ADDN/ALTN TO MAIN GATE OF STN KSP, SPL REAPAIRS TO ROOF, TOILET SUNKEN TREATMENT AND EXTERNAL FACIA OF STN JCOS MESS AND PROVN OF TILING FLOORING, FALSE CEILING AND CONNECTED B/R WORKS AT HQ MAO AFI UNDER GE (W) COLABA, MUMBAI

Amount

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified including scafoldings of any height all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed.

S&F joist, channel, angle, tee sections and MS flats fixed independently, with/without connecting plate, etc. (cut to ordinary lenghts i.e. within 20mm of the length indicated) use for single stanchions, purlins, rafter including plate, nut bolt and necessary fixing arrangement fixed to wooden rafters and all other similar works conforming to Fe 410-W (Gde-E-250) all as specified and directed

Demolition of cement concrete in ground floor & paving nexc 15 cm thick (below or above GL) unreinforced all as specified and directed.

M&L PCC 1:4:8, type D2 (using 40 mm graded crushed stone aggregate) as in foundation filling, mass concrete and sunken floor treatments all as specified and directed.

M&L Water proffing treatment to sunken slab /walls and shall be carried out as specified below and as directed. (a) Clean the sunken partion of Toilet/baths/WC/Kitchen throughly to remove the laitance, dirt etc (b) Form angle fillet of size 40 mm X 40 mm along the junction of wall above floor using polymer modified mortar. (c ) Sanitary pipe entering through walls and floor shall be sealed with bath seal tape and gaps to be grouted with non shrink cementious grout bath seal grout or eqvt. Nahani traps etc to be fitted securely and gaps around it to be grounted in the manner. (d) Apply one coat of Bitumen modified polymer coating bath seal plus on all angle fillets by brush and cover it with 100 mm open woven mesh when it is still wet. Apply second coat of the same coating on the angle coating fillet and allow it to dry. (e) In the remaining area in dry substrate condition brush apply first coat of the same coating and further apply second coat when first coat is dry. Extend the coating up to 150 mm above the FFL another cementitious water proof coating and further applied right up to water 2.1 m to water proof the shower also, if it is a bathroom or bath cubical of a sanitary annex and apply second coat after 6-8 hours and allow to dry completely. (f) After 2 to 3 days sunken portion must be overlaid with a 50 mm thick concrete screed 1:3:6 type B0 mixed with integral WPC liquid laid to slope 1:60 towards outer face of wall. Provide 40 mm OD UPVC pipe at the lowest point with 300 mm projection beyond the outer face of the wall, then filled up the sunken portion with lean concrete 1:5:10 type E2. (g) After completing plumbing work in the toilet, WC, bath, Kitchen floor tiling work (floor and dado) can be carried out using suitable tile adhesive and ready to make tile grouts of approved makes. Note : all the material involved in sunken treatment are included in above quoted rate.

M&L rendering 10mm thick on fair faces of brick work or concrete surfaces in Cm 1:4 all as specified and directed.

Demolition of brick work built in CM including all quoins arches pillars etc and precast articles includings disposal of demolished material all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6 mtr mean raddius built in CM 1:6 all as specified and directed.

Dismantling of floor, hearth/wall tiles including cement mortar bedding (but not backing) and removing serviceable tiles away from the sites all as specified and directed..

M&L Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exc 0.36 sqm but not exc 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match Coloured in floor including 15mm thick screed bed or bedding layer in CM1:6 all as specified and directed.

M&L for Coloured vitrified tiles 10 mm thick, area of each tiles not exc 0.42 sqm as in skirting and dados etc including 10 mm thick rendering coat in CM(1:4) set and jointed in neat cement slurry and pointed in coloured cement to match all as specified and directed.

M&L for vitrified ceramic tiles 7-8 mm thick, area of each tiles exc 0.18 sqm but not exc 0.38 sqm as in floors including 15mm thick screed bed or bedding layer in CM(1:6) set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with 6 mm spacer filled with epoxy grout all as specified and directed.

