Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | 1₹8.5 LAccepted-Finance 39 39 THANGAMAPURI PATTINAM METTUR DAM 636402 | SALEM | TAMIL NADU | 636402 | 1 | Accepted-Finance SATISFIED |
Tender Value
₹12.0 L
EMD Value
₹12,100
Closing Date
19 Oct 2020, 2:00 pmClosed
SE/M-II/MTPS-I
Superintending Engineer Mechanical-II Mettur Thermal Power Station-I Mettur Dam- 636406 Salem District
MTPS I CHP I Assistance for carrying out cold vulcanizing of belt joint in various width conveyors Belt Feeders Dribble conveyors in CHP I area
2020_EB_181933_1
SE M II MTPS I CHP I OT 94 2020 2021
Open Tender
Miscellaneous Works
Works
120 days
MTPS-I
As per Tender Specification
6 documents required · 6 mandatory
₹0
₹12,100
Yes
27 Oct 2020
3 Oct 2020
20 Oct 2020
3 Oct 2020
19 Oct 2020
3 Oct 2020
Amount
For 1400 mm / 1600 mm width conveyor Belt work in conveyor 1 to 4, 6A, 6B, 7A, 7B, 8A1, 8B1, R1&R2. Charges for arranging chain block and belt clamp in conveyor lifting the counter weight box assembly and normalizing the counter weight box assembly after completion of work.
Charges for removing idler, idler frame, cutting removal of wornout/damaged joint/excess elongation of belt, pulling, positioning the belt ends. Arranging platform. Assistance for making 1 No. cold vulcanizing joint. After completion of work, releasing belt clamp, fixing idlers, idler frame and conduct trial run of the conveyor
Charges for transporting, positioning new conveyor belt drum. Arranging pulley and rope. Cutting and removal of wornout/damaged belt from conveyor. Releasing the belt from drum. Leading, lifting, laying and tensioning the conveyor belt. Rolling the released wornout damaged belt. Devoluting the belt scrap to Central Stores/MTPS.
Charges for adjusting the tension screw, positioning the tail pulley. Removing idler, idler frame. Cutting, removal of wornout/damaged joint/excess elongation of belt, pulling positioning the belt ends. Arranging platform, clamps, assistance for making 1 No. cold vulcanizing joint. After completion of work releasing belt clamps, fixing idler, idler frame and normalizing tension screw and conducting trial run of R1/R2 Conveyors.
For 1800mm width conveyor belt work in tunnel area. For belt feeder 1 to 4, 6A & 6B. Charges for dismantling Belt Feeder pulley hood, skirt board, cutting removal of wornout/damaged belt. Removing idler, idler frame. Adjusting the tension screw and position the tail pulley. Cutting removal of 11.5 mtr/12mtr x 1800mm width new conveyor belt from roll, transporting, leading, lowering to Belt Feeder tunnel floor. Removing belt scrap from tunnel area and devoluting to Central Stores/MTPS. Laying new belt on Belt Feeder. Clamping the belt. Assistance for making 1 No. cold vulcanizing joint. After completion of work releasing belt clamps fixing idler, idler frames, skirt board, pulley hood etc., adjusting the belt tension and trial run of the Belt Feeder.
Charges for providing 3 Ton chain pulley block, lifting the non-drive pulley along with two piece pillow block. Dismantling the wornout belt-tensioning device – 2 Nos. replacing new / serviced belt tensioning device – 2 Nos. in position and erection of non-drive pulley along with two piece pillow block. Aligning the belt-tensioning device by checking water tube level on the both ends. Tightening the bolts and nuts and removing the chain block.
For 2000mm width conveyor belt work in tunnel area for dribble conveyor 1,2,3,4 Charges for removal of skirt board, cutting removal of wornout belt of size 2000mm x 30mtr from dribble conveyor, leading, lifting the belt scrap from tunnel area to ‘O’ mtr. ground floor and devoluting to Central Stores / MTPS. From 2000mm width belt roll cutting removal of 30 mtr belt, leading lowering to the dribble conveyor tunnel working area. Adjusting the tension screw, position the pulley, laying new Conveyor belt of size 2000mm width x 30 mtr length in Dribble Conveyor of Apron Feeder. Clamping the belt. Arranging plat form. Assistance for making 1 No. cold vulcanizing joint. After completion of belt joint removing belt clamp, fixing skirt board, adjusting the tension screw, tensing the belt and trial run the dribble Conveyor.
Charges for decoupling the slow speed coupling from gear box to head pulley and removal of flexible rubber elements and assembling the coupling after completion of belt joint work (damaged flexible rubber element has to be replaced by new one) and all bolts tightening checking etc. including cost of T&P’s and consumables.
Charges for removing the coal slurry from sump pump storage tank, loading the coal slurry in to the adjacent running conveyors, dismantling, choke releasing and cleaning the sump pump suction and discharge pipe lines and normalizing the same in conveyor 5A, 6A/6B, 7A/7B tunnel area.
stage.html
html • 0.03 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .