Construction of 50 Bedded Critical Care Hospital Block Hospital under Phulo Jhano Medical College at Dumka District.

Amount

Earth Work in excavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I

Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B)

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diaMTR.er holes and plugging with cement mortar 1:2 (1 cement : 2 Coarse sand) to match the existing floor With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concete of soecified grade excluding the cost of centering and shuttering - All work up tp plinth level 1:4:8 (1 cement :4 coarse sand (Zone -III) :8 graded stone aggregrate 40 mm normial size)

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).

REINFORCED CEMENT CONCRETE

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately).

All works upto plinth level

All works above plinth level upto floor V level

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ)

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 10mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 12mm. to 32mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

BRICK WORK

Providing designation 75A work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.m. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials ranking out joints to 15mm depth, curing taxes and royalty all complete as per building specification and direction of E/I.

providing designation 75 B brickwork in C M ('1 :6 ) in foundation and Plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing. taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 100A brick work with flyash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints costs of screening materials, raking out joints to 15mm depth curing taxes and royalty all complete as per building specification and direction of E/I.

Providing Designation 100A B/W with Fly Ash Lime Brick (FALB) conforming to IS 12894-1990 (9"x4.5"x3") in cement mortar (1:6) in Superstructure with clean coarse sand of F.M. 2 to 2.5 including 10mm thick mortar joints,cost of screening, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 112mm thick reinforced designation 100A brick work with flyash lime brick (FLAG) in (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening carriage of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

Extra for providing & placing in position 2 no 6mm dia ms bar every 3rd corse of half brick masonary

DOOR WINDOW WORK AND STEEL WORK

Providing and fixing pressed steel door confirming IS code 4351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by . mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock abJSORbers as specified and applying a coat of approved steel primer after pre- treatment of the surface as directed by Engineer-in-charge: Profile B

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with one sides teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured):

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accesJSORies and screws etc. complete.

Providing and fixing aluminium tower bolts ISI market anodised (anodic coating not less than grade AC 10 as per IS: 1868) trasparent of dyed to required or shade with necessary screws etc complete. 100 x 10 mm

Providing and fixing alluminium hanging floor door stopper anodized (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc.complete:Single rubber stopoper

Supplying,frtting and fixing M.S. grill made of 20x6cmm M.S. flat as per approved design and drawing, properly fabrlcated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/1

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladders, railings, brackts. gates & similar works.

Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of E/I.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accesJSORies & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accesJSORies such as nuts, bolts, fasteners etc.).

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame

30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge..

FLOORING WORK

Providing and laying 25mm. thick kotah stone slab flooring of approved size, texture and colour over 19 mm thick base of lime morter (1:l:1) ( Lime putty : surkhi: coarse sand ) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to granolithic finish with approved quailty of carborandum stone including cost of curring, taxes and royalty all complete as per building specification direction of E/I. 600x600mm Size.

Providing and laying 25mm. thick kotah stone riser of steps, skirting and pillers of approved size, texture and colour over 12 mm thick cement morter (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to granolithic finish with approved quailty of carborandum stone including cost of curring, taxes and royalty all complete as per building specification direction of E/I. 600x600mm Size.

Providing and fixing Ist quality ceramic glazed wall tiles conforming toIS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer )with water abJSORption less than 0.08% and conforming to IS:15622 / ISO 13006 of approved make , in all colurs and shades, laid on 20mm thick cement mortor 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complete Size of Tile 600mm x 600mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels..Area of slab over 0.50 sq

Extra for providing edge moulding to 18 mm thick marble stone counters, Vanities etc. over item no. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in -charge.Granite work

Extra for providing opening of required size & shape for wash basins/kitchen sink in kitchen platfometre. Vanity counters and similar location in marble/stone work including necessary holes for pillar taps etc. including rubing and polishing of cut edges etc. complete.

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).Light shade pigment using white cement

52mm thick cement concrete flooring with metallic concrete hardener topping under layer 40 mm thick cement concrete 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick metallic concrete hardener consisting of mix 1:2 (1 cement hardener mix:2 stone aggregate 6 mm nominal size) by volume @ 2 liter per 50 kg of cement or as per manufacture specification. This includes cost of cement slurry, etc. but excluding the cost of nosing of steps etc. complete

ROOFING AND WATERPROOFING

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of: (i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming tc IS 2645 in recommended proportions.(ii) 11 nd course of 20 mm cement plaster 1:3 (1 cement:3 coarse sand)mixed with water proofing compound in recommended proportion, (iii) Illrd course of applying blown or/residual bitumen aplied hot at 1.7 kg. per sqm of area, (iv) Ivth course of 400 micron thick PVC sheet.(Overlaps at joints of PVC shet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqni).

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12 mm dia steel bar conforming to IS: 1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specification and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15cm cement concrete block 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size) complete as per design.

FINISHING WORK

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty as per building direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 1.5mm cement punning including curing carriage of water with all leads and lifts as per building specification and direction of E/I.

Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing and applying Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade.New work (two or more coats) over and including water tinnable priming coat with cement primer

Providing and applying With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre

Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade :

New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

Providing two coats of oil bond Distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone of fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification direction of E/I

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification and direction of E/l.

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

ALUMINIUM WORK

Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.)

Supplying, fitting and fixing M.S. grill gate with M.S. grill made of 20X6mm M.S. flats or 16mm M.S. square bars fitted on 25X25X6mm M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately):For fixed portion.Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutter of doors, window & ventilators including providing and fixing hinges / privots and making provision for fixing of fitting wherever required including the cost of EPDM rubber / neoprene gasket required ( fitting shall be paid saparatly )Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I.

wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with

Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of GI sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. sqm 1357.90

LIFT Passenger lift (Bed lift) capacity 20 persons, wt-1360kg, G+4

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all omplete as per the direction of Engineer-in-charge.

Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing Retro-reflective regulatory sign board of size 900 mm dia meter made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type retro -reflective sheeting as approved by Engineer-in-charge . Letter, symbols, borders etc. will be as per IRC - 67 with required colour scheme onthe boards and with the high intensity grade A. The aluminium sheet to be riveted to M.S. frame of angle iron of size 40x40x4 mm. The boards will be fixed to 1 No. 50x50 mm square post made of M.S. angle 50x50x4 mm, 4 m long welded to the frame with adequate anti-theft arrangement .Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per direction of Engineer-in-charge.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge 100 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range5 cm to 20 cm, in recharge pit, in the required thickness, for allleads & lifts, all complete as per direction of Engineer-in-charge

Supplying, filling, spreading & leveling gravels of size range 5 mm to10 mm, in the recharge pit, over the existing layer of boulders, inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge

DT : Basic rates for 125/115mm dia drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of E/I.. (Basic Rates) Drilling upto 30 mtr. Depth below G.L. in Rural Area

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 14.14.2-150 mm dia

CARRAIGE OF MATERIAL

BRICKS ( 7+1 KM )

STONE METAL (22 KM)

CHIPS ( 22KM )

SAND ( 10KM )

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Providing and fixing of Stainless Steel (304 grade) Aldrop size of 14 mm dia & 250 mm long with necessary screws etc. complete as per design & approved by Engineer in Charge.

Providing and fixing of Stainless Steel (304 grade) Aldrop size of 14 mm dia & 200 mm long with necessary screws etc. complete as per design & approved by Engineer in Charge.

Providing and fixing of Stainless Steel (304 grade) Handles size of 10 mm dia & 128mm long with necessary screws etc. complete as per design & approved by Engineer in Charge.

Providing and fixing of Stainless Steel (304 grade) Handles size of 32 mm dia & 600mm long with necessary screws etc. complete as per design & approved by Engineer in Charge.

Water proofing for Old and New Roof Slab :- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed ready to use, acrylic modified flexible material applied with brush, roller or spray for water proofing coating as per manufacturer specifications with following steps :- (a) Surface preparation :-Providing and cleaning of concrete surface to remove dust, oil, grease including removal of existing loose paint / coating, and cement laitance by cleaning with compressed air & water jel including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage, leakage. On identification of seepage, cement grouting to be done with non shrink expanding admixture of Sika lndia Pvt.Ltd. / MYK Schomberg / Dr Fixit/Fosroc or equivalent. Providing and reparing of all corners and joints such as those between the parapet wall and the roof slab etc shall be chamfered with '150mm X '150 mm fillet of mortar (Cement: sand - 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent. Before chamfering a prime coat shall be given with the slurry of acrylic polymer Repairing surface irregularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modilied repair mortar including a coat of bonding agent of the same with cement slurry including all material, labour, tools complete.

