in-Charge.

M&L for applying two coats of white wash on ceiling including complete removal of existing treatment with mechanical complete, omplete all as specified and directed by Engr-in-Charge.

Providing Acrylic plastic number plate of size 300mmX 300mm X 3mm and writing building No. of height 10 to 15 cm in any style (bold/italic) and fixed to wall with screws omplete all as specified and directed by Engr-in-Charge.

Providing Acrylic plastic number plate of size 200mmX 200mm X 3mm and writing Qtr No. of height 10 to 15 cm in any style (bold/italic) and fixed to wall with screws omplete all as specified and directed by Engr-in-Charge.

Cutting the roots of trees from the brick walls/stone wall made in cm exc half and not exc one brick thick and making good the disturbed surfaces including coating of paving hot bitumen to arrest further growth to the roots including repair existing surfaces with cm 1:3 or PCC 1:2:4omplete all as specified and directed by Engr-in-Charge.

S&F mild steel joist channel angle or tee sections fixed independently with out connecting plates etc of grade Fe-410-W (Gde E-250 quality B) omplete all as specified and directed by Engr-in-Charge..

S&F 5.0 cm thick sand stone slabs in sun shades, chajjas, shelves, roof slabs etc n.exc. 2m in length punched dressed on face and along exposed edges, self faced on other side and set and pointed in CM 1:4 omplete all as specified and directed by Engr-in-Charge.

M&L One coat of epoxy resin (FAIR BOND EP) on old concrete surface @ 0.30 kg/Sqm including preparation of surface as per as per manufacturer's instruction and applying 25 mm thick on ceiling, beams, chajjas & facia surface etc (average thickness) of cement and sand (fine grit) in ratio 1:4 mixed with chloride free sprey concrete plasticiser (spray crete) as per manufacturer's instruction with guniting machine of pressure capacity not less than 5kg per Sqm and finished the surface even & smooth in CM 1:4 plaster min. 10 mm thick omplete all as specified and directed by Engr-in-Charge

S&F galvanised welded steel wire fabric as extra reionforcement to RCC members like ceilings, chajja’s, beams, columns parapet walls, waste slab etc including all cutting and waste (wt not exc 4.00 kg/Sqm) complete all as specified and directed by Engr-in-Charge.

M&L for treatment of soil under existing floors using emulsion @ one litre per litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors omplete all as specified and directed by Engr-in-Charge

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) omplete all as specified and directed by Engr-in-Charge.

M&L for coloured glazed ceramic tiles in vertical surface 350 x 250 x 7 mm / 450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match tiles including 10mm thick rendering in CM 1:4 on brick wall omplete all as specified and directed by Engr-in-Charge .

M&L vertified ceramic tiles 10 mm thick (square/rectangular) area of each tile exceeding not exc. 0.36Sqm as in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 10mm thick rendering in CM (1:4) omplete all as specified and directed by Engr-in-Charge.(toilet,bath,kitchen, passage floor)

M&L vertified ceramic tiles 10 mm thick (square/rectangular) area of each tile exceeding not exc. 0.36Sqm as in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 10mm thick rendering in CM (1:4) omplete all as specified and directed by Engr-in-Charge.(toilet,bath,kitchen, passage floor)

M&L non skid joint free coloured tiles (1st quality/ premium quality) 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exc. 0.18 Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed or bedding layer of cment mortar (1:6) complete all as specified and directed by Engr-in-Charge.(toilet,bath,kitchen, passage floor)

M&L 25 mm thick PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in sub base of flooring finished even and fair without using extra cement omplete all as specified and directed by Engr-in-Charge.

M&L 18/20mm thick black granite (of any type) work (table rubbed and polished) in steps jambs, pillars, window cills, cooking plateforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of stone including rounding and moulding of edge and making hole for cooking gas pipe omplete all as specified and directed by Engr-in-Charge.

S & F in repairs 15 mm bore chromium plated fancy bib taps long body, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule omplete all as specified and directed by Engr-in-Charge.

S&F in repair 15 mm bore CP Stop valve / angle valve screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed omplete all as specified and directed by Engr-in-Charge.

S&F 15 mm bore CP pillar tap for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified & directed.

S & F in repair tubular towel rail 60 cm length of stainless steel 20 mm Dia with brackets type fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and directed by Engr-in-Charge.

