Re-configuration of Terminal building at S. V. Airport, Raipur. SH Civil works

Amount

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Brick work with fly ash bricks (Min compressive strength 50 kg / sq cm) above plinth upto floor V level: a) Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with fly ash bricks (Min compressive strength 50 kg / sq cm) above plinth upto floor V level: A) Cement mortar 1:4 (1 cement :4 coarse sand)

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing roofing consist of 0.8 mm thick galvanized steel deck sheet confirming to IS 277:1992 used as permanent shuttering over which MS wire mesh 3mm laid at 100x100 mm grid including edge trim covered with concrete. This metal deck will be supported on structural steel beam with shear studs. (Structural steel like Beam, column, joists etc. & concrete of different grade as per design will be paid separately).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round Soil Waste pipes including bed concrete as per standard design : 100 mm diameter Soil Waste pipe

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-incharge.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Dismantling steel work in single sections including dismembering and stacking within 50 metres lead in: R.S. Joists

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

Extra for dismantling trusses, rafters, purlins etc. of steel work for every additional height of one metre or part thereof beyond 5 metres.

Providing and fixing partition for temporary barricadings upto required height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/ sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. 66 mm overall thickness partition using 8 mm thick Single skin multipurpose cement bonded wood particle board manufactured as per IS: 14276 with suitable cement bonded board screws (Note :- One time payment shall be made for providing barricading from start of work till completion of work i/c shifting. The barricading provided shall remain to be the property of the contractor on completion of the work).

Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured): From brick work in cement mortar

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead : Thickness above 10 mm up to 25 mm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab of all colour and texture except Black, Cherry/Ruby Red

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily Glazed vitrified floor tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm

Providing and laying fixing 18mm thick gang saw cut,mirror polished,premoulded and prepolished, machine cut for kitchen plateforms,vanity counters,window sills,facias and similar locations of required size, approved shade,colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement:4 coarse sand), joints treated with white cement,mixed with matching pigment, epoxy touchups including rubbing, curing, molding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of all colour and texture except Black, Cherry/Ruby Red:Area of slab over 0.50 Sqm

Extra for fixing marble/granite stone, over and above corresponding basic item, in Facia and drops of width up to 150mm with epoxy resin based adhesive, including cleaning etc complete.

Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/granite/stone work, including necessary holes for pillar taps etc including moulding,rubbing and polishing of cut edges etc. complete.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel (ACP) Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and Installation of automatic double sliding door system (model ES 200 Easy 6.25 mtr Full System, Double Sliding – Type B of dormakaba) of approved make . complete in all respect as per direction of Engineer-in-charge.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protectivesurface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. (a) 1.0 mm thick

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. 75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board conforming to IS: 2095: (part I): 2011 (Board with BIS certification marks)

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer in charge (Door handle, lock and stopper etc. to be paid separately)

Supply & installation of Spider Glazing system held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider, Routels, connectors & bolt assembly etc. connected with structure steel vertical pipe as required. The glass panel assembly shall be connected to Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured. (Structure steel shall be paid separately)

Removing of glass 17.52mm thick laminated glass (8mm thick toughened glass + 1.52mm P.V.B. lamination + 8 mm thick toughened clear glass) in existing glazing structures of height upto 3mtr including scafolding and placing at requied location within airport premises all complete as per direction of Engineer-in-charge.

Removing double glazed hermetically sealed glazing in existing glazing system of all heights with 6 mm thick toughened outer glass, having 12 mm air gap, and 6mm thick clear toughned inner glass etc. and placing at requied location within airport premises complete in all respect as per direction of Engineer-in-charge.

Removing of suspended Spider Glazing in existing glazing system of all heights including all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. and placing at requied location within airport premises complete in all respect as per direction of Engineer-in-charge.

Removing float glass of thickness 12mm in existing partition including fitting etc. including racking out the old putty: and placing at requied location within airport premises complete in all respect as per direction of Engineer-in-charge.

Providing and supplying 12 mm thick toughened glass of approved brand and manufacture, including making necessary holes etc. all complete as per direction of Engineer-in-charge.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm

Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately): Flat surfaces

Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately): Curved surfaces

Providing and fixing white vitreous S Trap Tankless Single Piece Water closet (ONS-WHT-10851S300UFSMTL of Jaquar make or equivalent) of size 380X620X450mm with UF soft close slim seat cover,hinges Single flush with Sensor & manual operated, fixing accessories and accessories set etc. complete including cutting and making good the walls and floors wherever required complete as per directions of Engineer incharge.

Providing and fixing white vitreous counter Top Wash Basin (Code FLS-WHT-5601 of Jaquar make or equivalent) of size 570x420x195mm i/c cutting and making good the walls wherever required complete as per directions of Engineer incharge.

Providing and fixing 32mm dia Bottle Trap (Code ALD-769L300X190) of Jaguar or approved equivalent and other ancillary fittings including painting of fittings and brackets, cutting and making good the walls wherever required complete as per directions of enginner incharge.

Providing and fixing Touchless urinal with rear inlet in white 1L with integrated sensor in white (Code Patio Touchless of Kohler make or equivalent) of size 332mmx335mmx642mm etc. complete i/c cutting and making good the walls and floors wherever required complete as per directions of Engineer incharge.

