Construction Of GST Building For State Tax Joint Commissioner Administrative,Hazaribag

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item - A0 and disposal of excavated earth as obtained to a distance upto 50M including all lifts levelling, ramming the foundation trenches, removing roots of trees, shurbs all complete as per approved design, building specification and direction of E/I.

Extra for earthwok in hard soil as per specification and direction of E/I. (Vide classification of soil item - B).

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume)

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed fully compacted and fine dressed with earth obtained after cutting within a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I. (Mode measurement compacted Volume).

Providing coarse clean Sand in Filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing designation 75B brick work in C.M. (1:6) in foundation and plinth approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 75 B work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints of screening materials, scaffolding, ranking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in foundation and plinth with approved uality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Extra for brick work for each consecutive floor above first floor including watering and scaffolding, all complete as per direction of E/I.

2nd Floor

3rd Floor

Providing designation 112mm thick reinforcement designtion 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:4) in supertructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including cost of screening materials scaffoliding raking out joints to 15mm depth curing taxesand royalty ( but excluding theb cost of reinforcement) all complete as per building specification and direction of E/I.

Providing and laying position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level.

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 40mm nominal size)

1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)

1:3:6 (1 cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 40mm nominal size)

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20mm nominal size).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to Plinth Level- 1:1.5:3 (1 cement ; 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string course, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reionforcement : (1:1.5:3 (1 cement : 1.5 : coarse sand (zone-III) : 3 graded stone aggregate 20mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15" landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, fotting, bases of columns, etc. for mass concrete

Suspended Floors, roofs, landings, balconies and access platform

Lintels, beams, Plinth beams, girders, bressumers and cantilevers

Column, Pillars, Piers, Abutments, Posts and struts

Stairs, (Excluding landings) except spiral-staircases

Weather shade, Chajjas, corbels etc. including edges

Supplying, fitting & fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with aluminum fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I.

S/F 35mm thick solid core type non - decorative double leaf flush shutters in door and windows with black board core blended with high quality phenol formal dehyde synthetic resin both side comercial venerred of started make make with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand direction of E/I

Providing Toe steel reinforcement of following dia rods as approved design and drawing excluding carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (Only Valid for SAIL, TATA Steel, JSPL, Electro Steel Ltd. and Vizal Steel)

12mm to 16mm

Supplying, fitting & fixing M.S. GRILL made of 20 x 6 mm flat / 12 mm square bar as per approved design and drawing properly fabricated with joints continuous fitted, welded and finished smooth, hoisting as per building specification and direction of E/I.

Providing and fixing fan hook of 16mm dia M.S. bar 1 metre long bent to required size and shape, placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/I, (where materials is not supplied by deptt.)

Supplying, fitting and fixing Collapsible Gate of approved size and make properly fabricated with vertical double channels 20x10x2mm. at 100mm center and braced with M.S flat diagonals 20x3mm, with top an bottom rails of t. Iron 40x40x6mm with 38 mm dia steel pulleys complete with bolts, nuts, locking arrangements stoppers, handles, including and taxes all complete as per building specification and direction E/I.

Supplying, fitting and fixing fully glazed steel door. Windows or ventilations of standerd rolled "z" and mullion steel sections and size as per IS - 1038 joints met and welded with 100x16x3mmM.S lugs fixed in cement concrete (1:2:4) blocks 15x10x10cm , size including coast of oxidised iron fitting, with hinges, handle per steps , catch springs , 3mm thick plain glass with Aluminium beads and inner frame fixed with lugs with 20mm longs 6.3mm G.I counter sunk macine screw and nuts and appling a coast red lead paint carrige to work site hoisting and placing in position in all storts and taxes all complete as per building speciffication and direction of E/I.

Providing designation 75B one brick flat soling joints fitted with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing and laying 15mm to 23mm thick kotah stone tiles in risers of step , skirting and pillars of approved size texure and colour laid over 12mm thick cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing to granolilthic finish with approved quality of carboarandom stone including cost of curing,taxes and royalty all complete as per specification and direction of E/I.

Providing and laying Double charge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622/ISO 13006 of approved make in all colours and shades laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement alurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. complete Size of Tile 600 x 600 mm

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:4) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Extra for plaster work over exterior surface for each consecutive floor above first floor including cost of scaffolding etc. all complete as per direction of E/I.

2nd Floor

3rd Floor Qty.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 1.5mm cement punning including curing, carraige of water with all leads and lifts as per building specification and direction of E/I.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required scaffolding, washing of floor and taxes all complete as per building and specification of E/I.

Providing two coats of snowcem shade and makeover a coat of cement of primer on new surface including prepring the plastered surface smooth with sand paper , soaping, curing and taxes and royalty all complete as per specification and direction of E/I.

