PROVISION OF CEILING FAN FITTING WITH ALL ACCESSORIES AGAINST BER, REPAIR FOR REPLACEMENT OF UNDERGROUND THREE PHASE CABLE FROM GENERATOR ROOM TO ADMIN BLOCK AND REPLACEMENT OF MP TILES WITH GALVALUME SHEETS IN BLDG NO 6 MH OPD COMPLEX 8 MH CHANDAN G

Amount

Supply and fix in repairs Ceiling fan complete with 03 Nos of blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed. Make :Bajaj /Orient/CG . NOTE : (i)SM No shall be written and painted in each fan provided at site . (ii) Documentary evidence for Sl no : 01 above and PRB register shall be produced to GEs office before claming Payment by the contractor.

Dismantling of single layer Mangalore pattern or similar tiles in roofing and taken as credit complete all as specified and as directed.

Dismantling battens in roof tiles of any size spaced exceeeding 15 cm including tiling fillets and taken as credit complete all as specified and as directed.

M&L for 2nd class hard wood in scantling, clean sawn fixed in framed work including dismantling timber scantling 40sqmm over in section in any position of framed work all as specified and directed.

Supply and fix Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws and washers complete all as specified and directed. Note :Make : TATA BLUE SCOPE/LLOYD INSULATIONS LTD/METCO

Supply and fix Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and washers complete all as specified and as directed. Note : Make : TATA BLUE SCOPE/LLOYD/METCO

Material and labour for Providing Cement concrete Type B0 1:2:4 (12.5 mm graded stone aggregate) in roof kerbs or mud stops ,coving or chamfered on edges including necessary steel form work complete all as specified and as directed.

Supply and fix in repair Rolled mild steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes confirming to Is 1161-1979 grade St-240 complete all as specified and as directed.

Supply and fix Mild steel flats for wind ties for roof including securing bolts and similar work confirming to Fe-290 Gde E-165 complete all as specified and as directed.

Supply and fix Mild steel Bands ,straps ,supports or stays for rain water ,ventilating pipes including bolts if required ,hooks (stay) ,heavy for large gates , hook and pintel hinges ,large hasps and staples ,chains ,hand made sliding bolts ,clamps ,hold fasts ,wall ties , hooks for hanging fans ,plain angle cleats for securing purlins to wood trusses or rafters ,knee piece inserts ,two way and three way straps ,plate washers and similar small articles confirming to Fe-290 Gde E-165 complete all as specified and as directed.

Material and labour for Preparation of new steel surfaces over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for laying of LT UG cable/pipe in hard/dense soil complete all as specified and as directed.

Returning, filling in excavated soil including spreading, levelling, watering and well ramming in layers n.exc 25cm thick complete all as specified and as directed.

Removing surplus soil n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed.

Supply and lay Double Wall Corrugated High density polymer Ethyl pipe PN8 (SDR 17 ) of size 110mm outer dia with ISI Mark confirming to IS 14930-2001 laid in trenches /floors and fixed on wall/pole with and including necessary fittings like couplers, bends, end caps etc. for LT/ HT cable protection complete all as specified and as directed . Note : (i) Make of DWC Pipe : Duraline/REX/KETRON (ii) Earth work excavation shall be measured and paid under relevent items .

Supply and lay XLPE insulated screened PVC bedded , galvanized steel strip or wire armoured electric power cables (heavy duty ) 1100 volts graded with standard aluminium conductor of following sizes including taking down unserviceable LT UG cable of any description and size and taken as credit complete all as specified and as directed.Note :Make of cable : CCI/Gloster/Finolex

185sq mm 3.5 core size

95 sq mm 3.5 core size

50 sqmm 3.5 core size

Material and labour for Boring of holes under road pavement hard standing using ultra sound technique and necessary machine including Provision of HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressurecomplete all as specified and as directed. Note : (i) Make of HDPE Pipe : Finolex/Supreme.

Material and labour for Earthing complete with galvanised steel earth plate electrode 60cmx 60cmx 6mm burried directly in ground vertically (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the earth plate at a depth not less than 1.5m below normal ground level connected to GI strip of size 32 x 6 mm (upto 7.5m long) by means of GI nuts, bolts and washers and 50 mm dia GI pipe light grade for protection of earth lead and 20mm dia GI pipe medium grade (upto 7.5m long) for watering arrangement and GI funnel all as specified and shown in Electrical Plate No 3 of MES Schedule Part I including necessary excavation and earth work in any type of soil, charcoal, dust salt, PCC 1:2:4 type B1 in chamber, 40mm thick RCC 1:2:4 type B1 in cover slab with 8mm dia TMT bars at 100mm C/C both ways and with 8mm dia MS hook complete and testing complete all as specified and as directed.