M&L for vitrified ceramic tiles 7-8 mm thick, area of each tiles exc 0.18 sqm but not exc 0.38 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade including 10mm thick rendering coat in CM 1:4 all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8 mm thick, area of each tiles exc 0.11 sqm but not exc 0.18 sqm as in floors including 15mm thick screed bed or bedding layer in CM(1:6) set and jointed in neat cement slurry and pointed in coloured cement to match all as specified and directed.

M&L Glazed ceramic tiles in vertical surface size 600X 300X 7 / 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade including 10mm thick rendering coat in CM 1:4 all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons all as specified and directed.

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and rounding to edges of slab including screed bedding 15mm thick in CM (1:6) all as specified and directed.

M&L Machine cut kota stone slab flooring 20-25mm thick over cement rendering in riser of steps, skirting, dado and pillar and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and rounding to edges of slab as in including screed bedding 10mm thick in CM (1:4) all as specified and directed.

M&L Granite (of any type and size) 20mm thick machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone over 15mm thick screed bed in CM 1:4 on kitchen platform, Cill of Window/Ventilator/ flooring/border etc including rubbing, grinding and polishing all as specified and directed

M&L 20-25 mm thichk machine cut cudappa stone slab in horizental/vertical jambs laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing polishing & rounding to edges of slab as in window cills/jambs including screed bedding 10mm thick in CM 1:6 all as specified and directed by Engineer-in-charge..

Taking down cement plaster on brick /stone walls/ ceiling etc including racking out of joints, hacking for key, scrubbing down with water to receive plaster, including complete and disposal of rubbish out of the MD land. Note Height of the bldgs five & above upto eight stories, including use of scaffolding complete all as specified and directed.

M&L for applying average 20 mm thick plaster in two coats with ready mix prepacked proportioned dry mix mortar, blended with PP fibers, mixed with liquid water proofing compound on other than fair faces/fair faces of brick wall or concrete surfaces additives, on external surfaces including transporting of material, mixing, curing, scaffolding all as specified and directed. Note :- Liquid water proofing compound will be measured and paid seperately as supply only

Supply only integral water proofing compound.

M&L for Providing and applying average 12-15 mm thick plaster in two coats in CM 1:4 with ready mix prepacked proportioned dry mix mortar, blended with PP fibers, on internal surfaces including transporting of material, mixing, curing, scaffolding all as specified and directed.

M&L for preparing old/new plastered surfaces of walls /ceiling and applying two coats of oil bound distemper over a coat of alkali resistant primer including scaffolding all as specified and directed.

M&L for preparing new surfaces of walls applying two coats of weather proof acrylic exterior paint (100% Acrylic) Base coat and top coat over a coat of alkali resistent primer through authorized applicator only including use of scaffoldings all as specified and directed.

M&L for Providing & applying anti algal water-based Elastomeric exterior wall finish on old/ newly plastered surface including surface preparation, applying suitable wall Primer and application of two coats of paint by brush etc Including scaffoling and all necessary arrangements all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frames) area exc 1.5 sqm but nexc 4 sqm integral all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frames ) area nexc 1.5 sqm each all as specified and directed.

M&L for second class hardwood (sal) plain, solid, straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and directed.

S&F 35 mm thick flush shutter, solid core construction, with block board core and plywood face panel, commercial type covered with decorative face veneers on both sides with lipping all as specified and directed.

S&F Powder coated ( any shade approved by GE ) aluminium frame/shutter for door, window, ventilator, partions of any type including sliding/hunge type all as directed with one or more rebates including fabrication of frame/shutters and fixing to wall with necessary lugs, cleat etc including all accessories such as glazing clips and rubber beading for fixing of glass panes, hinges, locks all as specified and directed . Notes:- (i) Glass panes/Wire cloth will be measured and paid seperately. (ii) The quoted rate rate shall be inclisive of cost of rubber beading, glazing clips and locking arrangement. (iii) Joint shall be completed using silicon gun is included in quoted rate.

S&F sheet glass 4 mm thick ordinary quality in square n.exc 0.5 sqm in each pane and fixed with rubber beads all as specified and directed.

M&L for 3mm thick sheet glass Figured glass, pin head type and glazing with oil putty in square n-exc 0.5 sqm in each pane all as specified & directed.