(b)1st Coat :- Apply 1st coat of two component acrylic modified, ready to use, flexible cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600 mm by brush or roller. After 1st coat of application ,45 gsm oI Fibre glass cloth to lay when the first layer is still green. 1st coat should be applied @1.50 kg/Sqmt/coat. For the purpose of measurement the entire treated surface will be measured." (c) 2nd Coat :- To apply the 2nd coat of two component acrylic modified, ready to-use, flexible cementitious material right angle to the 1st coat over the glass fibre laid surface. 2nd coat should be applied @0.7 kg/ Sqmt/coat. For the purpose of measurement the entire treated surface will be measured." After three days of drying the 2nd coat , the rain water outlets to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectification to be done as per satisfaction of E/C. The waterproof coating to be protected from damage before screed over it. Waterproofing Brand: Sika Topseal 109hi / Fosroc Brushbond RFX/ Dr Fixit Pidiffin 2K/MYK Aquafin TG Product Performance - Chemical Base Part A. Acrylic copolymer, Part B Specially graded cementitious powder - Density 1.6 kg/l (mixed density) at +27°C Tensile Strength - 2 N/mm2 after 28 days (with Fibre cloth) (According to ASTM D 2370) Pullout Bond Strength-2 N/mm2 (concrete failure) (According to ISO 4624) Slant-Shear Bond Strength ~4N/mm2 (According to FIP 5.15) Elongation at Break ~35% without Fibre Cloth and 20% with Fibre Cloth (According to ASTM D 2370)

(d) Protection of treated surface with PCC :- The treated surface should be covered with 25mm/50mm PCC of M-20 grade(1:1.5:3) with proper slope (1:120) towards tlre rain outlets in alternate panels of 2 mlx2ml keeping 6mm gap between the panel joint. lntegral water proofing admixture conforming to lS 2645 @ of 100 ml per bag of cement to be added in the screed concrete (paid separately for this ltems).-All corners shall be chamfered vrith 150mm X 150 mm fillet. The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - the peripheral gaps between pvc pipe outlet and concrete surface should be packed properly with rich concrete and the peripheral mouth to be sealed with moisture insensitive epoxy putty of Sika lndia Pvt.Ltd / MYK Schomberg / Dr Fixit/Fosroc. For the purpose of measurement the entire treated surface will be measured." (e)Groove of PCC surface should be filled with Polysulphide Sealant (Paid Separately) Brand - Sika lndia Pvt Ltd / MYK Schomberg / Dr Fixit/Fosroc. Warrenty for five years.

Covering of treated surface with PCC :- Providing 50 mm thick Cement Concrete M20(1:1.5:3) rnaintaining slope in alternate 2 mt x 2 mt panels with aaproved quality of stone chips of 20 mm to 6 mm size graded and cleaned sand of F M 2.5 to 3 including screening,shuttering,and mixing cement concrete in mixer with admixture of integral water proofing and placing in position, striking curing, taxes and royality all complete as per building specification and direction of E/I. Panels that has been left should be casted next day. There should be 6 mm gap between Panels . Brand-Sika-Plastocrate plus, MYK proof WP 10, Fosroc-Conplast X 4211C, Dr.fixit Pidiproof LW+ or Equivalent

Providing and filling of 6mm Groove between 50 mm PCC Panels with 6 mm thick 25 mm deep thermocol strip and filling the rest 25 mm with Polysulphide Sealant (Poring Grade)as per drawings and technical specifications and direction of Engg in Charge.(with 18% GST). Brand.-Sika-Polysulphide , Fosroc-Thioflex 600,Dr. Fixit Pidi Seal PS(42P),MYK Seal PS or Equivalent.

Providing and mixing Liquid lntergral water proofing compound in Concrete or plaster as per manufacturer specification and as per direction of Engg - in Charge. Brand- Sika Plastocrate plus, MYK proof WP 10, Fosroc-Conplast X 4211 C, Dr fixit Pidiproof LW+ or Equivalent .

Skylight ( poly corbonate sheet):- Supply and installation of 2 mm thick clear embossed polycarbonate sheet (sabia india make) (polycarbonate profile to match with standing seam profile with side laps to be clamped with bare galvalume sheets of 0.55mm (tct), which can be further seamed with metal roof sheets. Product required is clear embossed with both sides UV stabilizer, having at least 60-80% transparency, conforming to the relevant IS code including cutting to shape and size as required including necessary sealants (silicon sealants/ butyl sealants for transverse laps). Including all materials, tools and tackles, labour etc. required for completing the work in all respect as per direction of engineer in-charge.

Providing & Fixing flexible Conductive PVC sheet flooring of Armstrong/ Forbo/ Polyflor having a total thickness of 2mm and weight of 3kg/m².Colors and pattern detail shall be dispersed throughout the thickness of the wear layer. It shall conform to Group P of Wear Resistance as per EN 649, Flammability of class Bfl-s1 as per EN 13501-1, Slip resistance as per DIN 51130 group of R9 , having REACH Registration No, 1907/2006 contains no substance mentioned in SVHC list. Impact sound reduction of 3 dB as per ISO 140-8, Residual indentation of 0.05 mm as per EN 433, Color fastness rating ≥6 as per ISO 105-B02, Vertical resistance(R1) less than 1 x 10⁶- 1x 10⁸Ω as per EN 1081, and surface resistance less than 1 x 10⁶- 1x 10⁸ Electrical insulation to ground greater than 50 kΩ as per VDE 0100, Static electrical charge of ≤2.0kV as per EN 1815, Thermal resistance of 0.04m²K/W as per EN 12667, Thermal conductivity of 0.25 W/mK. Equivalent to Armstrong PASTELL. Installation:It is important to ensure the sub floor on which the sheet is being laid is smooth, flat & hard & free from moisture, grease, etc. In case of uneven sub floor the same should be leveled by self leveling compound. The moisture level present in the subfloor should be less than 8% before installation of the floor. The sheet should be laid using adhesive recommended by company.Each row of tiles/strip of floor covering must be linked crosswise with a continuous copper strip. Individual rows/strips must be at least 3 m² in size and linked to the rest of the area with a copper tape. In rooms of up to 40 m², connection points for equipotential bonding should be provided in at least one point in the room. Approv make- Armstrong, Polyflor, Forbo

Supply and installation of Wallflex PUR Vinyl Sheet wall covering manufactured by Armstrong World Industries, Inc, 1.5m wide, having a nominal total thickness of 1mm. The nominal thickness of the wear layer would be 1mm. The wear surface shall consist of impregnated polyurethane homogeneous mixture of PVC, Plasticizers, Urethane, color pigments and filler calendared to form a sheet. Colors shall be dispersed throughout the thickness of the wear layer. Wallflex shall conform to Group M of Wear Resistance as per EN 660-2, Fire resistance of group 2 as per AS/NZS3837, Residual indentation of ≤0.10mm as per EN433, curling after exposure to moisture ≤8mm as per EN434, Seam strength of mean≥240N/50mm as per EN684.Make of : Armstrong/Polyflor/Forbo

Supply and installation of PVC sheet flooring 2 metre wide and overall thickness of 2mm of Armstrong/ Forbo/ Polyflor. The product should be homogeneous and single layered. The wear surface shall consist of impregnated polyurethane homogeneous mixture of PVCwith DIAMOND 10 technology, Plasticizers without DOP, Urethane, color pigments and filler calendered to form a sheet. Product shall conform to group "T" wear resistance as per EN 649, Flammability resistance of class Bfl-s1 as per EN13501-1, Dynamic coefficient of friction of class DS as per EN 13893, Impact sound reduction of 3dB as per ISO 10140, Slip Resistance of class R9 as per DIN 51130, Color fastness rating of ≥6 as per ISO 105-B02, total weight being 3.3 kg/m2 as per EN430. The product shall be suitable for applications in class 23/34/43 areas as per EN685. Product shall exhibit antistatic behaviour, resistance to bacteria,resistance to chemical, resistance to staining,suitability to castor chair. Equivalent to Armstrong Simpurity Installation- It is important to ensure the subfloor on which the sheet is being laid is smooth, flat, hard and free from moisture, grease etc. In case of uneven subfloor the same should be levelled using self leveling compound which will charged extra. The moisture present in the subfloor should be less than 8% before installation of the floor. dhesive. The installation shall be undertaken as per manufacturers installation instructions.

Providing & Fixing of Flocked textile linear floor covering of Nylon 6.6 face fiber or equivalent of approved make with 100% Nylon and completely water proof resilient backing. The flooring should be Anti static with thickness of 4.3 mm and approximate weight of 1.8 k.g./sqm of roll form. The carpet should be completely stain resistant and of a density approx. 80 million fibers/sq.mtr (70 million fiber/sq.yd) in the width of 2 mtr .The floor covering should have Fire Test EN-13501, Appearance Retention Hexapod ISO 140-8, Friction Slip Resistance Test EN 14041 Class DS, with resilient waterproof backing, anti allergic which is certified by British allergy foundation. The carpet should have permanent static control & should be fixed with powder coated aluminum angles as per detail. Aluminum angles to be paid separately. The work should be carried out by the authorized installer of the Company in India.

Providing and laying of 2 - 3 mm average thick layer of cementations smoothening compound of UZIN NC 149 sh or equivalent as recommended by the Vinyl sheet flooring manufacturer over and including a priming compound of UZIN PE 360 sh or equivalent as recommended by the Vinyl sheet flooring manufacturer and installation team on concrete surface to provide a smooth & homogenous surface for laying of vinyl sheet flooring complete to the entire satisfaction of Engineer-in-charge.