Supply , install ,test and commission CPRI APPROVED Outdoor floor mounted , totally enclosed cubical type , factory made confirming to protection class IP 54 of IS 2147 of 1967 ,LT panel board 3 phase 4 wire system ,double door front and back opening type , sloped canopy (Hood) on top extended 100 mm alround ,seperate compartment for each control gear ,cable alley ,provision of knock out type plates for various sizes of cable up to 185 sqmm 3.5 core in and out , incoming and outgoing feeders duly marked on revited plates etc complete factory fabricated made out of CRCA sheet 3 mm thick duly treated through 7 tank pre treatment process and painted with epoxy powder coated matt finish of SIEMENS GREY structural RAL 7032 shade colour , built in industrial type locking arrangement on front and back and prewired with FRLS PVC insulated multi stranded copper conductor for controls and monitors ,PVC sleeved aluminium strip for connecting MCCBs ,Panel mounted on Angle iron frame of 50x50x6 mm thick duly painted and embedded in PCC 1:3:6 ,45 cm below ground level and 15 cm above ground level and consists of the following ;

(a) Bus bar chamber with alunimium bus bar 400 amps duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size of F class insulators

(b) In coming : MCCB 250 amps 4 pole 415 volts 50 Hz thermal and fixed magnetic setting type with rupturing capacity 36 KA -1 No Make : Siemen/Schneider/ABB

(c) Outgoing : MCCB 160 amps 4 pole 415 volts thermal and fixed magnetic setting type with rupturing capacity 25 KA -02 Nos Make : Siemen/Schneider/ABB

(d) Outgoing MCCB 100 amps 4 pole 415 volts thermal and fixed magnetic setting type with rupturing capacity 25 KA -02 Nos Make : Siemen/Schneider/ABB

(g) LED phase indication lamp R,Y,B for incomer and outgoing switches - 3 Nos Make :L7T/Siemen/Legrand

Material and labour for Servo controlled Voltage stabilizer of capacity 35 KVA , air cooled for automatic operation, three phase indoor type & designed for input variation between 340 V to 480 V with output voltage stabilized at 415 V with accuracy ± 2.5% and speed correction desired Volts per second with all accessories complete all as specified and as directed. Note :Make of Voltage stabilizer : AE/ V GUARD / VINITEC/SINETRAC

Material and labour for Sub main wiring with 4 runs of single core FRLS PVC insulated unsheathed multistranded copper conductor cable of size 10.0 Sq mm drawn through and including PVC casing capping of suitable size with all necessary fittings and provn of two run of 10.0 sqmm FRLS PVC insulated unsheathed multistranded copper conductor double core cable as earth continuity conductor and connected to common earth dolly complete all as specified and as directed. Note :- (i)04 run of 10.0 sqmm and 02 run of 10.0 sqm including 01 run of PVC casing and capping will be measured as one length (ii) Make of PVC cable : Finolex/Polycab/RR Kabel . (iii) Make of PVC casing and capping :Avon plast/Presto plast/Garware

Supply and fix Factory made Epoxy powder coated distribution board double door TPN 4 ways (VTPN MCB DB) with metal door (IP-43 protection) fabricated from 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, neutral bar, strandard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with Knockouts and suitable for one FP MCCB/MCB 100/ 63 Amps as incomer and SP/TP MCBs (or any combination of SP/TP MCBs ) as outgoing complete all as specified and as directed. Note :Make of DB : Legrand/Siemen/Indo Asian

Supply and fix in replacement MCCB,4 pole,100 Amps , Rupturing capacity 16 KA current rating conforming to IEC-609472 & IS-139473 to be fixed in distribution board complete all as specified and as directed. Note :Make of MCCB :Siemen/Schneider /ABB

Supply and fix in repair MCB TPN 'C' series 63 Amps, 415 volts, 50 Hz, Rupturing capacity 10 KA complete all as specified and as directed. Note :Make of MCB : L&T/Siemen /ABB

Supply and fix MCB SP 240 Volt of capacity 6 to32 Amps ‘C’ seriescomplete all as specified and as directed. Note :Make of MCB : L&T/Siemen /ABB

Supply and lay GI pipe light grade 40 mm dia with all fittings & fixed complete fixed on pole/walls/in road etc for cable protection complete all as specified and as directed . Note :Make of GI pipe :Tata/Jindal/Prakash surya .

Material and labour for Point wiring complete with 1.5 Sq mm single core FRLS PVC insulated unsheathed 1100 volt grade copper conductor multi-stranded cables drawn through and including PVC casing capping of suitable size with all necessary fittings and provision of one run of copper conductor multistranded unsheathed FRLS PVC insulated single core cable of size 1.5 sqmm and connected to common earth dolly including 2nd HW box with sunmica top cover for mounting switches/sockets etc for the following points complete all as specified and as directed. Note :- (i) Make of PVC cable : Finolex/Polycab/RR Kabel . (ii) Make of PVC casing and capping :Avon plast/Presto plast/Garware

(a) One light point controlled by one switch 1 way.

(b) One light point controlled by two 2 way switches.