S&F aluminium grill 7.5mm x 5.2mm bars of opening as per design No DG No 103 of M/s Decogrill/ RG-103 of M/s Royal Grill fixed with aluminium channel 'F ' 20mmx15mm fixed in position with screw all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing on Serial Page No 160 of SSR Part II (pertaining to item No 08095) and edges to be painted to match with prelam sheet all as specified and as directed by Engr-in-Charge.

S&F Factory made solid panel PVC door shutter 30mm thick (style consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert fort top rail & bottom. Panelling of plain colour PVC sheet to be fited in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

S&F door closer, aluminium body (extruded section) hydraulically regulated designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg all as specified and directed.

S&F in repairs Door closer, aluminium body (extruded section) hydraulically regulated designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg all as specified and directed.

S&F aluminium anodised barrel tower bolt 200 mm long of extruded section all as specified and directed.

S&F aluminium alloy anodized sliding door bolt 300mm long with hasp and staple fixing clips all as specified and directed.

S&F Anodised aluminium alloy handles cast type, each 150mm long all as specified and directed.

S&F Mild steel butt hinges medium weight cold rolled 100 mm long all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolt of extruded section all as specified and directed

S&F 100mm long Aluminium butt hinges of extruded aluminium alloy with galvanized mild steel hinge, pin anodized all as specified and directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10cm in widht or girth and applying two coat of synthetic enamel paint all as specified and directed.

M&L for preparation of old painted steel surfaces of any description not otherwise described over 10cm in widht or girth and applying one coat of synthetic enamel paint all as specified and directed.

M&L preparing old wooden surfaces of any description not otherwise described over 10cm in width or girth and applying one coat of synthetic enamel painting all as specified and directed.

M&L preparing new wooden surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel painting over a coat of pink primer all as specified and directed.

S&F in repairs Aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperature 1.40mm and fixed with aluminium wire staples all as specified and directed.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement all as specified and directed.

S&F in repairs Vitreous China valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including bracket complete with including cast iron bracket and 32mm bore PVC flush pipe and connection to WC all as specified and directed.

S&F in repairs white Vitreous china semi wash down water closet pan (pedestal pattern Anglo India) of 1st quality including plastic water closet seat, white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device including flush pipe and fixing bolts (excluding flushing cistern) all as specified and directed.

S&F in repairs vitreous china wash basin white flat back, size 550 x 450mm (of 1st quality) including CI brackets, 32mm waste pipe, CP waste coupling, CP pillar tap etc all as specified and directed by the Engineer-in-Charge all as specified and directed.

S&F in repairs PVC connection 15mm size with PTMT nuts of length 450 mm all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail 20 mm dia, D type 60 cm long, between flanges fixed as specified and approved.

S&F in repairs PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall/floor in repair all as specified and directed.

S&F in repairs PVC (SWR) 75mm bore pipes single socketed in any length with rubber ring joints fixed to wall/floor all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radius all as specified and directed.

S&F in repairs PVC nahani trap with grating 75mm dia outlet jointed to waste pipe fixed in cement concrete type (1:2:4) in repairs all as specified and directed.

Taking up or down steel tubing and connections 15 mm bore, including cleaning for refixing or removal all as specified and directed

S&F GI tubing medium grade 15mm bore laid to walls and ceiling or laid in floors all as specified and directed

S&F in repairs stop cock (Consealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union of size 15mm all as specified and directed

S&F in toilet coloured paper holder, vitreous China, box typer all as specified and directed.

S&F Grating round 140 mm size of PTMT. (Minimum weight 50gms) all as specified and directed.

S&F in repairs angle cock chromium plated 15 mm bore dia all as specified and directed.

S&F 15 mm Pillar taps, fancy type with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed all as specified and directed

S&F 15 mm dia bib taps cast copper alloy with Chromium plated cruch or butterfly handle scrwed, screwed for iron pipe or for brass ferrule and fixed all as specified and directed

S&F Shower arm 15 mm size, 195mm long with bend of 45 degree with flange of PTMT any colour (Minimum weight 40gm all as specified and directed.

