Up-gradation/Re-Construction of existing emergency Ward(Ground floor) at Gauhati Medical College AND Hospital as per latest NMC norms

Amount

SUB HEAD-I :- CONCRETE WORKS Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

SUB HEAD-II :- MASONRY WORK Providing and laying autoclaved aerated cement blocks masonry with 150mm//200mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

SUB HEAD-III:- WOOD WORK Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured): Rectangular or square.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. (Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge) (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing 12 mm thick frameless toughened glass partitions of approved brand and manufacturer with all necessary aluminium patch fitting hardware like corner, side, top & bottom and corner connector with all fixing arrangements and making necessary holes etc. for fixing required fittings complete including providing and fixing top & bottom with aluminum channel etc. or as specified in the drawing all complete as per direction of Engineer-in-charge

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing 85x42 mm chromium plated brass pull bolt lock with necessary chromium plated brass screws, nuts, bolts and washers etc. complete.

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

Providing and fixing to existing door frames. 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge.

HARDWARES FITTINGS FOR DOOR Providing and fixing approved brand and manufacturer SS 304 grade hardware's for Doors etc. GLASS DOOR Providing and fixing approved brand and manufacture SS 304 grade D type 1200mm Pull Handle with 32mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade D type 300mm Pull Handle with 32mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Glass to Glass Lock Round type with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

WOODEN Providing and fixing approved brand and manufacture SS 304 Lever Handle D-type fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade SS 304 grade Mortice lock with key cylinder fixed fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Tower bolt 250mm long with 10mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Tower bolt 150mm long with 10mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade wall mounted door buffer fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Door Stopper - door mounted hanging type fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Steel Fire door :-Providing and fixing 120 minutes Fire Rating Metal Fire door with galvanised GI sheet as per IS 277, door must also suffice the critrian of 30 minutes insulation as per NBC 2016 guidelines, Prototype sample of the door must carry a prior test evidence as per IS 3614 part-2 / BS 476 Part 20 & 22, door should be finished with Powder coating in desired regular RAL Shades door frame shall be Single rebate grooved profile of section 100 x 57 mm made out of 1.20mm thick galvanised steel sheet with a factory pre-punched groove so as to accomodate Fire & smoke seal size 10x4mm, Frames should be butt jointed and field assembled with bolting system for proper strength, Frames should be provided with back plate for anchor fasteners for installation on a finished plastered wall opening, Any filling in frames is not suggested, door leaf should be 46mm thick fully flush double skin, door leaf should be 0.8mm (22 guage) thick galvanised steel sheet, door should be provided with reinforcement pads & necessary provision for receiving appropriate and complete Hardwares,Shutter shall be filled with proprietary infill material Honey Komb Craft paper Insulation, For Double leaf doors will have astragal at their meeting stile for both active and inactive leaf, Vision panels wherever required should be of 120 minutes fire rating and should be of non-wired type, door and the frames shall be finished with powder coating and shall pass the minimum 500hours Salt Spray test evidence.

Providing & fixing galvanized low carbon wire, anealed wire Chicken mesh formed by twisting two adjacent wires at least four times, forming a hexagonal shaped strong honeycomb mesh structure on joints of RCC & Brick work before plastering, of required gauge (not less than 21 gauge)and size with nails etc. complete as specified in drawing and as per the Direction of Engineer-in-charge.

SUB HEAD-IV :- STEEL WORK Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and fixing stainless steel ( Grade 316) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

SUB HEAD- V :- FLOORING Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size a ) Size of Tile 600x600 mm

b ) Size of Tile 800x800 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm

Size of Tile 800x800 mm

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complete.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Extra for pre finished nosing to treads of steps of Granite stone.

Extra for Granite stone flooring in treads of steps and risers using single length up to 2.00 metre .

GRANITE WORK FOR COUNTER Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, cherry/ruby red Area of Slab over 0.50sqm

Providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work.

Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

SUB HEAD-VI:- ROOFING & FALSE CEILING Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power press ed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of size 24x25 mm made of 0.30mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.

SUB HEAD-VII :- PAINTING AND FINISHING WORK 12mm cement plaster of mix : 1:6 (1 cement : 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement : 6 fine sand)

6 MM CEMENT PLASTER 6 mm cement plaster to ceiling of mix : 1:3(1 cement: 3 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two Coat

Painting with synthetic enamel paint of approved brand and manufacture of required color to give an shade. Two or more coats on new work including priming coat of ordinary paint approved brand.

SUB HEAD-VIII:- ALUMINIUM WORK Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separately). Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge. Pre-laminated particle board with decorative lamination on both sides

SUB HEAD-IX- DISMANTLING AND DEMOLISHING Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Of area beyond 3 sq. metres

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

For thickness of tiles above 25 mm and up to 40 mm

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge : 15 mm to 40 mm nominal bore

Above 40 mm nominal bore

Dismantling C.I. pipes including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes & lead at site within 50 metre lead as per direction of Engineer-in-charge: Up to 150 mm diameter

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Plumbing Work: SUB HEAD-8.0 MARBLE & GRANITE WORK Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade

SUB HEAD-12.0 ROOFING Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter

110 mm diameter

160 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single Push Fit Coupler 160 mm dia

Single tee without door 160 mm dia

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 160 mm dia

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

SUB HEAD-17.0 SANITARY INSTALLATIONS Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing white vitreous china Oval shaped wash basin for top/under counter mounting with 15 mm C.P. brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls whereever required. ( MAKE-1: JAQUAR, MODEL NO. WASH BASIN : FSS-WHT-29601 & BASIN MIXER : FLR-CHR-5001BG & WASTE COUPLING : ALD-CHR-705 OR EQUIVALENT.) White Vitreous China Oval shaped Wash basin size 545 x 545 x 180mm with 15mm CP Brass single hole basin mixer with flow rate 2.5 litre per minute at 3 bar .