(c) One Ceiling fan/exchaust fan point controlled by one switch and regulator.

(d) One bell point controlled by one bell push.

(e) One 05 Amps socket outlet on independent board.

(f) One 05 Amps socket outlet on the same board with other switches.

Material and labour for Point wiring complete with 2.5 Sq mm single core PVC insulated unsheathed 1100 volt grade copper conductor multi-stranded FRLS cables drawn through and including PVC casing capping of suitable size with all necessary fittings and provision of one run of copper conductor multistranded unsheathed pvc insulated single core cable of size 2.5 sqmm and connected to common earth dolly incl 2nd HW box with sunmica top cover for mounting switches/sockets etc, complete all as directed. (For 15 Amps) Note :- (i) Make of PVC cable : Finolex/Polycab/RR Kabel . (ii) Make of PVC casing and capping :Avon plast/Presto plast/Garware

Supply and fix Switch piano type 5 Amps flush button 230 volts AC one way complete all as specified and as directed. Make : Anchor/Legrand /Leader

Supply and fix Switch piano type 5 Amps flush button 230 volts AC two way, complete all as specified and as directed. Make : Anchor/Legrand /Leader

Supply and fix bell push flush type AC 230 Volts 5 Amps, complete all as specified and as directed. Make : Anchor/Legrand /Leader/Rider

Supply and fix Socket outlet 15 Amps 3 and 5 pin 5 and 15 Amps flush type multipurpose, complete all as specified Make : Anchor/Legrand /Leader

Supply and fix Switch piano flush type 15 Amps 230volts, complete all as specified and as directed. Make : Anchor/Legrand /Leader

Supply and fix Call bell ding dong AC 230 volts, single pole complete all as specified and as directed. Make : Anchor/Legrand /Leader/Rider

Supply and fix Ceiling rose 3 terminal ,Poly carbonate body suitable for 230 volts AC supply, complete all as specified and as directed.Make : Anchor/Legrand /Leader

Supply and fix fan regulator electronic step type suitable for 1200/1400 mm sweep ceiling fan complete as specified Make : Anchor/Legrand /Leader/Rider

Supply and fix LED light fitting 4 feet white, 20W, integrated LED driver etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size. complete all as specified and as directed. Make:- Philps Cat Part No. BN021C LED20S PSU CDL GR or M/S Wipro Cat Part No D532065 20W-6500K

Supply and fix LED light fitting 2 feet white, 10W, integrated LED driver etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size. complete all as specified and as directed. Make:- Philps Cat Part No. BN 021 LED10S- 6500 PSU GR S1or M/S Wipro Cat Part No D531065 10W-6500K

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed Make:- Philps Cat Part No. BRP050 LED036 PSU GR or equivalent in M/S Wipro/CG

Supply and fix Single pole and neutral enclosure with a 2 pin & earth plug and socket complete with one Single pole MCB 20 Amps complete all as specified and directed . Note :Make : L&T/Indoasian/Siemen

Supply and fix Exhaust fan made out of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm ,Heavy Duty and including making suitable arrangement for fixing the exhaust fan i.e.,making suitable holes,grouting , anchor fastener bolts etc and matching the surface with existing surfacecomplete all as specified and directed. Make : CG/Bajaj/Khaitan

Material and labour for Sub main wiring with 2 runs of single core PVC insulated unsheathed multi-stranded copper conductor cables of size 4 Sq mm drawn through and including PVC casing and capping of suitable size with all necessary fitttings and provn of one run of 4 sqmm pvc insulated unsheathed multistranded copper conductor single core for erth continuity and connected to common earth dolly, complete all as specified and as directed. Note :- (i)02 run of 4.0 sqmm and 01 run of 4.0 sqm including 01 run of PVC casing and capping will be measured as one length (ii) Make of PVC cable : Finolex/Polycab/RR Kabel . (iii) Make of PVC casing and capping :Avon plast/Presto plast/Garware

Taking down existing MCB DB alongwith MCBs & old wooden boards & making good to disturbed surfaces.

Supply and fix in repairs MCB DP 40 - 63 A 10KA B series 50HZ AC supply including dismantling old one and taken as credit complete all as specified and as directed. Make : L&T/Siemen/IndoAsian

Supply and fix in repairs MCB DB SPN 12 way with 100 Amps rated bus bar double door type and including 2nd class hard wooden box 4cm depth with sunmica top of suitable size to fix the MCB DB, complete all as specified and as directed. Note :Make : L&T/Indoasian/Siemen

Supply and fix in repairs MCB 415V 10KA 'C' curve of following poles and current carrying capacity in the DB complete with connection testing and commissioning of capacity DP 25 to 32 Amps complete all as specified and as directed . Note :Make : L&T/Indoasian/Siemen

ASHIRWAD ELECTRICALS

M/s.GOODWILL ELECTRICALS

M G KANADIKAR ENGINEERS AND CONTRACTORS