COMPREHENSIVE MAINT TO BLDGS OF GROUP-IV UNITS/ LOC AT LEIMAKHONG MIL STN

Schedule 'A'

Taking down Chowkats or frames with shutters (w/o taking of shutters from the frame) exc. 1.5 Sqm but n.exc. 4 Sqm complete all as specified and as directed.

Taking down Chowkats or frames with shutters (w/o taking of shutters from the frame) area n. exc 1.5 Sqm complete all as specified and as directed.

Taking down shutter of any description and removing frome site exc. 1 Sqm & n. exc. 2 Sqm each leaf complete all as specified and as directed.

Taking down shutter of any description and removing frome site n exc. 1 Sqm each leaf complete all as specified and as directed.

S&F 2nd class hard wood (haldu/ hallock) plain, solid, straight chowkats & frames , wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete.

S&F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, both face is covered with decorative face veneer with lipping/frame to match complete all as specified and as directed.

S &F 2nd Class H.W Glazed and skeleton shutters 35 mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

All as per item No. 7 but in windows, ventilators, etc. are provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24(b) complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube in opening as per specification & drawing

S&F factorymade solid pannel PVC door shutter 30mm thick consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with neat moulded plan colour PVC 'C' channel having a PVC sheet strips of 20mm width stuck in side with solvent cement for styles and plain colour PVC sheets for top rails, lock rail and bottom rail on eithor side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheets to be fitted in the MS frame welded/sealed to the stiles, and rails with suitable PVC sheet bedding and jointed together with solvenet cement, supply and fixing in the frame at site as per specification as specified

S&F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

M and L two coat of synthetic enamel painting to wooden surfaces (frame & shutter) over a coat of primer incl preparation of wooden surface.Surfaces of any description, not otherwise descri-bed, over 10cm width or girth complete all as specified and as directed.

Taking down chowkats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames) and refixing in same opening complete all as specified and directed by Engr-in-Charge.

Taking down chowkats or frames exc. 1.5 sq. m but n exc 4 sqm each with shutters (without taking off shutters from the frames)and refixing in same opening complete all as specified and directed by Engr-in-Charge.

Supply and fix for aluminium powder coated three track sliding window with two glazed shutters, one 4mm thick float glass ordinary quantity and one shutter of stainless steel wire mesh 0.36mm nominal dia of wire & average width of aperture 1.40mm including good quality of bearing handle, locks, PVC rubber lining, rollers etc complete all as specified and as directed. Catlouge numbers of Jindal company or equivalent make as specified. Sections of Jindal company : Three track bottom – 20957, Three track top/vertical – 20958,Handle – 20606, Interlocking – 20605, Top and bottom – 20604 complete all as specified and as directed.

S&F ventiltors/ louvers with parttially guaged shutter using 5 mm thick x 10 cm wide frosted glass strips and following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make and rubber beading etc all as directed.(a) SP :20048 (b) Glazing clips :19352 complete all as specified and as directed.

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/stainless steel screws @ 200mm centre to centre, including cuttting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aliminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge.

S & F aluminium anodised Hasp and staple 75mm , safety type, mild steel hinge pin including bolt to hinge plate and fixed with screws

S&F 100 mm long Aluminium anodised barrel tower bolt of extruded section .

Supply and fix Extruded aluminiumalloy handles,100 mm long fabricated type., anodised

S&F 100 mm long Stainless Steel butt hinges medium weight colld rolld.

S&F 150mm aluminium anodised of extruded section barrel tower bolts.

S&F 200mm aluminium anodised of extruded section barrel tower bolts.

S&F 150mm long alumiunium handles cast type anodised.

S&F 140mm long floor door stopper of brass body and tongue with had drawn steel spring complete all as specified

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolt of extruded section or cast aluminium alloy and fixed 300mm long complete all as specified and directed

S&F in repairs 100 mm long Stainless Stee butt hinges medium weight colld rolld.

