Construction of toilet block and civil renovation works in Manohar C Wasta stadium and Renovation of Hockey ground and Toilet Block at IIT Madras Campus

Amount

CIVIL WORKS

Dismantling barbed wire or flexible wire rope in fencing including making rolls and stacking within 50 metres lead.

Dismantling and stacking within 50 metres lead, fencing posts or struts including all earth work and dismantling of concrete etc. in base of R.C.C

Dismantling and stacking within 50 metres lead, fencing posts or struts including all earth work and dismantling of concrete etc. in base of T’ or ‘L’ iron or pipe

Deduct cost of old steel section / MS grill etc.,

Disposal of building rubbish / malba / similar unserviceable, dismantledor waste materials by mechanical means, including loading, transporting, unloading outside the IITM premises including approval from local authorities like municipality / corporation complete and as per the direction by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. Necessary deduction for voids of 20% will be made from the actual measured vehicle volume of materials.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth upto 200 m lead and for all lift, as directed by Engineer-in-Charge. All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm in depth : consolidating each deposited layer by ramming and watering, lead up to 200m and for all lift.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases for columns

Centering and shuttering including strutting, propping etc. and removal of form work for :Columns, piers, abutments, pillars, posts and struts

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1 : 4 : 8 (1 cement : 4 coarse M-Sand : 8 graded stone aggregate 40mm nominal size)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works upto plinth level Concrete of M35 grade with minimum cement content of 370 kg /cum.

Providing and laying in position ready mixed or site batcheddesign mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works above plinth level upto floor V level Concrete of M35 grade with minimum cementcontent of 370 kg /cum

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work ready to use “cut and bend” rebars of approved make from factory/workshop to construction site including placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with Fly ash concrete blocks of class designation M10 in foundation and plinth in ;Cement mortar 1:6 (1cement :6 coarse M-Sand)

Providing and fixing NSF Orion fencing panel grey colour of size 2.44x1.56m, vertical strand post 1.66 ht fixing with M-12 nuts, bolts and washers including strengthening as required complete as per the direction of Engineer-in-charge.

Dismantling of weld mesh including removal of welded flats,angles and stacking within 50 metres lead.

Dismantling roofing including ridges, hips, valleys and gutters etc.,and stacking the material within 50 metres lead of G.S. Sheet

Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar

Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge

12 mm cement plaster of mix 1:4 (1 cement: 4 fine M-sand)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only .Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size Size of Tile 600 x 1200 mm

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.1.00 mm thick with zinc coating not less than 275 gm/m²

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing.30 mm thick pre laminated PVC door shutters

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 453x357 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.(Concealed work, including cutting chases and making good the walls etc) 25 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work 25 mm nominal dia Pipes

Providing and fixing wash basin with C.I. brackets, 15 mm PTMT pillar cock, 32 mm PTMT waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm PTMT pillar cock.

Providing and fixing wash basin with C.I. brackets, 15mm CP brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls whereever required. White Vitreous China Flat back wash basin size 550x 400 mm with single 15mm CP brass pillar taps

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.

Providing and fixing PTMT urinal cock of approved quality and colour.15 mm nominal bore, 80 mm long, 42 mm high and 30mm wide with BSP female threads weighing not less than 48 gms

Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2" BSP thread and shapes, weighing not less than 60 gms.

Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing PTMT bib cock of approved quality and colour. 15mm nominal bore, 86 mm long, weighing not less than 88 gms

Providing and fixing PTMT angle stop cock 15 mm nominal bore,weighing not less than 85 gms

Supplying and fixing PTMT Health faucet -15mm dia of Prayag or equivalent make as approved by the Engineer-in-charge

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing PTMT stop cock of approved quality and colour.20 mm nominal bore, 89 mm long, weighing not less than 88 gms

Providing and fixing PTMT grating of approved quality and colour.Circular type

100 mm nominal dia

125 mm nominal dia with 25 mm waste hole

Providing and fixing unplasticised P.V.C connection pipe with PTMT Nuts, collar and bush of approved quality and colour.15 mm nominal bore with 45 cm length

Providing and fixing PPR Unions PPR Union 20mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler 110 mm

Single pushfit Coupler

Single tee with door 110x110x110 mm

Single tee without door 110x110x110 mm

Bend 87.5° 110 mm bend

Shoe (Plain) 110 mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm

Supplying and fixing GI base clamp of all size (galvanised) for laying/ fixing pipe lines of various diameter on walls, the rate inclusive of necessary U- clamp for fixing pipes, acnchour fastner for fixing the clamp etc complete. The measurement will be made based on the actual weight of the clamp and necessary bolt.

