PERIODICAL SERVICES TO CERTAIN OTM AND MARRIED ACCN AT SI LINES UNDER GE BHOPAL

Amount

Note : 1. Contractor will deposit the requisite quantity of Distemper, Exterior weather coat paint, and other materials with Original Purchase Voucher, Manufacturers Test Certificate (As directed by Engr-in-Charge) required for the work within fifteen days from the date of commencement of the work. The paint will be issued to the contractor as and when required for carrying out the work at site which will be signed by contractor or his rep and Engr-in-Charge. 2. Mixing of oil bound distemper, exterior/interior emulsion paints etc shall be carried out with mechanical mixer/stirers. 3. Surface shall be allowed to dry completely before application of any paint. Wet or newly plastered surfaces with visible moisture shall not be painted till it is dry. 4. The rate quoted against BOQ are including necessary scafolding expences upto triple storey buildings.

M&L for preparation of old treated surfaces of walls including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and stopping nails marks by putty and applying one coat of white wash complete all as specified and directed.

M&L for preparation of old treated surfaces of ceiling including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and stopping nails marks by putty and applying one coat of white wash complete all as specified and directed.

M&L for complete removal of old decorated surface of walls and applying two coats of oil bound emulsion distemper white/tinted over and including 1mm thick coat of white cement based putty, finished even and smooth complete all as specified and directed.

M&L for preparation of old painted surfaces of walls and applying one coat of oil bound distemper including window & door jambs, cills, cornices etc complete all as specified and directed.

M&L for preparation of old painted surfaces of walls and applying one coat of cement based paint including window & door jambs, cills, cornices etc complete all as specified and directed.

M&L for preparation of old treated wood or wood based surfaces of any description, exceeding 10 cm width or girth and applying one coat of synthetic enamel paint of approved shade complete all as specified and directed.

M&L for preparation of old treated steel or iron surfaces of any description, exceeding 10 cm width or girth and applying one coat of synthetic enamel paint of approved shade complete all as specified and directed.

M&L for complete removal of old decorated surface of walls and applying two coats of exterior weather proof emulsion paint of 100% premium acrylic emulsion paint on old prepared surfaces of walls including chajja, patta etc. having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, water, alkali & fungal resistance, dirt resistance of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including 1mm thick coat of white cement based putty, finished even and smooth complete all as specified and directed. complete all as specified and directed.

M&L for preparation of old painted surfaces of walls and applying one coat of exterior weather proof emulsion paint of 100% premium acrylic emulsion paint including chajja, patta etc. having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, water, alkali & fungal resistance, dirt resistance of required shade with silicon additives @ 1.43 litre/ 10 sqm complete all as specified and directed.

M&L for complete removal of old decorated surface of walls and applying two coats of interior plastic emulsion paint, white/tinted over and including 1mm thick coat of white cement based putty, finished even and smooth complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls and applying one coat of interior plastic emulsion paint, white/tinted complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceiling and applying one coat of interior plastic emulsion paint, white/tinted complete all as specified and directed.

M&L for high class french polishing on wooden surfaces of any description, width or girth including cleaning, preparing the surface and applying a coat of wood filler as required to achieve glossy finish complete all as specified and directed.

M&L for ShaliCryl ® 215 single component, UV resistant, unique elastomeric, high build exterior water proof coating based on a revolutionary acrylic polymer with quick-set capabilities to resist moisture attack with and including comprising of following stages:- (a) Surface Preparation:- Removing all loose and foreign materials, if any by washing with a jet of air / water, repairing structural defects before application of ShaliCryl ® 215, filling voids and undulation area with polymer mortar made out of Shali SBR latex, water, cement and sand in the ratio of 1:1:5:12.5, filling cracks up to 3 mm with Plasti Seal and cracks over 3 mm with Plasti Seal P after opening the crack to 'V' cut including damaged poor plaster surface in old building shall be removed and re-done with new cement & sand in the ratio of 1:4 admixed with ShaliPlast LW+ @ 200 ml / bag of cement. (b) Primer Application:- Applying ShaliPrime WB as Primer after dilution with potable water in the ratio 1:0.5 for a theoretical coverage 8-10 sqm/ lits of the mix and allow it to dry for 3-4 hrs. post elimination of undulation, roughness of concrete, joint marks, voids and any other surface correction. (c) Application of Material:- Applying first coat of ShaliCryl ® 215 over the primed surface @ 160 ml / sqm, adding maximum of 10% potable water by volume for the first coat only, if required, to have brushable consistency only and then allow the applied coating to dry 6-8 hrs after application and finally applying second coat of ShaliCryl ® 215 without dilution over dried first coat @ 140 ml / sqm and allow it to dry and let it dry for 72 hrs and applying a coat of 100 micron of ShaliCryl TC 100. (d) Make: Specifications here in before are considered from STP make but the contractor can provide similar materials of any other make as specified in approved list of makes.

Taking down plants/vegetable growth (upto 10cm girth) from buildings walls, parapets by cutting/ chiseling fully without disturbing structure upto height of 10.00 m from ground level at different locations and cleaning the surfaces neatly with wire brush to remove all dust and other foreign particles and applying hydorochloric acid (HCL) on left over root portion and making good the disturbed surfaces in cement mortar 1:4 complete all as specified and directed.

Taking down cement plaster of any description on brick/stone walls, concrete surfaces etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar 1:6 on any face of brick walls/stone surfaces, finished even and smooth without using extra cement in patches complete all as specified and directed

M&L for rendering 5 mm thick in cement mortar 1:3 on brick/ concrete surfaces of ceilings, finished even and smooth wthout using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick rendering in cement mortar 1:4 on any face of brick walls/concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of oil emulsion distemper, white/tinted over and including 1mm thick coat of white cement based putty, finished even and smooth complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of exterior weather proof emulsion paint of 100% premium acrylic emulsion paint on old prepared surfaces of walls including chajja, patta etc. having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, water, alkali & fungal resistance, dirt resistance of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including 1mm thick coat of white cement based putty, finished even and smooth complete all as specified and directed.

M&L for preparation of newly plastered surface of ceiling and applying three coats of white wash complete all as specified and directed.

S&F of chicken wire mesh, mild steel of 12mm mesh size and 0.56 mm dia of wire and fixed with nails complete all as specified and directed.

M&L for crack filling with approved crack filling compound of approved make, crack thickness more than 3 mm; with and including opening of cracks, cleaning, and necessary scaffolding suitable for height upto 10.00 mtr from ground level complete all as specified and directed.

Hacking out old broken glass (any thickness, quality or description) from wooden/ steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F of 3.0mm thick plain sheet glass, ordinary quality and glazing with oil putty in area n exc 0.50 Sqm each pane complete all as specified and directed.

S&F of 4.8mm thick plain sheet glass, ordinary quality and glazing with oil putty in area n exc 0.50 Sqm each pane complete all as specified and directed.

S&F in repairs stainless steel wire cloth with 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed to frames with screws complete all as specified and directed.

M&L for preparation of old plastered or concrete surfaces of any description, exceeding 10 cm width or girth and applying one coat of synthetic enamel paint of approved shade complete all as specified and directed.

SULTAN SINGH, CONTRACTOR (BID ID -3226721)

Samaksh Enterprises (BID ID -3227106)

JYOTI ENTERPRISES (BID ID -3232458)