S&F in repairs 150 mm long Aluminium anodised barrel tower bolt of extruded section .

Supply and fix in repairs Extruded aluminium alloy handles, 150mm long fabricated type., anodised

S&F in repairs 300 mm long Aluminium allow anodised sliding door bolt with hasp staple (bolt type ) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast alu allow complete all as specified and as directed.

Supply and fix in repairs floor door stopper of aluminium body and tongue anodised with hard drawn steel spring fixed in floor over all length of cover plate 150mm.

S & F in repairs fancy type decorative Drapary rod of 20mm dia for window and doors with curtain rings and decorative doom holders fixed to wall with screw complete.

S&F in Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones

S/F 3 mm thick sheet glass ordinary quality & glazing with oil putty in squares n. exc. 0.5 Sqm in each pane.

S/F figured glass 3 mm thick, pin head type & glazing with oil putty in squares n. exc. 0.5 Sqm in each pane

S&F door closer (aluminium extuded body section) hydreulically regulated, ,designation No 1 universal type, suitable for door shutters up to 700mm in width and of wieght not more than 35Kg complete all as directed.

S&F in repairs vitreous china European type wash down water closet pan (Pedestal pattern) of white colour including plastic water closet seat black closed pattern with flat bottom (with MS or CP hinging device) and fixing bolts, P or S trap, necessary inlet and outlet connections including syphonic action type low level PVC flushing cistern of 10 lit capacity white in colour and PVC flush pipe 32mm dia complete all as specified and directed by Engineer -in- Charge.

Supply and fix in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests Complete all as specified and directed

S&F in repair PVC flushing cistern 10 ltrs capacity ISI marked incl PVC down pipe and connection etc all complete in repairs.

S&F in repairs plastic water closet seat cover black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminum hinging device

Supply only Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern

S&F Vitreous china Wash Hand Basin with pedastal 600mmX 480mm white fixed in repairs including 15 mm pillar cock cast copper alloy CP, 15mm cast copper stop valve, 32 mm brass CP waste fitting & 15 mm PVC connection pipe 450 mm long fixed in repairs

Supply and fix in repairs Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union fixed in repair

S&F in repair for stop cock copper alloy CP screwed down high pressure with crutch or butterfly handle screwed both ends for iron/pipe or for union and fixed 15 mm bore in repairs

S&F in repair bib taps cast copper alloy with crutch or butterfly handle, chromium plated fancy type screwed down, screwed for iron pipe or for brass ferrule and fixed in repairs

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repairs 32/50mm dia PVC waste pipe for kitchen sink , WHB , Urinal etc complete all as specified and as directed.

Supply and fix in repair 15mm bore piller taps of cast copper with capstan head CP screwed down high pressure with or without lettered hot and cold with long screwed shank and fly nut for iron pipe and fixed in repairs

S&F in repair Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed

S&F PVC connections 15 mm size with PTMT nuts to length 450 mm in repairs.

S&F in repair Brass, Chromium plated, Tubular towel rail, 20mm dia, D type, 60cm long between flanges

S&F in repairs Soap dish, any type, fixed to plugs with chromium plated brass screws

Supply and fix in repairs brass Chromium plated shower roses 125mm size with or without swivel joints, any size, including fixing to steel pipe or union

Taking down steel tubing and connections including cleaning for re-fixing or removal to store of 15 mm bore

Taking down steel tubing necessary fittings connection etc for 20 mm bore pipe

S&F GI tubing 15mm dia medium grade galvannised with all fitting &fixed complete to walls & ceiling or laid in floors

S&F 20mm thick GI Tubing medium grade galvanised with all fitting and fixed complete

S&F in repair PVC (SWR) floor trap, plain with grating including jointing with solvent cement dia of outlet in 75mm.

S&F in repairs 110mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors.

S&F in repairs 75mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors.

S&F in repairs 110mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to walls.

S&F in repairs 75mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to walls.