S & F in repair health faucet with 15mm dia 1 mtr long flexible tube and wall hook chromium plated omplete all as specified and directed by Engr-in-Charge.

S&F in repairs 10 ltrs capacity PVC flushing cistern low level (white) with inlet ball valve and handle including flush pipe, brackets, rubber bush, washers etc omplete all as specified and directed by Engr-in-Charge.

S&F in repair vitreous china wash down water closet pan (Pedestal pattern), white with 'P' or 'S' trap incl seat and cover (excluding fluxing cistern and flush pipe) omplete all as specified and directed by Engr-in-Charge.

S&F in repairs Vitreous china wash basin white with pedestal flat back size 550 x 400mm incl waste pipe chain plug bracketsomplete all as specified and directed by Engr-in-Charge.

S&F in repair 100 mm square Stainless steel grating with openable flap omplete all as specified and directed by Engr-in-Charge.

S&F in repair PVC connection 15mm size with PTMT nuts, 600 mm long coomplete all as specified and directed by Engr-in-Charge

S&F Waste coupling of CP (half or full threaded) of 32mm bore suitable for wash hand basin omplete all as specified and directed by Engr-in-Charge.

S&F 32 mm dia PVC waste pipe for wash basin omplete all as specified and directed by Engr-in-Charge.

S&F in repair 500 ltrs capacity rotational moulded polyethylene water storage tank tripal layered, ISI engraved (cylindrical vertical with closed top) hoisted and fixed in position omplete all as specified and directed by Engr-in-Charge

S&F 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20 mm dia (minimum weight - 210 gm) complete all as specified and directed by Engr-in-Charge.

Taking up or down 15mm bore steel tubing and connection omplete all as specified and directed by Engr-in-Charge.

All as per item No above but 20mm bore complete all as specified and directed by Engr-in-Charge

S & F 20 mm outer diameter of CPVC pipes SDR 11 & Plain CPVC SDR 11 including complete fittings on walls/ceiling or laying in floors complete all as specified and directed by Engr-in-Charge.

S&F 20mm bore GI tubes medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed by Engr-in-Charge

S & F in repair 20mm dia Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe complete all as specified and directed by Engr-in-Charged.

S & F 20mm male Brass Threaded Adaptor (MTA/ MBTA) ) pipes any location complete all as specified and directed by Engr-in-Charge.

S & F 20mm female Brass Threaded Adaptor (FTA/ FBTA) ) pipes any location complete all as specified and directed by Engr-in-Charge

S & F in repair 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints and suitable clamp fixed to wall complete all as specified and directed by Engr-in-Charge.

S & F 75 mm bore PVC (SWR) bends sith complete fittings of any radius complete all as specified and directed by Engr-in-Charge.

S & F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall complete all as specified and directed by Engr-in-Charge.

S & F 110 mm bore PVC (SWR) bends with complete fittings of any radius complete all as specified and directed by Engr-in-Charge.

S&F 110 mm bore PVC (SWR) single T with access door of any radius complete all as specified and directed by Engr-in-Charge.

S & F 110 mm bore PVC (SWR) cowl of any radius complete all as specified and directed by Engr-in-Charge.

S & F in repairs 100mm dia of cast iron floor trap, plain with grating incl jointing with solvent cement concrete type B-1 (1:2:4complete all as specified and directed complete all as specified and directed by Engr-in-Charge.

S & F in repair stainless steel curtain rods or 25mm dia as in doors/windows SS brackets fancy type including screws and other necessary fitting (Knob) for fixing brackets SS funnels for 25mm dia dropry rod fixed at each end of rods complete all as specified and directed by Engr-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified and directed by Engr-in-Charge

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 Sqm but not exc 4 sqm each complete all as specified and directed by Engr-in-Charge

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45X85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madeetc complete all as specified and directed by Engr-in-Charge.

M&L for Factory made WPC (Wood Polymer Composite) Double Rebated frame of solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madeetc complete all as specified and directed by Engr-in-Charge.