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm

Providing and fixing hand shower (Health faucet) with 1.2mtr long with 8mm dia Easy Flex Tube with wall hook and flow restrictor with flow rate 6 litre per minute at 3 bar in chrome finish and wall hook. ( MAKE-1: JAQUAR, MODEL NO. HEALTH FAUCET : ALD-CHR-573GA OR EQUIVALENT.)

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. ( MAKE-1: JAQUAR, MODEL NO. BOTTLE TRAP : ALD-CHR-769L300X190 OR EQUIVALENT.)

Providing & fixing PVC waste pipe for sink including PVC waste fitting Complete Semi rigid pipe 40mm Dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing & fixing toilet paper holder C.P. Brass

Providing and fixing soil waste vent & rain water pipes 100 mm dia. Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing M.S. holder-bat clamps of approved design to sand cast iron/ centrifugally cast iron(spun) pipes embedded in and including cement concrete blocks 10x 10 x 10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls, etc. For 100mm dia pipe

Providing and fixing bend of required degree with access door insertion rubber washer 3mm thick, bolts and nuts complete 100 mm dia Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing plain bend of required degree: 100 mm dia Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing double equal plain junction of required degree. 100 x 100 x 100 x 100mm Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing single equal plain junction of required degree. 100 x 100 x 100mm Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing single unequal plain junction of required degree : 100x100x75 mm Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe 100 mm SS 304 grade coupling with EPDM rubber gasket

Providing and fixing trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vent, arm complete, including cost of cutting and making good the walls and floors. 100mm inlet and 100mm outlet Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/ cast iron (spun) pipes comprising of M.S. flat brackets made of 50x5 mm flat of specified shape, projecting 75 mm outside the wall surface and fixed on wall with 4nos, 6mm dia expansion hold fasteners, including drilling necessary holes in brick wall/ CC/RCC surface and the cost of bolts etc. The pipes shall be fixed to the already fixed brackets with the help of 30 mm x1.6 mm galvanised M.S. flats of specified shape and of total length 420 mm and shall be fixed with M.S. nuts, bolts, & washers of size 25x6 mm, one bolts on each side of the pipe. Total bracket length 580 mm of approved shape and design (for single 100 mm dia pipe)

Total bracket length 810 mm of approved shape and design (for two 100 mm dia pipes)

Total bracket length 1040 mm of approved shape and design (for three 100 mm dia pipes)

Providing & fixing Nickel Chromium Plated liquid soap container/dispenser with metallic bottle of approved brand & make 112 mm distance from wall of standard shape with bracket (Nickel chromium plating should pass Salt Spray Test for 200 hours) of the same materials with snap fittings of approved quality and colour, complete as per direction of Engineer in Charge. ( MAKE-1 : JAQUAR, MODEL NO. - ACN-CHR-1137N OR EQUIVALENT.

Providing, Fixing of CP brass Towel Ring with CP brass wall brackets and providing & fixing CP brass screws complete as required. ( MAKE-1: JAQUAR, MODEL NO. TOWEL RING : ACN-CHR-1121N OR EQUIVALENT.)

Providing & fixing soap dish holder of approved design. ( MAKE-1: JAQUAR, MODEL NO. SOAP DISH : ACN-CHR-1131N OR EQUIVALENT.)

Providing and fixing white vitreous china Oval shaped wash basin for top/under counter mounting with 15 mm C.P. brass pillar tap of auto closing type of approved quality and make with, including painting of fittings and brackets, cutting and making good the walls whereever required. ( MAKE-1: JAQUAR, MODEL NO. WASH BASIN : FSS-WHT-29601 & PILLAR TAP : PRS-031G & WASTE COUPLING : ALD-CHR-705 OR EQUIVALENT.) (a) White Vitreous China Oval shaped Wash basin size 545 x 545 x 180mm with 15 mm C.P. brass pillar tap auto closing type of approved make with flow rate 2.5 litre per minute at 3 bar .

Providing and fixing CP brass single lever low flow wall mounted Sink mixer with 15 mm CP brass single lever swivel spout with waste complete with flow rate 2.5 litre per minute at 3 bar including cutting and making good the walls where required. ( MAKE-1: JAQUAR, MODEL NO. SINK MIXER : FLR-CHR-5163GD OR EQUIVALENT.)

Providing , Fixing of CP Brass 450mm long Shower Arm with wall flange and pressure adjustable Overhead Shower with rubit cleaning system with flow rate 6 litre per minute at 3 bar complete with all accessories as required and making good the walls wherever required. ( MAKE-1: JAQUAR, MODEL NO. SHOWER ARM : SHA-CHR-479L450 & OVERHEAD SHOWER : OHS-CHR-1759GA OR EQUIVALENT.)