S&F Gypsum Board 12mm thick of size 600X600 in ceiling fixed with screws as per manufacturers instructions all as specified and directed.

M&L Aluminium Anodised snap grid frame work for false ceiling of size 605 x 605 mm including GI suspenders, expansion hold fasteners all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided all as specified and directed.

M&L PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) finishied surfaces even and rough to receive the tiles all as specified and directed.

M&L PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in coping all as specified & directed.

M&L POP ceiling including cornice of POP fixed on anodised snap grid frame work for false ceiling with size of grid 605x605mm consisting of main and cross tee of size 36.5 x 25 x 1.4 mm (wt 0.24 kg/RM) and 23.5 x 26.4 x1.4mm (wt 0.191 kg/ RM) respectively including aluminum angle 25x25 1n4 mm & provn of hangers of GI wire of 2mm dia and providing painting with two coasts of synthetic enamel paint over a coat of primer on wooden surfaces all as specified and directed by Engineer-in-Charge.

M&L E-board tiles ceiling on GI powder coated channel/Tee/Grid of frame work with the following specification including cutting holes in brick wall built in cement mortar & making good in cement concrete 1:2:4 type BO/Cement mortar 1:3 all as specified and directed with following:- (a) M&L Plugging to wall around the rooms & supplying & fixing GI powder coated angle of size 25 x 25 mm. (b) S&F 0.90 mm dia GI wire suspenders with adjustable clamps including fixing to ceiling with dash free fasteners. (c) S&F GI powder coated Tee as in main & cross members at 595 mm centre to centre supported suspenders along with adjustable camp to maintain level. (d) S&F E-board ceiling tiles of size 595 mm x 595 mm x 4 mm thickness, confirming to relevant IS in squares of GI powder coated Tee with clips made to shape, shade and pattern of tiles shall be as approved by GE

M&L lnsulated PVC Wall Lining 25 mm thick consisting of PVC Insulated panels having expanded polystyrene (EPS) stuck to 2mm thick wood grain printed PVC sheet duly fitted into the wall as per specifications and drawing all as specified and directed.

M&L 5mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site all as specified and directed.

Demolition of reinforced Concrete of any description and in any position not otherwise described all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for all as specified and directed.

Use & waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for flat surface and fair finish all as specified and directed.

Use & waste form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc for flat surface and fair finish all as specified and directed.

Use & waste formwork to sides of pillars, posts, struts, piers, columns and stanchions for Square rectangular or polygonal surface and fair finish all as specified and directed.

M&L RCC works as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc. in M-30 (Design Mix) using 20 mm nominal size graded crushed stone aggregate all as specified and directed.

M&L RCC works as in Columns, pillars, piers, posts and struts etc. in M-30 (Design Mix) using 20 mm nominal size graded crushed stone aggregate all as specified and as directed by Engr-in-Charge

M&L RCC works as in Beams, cantilevers, bressummers, lintels over 1.5m span etc. in M-30 (Design Mix) using 20 mm nominal size graded crushed stone aggregate all as specified and as directed by Engr-in-Charge

M&L mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and Old unserviceable of any height all as specified and as directed by Engr-in-Charge.

M&L mild steel TMT bars 8 to 10 dia as in stirrups, spaces and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips all as specified and as directed by Engr-in-Charge.

M&L PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in benching/cooping and sub base set in CM 1:6 all as specified and directed.

S&F framed work such as grills, gratings etc with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, windows, balcony in ground floor, framed balusters, walk ways, railings, framework of water tanks and similar work for ornamental and intricate design in conforming to FE 290 Gde -E-165 all as specified and directed.

Excavation in trenches nexc 1.50 m wide and nxc 1.50 m in depth for foundation, drain pipes, sewage lines etc and getting out in soft loose soil all as specified and directed.

M&L sub base 100 mm thick cement concrete type D2, 1: 4 : 8 ( using 40 mm graded crushed stone aggregate) all as specified and directed.

M&L machine pressed precast concrete interlocking paver block glossy finish any shape and size confirming to IS 15658 - 2006 of 80 mm thickness, M- 40 grade with grey cement and no pigment including 40 mm thick sand cushioning layer all as directed and specified

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm all as specified and directed.