S&F 35 mm thick Factory made solid panel PVC wire gauzed door shutter 35 mm thick i.e. panel will be of wire gauze of wood grain printed PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC sheet used instead of plain colour PVC sheet & 5mm thick x 15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm used beading of exposed portion of PVC sheet beading channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing including fixing with 100mm long stainless steel butt hinges -04 Nos complete all as specified and directed by Engr-in-Charge

S&F for factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and including fixing with 100mm long stainless steel butt hinges -04Nos with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed by Engr-in-Charge

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC , ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for to rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed to getter with solvent cement, supplying & fixing in the frame at site as per specification & drawing for Item No. 08080 on page No 174 of SSR 2020 (Part-II)

S & F Solid PVC door frame for PVC doors, Kitchen cabinet of size 50mm x 47mm made out of 5mm PVC sheet reinforced with MS square tube, as shown on drawings as per manufacturers specification complete all as specified and directed by Engr-in-Charge.

S & F PVC door( back side) stopper 75mm long complete all as specified and directed by Engr-in-Charge.

S&F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed by Engr-in-Charge.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed by Engr-in-Charge

S&F 150 mm long aluminium alloy handles, cast type, anodised complete all as specified and directed by Engr-in-Charge

S&F Floor door stopper 150 mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed by Engr-in-Charge

S&F 100 mm long stainless steel hinges type B-12 complete all as specified and directed by Engr-in-Charge.

S & F Mild steel Angles, bars, flats etc., as in supports for stiffening of fencing, wall ties, hold fasts, clamps, plain angle cleats for securing purlins and similar small articles confirming to Fe 290 complete all as specified and directed by Engr-in-Charge

M&L cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in bed blocks for fixing hold fasts etc. complete all as specified and directed by Engr-in-Charge

Eco-4000 Series windows fabricated from roll formed sections made of Galvanized steel colour coated/powder coated (Base steel as per IS 513"D" quality, galvanized as per IS 277 with finc of 120 gms/ sqm) with total coated thickness of 0.60mm. Sections shoulld be with primer coat of epoxy primer of 5-7 microns, or powder coated with pure polyester powder up to 50-60 microns thick. Section for frame should be of 72mmx50mm, section for mullion should be of 72mm x50mm, section for shutter frame should be of 47mmx20mm, section for fixed glass bead shoulld be of 12mmx12mm and section for fly mesh shoulld be of 40mmx20mm. Each glazed shutter and mesh shutter shoulld be provided with SS pivot hinges-1 set sec color handle and stay. Each glazed shutter and fixed glass portions should be provided with a glass of 5mm plain float glass. Mesh shutter should be provided with stainless steel 32 guage fly mesh of 304 grade with 144 holes per sq.In. Window should be provided with grill made of 10mm sq MS bars welded to at 150mm centre to centre, 6mm x 12mm MS flat. Total grill unit should be powder coated and fixed to window frame with screws.

Eco-4000 Series Ventilator fabricated from roll formed sections made of Galvanized steel colour coated/powder coated (Base steel as per IS 513"D" quality, galvanized as per IS 277 with finc of 120 gms/ sqm) with total coated thickness of 0.60mm. Sections shoulld be with primer coat of epoxy primer of 5-7 microns, or powder coated with pure polyester powder up to 50-60 microns thick. Section for frame should be of 72mmx50mm, section for mullion should be of 72mm x50mm, section for shutter frame should be of 47mmx20mm, section for fixed glass bead shoulld be of 12mmx12mm and section for fly mesh shoulld be of 40mmx20mm. Each glazed shutter and mesh shutter shoulld be provided with SS pivot hinges-1 set sec color handle and stay. Each glazed shutter and fixed glass portions should be provided with a glass of 5mm frosted glass. Mesh shutter should be provided with stainless steel 32 guage fly mesh of 304 grade with 144 holes per sq.In. Window should be provided with grill made of 10mm sq MS bars welded to at 100mm centre to centre, 6mm x 12mm MS flat. Total grill unit should be powder coated and fixed to window frame with screws.