S&F in repairs PVC (SWR) bends of any radius of 110mm dia. With oval and access door

S&F in repairs PVC (SWR) bends of any radius of 75mm dia.

S&F in repairs PVC (SWR) branch piece (single ‘Y’) equal or unequal for 110mm dia PVC pipe.

S&F in repair PVC(SWR) branch piece (single ‘Y’) equal or unequal for 75mm dia PVC pipe.

S&F in repair for PVC (SWR) junction (single ‘T’) with access door for 110mm dia pipe.

S&F in repair for PVC (SWR) junction (single ‘T’) with access door for 75mm dia pipe.

S&F in repair for PVC (SWR) vent cowl suitable for 110mm dia PVC pipe.

S&F in repair for PVC (SWR) vent cowl suitable for 75mm dia PVC pipe.

Supply and fix in repairs ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed in repairs of pipe 20 mm dia.

S/F in repair sinks made of stainless steel of 1 mm thick kitchen sink with plug washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495 x 420 mm bowl size 410 mm x 330 mmx 160 mm

Dismantling Water Tanks & removing from site, capacity of tanks 250 ltr and n exc 500 ltr complete all as specified and as directed.

Dismantling Water Tanks & removing from site, capacity of tanks 500 ltr and n exc 1000 ltr

S/F Rotational moulded polyethelene water storage tanks (cylindrical, vertical with closed top) hoisted & fixed in position all as specified in SSR Pt-I, 500 litre capacity.

S/F Rotational moulded polyethelene water storage tanks (cylindrical, vertical with closed top) hoisted & fixed in position all as specified in SSR Pt-I, exc 1000 ltr capacity

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position, Capacity exc 250 litrs n exc 500 litrs, cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position, Capacity exc 500 litrs n exc1000 litrs and cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets.

S&F for exposed GI powder coated snap grid frame work for false ceiling of grid size 600X600mm comprising of wall /cleat angle of size 24X 38X0.70mm with 4mm dia GI providing 4mm thick 'E' board in ceiling with galvanised iron snap frame of 'T' Section 24x38x0.70mm wall/cleat angle 25x25x0.35mm thick and hanging with 2mm GI wire all fixed arrangement will be done as per manfraxture instruction including two coat of oil bound distemper and one coat of primer complete all as directed by Engr-in- Charge.

S&F 4mm thick ply wood grade BWR (type BB) fixed with nails to the timber frame work as in wall complete all as specified.

M & L for 2nd Class hard wood plain fillets square, rectangular or triangular exc 3.00 & n.exc 6.00 Sq cm in sectionn, clean sawn, se-cured screws complete all as specified.

M & L 18/19 mm thick Mediam density board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber work complete all as specified and as directed.

M&L for Second class hardwood Weather boarding, clean sawn, thickness 20mm to 25 mm and rebated on thick edge to give 20mm laps and fixed complete all as specified

Material and labour for 0.90mm thick decorative laminate type 1 of surface finish, colour, pattern and size as approved, fixed with approved adhesive as per manufacturer’s instructions on horizontal and vertical surfaces etc. complete all as specified and as directed.

Material and labour for 4mm thick one side decorative group match veneer complete all as specified and as directed.

Dismantling of timper scantling 40 sq .cm and over in section,in any position

M&L for second class hard wood in scantling wrought, timber framed & fixed complete all as specified and directed.

Fixing only second class hard wood in scantling clean sawan , timber framed & fixed complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, including one coat shop primer

M & L two coat of synthetic enamel paint on steel surfaces over one coat of zinc primer including preparation of new steel surfaces exceeding 10 cm width or girth

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings ,any description and in any position, all as directed.

M&L for Pre- painted galvalume aluminum zinc coating GI based semi corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr -in- Charge.

S&F Galvanised, corrugated mild steel sheeting pf 0.63mm thickness with two corrugations side lap, fixed with L type or J type or cranked hook bolts, in roofs, walls etc. with grade of zinc coating 275.