Providing two coats of synthatic enamel paint over a coat primer of approved shade and make over new wooden surface after cleaning removing dirt scale smoke, grease and sand paperring including coast of scaffolding and taxes all complete as per specification and direction of E/I.

Providing French spirit polishing over new wooden surface to give desired texture and gloss with approved make and shade of ready mixed French polish including cleaning the surface after removing dirt, Scales, grease and sand preparing, including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specificatio).

Providing two coats of painting with ready mixed paint of approved shade and make over steel surface including cleaning the surface througly coast of scaffolding and taxes all complete as per specification and direction of E/I.

Providing two coats of synthetic enamel paint of apporoved shade and make over steel surface thoroughly scaffolding and taxes all complete as per building specification and direction of E/I.

Providing 250mm wide brick drain in cement mortar (1:6) with as. 150mm clear depth and 250mm apron including cost of earthwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

Water proofing for old and New Roof Slab : - Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible material applied with brush, roller or spray for water proofing coating as per manufacturer specifications with following steps:-

Surface preparation :- Providing and cleaning of concrete surface to remove dust, oil, grease including removal of existing loose paint/coating and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete Ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage, leakage. On identification of seepage, cement grouting to be done with non shrink expanding admixture of Sika India Pvt. Ltd/MYK schomberg/Dr. Fixit/fosroc or equivalent. Proiding and reparing of all corners and joints such as those between the parapet wall and the roof slab etc. shall be chamfered with 150mm x 150mm fillet of mortar (Cement sna - 1:4) admixed with acrylic polymer of Sika/Fosroc/MYK Schomberg/Dr. Fixit or equivalent.

Before chamfering surface irregularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modified repair mortar including a coat of bonding agent of the same with cement slurry including all material, labour, tools complete.

1st coat :- Apply 1st coat of two component acrylic modified, ready to use, flexible cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600mm by brush or roller. After 1st coat of application, 45 gsm of fibre glass cloth to lay when the first layer is still green, 1st coat should be applied @ 1.50 kg/sqm/coat. For the purpose of measurement the entire treated surface will be measured.

2nd Coat :- To apply the 2nd coat of two component acrylic modified, ready to use, flexible cementitious material right angle to the 1st coat over the glass fibre laid surface. 2nd coat should be applied @ 0.7 kg/Sqmt/coat. For the purpose of measurement the entire treated surface will be measured. After three days of drying the 2nd coat, the rain water outlets to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectification to be doen as per satisfaction of E/C. The waterproof coating to be protected from damage before screed over it. Water proofing coating to be protected from damage before screed over it. Water proofing Brand-Sika Topseal 109hi/Fosroc Brushbond RFX/Dr Fixit Pidifin 2K/MYK Auafin TG, Product Performance - chemical

Base part A : Acrylic copolymer, Part B : Specially graded cementtitious powder - Density 1.6 kg/l (mixed density) at +270C Tensile strength ~ 2N/mm2 after 28 days (with Fibre cloth) (according to ASTM D 2370) Pullout Bond Strength ~ 2 N/mm2 (concrete failure) (According to ISO 4624) Slant-shear bond strength~4 N/mm2 (According to FIP 5.15) Elongation at Break ~ 35% without Fibre Cloth and 20% with fibre cloth (According to ASTM D 2370)

Protection of treatedsurface with PCC : - The treated surface should be covered with 25mm/50mm PCC of M-20 grade (1:1.:3) with proper slope (1:120) towards the rain outlets in alternatepanels of 2 Mt x 2mt keeping 6mm gap between the panel joint intergal water proofing admixture conforming to IS 2645 @ of 100 ml per bag of cement to be added in the acreed concrete (paid separately for this items) all corners shall be chamfered with 150mm x 150mm fillet. The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - the peripheral gaps between PVC pipe outlet and concerte surface should be packed properly with rich concrete and the peripheral mouth to be sealed with moisture insentive epoxy putty of Sika India pvt Ltd/MYK Schomberg/Dr. Fixit/Fosroc. For the purpose of measurement the entire treated surface will be measured."

Groove of PCC surface should be filled with Polysulphide Sealant. (Paid Separately) Brand - Sika India Pvt. Ltd./MYK Schomberg/Dr. Fixit/Fosroc. Warantly for five years.

Covering of treated surface with PCC :- Providing 50mm thick cement concrete M-20 (1:1.5:3) maintaining slope in alternate 2 mt x 2 mt panels with approved quality of stone chips of 20mm to 6mm size graded and cleaned sand of F.M. to 3 including screening, shuttering and mixing cement concrete in mixer with admixture in integral water proofing and placing in position, skirting curing, taxes and roaylty all complete as per building specification and directions of E/I. Panels that has been left should be casted next day. There should be 6mm gap between Panels Brand-Sika-plastocrate plus, MYK proof WP 10, Fosroc-Conplast X 4211C, Dr. Fixit Pidproof LW+ or equivalent.