M & L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10 cm width or girth, not otherwise described complete all as specified and directed by Engr-in-Charge

M & L for applying one coat of synthetic enamel paint including preparation of old Iron surface of any discription not otherwise discribed over 10 cm width or girth, complete all as specified and directed by Engr-in-Charge

Dismantling of wall and ceiling boards (fibere, pulp, insulation boards/slabs/blankets, any thickness. Including cover fillets complete all as specified and directed by Engr-in-Charge

S & F for powder coated aluminium anodised snap grid of size 605mm x 605mm size to support the boars, tiles with powder coated aluminium tee section 35mm x 25mm x 1.40mm, cross tee 23.50mm x 23.50mm x 1.40mm and powder coated aluminium angle 25mm x 25mm x 1.40mm as on edge/sides including proper hanging arrangement with 4mm dia nodized galvnised iron wire and adjuster incouding 4mm tick Everest Non Asbestos fiber cement designer pre laminated board (E-Board classic) size 60cm x 60cm fixed on ceiling on staples of snap grid and including making good the distrubed wall portion with CM 1:3 or with PCC, 1:2:4 type B1 ( using 20mm graded stone aggregates ) as required complete all as specified and directed by Engr-in-Charge

Dismantling of Asbestos cement ( corrugated, semicorrugated, etc.) sheets in roof coverings.complete all as specified and directed by Engr-in-Charge

S & F Pre- painted galvalume aluminum zink coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering/cladeding to wall, fixed with self tapping screw complete all as specified and directed by Engr-in-Charge

Dismantling timber scantling 40sq. Cm and over in section , in any position complete all as specified and directed by Engr-in-Charge.

S & F Roof trusses Fe 410-W (Gde-E-250) quality-A (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing ( Beam, Tee, angles, channel or flat sections) including distance pieces, ceats etc complete all as specified and directed by Engr-in-Charge.

S & F for powder coated aluminium frame for door, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engr-in-Charge

S & F for powder coated aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, aluminium snap beading screws etc. complete all as specified and directed by Engr-in-Charge. (Note: Sheet glass and veneered board will measured and paid separatly)

S&F automatic floor mounted hydraulic door closer, heavy duty with pivot, aluminium body, ISI marked, complete all as specified and directed by Engr-in-Charge

S&F 5.50 mm thick ordinary quality sheet glass with necessary jointing cleats, glazing clips, rubber packing & anodised aluminium snap beading area exc 0.5 sqm in each plane complete all as specified and directed by Engr-in-Charge.

S&F 100 mm long Mortice lock with four levers (vertical type) , aluminium body and fixed complete all as specified and directed by Engr-in-Charge

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings, tube light fittings etc complete and removing all retrieved materials to MES stores for segregation of serviceable /Unserviceable fitting&fixture and also making good disturbed surfaces of wall, floors etc complete all asspecified and as directed by the Engineer-in-Charge.

M & L for concealed point wiring with FRLS PVC insulated unsheathed multistranded copper conductor cables of 1.5 sqmm size alongwith one earth continuity conductor with FRLS PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm size through and included PVC Conduit terminated in 1.6 mm thick mild steel sunken boxes of suitable size with 3 mm thick hylam sheet top cover fixed with suitable size of brass screws for fixing of switches, sockets, fan regulators for one light point or one fan point controlled by one switch including making good to dismantled surfaces with existing finishes complete all as specified and directed by Engr-in-Charge

All as per item No 2 above, but for one 3 pin socket outlet 5 Amp on same board complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 2 above, but for one 3 pin socket outlet 5 Amp on independent board complete all as specified and as directed by the Engineer-in-Charge.

All as per serial item No 2 here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 1.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing switch piano flush button single pole one way 5 Amps complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing socket outlet multipurpose 2 pin and 3 pin, 5 Amp, flush type complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing switch socket combination multi purpose 2 in 1, 3 pin 5 Amp and 15 Amp, flush type complete all as specified and as directed by Engr-in-charge.

Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge.

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp MCB.complete all as specified and as directed by Engr-in-charge

M&L for Concealed Sub main wiring with two runs of single core 2.5 sqmm PVC insulated, unsheathed multistranded copper conductor 1100 volts FRLS cable, including one run of 2.50 Sqmm single core PVC insulated unsheathed multistranded copper conductor 1100 volts FRLS cable as earth continuity conductor drawn through and including one run of PVC condute upto 25mm heavy duty and connected accessories etc.,and connecting to common earth dolly including making good disturbed surface by plastering and two coat of distamper of existing colour complete all as specified and as directed by Engr-in-charge. Note :- Two runs of main cable , one run of earth continuity conductor cable and one run of PVC conduite will be measured as one unit for payment purpose.