Providing,Fixing wall mounted Double Coat hook on door complete. ( MAKE-1: JAQUAR, MODEL NO. COAT HOOK : AKP-CHR-35761P OR EQUIVALENT.)

Providing & fixing wall mounted 300mm Long SS Grab Bar including cutting & making good the walls. ( MAKE-1: JAQUAR, MODEL NO. GRAB BAR : AKP-CHR-35701PS OR EQUIVALENT.)

Providing and fixing CP brass 2 Way Bib cock with wall flange with flow restrictor with flow rate 2.5 litre per minute at 3 bar. ( MAKE-1: JAQUAR, MODEL NO. 2 WAY BIB COCK : FLR-CHR-5041NG OR EQUIVALENT.)

Providibng and fixing straight type Macfit single body push fit type WC pan connector with factory supplied spring loaded seal guard of McAlpine, UK with integral single mould sealing fins made of flexible EVA body, including bush/adaptor for use with C.I. Pipe as supplied with the pan connector.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing complete as required. (MAKE-ModiGuard Sparkle Mirror )

Providing & fixing 100mm x 50mm G.I. waste with reducing elbow & nipple cutting chases, the floor / slab, repairs complete as required and connection to GI / CI waste pipe.

Providing and fixing cast brass Floor cleanout plug with suitable insert keys for opening in brass cap, male threaded joint/reducer with G.I. socket caulked to Pipe/fittings of CI pipe including cost of lead joints etc. complete in all respect. (a) 100 mm dia

Providing and fixing GI inlet fitting with maximum 3 inlets 32,40 or 50 mm size fabricated from 100 dia GI pipes and sockets,fixed to C.I. trap with Drip Seal joint and set in cement concrete as per standard drawing complete as directed by Engineer-incharge.

Providing and fixing SS Grating of 125 mm dia of approved quality and colour complete as per direction of engineer in charge. (a) Circular Type 125 mm nominal dia with 25 mm waste hole

Providing, Installing & fixing storage type water heater of approved shade with copper container, glasswool insulation,stove enamelled M.S jacket, thermostatically controlled inner heater with pilot neon lamps, 15mm inlet stop cock valve, on inlet connection, 15mm dia C.P flexible connection pipe in inlet & outlet suitable for working pressure of 8 kg/sqcm complete as required. (a) Capacity 25 litres size 448X448X345mm ( MAKE-1: JAQUAR, MODEL NO. GEYSER : ELENA OR EQUIVALENT.)

(b) Capacity 40 litres size 875X400mm ( MAKE-1: JAQUAR, MODEL NO. GEYSER : VERSA HORIZONTAL MANUAL OR EQUIVALENT.)

SUB HEAD-18.0-WATER SUPPLY Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia .Pipes.

20 mm nominal outer dia .Pipes.

25 mm nominal outer dia .Pipes.

32 mm nominal outer dia .Pipes.

Providing and fixing GI pipes complete with GI fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on Wall 15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External Work 25mm nominal nominal bore

32mm nominal nominal bore

40mm nominal nominal bore

50mm nominal nominal bore

65 mm nominal nominal bore

80 mm nominal nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20mm nominal bore

25mm nominal bore

32mm nominal bore

40mm nominal bore

50mm nominal bore

65mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore

25mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S (non modular) bricks of class designation 7.5

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : 20mm diameter pipe

25mm diameter pipe

32mm diameter pipe

40mm diameter pipe

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality. 32mm diameter pipe

Providing and fixing C.P. brass Short body bib cock of approved quality conforming to IS:8931 with flow rate 2.5 litre per minute at 3 bar: (MAKE-1: JAQUAR, MODEL NO. SHORT BODY BIB COCK : FLR-CHR-5037NG OR EQUIVALENT.) 15mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms with flow rate 2.5 litre per minute at 3 bar. (MAKE-1: JAQUAR, MODEL NO. LONG BODY BIB COCK : FLR-CHR-5047NG OR EQUIVALENT.) 15mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixture and geyser points of approved quality confirming to IS: 8931. (MAKE-1: JAQUAR, MODEL NO. ANGLE VALVE : AQT-CHR-3057 OR EQUIVALENT.)

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : 50 mm dia

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Making hole up to 20x20 cm and embedding pipes up to 150 mm diameter in masonry and filling with cement concrete 1:3:6 (1 cement : 3 coarse sand 6 graded stone aggregate 20 mm nominal size) including disposal of malba.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end). (a) 15mm nominal bore

Providing & fixing CI `Y' Strainer (screwed/ flanged) with stainless steel fine wire mesh perforated sheet basket with necessary flange/ unions nuts, bolts and washers complete as required. (a) 32mm nominal bore

Providing and fixing motorised butterfly valve with float type sensors suitable for 240 volts with working pressure rating of not less than 6 kg/cm2 with control panel and sensors to open valve when water level is low in tanks and to close when water level is high in water tanks including necessary cables, conduits, upto junction box (upto 6 mt qty approx.) etc., complete. 32 mm dia

Providing and fixing water meter with direct reading dial in "KL" with all internal parts in gunmetal , strainer, flanged distance piece for easy removal in future, 100 mm dia Bourden type pressure guage and isolation cock including necessary test certificate for the meter. (For water supply metering from source). 32 mm dia