Providing and filling of 6mm thick Groove between 50mm PCC Panels with 6mm thick 25mm deep termocol strip and filling the rest 25mm with Polysulphide Sealant (Poring Grade) as per drawings and technical specifications and direction of E/I. (with 18% GST) Brand - Sika-Polysulphide, Fosroc-Thioflex 600 Dr. Fixit Pidi Seal PS (42P), MYK Seal PS or Equivalent.

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars atevery third course of half brick masonry.

Providing and fixing Ist quality ceramic glazed wall tiles conforming toIS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black ofany size as approved by Engineer-in-Charge, in skirting, risers of stepsand dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,including pointing in white cement mixed with pigment of matching shadecomplete.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade - Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd class teak wood - 50 x 20 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile -B - Fixing with adjustable lugs with split end tail toeach jamb

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Steel work welded in built up srection / framed work, including cutting, hoisting fixing in position and applying priming coat of approved steel primer using structral steel etc . Aw required . In gratings frames , guard bar, ladder , rallings,brackets, gatestand similar works

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

kota stone slab flooring over 20mm (averagre) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab , including rubbing and polishing complete with base of cement mortar 1:4 (1 cement :4 coarse sand)

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300mm or more (thickness to be specified by the manufacturer), of 1stquality conforming to IS : 15622, of approved make, in colours White,Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4(1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matchingpigments etc., complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

Providing and fixing on wall face unplasticised-PVC moulded fittings / accessories for unplasticisedRigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conformingto IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler - 110 mm

Single tee with door - 75x750x75 mm

Single tee with door - 110x110x110 mm

Single tee without door - 75x75x75 mm

Single tee without door - 110x110x110 mm

Bend 87.5° - 75 mm bend

Bend 87.5° - 110 mm bend

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110mm

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2 mm thick corrugated (2.5" or 4.2" or 6") or step-down(2" or 3" or 6" ) as specified

Providing and Fixing 15 mm thick densified tegular edged eco friendlylight weight calcium silicate false ceiling tiles of approved texture ofsize 595 x 595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanised steel sections (galvanising@ 120 grams per sqm including both side) consisting of main ‘T’runner suitably spaced at joints to get required length and of size24x38 mm made from 0.33 mm thick (minimum) sheet, spaced1200 mm centre to centre, and cross “T” of size 24x28 mm madeout of 0.33 mm (Minimum) sheet, 1200 mm long spaced betweenmain’T’ at 600 mm centre to centre to form a grid of 1200x600 mmand secondary cross ‘T’ of length 600 mm and size 24 x28 mmmade of 0.33 mm thick (Minimum) sheet to be inter locked at middleof the 1200x 600 mm panel to from grid of size 600x600 mm, restingon periphery walls /partitions on a Perimeter wall angle pre-coatedsteel of size(24x24X3000 mm made of 0.40 mm thick

(minimum)sheet with the help of rawl plugs at 450 mm centre to centre with 25mm long dry wall screws @ 230 mm interval and laying 15 mmthick densified edges calicum silicate ceiling tiles of approved texturein the grid, including, cutting/ making opening for services likediffusers, grills, light fittings, fixtures, smoke detectors etc., whereverrequired. Main ‘T’ runners to be suspended from ceiling using G.I.slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mmdia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods withgalvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at1200 mm centre to centre along main ‘T’, bottom exposed with 24mm of all Tsections shall be pre-painted with polyster baked paint,for all heights, as per specifications, drawings and as directed byEngineer-in-Charge.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm overand including priming coat of exterior primer applied @ 2.20kg/ 10 sqm)

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineer- in-Charge. 80mm thick Cement concrete paver block of M-30 gradewith approved colour, design & pattern.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion - Powder coated aluminium (minimum thickness of powdercoating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) - Powder coated aluminium (minimum thickness of powdercoating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4.0 mm thickness

With float glass panes of 5.50 mm thickness

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mmthickness

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width

Providing and fixing 100mm brass locks (best make of approvedquality) for aluminium doors including necessary cutting and makinggood etc. complete.

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge. Powder coated minimum thickness 50 micron aluminiumtubular handle bar

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (The rate includes preparation of surface, treatment and sealing ofall joints, corners, junctions of pipes and masonry with polymer mixedslurry.)

Providing and injecting approved grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete/ masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in- Charge. Stirrer mixed SBR Polymer (of approved make) modifiedCement slurry made with Shrinkage CompensatingCement in concrete/RCC work.

Providing and fixing factory made single extruded WPC {Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58N/mm2 modulus of elasticity 900 N/mm

and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).