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete 25 to 40 mm nominal bore

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 25mm nominal bore, weighing not less than 62 gms

Providing and fixing square-mouth SW gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight FRC cover LD with frame of 300 x300 mm size (inside) as per standard design 150 x 100 mm size P type With fly ash concrete block of class designation M10

Constructing brick masonry chamber with bricks in cement mortar 1:4 (1 cement : 4 coarse M sand) FRC cover-MD - 10T with frame of size 450x450 mm internal dimensions, R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse M sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 coarse M sand : 10 graded stoneaggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse M sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design Inside dimensions 600 x 600 mm and 45 cm deep for pipe line with one or two inlets With fly ash concrete block of class designation M 10

Extra for depth beyond 45 cm of brick masonry chamber For 600 x 600 mm size With fly ash concrete block of class designation M 10

Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including uPVC drain pipe 110 mm diameter and 1.20 m long complete as per standard design.

Supplying and installation of Sandwich PUF panel / block of 80mm thick confirm to best International / Indian Standards. Density : 40 +2 Kg / M 3 (PU) Closed cell content : 90 – 95% Temperature range : - 100o C to + 90 o C Water absorption : < 1% K factor : 0.22 U factor : 0.019 – 0.022 Self Extinguishing : As per ASTM D 1692 The materials, both PUF block and Panel should be fire resistant and should have excellent self-extinguishing characteristics. The bidder has to specify the fire resistant characteristics of the material. Both side of panel elements are made up of 0.5 mm thick hot deep galvanized and pre-painted steel sheets. The color coating should be of approved color at least 25 micron silicon polyester on 120 gms / m 2 of Zinc coating. The steel sheets should have formed grooves to provide extra strength as well as to enhance the appearance of cladding. The panel should be manufactured by pressure injection of CFC free Poly urethrene foam at 40 +2 Kg/m 3 density, in between the outer and inner steel sheet surfaces. The wall panels either be complete with tongue and groove joint together or Cam Lock joint with flushing. The Cam Locks should be of G.I /PVC material and minimum of 0.7 mm thick. The rate inclusive of channel and all necssary fittings required to provid in top and bottom of the partition to support the PUF panel etc., complete. The bidder should provide the manufacturing certificate conforming to CFC free method of manufacturing and paint & zinc coating thickness. The rate inclusive of necessary fixters for installation of partition, selaing the joints with PU/ Silicon selant etc., complete.

Structural steel work in single section fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer (Zinchromite yellow primer) all etc. complete

Supplying and filling in plinth with M-Sand under floors including watering, ramming, consolidating and dressing complete

Supplying and fixing LDPE black color sheet of 400 microns thick for laying the concrete.

Providing, driving with hydraulic piling rigs with power units and installing driven cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of shoe and the length of pile to be embedded in the pile cap etc. all complete. (Length of pile for payment shall be measured from top of shoe to the bottom of pile cap) :450 mm dia piles

Brick work with Fly ash concrete blocks of class designation M100 in foundation and plinth in Cement mortar 1:4 (1cement :4 coarse sand / M sand)

Add Extra for brick work with Fly ash concrete blocks in superstructure above plinth level up to floor V level

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand/ M-Sand)

12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Labour charges for dismantling and removing the existing water closet including debris cleaning up to lead of 50m lead.