S&F galvanized plain mild steel sheeting 0.63 mm thick in ridges, hips, valley gutters, drip & straight flashings (length and firth as fixed ) with grade of zink coating 275

M&L for filleting in any position & to any shape, sectional area exc.25 but n. exc. 50 sqcm. In CM 1:4 including all mitres , stops etc, complete all as specified.

Demolition of brick work or stone/ boulders masonry, built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work and precast concrete articles

M&L for brick work with subclass 'B' brick straight or curved on plan 6m mean radious built in CM (1:6) etc as directed .

M&L brickwork with sub- class ‘B’ bricks, straight or curved on plan to any radius built in cement mortar 1:4 using old size bricks as in half brick thick wall.

Demolition of cement concrete in ground floors and paving not exc 15cm thick (below or above ground level) un-reinforced.

M&L for 75mm thick PCC (1:4:8) type C2 (using 40mm graded aggregate) as in sub base/flooring/ paving complete;

M&L for 75mm thick PCC (1:3:6) type B2 (using 20mm graded aggregate) as in plinth protection/hard standing, finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on stone / Brick walls including raking out joints, hacking for key, scrubbing down with water all as specified

M&L for rendering 10mm thick plaster on fair faces of brick work or concrete surfaces (1:6) finished the surface even and Smooth without extra cement.

M&L for rendering in CM 1:4 with 15mm cement plaster with water proofing compound @ 2% by weight of cement or as per manufacture's instrs having smooth and fair finish all as specified and directed by engineer - in - charge Note :- (1) Use of Dimapur Sand to plaster. (2) WPC pdr shall be measured and paid separately.

Supply only integral water proofing compound

M&L for rendering 5 mm thick plaster on ceiling concrete surfaces as in CM (1:3) finished even & Smooth without using extra cement.

M&L for three coat of white wash to newly plastered surfaces of on ceiling.

M&L for two coats of oil bound distemper over a coat alkali resistent primer to newly plastered surfaces of walls including preparation of surfaces.

M&L for preparing newly plastered surfaces of walls and applying two coats of cement base paint over a alkali resistent primer complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for colored Non Skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or colored cement to match, including 15 mm thick screed bed or bedded layer in cement mortar 1:6 for laying floor finish.

M&L for colored glazed ceramic tiles (300mm x450mm) x 7 mm thick on vertical surfaces set and jointed in neat cement slurry and pointed in white or colored cement to match including 10 mm thick backing coat in cement mortar (1:4) on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing to receive /fixing dado/ skirting tile.

M&L for Non - skid Ceramic colour tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface including 15mm thick screed bed in CM 1:6 etc set and jointed in neat cemet slurry and pointed in white or coloured cement to match as per by Engineer - in Charge.

Dismantling of stone slab in any description or thickness, laid bedded jointed in any morter.

Material and labour for Granite(of any type) 18 to 20 mm thick work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade

Material and labour for bitumen patches on roof sheet to arised the leakage sepage complete all as specified and directed.

Taking down copper/ aluminium point wiring ie. light, fan, socket or power/points complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. and making good disturbed surfaces of ceiling, walls, floors, etc.

M&L for point wiring with two single core 1.5 sqmm (nominal area) FRLSH PVC insulated unsheathed cable, 1100 volts grade multistranded copper conductor cable in and incl PVC casing and capping of suitable size fixed on surface all as directed with using modular PVC boxes including modular frame and white cover plate for mounting modular switches, sockets and fan regulators etc incl all accessories and using one single core 1.5 sqmm (nominal area) FRLSH PVC insulated unsheathed multistranded copper conductor cable, 1100 volts grade as in earth wire connected to common earth dully complete all as specified and directed. Note : (i) The quoted rates shall be deemed to be inclusive for fixing the PVC casing caping to surface. (ii) Fititngs like switches, sockets, regulators, lamp holders, light fittings shall be measured and paid appropriate item of schedule ‘A’

One light point controlled by one, one way switch.