Note: For WPC solid door/window frames, minus Smm tolerance in dimensions i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Frame size 65 x 100 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In­ Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 35 mm thick

Compacting original ground- Compacting original ground supporting subgrade (Loosening of the ground upto a level of 500mm below the subgrade level, watered, graded and compacted in layers to meet requirement of table 300 2 for subgrade construction.)- Rolling with vobratory roller

Granular Sub-base with coarse graded material (Table:-400-2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401)- for grading - II material

Carriage of Material

Bricks - 8km (1k + 7p)

Sand - 30km

Chips -15km

Metal - 15km

Local Sand - 3 km

Paver Block - 8km

Fly ash Block -8 km

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

(c) From126.0 M to150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying Submersible pump sets confirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415V + 10%, 3PH, 50 Hz, A.C. supply with cable guard, thrust carbon/fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. the pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined non return valve shall be provided with pump. 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible Pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages - 2 HP

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work - 50 mm nominal outer dia Pipes

Supplying and stacking of good earth at site including royalty and cariage up to 5 km. (Earth measured in stacks will be reduced 8% for payment)

Supplying and stacking of sluge at site including royalty and cariage up to 1 km. (Earth measured in stacks will be reduced 8% for payment)

Supplying and stacking at site dump manure from local or other approved source including royalty and cariage up to 1 km. (Manure measured in stacks will be reduced 8% for payment). Screened through sieve of I.S. designation 4.75 mm.

Rough dressing the trenched ground including breaking clods.

Fine dressing the ground

Spreading of sludge, dump manureor / and good earth in required thivkness(Cost of sludge, dump manure or / and earth to be paid seperately).

Mixing earth and sludge or manure in proportion specified or directed.

Maintenance of Lawns or Turfing of Slopes (Maintenance of lawns or Turfing of slopes (rough grassing) for a period of one year including watering etc)

Providing and Displaying plants Marigold jaffri french orange/yellow/Russetcolour well developed with fresh & healthy foliage with 60 to 75 flowers inbloom specimen plant 60 to 75 cm ht in 30 cm Earthen Pot/Plastic Potand as per direction of the officer-in-charge.

Providing and Displaying plants Kochia well developed fresh & healthy 20to 25 cm ht. lush green well shaped in 20 cm Earthen Pot/Plastic Pot andas per direction of the officer-in-charge.

Providing and Displaying plants Sunflower single well developed 8 to 10half bloom buds multi branched in fresh & healthy full stacked with greenpainted bamboo stick stacking in 25 cm Earthen Pot/Plastic Pot and asper direction of the officer-in-charge.

Providing and Displaying plants Cosmos well developed fresh & healthy 20to 25 cm ht. attractive colours multi branching at blooming stage in 20 cmEarthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Portulaka hybrid in different colour withbloom well developed fresh & healthy in 20 cm Earthen Pot/Plastic Potand as per direction of the officer-in-charge.

Providing and Displaying plants Zinnia hybrid double in different colour welldeveloped fresh & healthy 30 to 45 cm ht. (3 to 4 plants in each pot) fullbloom in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Vinca different colour fresh & healthy 23 to30 cm ht. with bloom multi branchy in 20 cm Earthen Pot/Plastic Pot andas per direction of the officer-in-charge.

Providing and fixing Gun metal full way valve of approved quality all complete as per specification and direction of E/I.

32mm dia (wt-700 gram)

Cutting chajja or cornice for laying G.I. pipe and restoring the same with R.C.C. (1:2:4) brick work in cement mortar (1:4) and cement plaster (1:4) as per specification and direction of Engineer-in-charge.

Making holes in walls for laying G.I. pipes and restoring the same after pipe laying as per specification and direction of E/I.

125mm thick wall

250mm thick wall

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I.

Glass shelf with C.P. brass rail - 450mm x 125mm

Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror - 450mm x 300mm

C.P. brass towel rail 20mm x 600mm with bracket container

C.P. brass soap dish container medium quality with screw and hinges etc.

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I. 'p' trap 15 litres C.I. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware footrest to be fixed in floor 15mm C.I. body brass spindle stop cock of weight not less than 50grms, 15mm P.V.C. connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and dirction of E/I. 580mm long - With 10.0 liter low level PVC cistern

Supplying, fitting and fixing 40mm high viterous white glazed earthen E.W.C. with 'p' trap of Parry/hindustan or any other approved I.S.S. make including supplying and fixing 15 liters C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grams 15mm P.V.C. alkathene pipw 45cm. long with brass coupling at both ends and white/black plastic solid state seal and lead o commander/cuckoo or other I.S.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approvd paint over a coat of red oxide priming, all complete as per specification and direction of E/I. Witl, "P" trap - 10.0 liters low level P.V.C. cistern

Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthen ware urinal of Hindustan 'Parry' or any other approved I.S.S. make with 5 litres capacity C.i. automatic flusing cistern of reliance for any other I.S.S. approved make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grams, 15mm PVC/Alkthene pipe 450mm longwith brass coupling at both ends and doing plumber joints including priming coat of red oxide, cutting wall and floor making good the same etc. all complete as per specification and direction of E/I. Flat back or standard corner (600mm x 350mm)

Supplying fitting and fixing viterous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. approved make supported on painted C.I. or R.S. brackets 32mm C.I. brass waste, 15mm dia C.I. body brass spindl stop cock approved quality of weight not less than 30 grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.