Providing & fixing Rockfone Stonewool Acotsical Ceiling PACIFIC High NRC (0.80), Fire Rating A1 (EN 13501-1), RH 100% (No visible deflection in high humidity), Superior Class Light Reflection, Sag Resistant 12mm thick Ceiling Tiles of size 600x600 A-Edge (Square) with AntiBacterial Properties & M1 Class Emission Certification made up with Natural Stone (Bassalt Rock) a complete Green Product & perfect suitable for any kind of False Ceiling application in builiding & costruction. The Visible side is a smooth white painted fleece, the Rear side: back fleece with complete facctory finish Painted edges.

DEEP BORE WELL

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

(c) From126.0 M to150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump.Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP

Supply fitting and fixing of standered make starter pannel Board with arrangement of all necsssury protection including all taxes , all complete job as per direction of E/I.

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I.

Supply fitting and fixing lowering 40 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I.

PLUMBING WORK

SUBHEAD-I (A): SANITARY INSTALLATIONS

Supplying fitting and fixing 40mm high vitreous white glazed earthen E.W.C. With 'P' trap of parry hindustan or any other approved I.S.S. Make including supplying and fixing 15 litres C.I. Mosquito proof low down flushing cistern of approved make with complete fittings With C.I. handle and R.S. or bracket with telescope flush pipe with brass coupling and plumbers joints spindle stop cock of approved uality weight not less than 450grams 15mm P.V.C. alkathene pipe 45cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved pain over a coat of red oxide priming all complete as per specification and direction of E/I.

(ii) E.W.C. With 'S' trap

(b) 10 lit. Low level PVC Cistern

Supplying fitting and fixing white glazed fire’s clay sink of approved make with overflow arrangements supported on C.I. or R.S. painted brackets 40mm. dia C.P.brass waste with C.P.brass chain and rubber plug 40 mm dia P.V.C. waste pipe about 750mm long with brass coupling at one endand 15mm C.I. body brass spindle bib cock of approved quality of weight not less than 450grams. including cutting wall and making good the same etc. all complete as per specification and direction of E/I.

(i) Kitchen sink 600 mm x 450 mm x 250 mm

Providing and fixing white vitreous china laboratory sink with CI brackets , C.P brass chain with rubber plug 40 mm C.P brass waste and 40 mm CP brass trap with necessary C.P brass unions complete including painting of fittings and brackets , cutting and making good the wall wherever required :

Size 600x450x200 mm

Providing & fixing PVC waste pipe for sink including PVC waste fitting Complete

Flexible Pipe

32mm Dia

White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Rectangular shape 453x357 mm

Rectangular shape 1500x450 mm

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms.

Providing & fixing PTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealed fittings arrangement of approved quality and colour weighing not less than 88 gms

Providing and fixing C.P. brass bib cock of approved quality confirming to IS:8931

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

15mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore.

15 mm nominal bore

Providing and fixing toilet paper holder :

C.P. brass

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone finished smooth aggregate 6 mm nominal size) as per direction of Engineer-in-Charge and

Granite Stone of approved shade

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete

SUBHEAD-II(A): INTERNAL DRAINAGE INSTALLATIONS

Providing and fixing cast iron trap of self cleansing design with cast iron screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors.

100 mm inlet and 100 mm outlet

Sand Cast Iron S & S as per IS:3989

100 mm inlet and 75 mm outlet

Sand Cast Iron S & S as per IS:3989

Providing and fixing soil, waste, vent and rain water pipes

Centrifugally cast (spun) iron S&S pipe

100mm dia cast (spun) iron S&S pipe

75 mm dia cast (spun) iron S&S pipe

Providing and fixing MS holder bat clamps of approved design to cast iron (spun) pipe embedded in and Including cement concrete blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc.

For 100 mm dia. Pipe

For 75 mm dia. Pipe

Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete.

100 mm dia

Centrifugally cast (spun) iron pipe S&S

75 mm dia

Centrifugally cast (spun) iron pipe S&S

Providing and fixing plain bend of required degree.

100 mm dia

Sand cast iron S&S as per IS : 3989

75 mm dia

Sand cast iron S&S as per IS : 3989

Providing and fixing heel rest sanitary bend,

100 mm dia.

Centrifugally cast (spun) iron pipe S&S

75 mm dia.

Centrifugally cast (spun) iron pipe S&S

Providing and fixing terminal guard:

Sand cast iron S&S as per IS - 3989

Sand cast iron S&S as per IS - 3989

Providing and fixing collar.

Centrifugally cast (spun) iron pipe S&S

Centrifugally cast (spun) iron pipe S&S

Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work :

100 mm dia cast (spun) iron S&S pipe

75 mm dia cast (spun) iron S&S pipe

SUBHEAD-III(A): WATER SUPPLY INSTALLATIONS

Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in charge. Internal work -Exposed on Wall

15 mm nominal outer dia pipes

20 mm nominal outer dia pipes

25 mm nominal outer dia pipes

32 mm nominal outer dia pipes

40 mm nominal outer dia pipes

50 mm nominal outer dia pipes

Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the wall same including testing of joints complete as per the direction of engineer incharge Concealed work including cutting chases and making good the wall etc.

15 mm nominal outer dia pipes

20 mm nominal outer dia pipes

25 mm nominal outer dia pipes

32 mm nominal outer dia pipes

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.

FIRE FIGHTING WORKS

SUBHEAD-II(B): FHC AND PIPING FOR FIRE FIGHTING SYSTEM

Doors and frame

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single headed Gunmetal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. (INTERNAL FIRE FIGHTING)

20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585

20 mm nominal internal dia gun metal globe valve & nozzle.

Drum and brackets for fixing the equipmets on wall.

Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Gun Metal

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

Gun metal

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

100 nominal bore

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

Threaded joint upto 50mm diameter pipe.

Welded joint above 50mm diameter pipe.

25 mm nominal bore (class C)

32 mm nominal bore (class C)

40 mm nominal bore (class C)

50 mm nominal bore (class C)

65 mm nominal bore (class C)

80 mm nominal bore (class C)

100 mm nominal bore (class C)

Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

SUBHEAD-III (B) : SPRINKLER SYSTEM

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required :

Providing and fixing testing and commissioning of 15 mm size quartzoid bulb type sprinklers. Set to operate at

Providing, fixing, testing & commissioning of 15mm diaquartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :

UPRIGHT Sprinkler

Pendent Sprinkler and up right

side wall sprinkler

SUBHEAD- IV (B): FIRE EXTINGUSHER

Providing, storing, handling, shifting, installation, testing and commissioning of portable fire Extinguishers as described below:

4.5 kg carbon dioxide extinguisher, IS marked, with high pressure discharge tube, horn, control valve, CCE approved cylinder

6 kg Mono Ammonium Phosphate (ABC) type cartridge operated extinguishers

FIRE BUCKET WITH SAND WITH SET OF 4 PAIR

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required :

Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.

Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325.

M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.

Suitable cement concrete foundation duly plastered with anti vibration pads.

1620 lpm at 70 m Head (For Hydrant & Sprinkler System).

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump)

Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520.

Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325.

M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.

180 lpm at 70 m Head (For Hydrant & Sprinkler System).

WATER SUPPLY EXTERNAL

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.

External Work

25mm nominal nominal bore

32mm nominal nominal bore

40mm nominal nominal bore

50mm nominal nominal bore

65 mm nominal nominal bore

Providing & Fixing of Garden hydrant outlet consisting 1 No. 25mm dia. Ball valve,( Brass) for connecting rubber hose, pipes & fittings.

Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends)

20mm nominal bore

25 mm dia, nominal bore

32 mm dia, nominal bore

40 mm dia, nominal bore

50mm nominal bore

65mm nominal bore

Constructing masonry Chamber 60x45x50 cm,inside with 75 class designation brick work in cement mortar 1:5 (1 cement:5 fine sand) for water meter complete with C.I. Doble flap surface box 400x200x200mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size) necessary excavation foundation concret 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortor 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design.

With F.P.S. bricks

Providing and fixing GI pipes complete (IS:1239 Heavy Class) with GI fittings and clamps including MS pipe supports, enamel paint as per specifications cutting and making good the walls etc. complete.(WTP Room Abow the UGT.)

50 mm dia, nominal bore

65 mm dia, nominal bore

80 mm dia, nominal bore

Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality

50 mm dia, nominal bore

65 mm dia, nominal bore

80 mm dia, nominal bore

Providing and fixing G.I. union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete.

32 mm dia, nominal bore

40 mm dia, nominal bore

50 mm dia, nominal bore

65 mm dia, nominal bore

Providing & fixing in position precast RCC manhole cover and frame of reqd. shape and approved quality.

Circular shape 560 internal dia.

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) :

50 mm dia

Providing and fixing cast iron wafer type butterfly valves (PN-10) complete with 2 nos. matching flanges (Table-E),bolts, nuts, 3.0 mm thick insertion neoprene gasket.

40mm dia

50mm dia

65mm dia

80mm dia

Non - return valve with dual plate of CI Body SS plates vulcanized NBR seal flanged end & PN 16 rating as specified.

65mm dia.