SUB HEAD : 19.0- DRAINAGE Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : 180 x 150mm size P-type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610mm internal dimensiions total weight of cover and frame to be not less than 38 Kg. ( weight of cover 23 Kg. and weight of frame 15 Kg.), with FPS bricks with class designation 7.5 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 50x45x60cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450mm precast RCC horizontal grating with frame complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

(Electrical works) : POINT WIRING Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2x1.5 sq. mm + 1x1.5 sq. mm earth wire

2x10 sq. mm + 1x6 sq. mm earth wire

4x10 sq. mm + 2x6 sq. mm earth wire

4x16 sq. mm + 2x6 sq. mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ conduit as required. 6 x 1.5 sq. Mm

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch

2 way 5/6 A switch

15/16 A switch

3 pin 5/6 amp socket outlet

6 pin 15/16 A socket outlet

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 1 or 2 Module (75mmX75mm) - For Telephone,TV outlet & Data

3 Module (100mmX75mm) - For Socket outlet.

6 Module (200mmX75mm) - For Socket outlet.

8 Module (125 mmX125 mm)

12 Module (200 mmX150 mm)

SUPPLY & INSTALLATION OF LIGHT FITTING Supply, installation, Testing & Commissioning of 10 Watt LED batten Light (600mm), 6500K, having minimum system lumen output of 100 Lumen / watt complete as requried. (Mirror Light)

Supply, installation, Testing & Commissioning of 18-20 Watt LED batten Light (1200mm), 6500K, having minimum system lumen output of 100 Lumen / watt complete as requried.

Supply, installation, Testing & Commissioning of 36 Watt, recessed mount, 6500K, LED light fixture, of size 2' x 2', having minimum system lumen output of 100 Lumen / watt complete as requried.

Supply, installation, Testing & Commissioning of 10-12 Watt Recess mounted LED Down Light, 6500K, having minimum system lumen output of 100 Lumen / watt complete as requried.

Supply, installation, Testing & Commissioning of 18 Watt Recess mounted LED Down Light, 6500K, having minimum system lumen output of 100 Lumen / watt complete as requried.

DISTRIBUTION BOARDS & PANELS Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (a) 12 way, Double door

(b) 16 way, Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 Way (4+24), Double Door

12 way (4 + 36), Double door

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc. as required. For 14 way, Double door SPN MCBDB

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface / recess, complete with testing and commissioning etc.as required. For 8 way, Double door TPN MCBDB

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) Single pole

(b) Double pole

Supplying and fixing following rating, double pole, 240 volts, MCB complete with connections, testing and commissioning etc. as required. Supplying and fixing of following rating, 240/415 volts, "C" curve, four pole miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 Amp Triple pole & neutral MCB

40 Amp Triple pole & neutral MCB

Supplying and fixing of following rating double pole (Single phase and neutral) 240 volts, residual current circuit breaker (RCCB), having a current sensivity current 30 miliampere in the existing MCB DB complete with connections, testing & commissioning etc. as required. (a) 25 Amps

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Design, Manufacturing, Supply, Installation, Testing & Commissioning of cubicle type totally enclosed free standing / Wall mounted type moisture, dust and vermin proof compartmentlized Floor Distribution Panel made out of 2.0 mm thick of Main members & front cover 1.6 mm thick CRCA sheet complete with internal wiring with suitable size wires / cable, interconnection, painting complete as per specification & drawing. The MCCB rating up to 250A shall have thermal megnatic based adjustable over current, short circuit protection and above 250A MCCB shall have microprocessor based adjustable over current, short circuit, earth fault protection. UPS INCOMING PANEL INCOMING 1 No. 125 Amp FP Moulded Case Circuit Breaker. 1 Set of phase indicating lamps with MCB. 1 Set of ON/OFF indicating lamps with MCB. 1 No. Digital MFM with CT's. BUSBAR 150 Amp TPN aluminium busbar with coloured heat shrinkable sleeve. OUTGOING 3 Nos. 100 Amp TP+N Moulded Case Circuit Breaker. UPS Incoming Panel described as above

UPS OUTGOING PANEL INCOMING 2 Nos. 100 Amp FP Moulded Case Circuit Breaker. 2 Set of phase indicating lamps with MCB. 2 Set of ON/OFF indicating lamps with MCB. 2 No. Digital MFM with CT's. BUSBAR 150 Amp TPN aluminium busbar with coloured heat shrinkable sleeve. OUTGOING 5 Nos. 63 Amp FP Miniature Circuit Breaker. 3 Nos. 25 Amp DP Miniature Circuit Breaker. UPS Outgoing Panel described as above

POWER PANEL INCOMING 1 Nos. 200 Amp FP Moulded Case Circuit Breaker. 1 Set of phase indicating lamps with MCB. 1 Set of ON/OFF indicating lamps with MCB. 1 No. Digital MFM with CT's. BUSBAR 250 Amp TPN aluminium busbar with coloured heat shrinkable sleeve. OUTGOING 4 Nos. 63 Amp FP Miniature Circuit Breaker. 4 Nos. 40 Amp FP Miniature Circuit Breaker. 1 No. 125 Amp FP Moulded Case Circuit Breaker. Power Panel described as above