Earth work in excavation for laying of different types and sizes of R.C.C. spun pipes with disposal of excavated earth within initial lead and lift as per specification and direction of E/I. For classification of soil item - A

Labour for alying, fitting and fixing NP2 R.C.C. spun pipe with colars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leakproof including providing sight rails, bonning rod, night guard, Red light and barrier etc. all complet as per specification and direction of E/I.

150mm dia RCC spun pipe - Upto 3.0 metre depth of invert below G.L.

225mm dia RCC spun pipe - Upto 3.0 metre depth of invert below G.L.

Supplying materials and labours for constructing inspection chamber of designation class 75B bricks size 750mm deep, 600 x 450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600 x 475mm G.I. Cover with frame (weight not leaa than 36 kg) alongwith earth work in exacavation and 80mm thick P.C.C. (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.

Supplying and fixing NP2 Hume pipe etc. (150mm dia)

Supplying and fixing NP2 Hume pipe etc. (250mm dia)

Special type C.P. Bath room Fitting for V.I.P.Buildings(JAL, Jaquar, Mark or Equivalent)

Piller Cock

bib cock long thread V.I.P

Angular Stop Cock/2 way bib cock

Centrel Hole Besin Mixure (Best Quality)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China Surgeon type wash basin of size 660x460 mm with single 15 mm C.P. brass pillar taps with elbow operated levers ISI marked

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto1 metre long with S.S. triangular plate to Eureopean type W.C. ofquality and make as approved by Engineer - in - charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Exposed on wall

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks ofclass designation 7.5

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge 100 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range5 cm to 20 cm, in recharge pit, in the required thickness, for allleads & lifts, all complete as per direction of Engineer-in-charge

Supplying, filling, spreading & leveling gravels of size range 5 mm to10 mm, in the recharge pit, over the existing layer of boulders, inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge

DT : Basic rates for 125/115mm dia drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of E/I.. (Basic Rates) Drilling upto 30 mtr. Depth below G.L. in Rural Area

Supply, Installation, Testing and Commissioning of electric driven, horizontally mounted type, single/multistage, end suction type, centrifugal pump of cast iron body, C.I impallers with carbon steel shaft & mechanical seal directely coupled with TEFC SQ cage foot mounted type induction motors suiitable for operation on 3 phase, 415 volts 50 Hz AC supply having flow rate as per fire safety guidelines complete in all respect as required or as directed by engineer incharge.

Main Fire Pump

Deisel Engine Pump

Jockey Pump

Terrace Booster Pump

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42.

For Pump Room

Providing and fixing IS marked Gate Valve / Foot Valve (incase of -ve suction) complete with companion flanges, bolts, nuts, rubber insetions etc.

150 mm diameter

100 mm diameter

Providing and fixing IS marked butterfly valve (PN 1.6) complete with companion flanges, bolts, nuts, rubber insetions etc.

80 mm diameter

100 mm diameter

150 mm diameter

Providing and fixing check valve (NRV) complete with companion flanges, bolts, nuts, rubber insetions etc.

80 mm diameter

100 mm diameter

150 mm diameter

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing, laying, testing & commissioning of IS 1239 marked black M.S pipe including all fittings i.e bend, elbows, tees, flanges, reducing socket, nuts and bolts, gaskets etc fixed with welded / screwed joints. including necessary excavation, backfilling, removal of surplus soil etc. min. 1 mtr deep excavation and wrapping with anticorrosive treatement with 4 mm thick asphalt tape as per IS:10221, refilling the trench etc. OR fixed with screwed or welded joints, hanged with clamps, hanger supports, dash fasteners, bolts, nuts, rubber insertions etc including threading, cutting, welding, edge preparation, painting of approved colour over two coat of primer, cutting & making good the wall/ floor wherever required, complete as required or as directed by engineer incharge. Make:Tata/Nezone/Jindal

150 mm diameter

100 mm diameter

80 mm diameter

25 mm diameter

Providing and fixing S.S Fire Hydrant Valve of approved quality with 63 mm female, instant, ovlique, single outlet, 80 mm flanged inlet, brass spindle, cast iron wheel m A.B.S. blank cap and chain. conforming to IS: 5290 complete with companion flange, bolts, nuts, rubber insertion / compressed asbestos gasket etc. and painted in fire red colour.