Providing & fixing CI `Y' Strainer (screwed/ flanged) with stainless steel fine wire mesh perforated sheet basket with necessary flange/ unions nuts, bolts and washers complete as required.65mm nominal bore

Providing and fixing M.S fabricated hot dipped galvanized coating puddle flange comprising of 600 mm dia long M.S class 'B' pipe (screwed end up to 50 mm & flange for more than 50 mm dia) with 6 mm thick M.S plates of required size including cutting holes in centre of plate, inserting pipe & making welded (Arc) joint complete. Same shall be installed with TEC welded joint in position with reinforcement bars of RCC tank wall/slab including making cutout in shuttering during concrete casting of tank of following diameter. (Location: Underground / Overhead Tanks.)

25mm dia pipe, 600mm long with size of 250x250x6 mm MS plate

32mm dia pipe, 600mm long with size of 250x250x6 mm MS plate

40mm dia pipe, 600mm long with size of 300x300x6 mm MS plate

50mm dia pipe, 600mm long with size of 350x350x6 mm MS plate

65mm dia pipe, 600mm long with size of 350x350x6 mm MS plate

100mm dia pipe, 600mm long with size of 400x400x6 mm MS plate

150mm dia pipe, 600mm long with size of 450x450x6 mm MS plate

200mm dia pipe, 600mm long with 6 mm MS plate of size 600mm dia

Providing, laying, Jointing, Testing and commissioning of uPVC pressure pipes of 10Kg/Sqcm pressure rating class 5 (IS : 4985-2000) including fittings, tees, bends, clamps, coupling and adaptors supports, and jointing with solvent joint, testing and necessary earth work in excavation, backfilling, disposal of surplus earth with a lead upto 50m complete, compaction and consolidation Including laying cement concrete 1:2:4 alround UPVC pipe including bed concrete and thrust blocks at bends as per standard design.

RO SYSTEM

Supply, installation, testing and commissioning built with Drinking Water R.O. unit with micron filtration pre-treatment unit, skid mounted R.O. module with pressure pump and pressure tank, drinking water cooler (High quality SS Tank for Storage 80 lts) , complete in all respects. ( Make & Model No. Eureka Forbes Pure Chill RO Storage Cooler cum Purifier or Equivalent)

EXTERNAL SEWERAGE & DRAINAGE INSTALLATIONS UPTO MAIN ROAD FIRST MANHOLE

Earth work in excavation for laying of different types and sizes of R.C.C. spun pipes with disposal of excavated earth within initial lead and lift as per specification and direction of E/I.

All kinds of soil

(ii) For classification of soil item-B

Providing laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.

150 mm diameter

200 mm diameter

250 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) alround SW pipes including bed concrete as per standard design.

150 mm diameter

200 mm diameter

250 mm diameter

Providing and fixing square mouth SW gully trap grade ‘A’ complete CI grating brick masonry chamber with bricks of class designation 75 and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 13.00 kg and frame to be not less than 5 kg. as per standard design. (COVER MIN. 4.5 KG & FRAME MIN.2.7 KG )

150x100mm size P type With FPS bricks

Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete.

150 mm dia RCC pipe

250 mm dia RCC pipe

300 mm dia RCC pipe

450mm dia RCC pipe

Providing and laying in position cement concrete of grade excluding the cost of centering and shuttering - all work up to plinth level 1:5:10 (1 cement : 5 coarse sand : 10 graded ston aggregate 40 mm nominal size)

Construction brick masonry manhole in cement mortar 1:4 (1cement : 4coarse sand) RCC top slab with 1:2:4 mix 9 with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement : 2 coarse sand 4 graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design.

Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610mm internal dimensiions total weight of cover and frame to be not less than 38 Kg. ( weight of cover 23 Kg. and weight of frame 15 Kg.), with FPS bricks with class designation 7.5

Extra for depth for manholes

Size 90 x 80 cm with FPS bricks designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12 mm dia steel bar conforming to IS: 1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specification and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15cm cement concrete block 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size) complete as per design.

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :

For pipes 100 to 250 mm diameter

PUMPS & ALLIED WORKS

Providing, installing, testing and commissining of variable speed (VSPS) hydropneumatic system mounted on a common base plate comprising of vertical centrifugal pumping set with S.S body, stainless steel impeller and mechanical seal, shaft directly coupled to a TEFC induction motor suitable for 400/440 volts, 3 phase, 50 cycles AC supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundation, one No. microprocessor based controller, dedicated variable frequency drive for each pump, one No.remote sensors, pressure transducers, sequence running cotroller, dry running Protection,motor control centre, necessary power and control cabling from MCC to pumps including required rating of MCB, one No. 90 litre capacity M.S diaphragam tank with interchangeable butyl rubber membrane,complete in all respects including MS Zinc coated suction and delivery headers and isolation/ control valves( ball valves/butterfly valves/ Nan return valves/ vibration eliminators etc as required) , power box, equipped with fuses/ isolators/circuit breakers as required.

The entire Hydropneumatic system shall be factory fitted.

Hyd. System for Domestic Water Supply Pump

Flow rate : 2 lps each

Pumping Head - 70 m

1 Set = 2 Nos. pump (1 working+1 standby)

Approx H.P.- 3 HP or as per manufacturer recommendation.

Location - Abow UGT.

Flow rate : 1.5 lps each

Head : 70 Mts

Required for : Flushing water transfer pump

(1 working + 1 standby)

Location - Abow STP

Supplying, installing, testing and commissioning of SS vertical centrifugal pump. Each pump shall have TEFC 2900 RPM three phase electric motor. The pump shall have cast iron head, base plate SS Shaft / Impeller / Intermediate chamber along with motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, stainer (with by-pass) at suction. Pump shall be provided with mechanical seal, suitable vibration elimination pads of approved design, drain pipe with valve (25 dia). The pump shall be suitable for auto/ manual operation. The installation shall be complete with all necessary ancillaries, starter panel / control panel & accessories including base plate complete as required.

Flow rate : 2 lps each

Head : 70 Mts

Required for : Filter feed pump

(1 working + 1 standby)

Location - Abow UGT.

Providing, fixing, testing & commissioning of vertical FRP filter with adequate dirt holding capacity. Fabricated from FRP sheet as per IS-2825 and manufacturer's specifications complete with intitial charge filter media . The filter shall also be provided with set of internals for raw water inlet and bottom collecting system. Complete with frontal piping (PVC 10 Kg) and multiport valve . it is designed on 1.50 m / sec velocity.

WATER TREATMENT PLANT (WTP)

Dual Media Filter For Domestic Water Supply

Capacity- 7200 LPH

Filtration rate- 16000 LPH/Sqm.

Filter dia approx. - 750 MM

Working pressure: 3.0 Kg/sq cm.

Test pressure : 4. 5 Kg/sq cm

Activated Carbon Filter For Domestic Water Supply

Capacity- 2500 LPH

Filtration rate- 16000 LPH/Sqm.

Filter dia approx. - 750 MM

Working pressure: 3.0 Kg/sq cm.

Test pressure : 4. 5 Kg/sq cm

Treated water Pumps- Domestic water OHT Filling

Capacity : 150 LPM

Head : 70 m

App. HP : 3 HP

Motor RPM : 2900

Each set consists of 2 pumps (1Working +1Standby). At any given time, only one pump need operate. Both the pumps must operate alternatively in service.

Providing & fixing butterfly valve (with motorized actuator) of rating PN 1.6, wafer type, in cast iron body with Ductile Iron disc, EPDM seal, SS single piece shaft, conforming to IS-13095 of the following sizes complete with cast iron hand level companion flanges, bolts, nuts, washers & inserted rubber gaskets, as required and as per enclosed specification, with single phase Electrical Actuator, of 15Nm- 400Nm Torque, made of aluminium alloy (resistant to heat, acid , alkali, corrosion), and weather proof heavy duty motor, with stabilized start speed to effectively avoid water hammering, with waterproofing seal (IP 67) for all housing seals, low noise level, built –in thermal protection complete as per specifications

40 mm nominal bore

50 mm nominal bore

Providing and fixing lever operated gun metal ball valve with SS-316 ball.

40 mm nominal bore

50 mm nominal bore

Supplying, fixing, testing and commissioning of Cast Iron butterfly valve of PN 1.0 rating with SS-316 seat, Shaft SS-316 duly ISI marked complete with SS bolts & nuts, washers, gaskets conforming to IS 13095 of following sizes as required and two matching flanges as per table 'E' etc.

65 mm nominal bore

80 mm nominal bore

100 mm nominal bore

Providing, Installation ,testing and commission of Cast Iron Dual plate (SS-316 Plates) Non Return valve as per technical specification complete with rubber gaskets, SS bolts & nuts, washers etc. as required and two matching flanges as per table 'E' etc.

40 mm nominal bore

50 mm nominal bore

65 mm nominal bore

80 mm nominal bore

Providing and fixing of Cast Iron flanged Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 316, sheet with 3 mm dia. holes with stainless steel flange with rubber gaskets, SS bolts & nuts, washers etc. complete as required.

50 mm nominal bore

65 mm nominal bore

Providing and fixing of Pressure gauge (dial size minimum 6”) weather proof (IP-55) with a scale range from 0 to 10 Kg / cm² including stop cock.