Labour charges for dismantling old wash basin with bracket, urinal basin with clamps flush tank with clamp / bracket (both low and high level tank), old E.W.C / I.W.C with traps, G.I pipes, fittings and taps in old toilet, etc and stacking the material. ((Parryware / Hindware/ Somany)

Labour engagement for unmeasurable items of works such as masonry touch up works, cleaning works, machinery, lab equipment and materials shifting to enable taking up the renovation woks as per the direction of Engineer in charge. Helper / Cooliee

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Supplying and applying ( MIXGUARD HR-5 or equivalent product of SIKA/ FOSROC/ BASF) cold applied elastomeric water proof membrane over the prepared surface, prepare a base surface stabilizing primer (MIXPRIME AC100 @ 2 : 1 : 3 (MIXPRIME AC100 : WATER : OPCEMENT) and apply directly (@ 1KG/SQM) along with MIXMAT GFM-50 at an overlapping of 50mm minimum After a curing period of 3-4 hours prepare and apply MIXPRIME AC @ over at a consumption of 250ML/SQM. After curing of 3-4 hours apply a coat of MIXGUARD HR – intermediate elastomeric water proof coat at consumption of 0.5KG/SQM. After a curing time of 4-5 hours apply MIXGUARD HRXtra - Micro fibre reinforced high tensile top coat at consumption of 0.5KG/SQM. Leave 72 hours time for complete system curing. Total build up DFT of the system will be 1700 microns.

Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge. Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2). 25 mm average thickness in 2 layers.

Providing polymer modified coving floor wall junctions using CM 1:4 admixed with Nito bond AR / SBR @ 1.5 lts per bag of cement complete as per the manufacturer's specifications

Cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - incharge.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.

Grouting the tile joints with Laticrete products- Applying Latapoxy SP100 (Grouting of tiles to be done with MYKL Laticrete Latapoxy Sp100 stainfree grout as per the methodology specified in the technical data sheet of MYKL. 3mm width & 12mm depth grout to be provided between tiles to fill the joints. 1 Unit = 5 Kgs. Coverage: 24.53Sq.mt. per Unit ) in the tile joints. The rate inclusive of surface preparation, labour, material, tools and plants etc complete.Rate inclusive of materials, labour charges at all levels. For tile size 60x60cm

Providing and fixing Urinal partition of size 450mm W x 1200mm H x 12mm thick compact laminated color of HPL board Suede Finished with SS bracket of approved quality and manufacturer specification etc complete as per the direction of Engineer in charge

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 25 mm nominal dia Pipes

Providing and fixing of PVC pipe of SWR grade - 160mm / 6 kgcm2 with necessary couplings, solution and special clamp as per approved make Prince / Finolex or Equivalent ISI Make etc. complete

Making connection of drain or sewer line with existing manhole including breaking into and make good the walls, floors with cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand / M sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with Cement mortar 1 :3 etc – complete. For pipes 100 to 250 mm diameter

Providing Mechanical core cutting up to 300mm depth 75 to 150mm dia for fixing pipes air cleaning for cutting holes removing of debris and labour charges etc.., complete

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red. Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer- in-Charge. Granite work

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non- decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing and fixing the Sunmica / laminated sheet 1mm thick for cupboard shutter & cupboard work including cost of labour charges for fixing including providing teak wood beading of 19x6mm (if needed) all-round etc complete as directed.

Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing of decorative Teak wood beading for wall panelling of size 20mm x 6mm including polishing etc. complete as per direction of Engineer in charge.

Providing and fixing of 8mm thick Modi float/ Saint Gobain make Mirror with bevelled edges/ edge moulded and fixing the same on wall with SS stud of required number etc.,

Providing and fixing white vitreous extended wall mounting water closet of Hindware make Model-Italian collection-Venice (Cat No-92509-S-30 Water Closet, Seat cover with attached ceramic flushing cistern white colour) of size 64x36x73 Cm and approved shape with necessary fittings, nuts, bolts and gasket etc complete as per the direction of Engineer in charge.

Providing and fixing white vitreous china water closet squatting pan (Indian type). Orissa pattern W.C. Pan of size 580 x 440 mm.

Providing and fixing low level flushing cistern with manually controlled device (handle lever) confirming to IS : 7231, with all fittings and fixtures complete 10 lt. capacity - white

Providing and fixing White vitreous china flat back half stall urinal of size 580x380x350mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required: Single half stall urinal with 5 litre P.V.C. automatic flushing cistern.

Providing and fixing of Metro / Equivalent CP brass urinal spreader including necessary screws and 'M' Seal filling etc complete as per direction of Engineer-in charge

Supplying and fixing DORMA SILVER Door closer of TS 89 EN 3/4 with Std. arm, closing force adjustment from side, closing speed and latching action.