EARTHING Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

DISTRIBUTION POWER PANEL AND CABLE Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Above 185 sq. mm and upto 400 sq. Mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. Above 185 sq. mm and upto 400 sq. Mm

Supply of following size PVC/XLPE insulated and PVC sheathed 1.1KV gd Solid Aluminum conductor up to 10 sqmm, balance stranded conductor, XLPE Insulated, cores laid up, PVC tape innersheathed, Armour (Aluminium wire for single core up to 70 sqmm, balance Aluminium strip, Glavanised wire for cables upto 2x10 sqmm,, 3x10 sqmm,,4x6 sqmm, & balance all galvanised steel strip), extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable as specified and directed by the deptt. ( Havells or equivelent make) a) 300.00 Sq.mm3&1/2 core armoured U.G. cable

b) 240.0 Sqmm 3&1/2 core armoured

c) 120.0 Sqmm 3&1/2 core armoured

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 200 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal)

Supplying including installation, commissioning of vermin and dust proof totally enclosed, Phosphatised Powder Painted cubical outdoor type double door, floor mounting compartmentalize panel board of size 2.6M(B)X 1.6M(H) X 0.40M(D) made of 16 SWG (1.66 mm) thick C.R. sheet and 40mm X 40mm X 5mm size angle having 4 nos legs at the bottom and C.R. sheet roofing on the top. The panel board is to be errected in 1 : 3 : 6 PCC foundation including excavation of trench and brick soling etc. complete neatly wiring done with provision for one no 400A 4pole MCCB as incomer and provision for 6nos TPN out going as specified and directed by the deptt. confirming to IP 65 protection comprising of the following electrical items: 1. i) 30mm X 5mm 4 strip copper Bus - Bar 1.20 M length each ii) 20mm X 3mm 4 strip copper Bus-Bar 0.5M each 4 sets 2. Poilt Lamp with integral ckt LED 110- 230 V (Red,Yellow,& Blue) - 3 nos 3. Multifunction Meter - 1 no 4. 2 A Slide fuse unit - 3nos (Incoming & Outgoing Switch Gear of reqd. rating will be measured and paid separately)

Supplying including installation, commissioning of vermin and dust proof totally enclosed, Phosphatised Powder Painted outdoor type single door Bus Bar enclosure (Feeder Piller) of size 0.60M(B)X 0.80M(H) X 0.40M(D) made of 16 SWG (1.66 mm) thick C.R. sheet and 30mm X 30mm X 5mm size angle having 4 nos legs at the bottom and C.R. sheet roofing on the top. The box is to be errected in 1 : 3 : 6 PCC foundation including excavation of trench etc. 4strip Copper bus bar for out going as specified and directed by the deptt. confirming to IP 65 protection comprising of the following electrical items: 1. i) 25mm X 5mm 4 strip copper Bus - Bar 0.42 M length each

Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 Amp, 30KA, FPMCCB

125 Amp, 36KA, FPMCCB

250 Amp, 36KA, FPMCCB

250 Amp, 50KA, FPMCCB

400 Amp, 50KA, FPMCCB

Supply with installation & commissioning of readymade maintenance free CPRI approved chemical earthing system with 100 MM dia. 2.9 Metres length corrossion free centrifugally Cast Iron Earthing Electrode complete with Reslow/BFC Grounding chemical compound ( 40 KG) and Advance Earth Pit cover (CI) of size 300 mmx300 mm including excavation of earth pit and construction brick earth chamber including plastering both inner & outer surface of brick wall as specified and directed by the deptt. 100 mm Dia Chemical Earthing

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

CABLE TRAY'S, RACE WAYS (LT Cables and Terminations) Supplying following 1.1kV grade, heavy duty XLPE insulated PVC Sheathed Copper Conductor FRLS type armoured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath provided with FRLS insulation, galvanised steel armouring (round or flat as mentioned) and with all components as mentioned in BOQ, specifications and schedule, complete etc. as required. 4 core, 16 sq.mm.Cu.Cable

4 core, 10 sq.mm.Cu.Cable

4 core, 6 sq.mm. Cu.Cable

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with cable tie)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. (a) 4 X 10 sq. mm (25mm) (The Termination including 4 x 6 sq. mm cable)

(b) 4 X 16 sq. mm (28mm)

(Cable Trays) Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. (a) 100 mm width x 50 mm depth x 1.6 mm thickness

(b) 150 mm width x 50 mm depth x 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “bends” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. (a) 100 mm width x 50 mm depth x 1.6 mm thickness

(b) 150 mm width x 50 mm depth x 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Tee” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. (a) 100 mm width x 50 mm depth x 1.6 mm thickness

(b) 150 mm width x 50 mm depth x 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Cross member” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. (a) 100 mm width x 50 mm depth x 1.6 mm thickness

(b) 150 mm width x 50 mm depth x 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Reducer” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. (a) 100 mm width x 50 mm depth x 1.6 mm thickness

(b) 150 mm width x 50 mm depth x 1.6 mm thickness

Supply & fixing of following size (GP RACEWAY- Fabricated from GP Sheet) race ways for electrical & LV wiring including neoprene gasket in joints, cutting the floor & jaming the race way / hanging in ceiling, supporting arrangement as approved by consultant / architect with all necssary hard ware (including civil work) as per site requirement. The thickness of raceway & cover shall be as per technical specification. (a) 100 mm wide x 40 mm deep.