Providing and fixing G.I. suction & delivery headers / pipes for water supply pumps (IS:1239 heavy class) with G.I. Fittings (bends, tees, reducers, plugs, union, flange & blank flanges etc.) and clamps and jointing with Teflon tape or hold tite including chase cutting and making good the walls, floors etc. wherever required. Painting with two or more coats of synthetic enamel paint of approved quality and shade over a coat of approved primer coat as directed including surface preparation (Shade as per pipe colour code)

40 mm nominal bore

50 mm nominal bore

65 mm nominal bore

80 mm nominal bore

Providing and fixing double flanged flexicion rubber expansion joint with unit control of standard length of a as per manufacturer specs tested to a pressure of 15 kg/sqcm including rubber gasket, flanges, nuts ,bolts and washers complete as required.40 mm nominal bore

Design, manufacture, supplying, fixing in position, testing and commissioning of the following front operated cubicle type, front access 2mm thick mild steel sheet, free standing, dust proof, switchboard with IP42 protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs, bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hz system and suitable for a fault level of 25 MVA symmetrical at 415 volts.

All switchboards shall have provision for entry of cables from the top or bottom as required.

All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The busbars insulation shall be with heat shrinkable sleeves. SMC/DMC shrouds and busbar supports shall be used. Padlocking facility shall be provided on all outgoing feeders doors and switch handles shall be lockable in OFF position.

Electric Panel For Water Supply Pumps at Water Supply Pump Room

INCOMING

1 No. 63 amps TPN MCCB with the following accessories:

1 No. square flush mounting 0-500 volts scaled voltmeter with three way and OFF switch.

Three phase indicating lights.

Electrolytic high conductivity three phase and neutral tinned copper bus bar rated at 100 amps having a current density of 1 amp per Sqmm suitable to with stand symmetrical fault level of 25 MVA at 415 volts. The neutral bus bar is to be of 100% capacity.

OUTGOING UNITS

6 25/40 Amp. TP + NL M.C.C.B. with rotary handle of breaking capacity 25KA

Two 63 Amp. TP + NL M.C.C.B. with rotary handle of breaking capacity 25KA

2 Nos. fully automatic DOL starters with push buttons and ON/OFF indicating lights and overload relays for 1.5 to 7.5 HP pump .

2 Nos.cyclic relay for automatic duty changeover of pumps.

2 No. single phase preventors.

Space for 3 Nos. Level Controllers.

Switchgear shall be suitable for the HPS of various motors.

1 Nos. 63 Amp. TPN MCB Spare.

2 Nos. 32/40 Amp. TPN MCB Spare.

The motor control panel shall be prewired with colour coded wires with identification labels complete in all respects as required.

Supplying, installing, testing and commissioning controllers with low voltage relays, stainless steel probes and PVC shroud wiring from tank top to probes of required.

Level Controller For Water Supply Pump:

To start pump when water level is low in Domestic Water U.G. tank and shut off pump when Domestic Water U.G. tank is full. Also to stop when water level is low in raw water underground tank.

SEWAGE TREATMENT PLANT 45 KLD

Design, Supplying, installing, testing & commissioning of Sewage Treatment Plant of 45 KLD (excluding excavation, back filling & disposal of surplus earth MS / Civil construction work) for the following duty:

Sewage treatment plant shall include the following items:

a. Screen chambers with SS Screen b. Equalization Tank c. Aerobic & Anoxic tank d. MBBR TANK e. Air Blowers f. MBBR Media g. Recirculation pumps, backpulse pump, permeate pump etc. h. Dewatering system j. Electrical Panel, Cabling (Power & Control), Earthing k. Tertiary Treatment l. Clear Water tank and Flushing Water tank.

BOD5 : 250 - 350 mg/lit

Total Suspended Solids (TSS) : 250 - 450 mg/lit

COD : 500 - 700 mg/lit

Oil / Grease : upto 50 mg/lit

Inflow time : 24 HRS

Peak factor : 3

Temperature : Ambient

Desired Sewage Quality After Treatment

BOD5 : < 10 mg/lit

Total Suspended Solids (TSS) : < 10 mg/lit

COD : < 50 mg/lit

Oil / Grease : < 5 mg/lit

Colour : Colourless

Odor : unobjectionable

E.coli : Nil

NH4-N :< 5 mg/lit

N Total :< 10 mg/lit

PO4-P : 2 mg/lit

Vendor shall ensure submission of detailed GA drawings (Plan & Section), P&I diagram, schematic diagram for the above said component and additional component if so required for the complete working of the STP for the full capacity.

INLET SEWAGE CHARACTERSTICS (ASSUMED)

EFFUENT TREATMENT PLANT 5KLD

Design, Supplying, installing, testing & commissioning of Effluent Treatment Plant of 5 KLD (excluding excavation, back filling & disposal of surplus earth and Civil construction work) for the following duty:

Effluent from OT Scrubs, blood bank, labs etc. Some solvent/ chemical waste originating typically from hospital complex shall also be discharged into the ETP. Design to take consideration of same.

INLET EFFLUENT CHARACTERSTICS

BOD : 250 - 600 mg/l

S. Solids : 200 - 650 Mg/l

COD : 600 - 1200 mg/l

Oil & Grease : 50-140 mg/L

Effluent discharge standard after treatment

BOD - Less than 150 Mg/L

S. Solids - Less than or equal to 100 Mg/L

COD - Less than or equal to 300 Mg/L

Oil & Grease - Less than 5 Mg/L

Screen Chamber

Equalization tank/sump

Primary Tube Settler

Dosing System

Sludge Holding Tank

UV System

Air Blowers, Pumps & equipment

Piping, valves etc

Clarified Water tank

Electrical Panel & Cabling

Contractor shall ensure submission of detailed GA drawings (Plan & Section), P&I diagram, schematic diagram for the above said component and additional component if so required for the complete working of the STP for the full capacity.

Effluent treatment plant shall include the following items:

ELECTRICAL WORK

Wiring for light point/ fan point / exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular switch, modular plate, suitable GI box etc as required.

Group C

Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, 2 way modular switch, modular plate, suitable GI box etc as required.

Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit alongwith 2 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit / submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required

CIRCUIT / SUBMAIN WIRING

2x1.5 sq mm + 1x1.5 sq mm earth wire

2x2.5 sq mm + 1x2.5 sq mm earth wire

2x6 sq mm + 1x6 sq mm earth wire.

2x10 sq mm + 1x6 sq mm earth wire.

2x16 sq mm + 1x6 sq mm earth wire.

4x2.5 sq mm + 2x2.5 sq mm earth wire

4x6 sq mm + 2x6 sq mm earth wire.

4x10 sq mm + 2x6 sq mm earth wire.

4x16 sq mm + 2x6 sq mm earth wire.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of PVC conduit along with the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

20mm dia

25mm dia

32mm dia

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 amps one way switch

15/16 amp one way switch

5/6 amp 3 pin socket outlet

5/16 amp 6 pin socket outlet

TV anteena Socket Outlet

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.

1 or 2 Module (78mm x 78mm x 45mm) - For Telephone & TV outlet.

4/5 Module (78mm x140mm x 50mm)

6 Module (78mmX205mmx50mm)

8/9 Module (78mmX230mmx60mm)

12 Module (135mmX205mmx60mm)

Supplying and fixing 2 pin 5 Amp Ceiling rose on the existing junction box/ wooden block including connection etc as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Supplying and fixing Ding dong sound call bell single phase, 230 volts, complete as required.

Installation, testing and commissioning of pre wired fluorescent fitting / Compact fluorescent fitting off all type complete with all accessories and tube etc directly / wall including connection with 1.5 sq.mm FR PVC insulatted. copper conductor single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable, etc. as required.

Installation of exhaust fan up 450 mm sweep in the existing opening including making the hole to suit the size of above the fan, making good the damage, connection, testing, commissioning etc. as required.

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings). (For UPS Supply)

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

20mm dia

25mm dia

Supply & drawing following sizes of FR PVC insulated copper conductor single core cables in existing surface/recessed steel / PVC conduit including dismantling as required.

2 x 1.5 sq.mm

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

8 Way Double Door

12 Way Double Door

Supplying and fixing following ways, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

6 Way (4+18), Double Door Horizontal Type

8 Way (4+24), Double Door Horizontal Type

Supplying and fixing following ways surface / recess mounting Vertical type 415 Volts TPN MCB distribution board, of sheet steel dust protected duly power painted inclusive of 200 Amps tinned copper bus bar common, neutral link, earth bar, din bar, for mounting MCB's (But without MCB's and incomer) as required. ( Note:- Vertical Type MCB TP DB is normally used where 3phase outlets are required.

8 Way (4+18), Double Door Vertical Type

12 Way (4+24), Double Door Vertical Type

Supplying and fixing 6 Amp to 32 Amp rating 240 volts, 10 KA "C" Curve Miniature Circuit Breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc.,as required.

6 / 32 Amp Single Pole

40 Amp DP

50/63 Amp DP

6/32 Amp TPN

40 Amp TPN

50/63 Amp TPN

Supplying and fixing Single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing of following rating double pole ( Single pole & neutral), 240 volts, resudual current circuit breaker (RCCB), having a sensivity current 30 miliampere in the existing MCB DB complete with connections, testing & commissioning etc as required.