Providing and fixing swinging, wall mounting type First Aid Hose Reel of approved quality and made from compresed steel sheet with dust cover, cast iron brackets including 30 m long, 19 mm nominal bore, high presure braided rubber hose as per IS:444 Type hose guide, PVC shut off nozzle with 6 mm outlet and 25 mm nominal bore gun metal inlet valve, bolts, nuts rubber insetion etc. painted in Fire red colour including cutting and making good the walls wherver required.

Providing and fixing in position 63 mm nominal bore and 15 m long synthetic fibre, CP fire hose pipe of approved make bearing IS: 636 -1988 type A mark and having TAC and MMD approved with a pair of 63 x 63 mm gun metal instantaneous type, heavy duty delivery hose coupling (conforming to IS: 903) bound and riveted to the hose pipe with copper rivets and copper wire complete.

Providing and fixing in position short SS brach pipe of approved quality with 63 mm male instatneous type inlet and 15 mm outlet nozzle complete conforming to IS : 903

Supplying, fixing, testing & commissioning of 1 set of 63mm two way instantaneous fire brigade connection (FBC) with inbuilt NRV comprising of SS and four SS instantaneous male inlet coupling confirming to IS:604 with plug and cap with chain as required with nut & bolts, washers, high pressure gasket as required.

2 way-100 mm dia M.S. Pipe

4 way - 150 mm dia M.S. Pipe

Supplying, installation, testing and commissioning of optical type Smoke detector and mounting base with LED light complete as required. Make:ASES/Honeywell/Notofire/Bosch

Supplying, installation, testing & commissioning of response indicator on surface/recessed having two LED with cover complete with all connections etc as required

Supplying, installation, testing and commissioning of duel tone electronic hooter / Flasher / Strobe suitable for wall mounted complete as required. Make:ASES/Honeywell/Notofire/Bosch

Supplying, installation, testing and commissioning of manual call box in suitable enclosure with arrangement to raise the alarm when the glass is manually broken complete as required. Make:ASES/Honeywell/Notofire/Bosch

Supplying, installation, testing and commissioning of microprocess base main fire alarm control panel with LCD Display lights. The panels shall have 240 volts AC power supply automatic Battery charger 24 Volts sealed lead acid maintenance free battries as complete with batteries, battery charger illuminated numeric digram complete as required. Make:ASES/Honeywell/Notofire/Bosch Two Loop Panel.

Providing and laying 19mm dia PVC conduit complete with required junction boxes in recessed / surface system PVC insulated copper conductor cable of 2x1.5 sq.mm. with conduit as required. Make:Polycab/Mescab

Wiring for light point/fan point/exhaust fan/call bell point with 1.5 sqmm PVC insulated copper conductor cable in surface / recessed PVC conduit with moduler type switch,moduler plate,suitable size GI box etc. as required .

Wiring for light/ power plug plug with 2 X 4 sq. mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.(for AC &16A socket)

Wiring for light/ power plug plug with 4 X 4 sq. mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 2 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for submain wiring with the following size of PVC insulated, copper conductor single core cable in surface / recessed PVC conduit as required:

2x1.5 sq.mm.+1x 1.5 sq mm(for toilet switch board +6A socket)

2x2.5 sq.mm.+1x 2.5 sq mm(for switch board )

2 x6 sq mm +1x6 sq.mm. (Sub-MainsUPS DB's)

4 x 6 sq mm +2x6 sq.mm. (Sub-Mains Light DB's)

4 x 10 +2x6 sq.mm. (Sub-MainsPower DB's)

4 x 16 +2x6 sq.mm. (Sub-MainsPower DB's)

Supplying and drawing following sizes of PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit / PVC casing capping / as required. 2x1.5 sq mm

Supplying and drawing following pair 0.5 sq mm FR PVC insulated copper conductor unarmored telephone cable in the existing surface / recessed PVC conduit as required,

Suppyling and drawing co-axial TV cable RG-6 grade 0.7 mm solid copper conductor PE insulated shielded with fine tinned copper braid and protecred with PVC sheath in the existing surface / recessed steel / PVC conduit as reqd.

S/F of following sizes of PVC conduit alongwith the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required .

20 mm PVC coduit.

25 mm PVC coduit.

Supplying and fixing following moduler switch / socket on the existing moduler plate & switch box including connection but excluding moduler plate etc. as reqd.

5/6 amps switch

5/6 amps socket outlet

Telephone socket outlet

Supplying and fixing stepped type electronic fan regulator on the existing modular plate & switch box including connection but exluding modular plateetc.as required..