(b) 150 mm wide x 40 mm deep

(c) 200 mm wide x 40 mm deep

Supply & fixing of following size of Raceway Junction Box made out of GP Sheet for electrical & LV wiring including, cutting the floor & jaming the junction box / hanging in ceiling, supporting arrangement as approved by consultant / architect with all necssary hard ware (including civil work).(Junction box to be provided as per drawing/ as per site requirement & as per specification). The thickness of junction box shall be a as per thechnical specification. (a) 150 mm wide x 50 mm deep.

(b) 200mm wide x 50 mm deep

(c) 250mm wide x 50 mm deep

TV SYSTEM Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. TV antenna socket outlet

Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.

Supplying, installation, testing & commissioning of fire fighter phone jack complete as required.

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

PUBLIC ADDRESS SYSTEM- Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. Speaker cable Single pair, 2-core, 1.5 sqmm

IP BASED CCTV SYSTEM Supply ,Installation ,Testing & Commossioning of 3 MP Dome Camera, ONVIF profile S & G , UL,CE,FCC certified , Motorized varifocal 3mm to 9 mm ,1/2.8" CMOS sensor , Quad stream, frame rate : H.264 3M (2048 X 1536) @25/30 fps, 2 MP (1920 X 1080) @ 50/60 FPS, Shutter speed : 1 ~1/10000 sec , P-iris , Min illumination : Color 0.04 lux , B/W 0.002 lux , Auto ICR ,Two way audio support ,Video compression : H.264/H.265 ,MJPEG ,120 dB WDR ,Auto white balance , SD Card support ,Support upto 20 user accounts , 1 X BNC analog output ,Digital Zoom ,Digital PTZ ,2D / 3D Noise reduction, Edge analytics : Abandoned Object, Intrusion Detection, Tampering, Wrong Direction, Loitering Detection, Object Counting, Stopped Vehicle, Object Removal , InbuiltIR LEDs , IR distance upto 40 mtrs , IP 66 weather proof , IK 10 Vandal proof ,POE.

Supply, installation, Testing and Commissioning of Open Platform ONVIF profile S &G 8 Channel Network Video Recorder, Intel based, Full Rack, RAID 0/1/5/10, @ 2M/30FPS, 1*2.5" SATA + 8 * 3.5" SATA, Throughput: 640 Mbps.1 X HDMI , 1X VGA ,, 1 X mic in , 1 X line out , USB 3.0 x 2 + USB 2.0 x 3 , 1 X WAN port , 1 X LAN port, pre-installed VMS.

Supply, Installation, Testing & Commissioning of 6TB HD.

Supply, Installation, Testing & Commissioning of 65" LED panels as per NIT Specification.

Supply , Installtion , Testing and comissioning of CAT6 information outlet (I/O) for CCTV.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. (a) 1 Run of Cable

(b) 2 Run of Cable

(c) 3 Run of Cable

DATA, TELEPHONE SYSTEM Supply ,Installation ,Testing & Commossioning of CAT 6A F/UTP cable 23 AWG solid copper conductors with flame retardant properties, in compliance to relevant IEC standards complete etc.

Supply , Installtion , Testing and Comissioning of CAT6A Shielded information outlet (I/O) for Data, Voice rack end

Supply , Installtion , Testing and Comissioning of loaded 24 port CAT 6A jack panel for CAT6A cable termination

Supply , Installtion , Testing and Comissioning of CAT 6A Shielded patch cord 3 feet for rack side switch termination for user End

Supply , Installtion , Testing and comissioning of CAT 6A Shielded patch cord 7 feet for user termination to information outlet Rack End

Supply , Installtion , Testing and comissioning of 1, 2 and 4 port face plate white for I/O fixing at user side.

Supply , Installtion , Testing and comissioning of 15U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos of hardware pkts., 6 Socket PDU with MCB.

Supply, Installation, Testing & Commissioning of 12 Core, Multi Mode, OM4 etc as complete as required and as per technical specification.

Supply, Installation, Testing & Commissioning of LC-LC, OM4 MM Patch Cord, 10 Feet 50/125.

Supply, Installation, Testing & Commissioning of 12 port LC multimode loaded LIU including pigtail as complete as required.

SITC OF UPS 60 KVA UPS WITH 30 MINUTES BATTERY BACKUP Supply, installation, testing & commissioing of 60 KVA UPS in paralleling mode at 0.99 input power factor with inbilt isolation transformer as per specification given in the document with following broad features. THD (i) shall be less than 3% in the entire loading range. UPS shall carry design output at 40 deg. Shall have soft start and hold of for incoming supply. Invertor capability to supply 150% load for 5 sec. Three Phase Input and Three Phase Output. (Input - 340V - 470V, Three Phase, 4 wire. / Output - 400-415 Volt, Three Phase, 4 Wire.) Shall not allow deep discharge of the battery and shall not go to 10.5 volts in case of 12 volt cells. Battery shall be external type with rack and suitable for 30 minute backup on 100% load. UPS shall be compatible for minimum 3 nos unit in parallel operation. (Synchronize). Parallel operation kit shall be supplied with UPS. Suitable size cable from UPS to battery bank. UPS described as above