Providing and fixing M.V. danger Notice plate of 200mm x 150 mm of made of mild steel, at least 2 mm thick and vitreous enamelded white on both side and with inscription in single red colour in front side as requird

Providing and fixing H.T. danger Notice plate of 250mm x 200 mm of made of mild steel, at least 2 mm thick and vitreous enamelded white on both side and with inscription in single red colour in front side as requird

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) as required.

Providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Providing and fixing earth bus of 50 mm x 5 mm copper strip on surface for connections etc. as required.

Providing and fixing 50 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.2Xrate

Providing and fixing of lighting conductor finial made of 25 mm dia 300 mm long, GI tube having single prong at top with 85 mm dia 6mm thick G.I Base plate including hole etc. as required

Providing and fixing GI Tape 20mmx 3mm thick on parapet or surface of wall for lighting conductor complete as required. (for Horizental Run)

Providing and fixing GI Tape 20mmx 3mm thick on parapet or surface of wall for lighting conductor complete as required. (for Vertical Run)

Providing and fixing testing Jointing made of 20mmx 3mm thick G.I Strip 125 mm Long. With 4 nos of G.I bolts. Nuts chuck nuts and spring washers etc. as required

Providing and Laying G.I tape 32mm x 6mm from earth electrode directoly in ground as required.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

120 mm dia (OD-120 mm & ID-103 mm nominal)

200 mm dia (OD-200 mm & ID-175 mm nominal)

INSPECTION CHAMBER:

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design :

Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets.

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

1 run of cable

2 run of cable

3 run of cable

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.

Upto 35 sq. mm (clamped with cable tie)

Above 35 sq. mm and upto 95 sq. mm (clamped with cable tie)

Above 95 sq. mm and upto 185 sq. mm (clamped with cable tie)

Above 185 sq. mm and upto 400 sq. mm (clamped with cable tie)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

2 x 6 sq. mm (19mm)

2 X 10 sq. mm (19mm)

2 X 16 sq. mm (22mm)

3½ X 35 sq. mm (32mm)

3½ X 50 sq. mm (35mm)

3½ X 70 sq. mm (38mm)

3½ X 95 sq. mm (45mm)

3½ X 120 sq. mm (50mm)

3½ X 150 sq. mm (50mm)

3½ X 185 sq. mm (57mm)

3½ X 240 sq. mm (62mm)

3½ X 300 sq. mm (70mm)

4 X 10 sq. mm (25mm) including 4x6 sq.mm

4 X 16 sq. mm (28mm)

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

100 mm wide x 50 mm depth x 1.6 mm thickness.

150 mm wide x 50 mm depth x 1.6 mm thickness.

300 mm wide x 50 mm depth x 1.6 mm thickness.

450 mm wide x 50 mm depth x 2.0 mm thickness.

600 mm width X 50 mm depth X 2.0 mm thickness

750 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

100 mm wide x 50 mm depth x 1.6 mm thickness.

150 mm wide x 50 mm depth x 1.6 mm thickness.

300 mm wide x 50 mm depth x 1.6 mm thickness.

450 mm wide x 50 mm depth x 2.0 mm thickness.

600 mm width X 50 mm depth X 2.0 mm thickness

750 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

100 mm wide x 50 mm depth x 1.6 mm thickness.

150 mm wide x 50 mm depth x 1.6 mm thickness.

300 mm wide x 50 mm depth x 1.6 mm thickness.

450 mm wide x 50 mm depth x 2.0 mm thickness.

600 mm width X 50 mm depth X 2.0 mm thickness

750 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member"(galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required.

100 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

750 mm width X 62.5 mm depth X 2 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Reducer” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

100 mm wide x 50 mm depth x 1.6 mm thickness.

150 mm wide x 50 mm depth x 1.6 mm thickness.

300 mm wide x 50 mm depth x 1.6 mm thickness.

450 mm wide x 50 mm depth x 2.0 mm thickness.

600 mm width X 50 mm depth X 2.0 mm thickness

750 mm width X 62.5 mm depth X 2 mm thickness

Supplying, installation, testing & commisioning of following capacity Plug In/ tap off box on the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick sheet steel enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete etc. as required

125 A 15kA SC for 1 sec (including 100A)

200 A 25kA SC for 1 sec

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes cubicle panel, making connections, etc. as required.

100 A, 25 KA,TPMCCB

200 A, 25 KA,TP MCCB

MAIN L.T. PANEL

INCOMERS from 1 Nos. 315 KVA Transformers

1 nos. 630 AMP. Four Pole, Electrically operated 3 position motorized (220 V AC) drawout type Air Circuit Breaker with all inbuilt protections, with microprocessor based release, over current, earth fault, short circuit, Instantaneous short circuit, closing coil (220 V AC), trip coil (24 V DC), shunt trip release, inbuilt U/V release with LCD / LED display for event history & measurement of current parameters, 50 KA Breaking Capaciy with all standard accessories i.e. auxillary switch with 4NO + 4NC contacts, cradle, handle, safety shutter in confirmity with IS:60947

Protection releases / relays, Metering & Accessories for each Transformer incomers

Over Voltage / Under Voltage relay / release (3 phase) with timer.

Master trip relay.

Trip Circuit Supervison relay.

TNC switch.

1 set of 3 CT's of ratio 600/5A, Class 1.0 accuracy 15 VA burden for metering.

1 set of 3 CT's of ratio 600/5A, Class 1.0 accuracy 15 VA burden for APFCR.

1 set of 4 CT's of ratio 600/1A, Class PS for protection.

1 no. CT's of ratio 600/5A, Class 5P10 for protection.

Energy analyser (digital type) consisting of I, V, KW, KWH, KVA, PF, HZ, MDI (EM 6400 of Conzerve or equi.) with RS 485 communication port for communication / report generation. (or Dual meter)

Power factor meter.

Frequency meter.

3 Nos. LED type phase indicating lamps, each lamp shall be with bakup MCB along with hooter, auxillary relay, 2 sets of push buttons.

5 Nos. LED type indicating lamp for indicating the status of feeder - ON / OFF / TRIP / Trip circuit healthy / DC supply healthy. Each lamp shall be with bakup MCB.

BUSBARS

800 Amp TPN busbars of aluminium alloy as per SLD.

OUTGOING

01 Nos 315A FP MCCB (25KA)

01 Nos 200A TP MCCB (25KA)

03 Nos 100A TP MCCB (25 KA)

04 Nos 63A TP MCCB (25 KA)

06 No 63A FP RCCB (300 mA)

Main L.T. Panel Described as Above.

AUTOMATIC POWER FACTOR CORRECTION PANEL (CAPACITOR PANEL)

Design, Manufacturing, Supply, Receiving, Unloading, Shifting, testing & commissioning of 14 SWG CRCA sheet steel fabricated cubical type 100 KVAR A P F C Panel consisting of 5 /10 / 25 / KVAR (at 415 Volts rated voltage of bank shall be 440 Volts) capacitor units in tier formation, housed in an integrated cubicle type automatic switching ON and OFF control panel, floor mounting, dust & vermin proof, front operated construction, enclosure class - IP 42, powder coated after proper treatment with 9 tank process with top/bottom removable gland plates, as required, double compression type cable glands, earth bus, hinged and lockable doors to achieve dust and vermin proof complete with all inter connections small wiring by min. 2.5 sq. mm. copper wires, ckt labels etc. The Aluminium Bus Bar shall be of suitable length, 500 volts, 3 phase 50 Hz TPN, electrolytic aluminium as per IS 8623 .

All out going MCCB's shall be thermal-magnetic based with inbuilt O/L & S/C release.

AC3 duty contactors should be used for switching individual capacitor banks.

The fault withstanding capacity of panel & its control gear shall be min. 50 KA rms for 1 sec.

Each section of capacitor panel shall have Verticle hood & exhaust fans for ventilation purpose.

INCOMING

Incomer circuit breaker has been included in the main panel.

1 set- 3 CTs , ratio 200 / 5A Class 1.0 accuracy 15 VA burden for metering.

Micro processor based automatic power factor control relay (3 phase) (including power factor meter) in 13 steps for automatic cut off or add on capacitor units to keep the power factor at 0.95 with variation of loads. All associated auxiliary contactors / relays shall be provided with in the scope of work.

Phase indicating lamps with HRC fuses, and indicating in each capacitor chamber unit to indicate On/Off status of capacitor unit.

BUS BARS

200 AMP, 500 Volts, 3 phase 50 HZ TPN high conductivity electrolytic Aluminium bus bar of suitable length, SMC / DMC supports, with colour coding and insulated by heat shrinkable sleeves and clips on shrouds for joints.

OUTGOINGS

3 nos. of 63 AMPS TPN MCB (25 KA) and 80 amps AC3 duty contactor with 25 KVAR, MPP resin filled, super heavy duty ,440 V capacitor bank, start stop push button for manual operation including on/off indicating lamps and delay timer complete.