Providing and fixing Dorma make heavy duty Mortice lever handle lock (Model No-952F) with 90 Euro profile cylinder both side key model for doors etc complete., as per the direction of Engineer in charge.

Providing and fixing DORMA XL-C Dead lock (heavy duty) with special accessories for aluminum or glazed door with necessary fittings & labour etc complete.,

Providing and fixing door handle finishes of SS (Neki make butterfly type) and making holes in doors with necessary fittings & labour etc complete. Size-300mm long and 20mm dia

Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion,necessary brass screws etc. to suit shutter thickness complete

Supplying and fixing CP brass two-way bib cock with flange of ( Hindware make Model- Fluid, Cat No-F360005) approved by the Engineer-in-Charge of 20mm dia nominal bore etc complete

Supplying and fixing CP brass Angular stop cock with flange of ( Hindware make Model- Fluid, Cat No-F360006) approved by the Engineer-in-Charge of 20mm dia nominal bore etc complete

Providing and fixing of CP Health Faucet in Metro make including all necessary fittings etc. complete

Supplying and fixing CP brass Pillar cock of ( Hindware make Model- Element, Cat No-F360001) approved by the Engineer-in-Charge of 20mm dia nominal bore etc complete.

Providing and fixing of stainless steel matt finished wall mounted Foldaway grab bar for Physical challenged safety handle of size 35x760mm long VIKING or equvalent.

Providing and fixing of 40mm thick CP Brass waste Couplings for approved make and etc. complete

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40 mm dia

Providing and fixing unplasticised PVC connection pipe brass unions (Kohinoor) 90 cm length 15mm nominal bore

Supplying and fixing CP Cockroch trap for the size of 125x125mm of Jaguar make including fixing in position etc complete.

Cutting holes up to 30x30 cm in walls including making good the same: 18.76.1 With common burnt clay F.P.S. (non modular) bricks

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 25 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 50 mm nominal bore

Providing and fixing CPVC union in CPVC pipes including cuttings and threading the pipe and making long screws etc, complete (New work) - 25mm nominal bore. (Finolex / Astral)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 40 mm nominal dia Pipes

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter

Providing and fixing of 20mm dia extension nipple with a length of 50 to 75mm with necessary fittings etc., complete as per direction of engineer in charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 75 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5°. 75 mm bend

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 100 mm diameter S.W. pipe

Providing and fixing on wall faced unplasticised - PVC moulded fitting / accessories for unplasticised - Rigid PVC rain water pipe Bend 87.5 degree 160 mm dia

Providing and fixing on wall faced unplasticised - PVC moulded fitting / accessories for unplasticised - Rigid PVC rain water pipe Shoe (Plain). 160 mm shoe

Constructing masonry chamber 60 x 60 x up to 100 cm, inside with 100 class designation flyash concrete block brick work in cement mortar 1:5 (1 cement : 5 fine sand / / M sand) for sewer line intersections and top cover with SFRC cover with frame of approved grade, necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand / M sand : 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand / M sand) 12mm thick finished with a floating coat of neat cement complete as per standard design. With flyash concrete blocks class designation 100

Providing and fixing unplasticised PVC pipe, clips of approved design to unplasticised - PVC rain water pipe by means of 50 x 50 x 50 mm hard wood plugs. 160 mm

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required and scaffolding etc., complete.

Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Crimp curve

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand / M sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in- Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Polishing of Kota stone flooring/ marble flooring/ mosaic flooring etc by grinding and honing of floor using diamond abrasives to remove all minor scratches to bring an even surface. Later hardening the surface with floor polishing powders. The floor will be burnished with 1200 RPM burnishes.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.