Removing excavated (soil) materials and deposited out of MD land up to a distance of 15 km all as specified and directed.

S&F in repairs PVC tensile fabric structure with PVDF ( polyvinyl-idene-fluoride) Coating with all necessary fixtures, of any size and shape for making capopies, shade etc fixed with mild steel structural frame work, weight of the fabric is considered, with fabrics ranging from 900 GSM all as specified and directed. Note :- (i) The shape / Design of the shade will be as approved By GE.

S&F in repairs stainless steel letter 450 mm height and 32 mm depth made of 1 mm thick Stainless steel sheet with seamless welding rubbed, polished and edges made smooth with necessary fixing devices all as specified and directed.

S&F in repairs Aluminium composite panel sheet 3mm thick PVCF wooden or plain finished fixed with necessary aluminium tube of size 25mm x 38mm x 1.5mm thick with required silicon & screw as in ceiling/coloumns and in vertical surface all as specified and directed. Approved sample as kept in GE Office.

M&L in repairs for Best quality granite (of any type) 18 to 20 mm thick machine cut, beded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing all as specified and directed.

Molding (Sandwitch moulding) of granite slab edges including polishing all as specified and directed.

M&L for first and premium quality of vetrified coloured marble finished digital tiles 1200 mm x 600 mm x 8 to 10 mm thick, in skirting, dados, risers to steps, etc set and jointed in neat cement slurry and pointed in coloured cement to match the shades of the tiles laid over and including 10mm thick rendering or backing layer in cement mortar 1:4 all as specified and directed.

M&L for heavy duty outdoor vitrified tiles dark or light shade 10-12 mm thick (square/ rectangular) polished, area of each tiles exc 0.16 sqm and not exc 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles laid over and including 20 mm thick screed bed or bedding layer in cement mortar 1:6 all as specified and directed.

Taking down carefully copper/aluminum point wiring light/fan/sockets out let/power point complete (fittings such as switches, sockets, ceiling rose, pendent holders, light fittings etc. are to be measured separately) and/or drawing out from existing conduit/batten and making good disturbed surface of walls/floors/ceiling all as specified and directed.

M&L for Point wiring with 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, concealed with accessories and incuding provision of 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including cover plate & mild steel sunken box/metal flush box with suitable modular or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches, socket outlets, fan regulators with brass screws and brass washers and making good the disturbed surfaces as per existing for one light point controlled by one switch. Note :- Switch, socket and fan regulators to be measured and paid for separately.

All as per Srl item No.107 here in before but for socket outlet point 5 Amp on same board.

All as per Srl item No.107 here in before but for socket outlet point 5 Amp on Independent board.

All as per srl item No 107 here in before but with 4 sqmm cable for 3 pin 15 Amps switch socket outlet (Power point) all as specified and directed. Note: Earthing wire should also be of 4 Sqmm.

S&F switch piano (ISI marked) Single pole 240 volts, 5 Amps all as specified and directed.

S&F socket (ISI marked) 2/3 pin and 5 Amps, flush type, 240 volts all as specified and as directed.

S&F switch socket combination (ISI marked) 2/3 pin and 5/15 Amps, flush type, 240 volts all as specified and directed.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet all as specified and directed.

S&F ceiling rose surface bakelite 65x50mm, 3 terminal all as specified and directed.

M&L for refixing of ceiling fan (old fan) and servicing complete connecting up including provision of cable from ceiling rose to connector and fan Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. with taking down fan, sealing cable end, dismantling romoving and hanging fan and blades and making fuctionae i .e change capacitor, condenser, fan rod 3 to 5 RM of GI pipe, winding, servicing all as specified and directed.

S&F in repairs 20 watt LED, 6500 K, 4 feet long fixed including on PVC square for mounting the fittings and electrically connecting with three single core 23/0.0076. PVC insulated multi strandard copper flexible cable from ceiling rose to light fitting (connector block of lamp fitting) and one for earthing all as specified and directed

S&F 1x 10W, 220, LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V, AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete, AC decorative box type, bright white / white type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete pre wired fixed to wall with 2 nos PVC block of suitable size all spcifided and directed.

S&F LED Wall bracket decorative fancy light fitting warm white /white type with lamp 12 Watt with necessary connection all as specified and directed.

S&F LED down lighter 15 watt warm white fancy light fitting warm white /white type with lamp 12 Watt with necessary connection all as specified and directed.

S&F in repairs ceiling fans complete with blades, down rods of required size, electronic regulator and accessories, 230 V, 1400 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with scquirel cage induction motor, including taking down old fan and depositing safely to MES store Note: Connection should be made neatly using two core flexible cable.

S&F Exhaust fan 230 volt, 225 mm sweep, heavy duty metal body with wooden frame including making all electric connection including cutting of hole on wall and makng good to disturbed surface of wall and outer wooden box for fan fix on wall all as specified and directed.

S&F Electrical kitchen chimneys 90cm with suction capacity 1250 Cum/hour, copper winding motor, LED lights with all necessary connections including proper necessary ducting and attaching mesh at outlet all as specified and directed.

S&F Moduler stepped type electronic fan regulator 120 watt flush type, two module all as specified and directed.

S&F LED security Building light LED 45 Watt, pressure die cast aluminum housing, heat resistant glass, IP65/66 protection, better optics for uniform distribtion complete with all accessories internally pre wired and including connecting up with three core 1.5 sqmm flexible copper conductor cable from ceiling rose to connector of light all as specified and directed.

S&F in repairs MCCB DB 4 way vertical sheet metal enclosure TPN 415 volts, 50 Hz, with IP-43 protection, double door with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting all as specified and directed. Note : MCB SP/TPN shall be measured and paid seperately under appropriate items of this schedule. Note : Copper thimble shall be used for connection of cable.

S&F in repairs MCCB TPN, 415 Volts, 63 to 100 Amps, 16 kA rupturing capacity 415 Volts all as specified and directed.

S&F in repairs MCB, single pole 240 volts 6 to 32 Amps capacity fixed in DB's all as specified and directed.

M&Lin repairs Sub main wiring with two run of 6 sq mm stranded copper conductor PVC unsheathed FRLSH wire along with 6 sq mm green colour wire as earth contuinity conductor connected to common earth dolly concealed including PVC FR heavy duty conduit of adequate size (not less than 25 mm dia) for housing the wires from Pannel / Main DB to house SPN DB including taking down old Unsv submain with all associated fixtures all as specified & as directed by engr-in-charge Note: Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. Note: Mode of measurement two runs of 6 sqmm cable and one run of 6 sqmm cable with PVC conduit shall be measured as one length.

M&L in repairs Sub main wiring with two run single core 4 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 V including 20 mm dia Cassing capping ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall along with one run of 4 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continueous earth wire and connecting to existing main switch board / distribution board and testing on completion inculding taking down old wiring all as specified and directed. Note: (i) Two runs of 6 sqmm and one run of 6 sqmm cable and one run of PVC conduit shall be measured as one RM length.

M&L Sub main wiring with two run single core 1.5 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 V including 20 mm dia Casssing capping ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall alongwith one run of 1.5 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion inculding taking down old wiring all as specified and directed. Note: (i) Two runs of 1.5 sqmm and one run of 1.5 sqmm cable and one run of PVC conduit shall be measured as one RM.

M&L for earthing complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth not less than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers, galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cmX 5 cm with 10mm dia TMT bars 8 cm C/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including necessary testing on completion all as shown in Electrical Plate No 3 of SSR part -I.

Unitech Enterprises (BID ID -3223181)

SAHI SAGAR ENTERPRISES (BID ID -3223859)

Panther Facilities (BID ID -3223203)

Bright Construction Co (BID ID -3222574)

N F ENTERPRISES (BID ID -3223788)

SAHU AND SAHU CO. (BID ID -3222628)

SR Construction (BID ID -3223538)

Nilesh Construction (BID ID -3223741)

Bidder Name

Unitech Enterprises

Nilesh Construction

SAHU AND SAHU CO.

Panther Facilities

Bright Construction Co

SR Construction

Shivam Enterprises

SAHI SAGAR ENTERPRISES

N F ENTERPRISES