2 nos. of 32 AMPS TPN MCB (10 KA) and 40 amps AC3 duty contactor with 10 KVAR, MPP resin filled, super heavy duty ,440 V capacitor bank, start stop push button for manual operation including on/off indicating lamps and delay timer complete.

1 no. of 16 AMPS TPN MCB (10 KA) and 20 amps AC3 duty contactor with 5 KVAR, MPP resin filled, super heavy duty ,440 V capacitor bank, start stop push button for manual operation including on/off indicating lamps and delay timer complete.

Capacitor Panel as described above

DG PANEL

INCOMERS from main LT Panel

1 Nos. 315A MCCB with 315 A 4P Contractor

Protection releases / relays, Metering & Accessories for each Transformer incomers

1 set - 3 CTs of ratio : 300/5A , Class 1.0 accuracy 15 VA each burden for metering.

Energy analyser (digital type) consisting of I, V, KW, KWH, KVA, PF, HZ, MDI (EM 6400 of Conzerve or equi.) with RS 485 communication port for communication / report generation. (or Dual meter)

3 Nos. LED type phase indicating lamps, each lamp shall be with bakup HRC fuse/MCB along with hooter, auxillary relay, 2 sets of push buttons.

INCOMERS from 1Nos. 160 KVA D G sets

1 Nos. 315A MCCB with 315 A 4P Contractor

Protection releases / relays, Metering & Accessories for each D G set incomers

Over Voltage / Under Voltage relay / release (3 phase) with timer.

Reverse power relay.

1 set - 3 CTs of ratio : 300/5A , Class 1.0 accuracy 15 VA each burden for metering.

1 set - 3 CTs of ratio : 300/5A , Class 5P20 accuracy 20 VA each burden for protection.

Energy analyser (digital type) consisting of I, V, KW, KWH, KVA, PF, HZ, MDI (EM 6400 of Conzerve or equi.) with RS 485 communication port for communication / report generation. (or Dual meter)

3 Nos. LED type phase indicating lamps, each lamp shall be with bakup HRC fuse/MCB along with hooter, auxillary relay, 2 sets of push buttons.

5 Nos. LED type indicating lamp for indicating the status of feeder - ON / OFF / TRIP / Trip circuit healthy / DC supply healthy. Each lamp shall be with bakup HRC fuse/MCB.

Shut down due to low lube oil pressure/High water temp/Over speed/Low fuel level - set of 4 indication lamps.

D G control incorporating engine start / stop indicating three attempt facility and on failure to start, engine lock out.

1 nos battery charger with DC voltmeter and ammeter suitable for the DG sets (160 KVA)

Note : In normal case all three lamps shall be ON to indicate that incoming power supply is available. In case of power resumption after failure buzzer shall ring to indicate the power supply is resumed. There shall be one push button to acknowledge the same.

The ACB shall be electrically interlocked with the bus coupler and Transformer incomers.

BUSBARS

500 Amp TPN busbars of aluminium alloy as per SLD.

OUTGOING

01 Nos 315A TP MCCB (25KA)

03 Nos 200A TP MCCB (25KA)

02 Nos 100A TP MCCB (25 KA)

04 Nos 63A TP MCCB (25 KA)

03 Nos 40A TP MCCB (25 KA)

03 Nos 63A FP RCCB (300 mA)

Main L.T. Panel Described as Above.

DISTRIBUTION PANEL

L+P PANEL ( GROUND & FIRST)

INCOMING

1 No. 200 Amp FP MCCB (25 KA)

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUSBAR

300 Amp FP aluminium busbar with coloured heat shrinkable sleeve.

OUTGOING

12 Nos. 25 Amp FP MCB (10 KA)

4 Nos. 40 Amp FP MCB (10 KA)

12 Nos. 63 Amp FP MCB (10 KA)

Panel described as above

UPS PANEL ( GROUND FLOOR )

INCOMING

2 No. 200 Amp FP MCCB (35 KA)

2 Set of phase indicating lamps with Single Pole MCB.

2 Set of ON / OFF indicating lamps with Single Pole MCB.

BUSBAR

300 Amp TPN copper busbar with coloured heat shrinkable sleeve.

OUTGOING

1 Nos. 100Amp FP MCCB (25 KA).

4 Nos. 63Amp FP MCB (10 KA).

10 Nos. 40Amp FP MCB (10 KA).

10 Nos. 40Amp DP MCB (10 KA).

6 Nos. 63Amp DP MCB (10 KA).

Panel described as above

EXTERNAL LIGHTING PANEL (OUTDOOR TYPE)

INCOMING

1 No 100 Amp FP Moulded Case Circuit Breaker (35 KA) with 100 Amp 4 Pole Contactor & Timer.

1 Set of phase indicating lamps.

1 Set of ON/OFF indicating lamps with SP MCB.

BUS BARS

200 Amp FP aluminium busbar with coloured heat shrinkable sleeve.

OUTGOING

08 Nos. 25 Amp DP MCB (10 KA)

03 Nos. 40 Amp DP MCB (10 KA)

Panel described as above

Supply of XLPE insulated PVC sheathed, heavy duty, armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts. (conforming to IS-7098. (Part-I).

3.5 core, 300 sq.mm.

3.5 core, 240 sq.mm.

3.5 core, 185 sq.mm.

3.5 core, 150 sq.mm.

3.5 core, 120 sq.mm.

3.5 core, 95 sq.mm.

3.5 core, 70 sq.mm.

3.5 core, 50 sq.mm.

3.5 core, 35 sq.mm.

4 core, 16 sq.mm.

4 core, 10 sq.mm.

4 core, 6 sq.mm.

2 core, 16 sq.mm.

2 core, 10 sq.mm.

2 core, 6 sq.mm.

Supply & Laying of following sizes of 1.1KV grade multistranded copper conductor PVC insulated cable including termination complete as required in existing cable tray.

1C x 50 sq.mm PVC Insulated cu wire including termination etc.

1C x 16 sq.mm PVC Insulated cu wire including termination etc.

Supply, erection, testing and commissioning of following sizes of TV splitter of aluminium die cast body in suitable size of G.I. Box.

Supply, erection, testing and commissioning of following co-axial cable in existing conduit.

Supply & installation of 32 Amp 3 phase, 415 volt, 50 Hz water tight (IP-55) socket outlet with interlocking switch complete with all fixing accessories.

Supply & installation of 32 Amp single phase 240 Volt, 50 Hz, water tight (IP-55) socket outlet with interlocking switch complete with all the fixing accessories as below.

Supply & fixing of following size (GP RACEWAY- Fabricated from GP Sheet) race ways for electrical & LV wiring including neoprene gasket in joints, cutting the floor & jaming the race way / hanging in ceiling, supporting arrangement as approved by consultant / architect with all necssary hard ware (including civil work) as per site requirement. The thickness of raceway & cover shall be as per technical specification.

100 mm wide x 40 mm deep.

200 mm wide x 40 mm deep.

Supply & fixing of following size of Raceway Junction Box made out of GP Sheet for electrical & LV wiring including, cutting the floor & jaming the junction box / hanging in ceiling, supporting arrangement as approved by consultant / architect with all necssary hard ware (including civil work).(Junction box to be provided as per drawing/ as per site requirement & as per specification). The thickness of junction box shall be a as per thechnical specification.

150 mm wide x 50 mm deep.

250 mm wide x 50 mm deep.

Supply, Installation, Testing & Commissioning of Earthing Junction Box size - 400mm x 300mm x 80mm made out of 16 SWG CRCA sheet with seven tank process & powder coating, earthing link (32mm x 6mm copper strip) front door with glass as complete as required.

FIRE ALARM SYSTEM (ADDRESSABLE TYPE) AND PA SYSTEM

Two Loop Panel.

Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector acclimate type sensetive level (0.524%) OVS/ft. complete with mounting base complete as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. (75 DBA @3 mtr. & 75CD flashing)

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supply, installation, testing and commissioning of addressable monitor module complete as per specification.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 480 Watt, supply complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required.

Speaker cable Single pair, 2-core, 1.5 sqmm

SUPPLY & INSTALLATION OF LIGHT FIXTURES & FANS

SITC of following rating recess / surface mounted LED round / square shape down light luminarie with pressure die cast housing for single phase supply voltage Luminarie shall be confirm to IS: 10322 part -5 / section -2 or IEC :62722 withh all neccesary accessories as required. Make:- Havells/Philips/Crompton/Wipro / India Bulls.

12W LED Round Down Light (Recess )

15 / 16 W LED Round Down Light (Recess )

18 /20 W LED Round Down Light (Surface)

18 /20 W LED Round Down Light (Recess)

2' x 2' LED Panel Light (Recess)

Bulk Head fitting with 9/10Watt LED.

S.I.T.C of following rating surface mounted LED Tube Lighting Fitting Suitable for 230V 50 Hz, Single Phase Supply etc. complete as required.

10/12 W LED Tube Light

20/22 W LED Tube Light

30 W COB based round LED Light with multiple beam angles (36 Degree)

SITC of 300 mm (12") Exhaust fan (Metal body) suitable for single phase 230 volts, 50 Hz., AC supply complete with motor, louvers/shutters etc. complete as required. Make :- Usha/Crompton / Havells .