M&L for Concealed Sub main wiring with two runs of single core 6.0 sqmm PVC insulated, unsheathed multistranded copper conductor 1100 volts FRLS cable, including one run of 6.0sq.mm single core PVC insulated unsheathed multistranded copper conductor 1100 volts FRLS cable as earth continuity conductor drawn through and including one run of PVC condute upto 25mm heavy duty and connected accessories etc.,and connecting to common earth dolly including making good disturbed surface by plastering and two coat of distamper of existing colour complete all as specified and as directed. Note :- Two runs of main cable , one run of earth continuity conductor cable and one run of PVC conduite will be measured as one unit for payment purpose.

Supply and fixing in repair LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.complete all as specified and as directed by Engr-in-charge

Supply and fixing in repair LED lights fitting 1x 16W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.complete all as specified and as directed by Engr-in-charge

S & F in repair LED light fitting 1x 11WWbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. complete all as specified and as directed by Engr-in-charge

Supply and fixing in repair round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.complete all as specified and as directed by Engr-in-charge

Supply and fixing in repair LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including fixing arrangment at wall/pole all as directed. complete all as specified and as directed by Engr-in-charge

Supply and fixing in repair Distribution board of 08 Way with 200 amps rated bus bar sheet Metal enclosure double door all as directed by Engr-in-Charge.

Supply and fixing in repair Distribution board of 12 Way Triple pole and neutral sheet Metal enclosure double door suitable upto 250 Amps MCCB as incomer all as directed by Engr-in-Charge.

Supply and fixing in Repair MCCB 4 Pole, 415 V, Adjustable type, 250 Amps with breaking capacity 36 KA all as directed.

Supply and fixing in repair MCB SPN 40 to 63 amp rating 240V, 10KA 'C' complete all as specified and as directed by Engr-in-charge

Supply and fixing in repair MCB SP 5 to 32 amp rating 240V, 10KA 'C'.complete all as specified and as directed by Engr-in-charge

Supply and fixing ceiling fans (BLDC) complete with blades, down rods, electronic regulator( suitable for BLDC Fan) and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor.complete all as specified and as directed by Engr-in-charge

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 380mm sweep with, blades, and frame and louvers.complete all as specified and as directed by Engr-in-charge

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the 4 mm GI wire by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 5 of SSR 1991 Part-I and connecting to CBDB’s as specified or indicated including testing on completion .

Taking Down UNSV Cable and Supply and laying XLPE insulated armoured heavy duty electric cable with aluminium conductor (Stranded) 1100V grade cross-sectional area 50 Sqmm 3.5 core laid in trenches or passing through pipe or fixed on pole etc complete all as specified and directed by Engr-in-Charge.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5 m depth for laying of cable/ stay assy/LT poles and getting out in hard/dense soil complete all as specified and as directed by Engr-in-charge.

Returning filling incl spreading watering and well ramming in layers not exceeding 25cm in hard and dense soil complete all as specified and as directed by Engr-in-charge.

Removing excavated material not exceeding 50 mtrs and depositing where directed at a level n. exc 1.5mtr above the starting point complete all as specified and as directed by Engr-in-charge.

Sand cushioning to underground cable complete all as specified in clause 19.75 of SSR Part - I complete all as specified and as directed by Engr-in-charge.

Material and labour for un-reinforced pre-cast concrete cable covers, class LV type-1, flat size 250mm x 150mm x 40mm thick complete all as specified and as directed by Engr-in-charge

Supply and fixing in replacement tube medium grade galvanized with all fitting and fixed complete to walls/ poles/ ceiling or laid in floor of size 40 mm bore for the protection of UG cables including dismantling/ taking out old, unserviceable onecomplete all as specified and as directed by Engr-in-charge

Supply and fix in repair/replacement ON LOAD change over switch 415V in sheet metal enclosures 4 pole of capacity 63 Amps. complete all as specified and as directed by Engr-in-charge

Supply and fix in repair/replacemenON LOAD change over switch 415V in sheet metal enclosures 4 pole of capacity 125 Amps. complete all as specified and as directed by Engr-in-charge

Taking down the split type Air conditioner of any capacity/make from site and deposite the same to AGE E/M store yard for refixing or reuse complete all as specified and as directed by Engr-in-charge.

Transportation of Split type AC from E&M Yard to site and refixing only the split type AC of any make/capacity including servicing of air conditioner and refilling the gas at new/existing place complete all as specified and as directed by Engr-in-charge

R.S BUILDERS (BID ID -3140790)

M/s Kok Singh Sisodia (BID ID -3140488)