HVAC Works Section A : VRV Equipment Variable Refrigerant Volume System Supply,Installation, Testing and Commissioning of Variable Refrigerant Volume type multi unit air-conditioning system complete with indoor and outdoor units with individual controller for cooling operations.The quoted price should include cost of all material, consumable, all taxes, labour, commissioning etc. (Make: Daikin) Outdoor Unit Supply , installation , testing and commissioning of Variable Refrigerant Volume Outdoor Unit complete with hermitically sealed scroll compressor as per following nominal capacities complete with protective coated fins, mounting frame, casing, microproccessor panel, and other standard accessories : i) Microproccessor panel , ii) First charge of refirigerant R 410A , iii) Protective coated fins iv)Mounting frame with isolation pad , all required accessories, structural support and civil foundation. v) Interconnecting Pipes for Liquit, Discharge and Suction vi) Interconnecting Cables and Earthing from nearest given point . All Inverter Scroll Compressor(s) with variable refrigeration evaporating temperature enabled feature in outdoor unit capable of inverter control with 6 pole compressor motor. The inverter compressor should be capable of changing the speed in accordance to the variation in cooling or heating load requirement, back pressure control mechanism for efficient operation in low-load condition. The outdoor unit should be fitted with low noise, aero spiral design fan with minimum External Static Pressure of 75 Pa for easy discharge of Hot air, aero fitting grille, to reduce pressure loss. The outdoor unit should be capable of automatic refrigerant charge function. The heat exchanger shall be constructed with copper tubes mechanically bonded to aluminium fins to form a cross fin coil. a) Capacity: 40 HP( Heating & cooling / Cooling only)

b) Capacity: 30 HP( Heating & cooling / Cooling only)

Double Skin Floor Mounted AHU Capacity: 20HP /6400 CFM / 30 mm wg /Backward curved centrifugal fan / Dx/ 40mm thick Double Skin with thermal isolation sandwich profile (Make: Zeco/ Edgetech/ Humidin) including AHU kit & VFD with Bypass DOL/SD Starter Panel

Supply , installation , testing and commissioning of Indoor VRV 4 - Way Round Flow Ceiling mounted cassette Type Unit with Independent Vane Control & varibale air flow as per following nominal capacities complete with i) Expansion and mixing arrangements ii) Power Supply interconnections iii) Controlling interconections iv) Piping interconnections v) Supending accessories vi) Insulated Drain pipe line vii) with wireless remote Capacity: 1.6HP

Capacity: 2.5 HP

Capacity: 4.0 HP

SITC of Refrigerant Piping For VRF System Hard drawn copper piping in brazed construciton, complete with O class nitrile rubber insulation, supports/suspenders, as per enclosed specifications. Minimum wall thickness of copper refrigerant pipes shall be as per Copper pipe-ASTM B88, L-Type standard. BRAZZING TO BE DONE ONLY WITH HARRIS USA BRAZING ROD. Approved Makes: i)Copper Refrigerent Pipe- Rajco / Maxflow / Nissan ii)Nitrile Insulation - Armaflex / K Flex / A- Flex / Superlon (i) Refrigerant Piping For Suction Gas with 19mm thick Nitrile Insulation a) Line Size: 41.3 OD

b) Line Size: 34.9 OD

c) Line Size: 28.6 OD

d) Line Size: 22.2 OD

e) Line Size: 19.1 OD

f) Line Size: 15.9 OD

g) Line Size: 12.7 OD

(ii) Refrigerant Piping For Liquid Gas with 13mm thick Nitrile Insulation a) Line Size: 19.1 OD

b) Line Size: 15.9 OD

c) Line Size: 12.7 OD

d) Line Size: 9.5 OD

e) Line Size: 6.4 OD

Vapour Barrier Mechanical Protection of Copper pipe insulation with glass cloth & UV Lag paint a) Line Size: 41.3 OD

b) Line Size: 34.9 OD

c) Line Size: 28.6 OD

d) Line Size: 22.2 OD

e) Line Size: 19.1 OD

f)Line Size: 15.9 OD

g)Line Size: 12.7 OD

h)Line Size: 9.5 OD

i)Line Size: 6.4 OD

Supply, Installation, Testing & Commissioining of Shielded control cum transmission cabling between ODU & IDU 2C X 1.0 Sqmm Cu Cable in Riggid PVC Conduit duly supported and saddled as per specification & as directed by the consultant. (note : it is important to lay one spare cable for redundancy)

Drain Piping Providing and fixing condensate drain piping with u-PVC pipe with 9mm thick nitrile tube insulation of following sizes One end on the pipe will be connected to the indoor unit of the air conditioner /AHUand the other end will be terminated to the nearest apron drain or suitable termination drain pipe complete with all fittings and support etc complete in all respect as directed by the engineer. (Supreme/Ashirvad/Astral) a) 25 mm dia

b) 32 mm dia

c) 40 mm dia

Sheet Metal Ducting Supply , fabrication & fixing of of GSS leak proof sheet metal rectangular ducting with slip on flanges as per IS 655 complete with turning vanes , companion flanges , structural support , sealing of all seams with a suitable metal sealant, completely leak proof as per drawings and as directed by the engineer. (Sail / Tata ) a) 0.60 MM (24 gauge)

b) 0.80 MM (22 gauge)