Applying super premium quality 100% Exterior Acrylic (Asian / ICI /Berger / Nippon / Nerolac) emulsion : (Fresh work including complete scraping / surface preparation, as appropriate base (primer) coat and top two or more coats). Applying exterior paint of approved colour, make, brand and surface coverage of painting as per the manufacturer specification. The exterior paint shall be applied over dry surface after complete scraping and removal of all loose or defective paint or powdery residue using mechanical methods with Zero dust vaccum technology followed with High pressure Jet washing and sealing the surface with necessary exterior base coat or primer before application of top coat of exterior paint. The contractor shall also carryout necessary surface preparation including removal of loose plastering, patch plastering, crack filling, micro-concreting, application of damp proof coating and making good the wall surface etc wherever required before applying base or primer coat. The contractor should ensure complete covering of floors using tarpaulin / plastic sheet while taking up the work. The rate quoted shall be inclusive of charges towards all labour, material, transport, scaffolding, safety arrangements, Personal Protective Equipments (PPE), tools and plants etc but excluding the cost of waterproofing, attending to leakages and major civil repair works if any. The Paint manufacturer shall inspect the work in every stage, submit inspection / field test report, certify the product / application and give 10 year Guarantee.

Interior painting: (two or more coats over a primer coat including complete scraping, other surface preparation like removal of loose paint residuals, damaged plastering, repairs to plaster, white cement based (JK / Birla) touch up putty / primer and making good the wall surface etc) Applying interior paint of approved colour, make, brand and product at the approved rate of surface coverage of painting as per Annexure A.1.3. The interior paint shall be applied over dry surface after complete scraping and removal of all loose or defective paint or powdery residue using mechanical methods with Zero dust vaccum technology followed with sealing the surface with a coat of approved interior primer before application of top coat of exterior paint. The contractor shall also carryout necessary surface preparation including removal of loose plastering, patch plastering, crack filling, micro-concreting, application of damp proof coating and making good the wall surface etc wherever required before applying primer coat. The contractor should ensure complete covering of floors using tarpaulin / plastic sheet while taking up the work. The work shall be executed as per the detailed specifications and special conditions mentioned in the Annexure 1. The rate quoted shall be inclusive of charges towards all labour, material, transport, scaffolding, safety arrangements, Personal Protective Equipments (PPE), tools and plants etc.

Enamel painting for doors / windows / wall panels (two or more coats including a coat of primer) on both exterior and interior surface of wooden and steel joineries using approved colour, make and brand of synthetic enamel paint two or more coats over a coat of primer as per Annexure A.1.4. (Top coat enamel coverage not less than 8.83sqm per litre for two coats over a coat of primer as per manufacturers specifications). The contractor should ensure complete covering of floors using tarpaulin / plastic sheet while taking up the work. The work shall be executed as per the detailed specifications. The rate quoted shall be inclusive of charges towards all labour, material, transport, scaffolding, safety arrangements, Personal Protective Equipments (PPE), tools and plants etc. (Asian (Premium Gloss Enamel) / Berger Luxol High Gloss Enamel / / Nippon Hi Gloss Enamel).

Exterior painting: (two or more coats on old work). Applying exterior paint of approved colour, make, brand and product at the approved rate of surface coverage of painting (As per Annexure A.1.1). The exterior paint shall be applied over dry surface after complete scraping and removal of all loose or defective paint or powdery residue using mechanical methods with Zero dust vaccum technology followed with High pressure Jet washing and sealing the surface with necessary exterior base coat or primer before application of top coat of exterior paint. The contractor shall also carryout necessary surface preparation including removal of loose plastering, patch plastering, crack filling, micro-concreting, application of damp proof coating and making good the wall surface etc wherever required before applying base or primer coat. The contractor should ensure complete covering of floors using tarpaulin / plastic sheet while taking up the work. The work shall be executed as per the detailed specifications and special conditions mentioned in the Annexure 1. The rate quoted shall be inclusive of charges towards all labour, material, transport, scaffolding, safety arrangements, Personal Protective Equipments (PPE), tools and plants etc but excluding the cost of waterproofing, attending to leakages and major civil repair works if any. The Paint manufacturer shall inspect the work in every stage, submit inspection / field test report, certify the product / application and give 10 year Guarantee

Providing and fixing Aluminium composite panel of 4mm thick ( M/s Virgo or equivalent) for roofing / cladding. The ACP shall be fixed over the frame work made out of Aluminium box sections or steel section with adequate support and fixed to the frame using Anchor fasteners together with necessary screws and bolts and nuts and the grooves shall be sealed with Silicon Sealant etc. complete as directed by the Engineer-in-charge. (Cost o the frame shall be paid separately).

E-VERVE DESIGN

CREATORS ENGINEERS AND INTERIORS PVT LTD