One ceiling/exhaust fan point controlled by one, one way switch

One socket outlet 5 Amps 3 pin on same board with other switch

One socket outlet 5 Amps 3 pin on independent board with cable of 1.5 sqmm size complete all as specified and directed

One bell point controlled by one way switch complete all as specified and directed.

All as per item No.123 here-in-above but with cable size 2.5 Sqmm for one 3 pin, 15 Amps socket outlet on independent board and multistrand PVC insulated copper earth continuity conductor of size 2.5 Sqmm complete all as specified and directed.

All as per item No.123 here-in-above but with cable size 4 Sqmm for one 3 pin, 15 Amps socket outlet on independent board and multistrand PVC insulated copper earth continuity conductor of size 4 Sqmm complete all as specified and directed.

S&F modular switch, 6 Amps, single pole, one way complete all as specified and directed.

S&F modular switch, 16 Amps, single pole, one way complete all as specified and directed.

S&F modular socket outlet 2/3 Pin 6 Amps combined 2 module complete all as specified and directed.

S&F modular Socket multipurpose 3 pin 16 Amps and 3 pin 6 Amps combined 2 module complete all as specified and directed.

S&F Bell push switch Modular type single pole one way 6 Amp 240 Volts complete all as specified and directed

S&F Modular step type fan regulator 120W, 2 module ,heavy duty, 240 volts complete all as specified and directed

S&F Ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body complete all as specified and directed.

M&L for Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendent/Angle type including one lamp complete all as specified and directed.

Taking down old unserviceable submain wiring/ service wire of any size complete all as specified and directed.

S&F in repair for submain wiring with single core 6.0 sqmm PVC FRLS insulated unsheathed cable multistranded copper conductor drawn through and inclduing PVC casing capping of suitable size with all fittings and fixing accessories on roof , walls, ceiling etc including 6.00 Sqmm PVC insulated unsheathed one core multistranded copper condutor earth wire complete all as specified and directed. (Note : Two runs of single core cable and one run of earth wire will be measured as one length)

S&F in repair for submain wiring with single core 4.0 sqmm PVC FRLS insulated unsheathed cable multistranded copper conductor drawn through and inclduing PVC casing capping of suitable size with all fittings and fixing accessories on roof , walls, ceiling etc including 4.00 Sqmm PVC insulated unsheathed one core multistranded copper condutor earth wire complete all as specified and directed. (Note : Two runs of single core cable and one run of earth wire will be measured as one length)

S&F of 1100 volts grade heavy duty cable PVC insulated aluminium conductor (Service wire) served with inner sheating of PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than one meter apart including 4 mm suspension wire one twin core cable 2 core flat of 10 sqmm size

S&F in repair 23/.0076 sqmm 2 core flexible copper cable for maintenance of light/ fan etc complete all as specified and directed.

S&F in repair socket outlet, 3 pin, piano type, 5 Amps, complete all as specified and directed.

S&F in repair socket outlet, 3 pin, piano type, 15 Amps, complete all as specified and directed.

S&F in repair switch piano type single pole one way 5 Amp 240 Volts complete all as specified and directed

S&F in repair switch piano type single pole one way 15 Amp 240 Volts complete all as specified and directed

S & F in repair switch socket combination 2 in 1, 3 pin, 5 and 15 Amps, piano type universal 240 Volt complete all as specified and directed

S&F in repair Bell push piano type single pole 5 Amp 240 Volts complete all as specified and directed.

S&F in repair of stepped type electronic fan regulator piano type, 230 Volt, 5 speed control complete all as specified and directed.

S&F in repair modular switch, 6 Amps, single pole, one way complete all as specified and directed.

S&F in repair modular switch, 16 Amps, single pole, one way complete all as specified and directed.

S & F in repair modular socket outlet 2/3 Pin 6 Amps combined 2 module complete all as specified and directed.