Supply and fixing of internal duct lining for duct accoustic insulation with 15mm thick Nitrile Open cell elastometric nitrile rubber applied with rubber based adhesive, screw, washer complete in all respect as specified in specifications & drawings. (Armaflex/Kflex/A Flex)

Supply and fixing of duct thermal insulation with O class nitrile insulation with factory pasted Alum foil on one side and pasted on the duct using Dendrite or equiv. adhesive. The insulation seams will be pasted with 50mm wide alum tape and PVC strapping roll strapping will be provided at 1000mm intervals. (Armaflex/Kflex/A Flex) 13mm

Supply, installation, testing and commissioning of extruded aluminium power coated 15°/30° linear continuous/descrete grills of approved shade and make

Extruded aluminium construcion, power coated with volume control damper for grils

Supply, installation and balancing of extruded aluminium power coated fresh / exhaust air louvers complete with GI dampers, GI Cowl & aluminium wire mesh birdscreen( Mapro)

Supply, installation, testing and commissioning of Alum.leaf proof Duct Damper

Supply, installation, testing and commissioning of moterised combined smoke and fire dampers made out of GI sheet of at least 120 minutes fire rating complete with GI damper of required size, smoke sensor etc as per specifications and shop drawings.

Actuator & Control panels

Supply , installation , testing and commissioning of Air Cooled Unitary Air Conditioners suitable to operate from 415+- 10% volt , 50 Hz , 3 phase power supply and consisting of hermitically sealed scroll compressor and having R22 as refrigerant . The scope of work will include initial gas charging , ODU installation on , nitrogen flushing , pressure testing and electrical connection between IDU and ODU 4 Way Cassette AC a) 1.5 Tr

c) 5.5 Tr Ductable Unitary Scroll

Supply and fixing copper refrigerant piping using bright annealed hard drawn copper refrigerant piping with 13mm thick nitrile tube insulation and GI wall fixing & ceiling suspension accessories as per site requirement complete in all respect. a) Piping for 1.5 Tr 4 way cassette ac unit copper piping with insulation.Including Electrical inter connection between ODU & IDU. Mh./Machine

b) Piping for 3.0 Tr 4 way cassette ac unit copper piping with insulation.Including Electrical inter connection between ODU & IDU. Mh./Machine

c) Piping for 5.5 Tr DUCTABLE ac unit copper piping with insulation.Including Electrical inter connection between ODU & IDU. Mh./Machine

Provinding Civil foundation to VRV Outdoor units as required

Ready made angle

FIRE FIGHTING WORKS SUB HEAD-1.0 PIPES & ACCESSORIES Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing,Wrapping and coating and cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. ( For Underground ) 150 mm. Dia

100 mm. Dia

80 mm. Dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor) 25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 50mm dia

65mm dia

80 mm dia

100 mm dia

150 mm dia

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150 mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 150 mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun Metal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 40 m

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun metal

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler

Upright Sprinkler

Horizontal side wall sprinkler

Concealed sprinkler

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 150mm dia

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 700 mm

Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.

Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required

Providing and fixing standard fireman's axe with heavy insulated rubber handle conforming to IS: 926 complete.

Providing and fixing hose BOX of size 900mmx2100mm made of 16 gause thick MS sheet with 4 mm thick frant glass doors in front painted "FIRE" in red paint i/c recessary locking /Key arrangement shall be painted with one coat of primer & two coat of finished stove enameled post office red colour paint .

Providing and fixing 25 mm dia inspection & testing assembly with gun metal ball valve, gun metal sight glass ,Reducer ,union, G.I PIPE. connection to drain pipe/riser.

Providing & fixing cast iron 100 mm dia. Foot valve with nuts, bolts, 1.5 mm thick CAF gasket complete with all accessories (To be provided into UG Fire Water Tanks).

Supply and fixing of 4 Nos G.I round bottom FIRE BUCKET of 9 LTR. Capacity field with sand including proper supporting /mounting arrangement MS Angle Iron Frame painted by fire red colour over 2 coats of red oxide paint and written with white paint FIRE complete in all respects as per direction of Engineer Incharge .

SUB HEAD-2.0-FIRE EXTINGUSHER Providing, storing, handling, shifting, installation, testing and commissioning of halon free portable fire Extinguishers as described below: Concealed work, including cutting chases and making good the walls etc. 4.5 kg carbon dioxide extinguisher, IS marked, with high pressure discharge tube, horn, control valve, CCE approved cylinder.

6 kg Mono Ammonium Phosphate (ABC) type cartridge operated extinguishers.

Providing and fixing 2 kg capacity clean agent-HFC 236FA Stored Pressure type fire extinguisher ISI marked under IS:15683 complete with imported Novec 1230 manufactured by 3M, with Zero Ozone Depeltion Potential and Very Low Global Warming Potential of 1 with 20 Years Blue Sky Warantee against any regulatory Bans and Restrictions.

Providing and fixing Fire related signages printed on photoluminescent U1000 aluminium sheet of 1.0 mm (+-10%) containing Lumigen II as base chemical, covered under UV stablized coating and of appropriate size including fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc.

Sri Mrinal Saikia