S/F Modular type blanking plate :- Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (78mmX78mmx45mm)

Supplying and fixing suitable size GI box with moduler plate cover in the front on surface or in recess including providing and fixing 3 pin 5/6 amps socket outlet and 5/6 amps. moduler type switch, connections painting etc. as required. (For light plugs).

Supplying and fixing suitable size GI box with moduler plate cover in the front on surface or in recess including providing and fixing 6 pin 15/16 amps socket outlet and 15/16 amps. moduler type switch, connections painting etc. as required. (For power plugs).

S/F 2 pin 5A ceiling rose on the existing junction box wooden block including connection etc ,as required.

Erection of wall bracket / ceiling fittings of all sizes and shapes ontaining upto two GLS lamp per fitting complete with all accessories including connection etc as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Installation of exhaust fan upto 450 mm. sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connections, testing, commissioning etc. as required.

Supplying and fixing following rating and breaking capacity MCCB with thermomagnetic release and thermal terminal spreaders in existing cubical panel / MCB DB board including drilling holes in cubical panel ,making connections ,etc.as required.

25/100 Amps 16KA fixed thermal setting

150/160 Amps 35KA fixed thermal setting

Supplying and fixing of following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts,on surface /recess, complete with tinned copper bushbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, including painting, earthing etc. as required.

4 way(4+12)double door Horizontal type

6 way (4+18)double door Horizontal type

8 way (4+24)double door Horizontal type

Supplying and fixing following ways, surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amp tinned copper bus bar, common neutral link, earth bar, din bar, for mounting MCB's (but without MCB's and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (8 + 24 ), Double door, Vertical type

Supplying and fixing 5 amps. to 32 amps. rating, 240 volts `C' catagory, miniature circuit breaker (10 KA) of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

single pole(6 to 32A)

6/32 amps.TPN

40 amps.TPN

63 amps. TPN

Supplying and fixing 20 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, TP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required.

Supplying and laying 25 mm X 5 mm GI strip at 0.50 metre below ground as strip earth electrode, including connection/ termination with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping with 2 sets of brass nut bolt and & spring washer spaced at 50 mm)

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

P/F of lighting conductor finial, made of 25mm. Dia. 300mm. Long GI tube, having single prong at top, with 85mm. Dia. 3mm. Thick copper base plate including holes etc. complete as required.

Rivetting, sweating and soldering of copper/GI tape (with another copper/GI tape base of the finial or any other metallic object) as required.

Providing and fixing GI tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as reqd.(for horizontal run)

Providing and fixing GI tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as reqd.(for vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of tinned G.I. bolts, nuts, chuk nuts and spring washers etc. complete as required.

Laying of PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size exceeding185 sq mm but not exceeding 400 sq mm Direct in ground including excavation ,sand cushioning protective covering and refilling the trench etc as required.

Laying of one number additonal PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade. of size not exceeding 185 sq mm but not exceeding 400 sq mm Direct in ground in the same trench in one tier horozontztal formating including excavation ,sand cushioning protective covering and refilling the trench etc as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade.of following size on wall surface as required. upto 35sq.mm.(clamped with 1 mm thick saddle)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade.of following size on wall surface as required. Above 35 sq mm and upto 95 sq mm (clamped with 20mmx3mmGI tape)

S.I.T.C of following rating LEDstreet light luminaiere with pressure die cast housing and toughend glass cover (IP 66 protection )in xisting pole/pipe for supply voltage 100-270 AC 50 Hz luminarie shall be confirm to IS:10322 part-5/section 3and shall be complete with all necessary accessories as required. 120W LED street light.

S.I.T.C of following rating recess/ surfface mounted LED round /square shape down light luminaierewith pressure die cast housing for single phase supply voltage luminarie shall be confirm to IS:10322 part-5/section 2 or IEC :62722 with all necessary accessories as required.

12w LED round down light.

18/20w LED round down light.

2' x 2' LED panel light.

6 w COB based round LED light with multiple beam angles (36 Degree)

S.I.T.C of following size ceiling fan 3 blades confirming to IS-374:2019including wiring the down rods of standared length (upto 30 cm)with 1.5 sq mm FR PVC insulated copper wire suitable for 230v 50Hz single phase supply etc.as required. 1200mm (48")BL DC 5 star rating 32w Ceiling fan

S.I.T.C of following rating surfface mounted LED tube light fitting suitabe for 230v 50Hz single phase supply etc complete as required

10/12w LED tube light

20/22w LED tube light

S.I.T.C of following rating LED post top lamp made in die cast aluminium housing with decotative clear / opal acrylic diffuser on existing pipe including connection with 1.5 sq mm copper conductor etc all complete as required. 20/25w LED post top lamp opel

Supply of PVC/ XLPE Insulated PVC sheathed heavy duty armoured electric cable with alluminium conductor for working voltage upto and including 1100 volts (conforms to IS:1554,part-1)