Providing & fixing Sensor faucet (battery operated)(Code SNR-51021of jaguar make or equivalent) for wash basin including all fittings and accessories complete as per directions of Engineer incharge.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not les than 690 gms. 15 mm nominal bore.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board grounf fixed to wooden cleasts with C.P. brass screws and washers complete.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 (a) 15mm nominal bore

Providing and fixing in position Health faucet with hose and bracket in polished chrome (code Elate K-97258I-CP of Kohler or equivalent) etc. complete as per directions of Engineer-in-charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 178 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including allCPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

a) 15 mm dia nominal bore

b) 20 mm dia nominal bore

c) 25 mm dia nominal bore

d) 32 mm dia nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 40 mm nominal dia Pipes

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum)sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Providing & fixing modular toilet cubicles (model Besco cubicle ZMS SS 2100MM of Merino or equivalent), consisting of high proessure 12mm thick compact laminate board as per IS 2046 and as per fire retardent BS-476/96 standard with phenolic core panels for partitions of intermediate divider (1945mm), doors (1925mm x 600mm) and pilasters (the cubicle shall be have dimensions of 1m to 1.25m width with overall height 2.1m (Including bottom gap 100mm , but the panel area required for one cabin shall be one longer and the one shorter side of the cabin including one door) with a door size of minimum 600mm width, the assembly shall be supported by SS grade 304 head rail on top of panels and panels shall fixed on the floor with a clearance of maximum 100mm using SS grade 316 adjustable legs screwed to the floor included assessories with standard SS grade 304 accessories, butt hinges with cover, SS grade 304 top rail , privacy thumb turn i/c occupancy indicator coat hook, door knob, adjustable pedestal, SS grade 304 "U" channel door stopper channel, rubber door stopper lining, SS screws & wall plug etc complete as per manufacturers specification and as directed by Engineer in charge. The rate is inclusive of cost carriage of all materials, labour charge, lead & lift, all taxes etc complete. (L shaped panels matching the two dimensions of a cabin is only required to make one cubicle)

Providing & fixing urinal partitions (model urinal Modesty SS series SS of Merino or equivalent), consisting of high proessure 12mm thick compact laminate board as per IS 2046 and as per fire retardent BS-476/96 standard. urinal partition panel of size 500mm (W) x 1200mm (H) and overall height 1.85m (Including bottom gap 650mm). assembly shall be supported by SS grade 304 accessories, right angle brackets, SS screws & wall plug etc complete as per manufacturers specification and as directed by Engineer in charge. The rate is inclusive of cost carriage of all materials, labour charge, lead & lift, all taxes etc complete.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Sand cast iron S&S as per IS: 3989

Providing and fixing Toilet Roll Holder (Code CAN-1151N) Jaquar make or equivalent as per directions of Engineer-in-Charge.

Providing and fixing brass stop cock of approved quality : 15 mm nominal bore

Providing and fixing Stainless steel soap dispenser, satin finish model no. ES04 of Euronics Industries Pvt.Ltd. or equivalent as per directions of Engineer-in-Charge.

Providing and fixing Pneumatic tank 3/6L with full frame (Instafit Next Gen, K-26353IN-P-NA) Kohler make or equivalent as per directions of Engineer-in-Charge.

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore

Providing and fixing in position Soil Waste PVC pipe and vent or antisyphonage pipes supreme/ Astral/ Finolex make or equivalent as per IS - 13592(working pressure of 6kg/ cm2) including cutting, jointing with approve solvent cement compount as per IS - 14735, wastage etc. complete as per manufacturer's specifications and satisfaction of Engineer-in-charge. 100mm dia

Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 600 mm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge.

Providing and fixing in wall lining medium density fibre board IS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete. (a)12 mm thick.

Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with : Decorative veneer facings of approved manufacture

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in?charge (Frame work shall be paid for separately). (a) 12mm thick commercial ply conforming to IS : 1328 BWR type

Providing and fixing in position floor drain in polished chrome (Complementary K-7275IN-CP of Kohler make or equivalent) etc. complete as per directions of Engineer-in-charge.

Providing and fixing Pneumatic face plate in polished chrome (Graph,K-20189IN-P-CP) Kohler make or equivalent as per directions of Engineer-in-Charge.

Providing and fixing Recessed- stainless Steel Baby Diaper changing station (Model no. EDC4R) of Euronics Industries Pvt.Ltd. make or equivalent as per directions of Engineer-in-Charge.

Providing and fixing Multifunction Recess Panel consisting of Automatic paper dispenser,Hand dryer & Waste Receptacle (KINOX KMR33A of Euronics Industries Pvt.Ltd. make or equivalent) as per directions of Engineer-in-Charge.

Providing and fixing stainless steel ( Grade 304) table of required size & dimension made of Hollow tubes, plates/sheets etc., including welding, grinding, buffing, polishing and makingn curvature (wherever required) i/c fixing with necessary accessories as per direction of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as hinges, fasteners etc.).

Providing and fixing stainless steel ( Grade 304) frame of required size & dimension for frisking enclosure/display boards made of Hollow tubes, plates/sheets etc., including welding, grinding, buffing, polishing and making curvature (wherever required) i/c fixing with necessary accessories as per direction of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as hinges, fasteners etc.).

Providing and fixing in position plain flex of required size with MS square hollow frame (25mmx25mmx1mm) compatible with the brand complete as per direction of Engineer-in-Charge.

MD RIYAJUDDIN