S & F in repair modular socket outlet 6/16 Amp 5 pin 2 module 240 Volts complete all as specified and directed

S & F in repair modular bell push 6 Amps 1 module 240 Volts complete all as specified and directed

S&F in repair Modular stepped type electronic fan regulator, 230 Volt, 5 speed control complete all as specified and directed.

S & F blank speacer plate for single module complete all as specified and directed.

Taking down old unserviceable PVC box any type any size complete all as specified and directed.

S&F in repair modular PVC Box including White cover plate with frame, 1 module complete all as specified and directed.

S&F in repair modular PVC Box including White cover plate with frame, 2 module complete all as specified and directed.

S&F in repair modular PVC Box including White cover plate with frame, 3 module complete all as specified and directed.

S&F in repair modular PVC Box including White cover plate with frame, 4 module complete all as specified and directed.

S&F in repair modular PVC Box including White cover plate with frame, 6 module complete all as specified and directed.

S&F in repair modular PVC Box including White cover plate with frame, 8 module complete all as specified and directed.

S&F in repair modular PVC Box including White cover plate with frame, 12 module complete all as specified and directed.

S&F in repair PVC rectangular block for mounting switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet cover of size 100mm x 100mm x 50 mm complete all as specified and directed.

All as per serial item No.166 here-in-above but for size 175x100x50 mm deep complete all as specified and directed.

All as per serial item No.166 here-in-above but for size 200x150x50 mm deep complete all as specified and directed.

All as per serial item No.166 here-in-above but for size 250x200x50 mm deep complete all as specified and directed.

All as per serial item No.166 here-in-above but for size 350x300x50 mm deep complete all as specified and directed.

S&F in repair bell Buzzer, Ding Dong Type , AC 230 Volts single pole complete all as specified and directed.

S&F in repair Ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body complete all as specified and directed.

S&F in repair of Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendent/Angle type complete all as specified and directed.

Taking down old unserviceable MCB DB any type any way complete all as specified and directed.

S&F in repair sheet metal enclosure DB, TPN, IP 43 protection, double door, 240 volts, Vertical Type 4 way with copper bus bars suitable for mounting MCBs of minimum 415 Amps rating complete all as specified and directed.

S&F in repair sheet metal enclosure for MCB’s distribution board, 240 Volts, 12 ways single pole and neutral including 200 Amps rated busbar, neutral link, din rail double door Type for breaking capacity 10 KA complete all as specified and directed.

S&F in repair sheet metal enclosure for MCB’s distribution board, 240 Volts, 8 ways single pole and neutral including 200 Amps rated busbar, neutral link, din rail double door Type for breaking capacity 10 KA complete all as specified and directed.

S&F in repair sheet metal enclosure for MCB’s distribution board, 240 Volts, 4 ways single pole and neutral including 200 Amps rated busbar, neutral link, din rail double door Type verticle for breaking capacity 10 KA complete all as specified and directed.

S & F in repair single pole and neutral enclosure with a two pin and earth plug and socket complete with one single MCB SP 20 Amps 10 KA complete all as specified and directed.

S&F in repair MCB single pole 06 to 32 Amps, ‘C’ series 240 Volts, breaking capacity 10KA complete all as specified and directed.

S&F in repair MCB single pole and neutral 32 Amps, ‘C’ series 240 Volts, breaking capacity 10KA complete all as specified and directed.

S&F in repair of MCB single pole and neutral 40 to 63 Amps, ‘C’ series 240 Volts, breaking capacity 10KA complete all as specified and directed.

S&F in repair of MCB TPN four pole 40 to 100 Amps, ‘C’ series 415 Volts, breaking capacity 10KA complete all as specified and directed.

S&F in repair of PVC conduit size 25mm Rigid non-metallic PVC conduit exclusive of boxes (junction/terminal) but inclusive of all tees, bends,elbows, reducers, bell mouth tube ends and fixing accessories including chase cutting such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified and directed

S&F in repair PVC Flexible pipe 16/20mm in dia for covering of electrical wire complete all as specified and directed.

Taking down old Unserviceable LED light fittings any type complete all as specified and directed.

S & F in repair LED light fitting mirror type with high out put diffuser 2 feet,10 watt 220 V AC decorative type white/ warm with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete complete all as directed by Engr-in-charge.

S & F in repair LED lights fitting 1x 20W, 220V, AC decorative box type white/ warm with driver, holder including LED tube light 20W connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as directed by Engr-in-charge.

S & F in repair LED lights fitting 1x 20W, 220V, Inverter type AC decorative box type white/ warm with driver, holder including LED tube light 20W, with 4 hours backup, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as directed by Engr-in-charge.

S&F in repair LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type white/warm with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S & F in repair round/ square shape 6 watt 220 volts AC recessed type white/warm with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S & F in repair round/ square shape 15/18 watt 220 volts AC recessed type white/warm with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F in repair LED builidng security light fitting 25 Watt 230 V, AC out door type with hih pressure dia cast aluminium hosing and heat resistant complete with driver , lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

S & F in repair LED bulb Lamp 09-12 Watts Retrofit B22 holder type white/warm base wth polycorbonate diffuser and alluminiun heat sink complete all as specified and directed.

S & F in repair LED bulb Lamp Inverter light 09-12 Watts Retrofit B22 holder type white/warm base wth polycorbonate diffuser and alluminiun heat sink, with 4 hours electric backup complete all as specified and directed.

S & F in repair Driver of LED recesses mounted Panel light (2'x2') 36 watt complete all as specified and directed.

Taking down and dismantling of storage type water geysers of 25/50 ltrs capacity any type any make, any model, from its existing location, transportation to work shop for repairs and transportation back and reinstallation of geyser as per technical instructions and as directed by engr-in-charge and including the following:- (a) Dismantling complete geyser and carrying out complete overhauling i.e; disconnecting electric supply and opening the heating plate, inner assembly, descaling complete assembly including heating element or otherwise. Replacement of defective heating element inlet and outlet tubes and refixing the assembly with gasket of good quality and tightening the nuts properly, reassembling geyser with all safety devices as specified in technical instructions and as directed by Engineer -in- Charge complete. Notes:- (i) Spare parts, safety devices with its required accessories shall be measured and paid seperately .

Supply only following spare parts of geysers 50/25 Ltrs capacity ISI marked.

Heating element 1.5/2 KW suitable for operation on 230V AC 50Hz

Thermostat 40 to 90 degree centigrade varying capactiy for 25/50 Ltrs capacity Geyser.

Flexible conneciton pipe with brass check nuts complete as per site requirement all as specified and directed by Engineer-In-Charge.

Indicator lamp assembly for geyser complete all as specified and directed by Engr-In-Charge.

Syphon assembly suitable for 25/50 ltr geyser complete including nuts and washer complete all as specified and directed.

Geyser brass tank for 25/50 ltr geyser complete including nuts, washer, glass wool etc complete all as specified and directed.

S&F in repair 15 Amp plug top complete all as specified and directed.

M&L in repair for Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to galvanized earth wire 4mm dia by means of galvanized iron or steel bolts nuts check nuts and washers and other end connected with earthing testing point including providing suitable testing points as directed including funnel, watering pipe of 20mm bore, light grade galvanized iron pipe, wire mesh charcoal of coal dust and common salt in alternative layer all around the earth electrode compacted thickness 15cm with concrete pit in PCC 1:3:6 type C1 50mm thick pre cast RCC 1:2:4 type B1 cover slab set in CM (1:4) re-enforcement with 8mm dia deformed bars @ 15cm C/C and suitable handle of 10mm dia MS round bars, including earth work in hard/dense soil as required complete all as shown in electrical plate No 3 of MES Schedule Part I and testing on completion complete all as specified and as directed. (Note: Earth strip beyond 7.5 m length will be measured & paid separately)