10 sq mm x 2 core

10 sq mm x 4 core

50 sq mm x 3.5 core

70 sq mm x 3.5 core

300 sq mm x 3.5 core

Supplying of 7 Mtr height octagonal Hot-Dip Galvanized pole (BOP-7030) with top dia 70 mm,bottom dia 130 mm & made of 3 mm thick sheet ,base plate diamentions 200 MM X 200 MM X 12 MM (LxBxT) including suitable size of foundetion bolt and 1'6'' long 50mmX50mm MS angle along with welded horizontally on top of octagonal pole all complite on exiting concreat platform as required

Supplying and fixing of 1.5 mtr single arm suitable for 70 mm top

9" (230) mm )metal exaust fan

400mm Wall Mounted fan

Providing of bulkhead fitting with 9/10w LED bulb.

S/F of Earthing electrode 80mm dia x 3mtr with backfill compound chemical 4 bag (per bag 25Kg)including earth cutting removing and installation charge.

Installation,testing and commissioning of the 7mtr octagonal pole and light fitting with the help of suitable tools and plants ,wiring of luminaires with all materials and construction of shallow foundation with M25 grade concrete considering safe soil bearing capacity of 10T/mtr sq.

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

1.53 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

1 run of cable

2 run of cable

3 run of cable

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3½ X 50 sq. mm (35mm)

3½ X 70 sq. mm (38mm)

3½ X 300 sq. mm (70mm)

MAIN DISTRIBUTION BOARDS / L.T. PANEL.

LT PANEL (NORMAL SUPPLY) : -INCOMING (1- sets) each with following: 400 Amp, MCCB FP -2no, Ammeter, ASS, CTs, Voltmeter, VSS, Fuses, 1 Sets of Phase Indicating Lights with fuses & following accessories: - BUS BARS : 500 Amp, 415V, 3 phase, 50 Hz TPN bus bars. OUTGOING ; 100 Amp, MCCB FP -4 no, 160 Amp, MCCB FP -4 no, 6/32 Amp, MCB TPN -5 no, 40 amps. MCB TPN -4 no, 63 Amp, MCB TPN -4 no, 6/32 Amp, MCB SPN -4 no, LT Panel (Normal) as above ( G.F)

Supplying outdoor type copper wound transformer continuosly rated for 3ph 50Hz at full load and temp.rise not exceeding 450 c by thermometer in oil and 500c by the resistance in winding after continuous run at full load rating ,the transformer should have oil unmersed winding having vactor group DY11 HT side connected in delta and LT sideconnected in star with neutral brought out connected to provide separate earthing .The transformer shall have power terminal arrangenent bushing / cable end box on HT side and cable end box on LT side 2 nos channels with stoppers shall be provided and fix on the provided plinth for mounting the transformer .The transformer should have following standard fitting.Transformer shall be latest manufacturing standards as per amended IS specification and the load & No load losses shall be limited to the values given below or as per IS 2026 or norms issued by SEB which ever are lower.

Oil conservator with filling hole with cap and plain oil level gauge.

Silica gel dehydrating breather charged with silica gel

oil drain valve

Lifting eyes / hooks

Two earthing terminals

Digram and rating plate

Air vent

Explosion vent

100 mm dia thermo meter with thermometer pocket

Four bi directional plain rollar

Power transformer 11000/433V with off load tap changer -12.5% to +2.5% in steps of 2.5% per BIS leveel-2

250KVA (No load loss 500w and load loss 3000w)

Supply fully automatic star delta starter to oprate induction motor working on 415 V , 3 phase, 50 HZ with no volte coil over load element ON-OFF push buttons with necessuy materials and connected to supply etc. complete starter with oroginal sheet steel encloser as per IS : 3914

Non Schedule Items

For Terrace Pump

Pressure Gauge Assemble with Gate/Ball Valve

Air release Valve / Drain Valve

MS Structure support for piping

Providing and fixing 25 mm nominal gun metal gate valve class I with CI wheel of approved quality with union (Screwed end)

Providing , fixing Dry Chemical Powder (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 20oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (4 Kg Capacity)

Carbon Di-oxide Type , Gas Confirming to IS ‘15222’ , Cylinder Confirming to ‘IS 7285’ & PESO approved ,Controllable Discharge Mechanism, Discharge Hose & Horn As per ‘IS 15683’ & ‘IS 2878’ ISI mark Fire Extinguishers (Wheel Type or Squeeze Grip Type). Operating Temperature :- (-)20oC to (+)55oC Suitable for ‘B’ ‘C’ Class of FIRE (4.5 Kg Capacity)

Providing , fixing Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (5 Kg Capacity)

Supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect.

Add 12% GST

Add 1% Labour Cess

HEIGHTEN CONSTRUCTIONS