Supply Installation, Testing & Commissioning of following sizes ceiling fan 3 Blades confirming to IS:374:2019 including wiring the down rods of standard (up to 30cm) with 1.5 sq.mm FR PVC insulated copper wire suitable for 230V 50 Hz, Single phase supply etc. complete as required. Make :- Usha/Crompton / Havells .

1200 mm ( 48") BLDC 5 Star rating 32W Ceiling Fan

UPS SYSTEM

Supply, fitting, fixing, testing and installation of 40 KVA, ON Line UPS three phase input and three phase out put power system of in put voltage range 360V/380/V/400V/485V AC , Frequency range 40 HZ to 60 Hz, +/- 10% and out put voltage range 415V +/-1%, AC frequency range, 50Hz, +/-1% poower factor 0,8/3.1, Harmonic distrortion -< 2% THD (Linear Load): 5% THD (Non- Liniear Load) along with required Batteries, Battery Stand, UPS Box Battery Lead etc as required.

UPS shall carry design output at 40 deg.

Shall have soft start and hold of for incoming supply.

Invertor capability to supply 150% load for 5 sec.

SNMP card, compatible for BMS connectivity on backnet/MODBUS, Inbuilt Isolation transforme.

Shall not allow deep discharge of the battery and shall not go to 10.5 volts in case of 12 volt cells.

Battery shall be external type with rack and suitable for 30 minute backup on 100% load.

Suitable size of copper cable between UPS and battery bank shall be provided

UPS shall be compatible for 3 nos unit in parallel operation. (Synchronize). Parallel operation kit shall be supplied with UPS.

SITC of MS Battery Rack suitable for 40 to 50 UPS Battery Installation.

SITC of 60 nos. 65 AH Flat type Sealed Maitanace Free (SMF) Battery with 24 months replacement warranty. IS:1652:1991. (VAH Required minimum 46800 for 40 KVA UPS (65AH x 60 Nos. x 12V = 46800 VAH)

Total cost of 1 Set 50 KVA UPS, Batteries & Accessories (A+B+C)

DATA, TELEPHONE SYSTEM INCLUDING ACTIVE COMPONENTS

Supply, Installation, Testing & Commissioning of Cat 6, 24 Port Patch Panel

Supply, Installation, Testing and Comissioning of Cat 6 patch cord 3 feet for rack and user end termination - 1Mtr

Supply, Installation, Testing and Comissioning of Cat 6 patch cord 7 feet for rack and user end termination - 2Mtr

Supply, Installation, Testing, Commissioning of Cat 6, Information Outlet (I/O) including G.I. Box and modular cover plate.

Supply, Installation, Testing and Comissioning of 24U floor mounted Rack with accessories.

Supply, Installation, Testing & Commissioning of 24 port 10/100/1000Mbps, 4SFP module, L-2 Switch, POE.

Supply, Installation, Testing & Commissioning of EPABX SYSTEM Configuration as Below:- Analog Trunk Line 6 Nos. Digital Line 2 Nos Analog Extensions 60 Nos.

Supply, Installation, Testing & Commissioning of Digital Phone for Operator Console

Supply, Installation, Testing & Commissioning of Type Analog Phone with speaker phone, .

Supply, Installation, Testing & Commissioning of 6 Core OM4 Multimode Fiber Cable.

IP CCTV SYSTEM

Supplying, installation, testing & commissioning of 1080p HD Indoor IP Dome camera with1/3-inch CMOS, Sensor pixels 1920 x 1080, Sensitivity-0.04 lx (color) , Dynamic range 75 dB Wide Dynamic Range (WDR), True day/night, Automatic Electronic Shutter, Video compression H.264 ; M-JPEG, White balance, BLC, H.264 quad-streaming, Motion/tamper/audio detection, Privacy Mask, Lens 3.6 mm lens, 3-axis adjustment (pan/tilt/ rotation), ONVIF Profile S, CE Certified.

Supplying, installation, testing & commissioning of 5MP 30 fps HD indoor / outdoor IR IP bullet camera with 1/3‑inch CMOS, Sensor pixels 2612 (H) x 1980(V), Sensitivity-0.24 lx (color) 0.04 lx (mono) ,IR range 30 mtrs, Dynamic range 70 db, True day/night, Automatic Electronic Shutter, Video compression H.264 MP ; M-JPEG, White balance, BLC, Analog video output, Lens (zoom / focus) 3.6 mm lens, Two-way, full duplex Audio, Audio compression AAC, G.711, L16 , ONVIF Profile S, CE Certified.

Supply installation and commission of pann tilt zoom camera with 360 deg pan and 90 deg tilt with 36 X Zoom having maximum resolution of Max. 1920 × 1080 @30fps,true day night camera with 130 m IR range , optional, fine picture at Ultra-low light,supports compression format H.265, H.265+, H.264+, H.264, 3D Digital Noise Reduction support.

SITC of IP network recoder with following feature Processor - Dual-core embedded processor . Two-way Talk - 1 channel Input, 1 channel Output, RCA,Video Output - 1 HDMI, 1 VGA , IP Camera Input - 8/16/32 Channel IP , Compression - H.264+/H.264/MJPEG,Video Resolution - 2560 × 1920, 2048 × 1536, 1920 x 1080, 1280 x 1024, 1280 x 720, 1024 x 768 , Hard Disk - 4 SATA Ports, up to 8TB ,Motion Detection - MD Zones: 396 (22 × 18),Recording Mode - Manual, Schedule (Regular, Continuous), MD (Video detection: Motion Detection, Camera Blank, Video Loss), Alarm, Stop, Backup Mode - USB Device /Network , Interface Ports - 1 HDMI, 1 VGA, 2 USB(1 USB 2.0 , 1 USB 3.0 ), 1 RS485, 1 RS232, 1 RJ45.

Supply, Installation, Testing and commissioning of Managable 24 port Switch with Power on Ethernet (PoE) enabled, 10/100, RJ45 Access ports with PoE complete as required.

Supply, installation, testing and commissioning of of 6 TB HDD all accessories complete as required.

Supply installation and commissioning of 48 inch LED monitor for disply of camera.

SOLAR PHOTO VOLTAIC POWER GENERATION SYSTEM

Supplying installation testing and commissioning of Grid interactive roof top solar photo voltaic power generation system including all the required accessories like Solar PV module, Grid Tie invertor, arrey junction box, cabling & wiring, earthing, surge protection device, FRLSame structure for mounting of solar panel. The cell shall be poly crystaline silicon cells of 6 inch each and module efficiency shall be more than 17%. Solar module shall have linear output warranty with degradation not exceeding 0.7% FRLSom 2nd Year onwards. Minimum 80% power output must be assured at end of 25 years. The FRLSont glass of solar module shall be low iron tempered glass ARC type. Termination box shall be Thermo-plastic, IP 67 or better, UV resistant with built-in-bypass. The nominal power of a single PV module shall be minimum 325 Wp or higher. Positive power tolerance modules only to be used. RF identification tag for each solar module shall be provided inside the module and must be able to withstand environmental conditions. The solar panel shall be complience of IEC 61215, IEC 61730 certified by TUV Rheinland / UL. The solar panel shall be installed as per BOQ & detailed technical specification.

AUTOMATIC FIRE DETECTION GAS SUPPRESSION SYSTEM IN PANELS

Supply, fixing, testing and commissioning of Automatic Linear pneumatic Tube Detection based Novec 1230 System for Electrical Panels (consisting of the following components.

6 KG Novec 1230, DLP Assembly with automatic valve mounted on approved cylinder, push in connector for tube, Novec 1230 gas, mounting bracket, End of Line adopter and low pressure switch for monitoring system activation.

Linear pneumatic heat Detection Tube with all necessary fittings & supports

Master Control Unit with Audio Visual Alarm with wiring to make complete system operational. The Control Panel should have provision for integration with Fire Alarm/SCADA/BMS System (Supply to be provide by the end client at 220 Volt AC).

DG SET & SUBSTATION WORK

DIESEL GENERATING SET

Supply, Installation testing and Commissioning of Silent type Diesel Generating Set with AMF PANEL at 0.8 PF, 415 Volts, 50 cycles per second, 1500 rpm, 3 phase, suitable for parallel operation / PLC based synchronization, 0.85 load factor including circuit breaker for isolation, sound proof acoustic and weather proof enclosure, residential type silencer (as per CPCB norms-2) fabricated out of CRCA sheet of 16 SWG thickness with 9 tank pretreated before powder coating with ventillation system complete in all respects comprising of the following.

Diesel Engine -

Diesel Engine suitable for driving alternator of above rating, compression ignition, 4 stroke cycle, Radiator cooled, turbo charged, battery starting, 1500 RPM, suitable for above output of alternator at 40oC, 50% RH & at 210 M MSL and confirming to BS 5514, BS 649, IS 10000, capable of taking 10% overloading for one hour after 12 hrs of prime continuous loading, complete with all the accessories i.e. tachometer with hour meter, flexible coupling with guard, crank case of steel, crank shaft, conncting rods, electronic governing system, dynamically balanced flywheel, air intake manifold, Air cleaner, anti vibration pads, starter motor, including all other accessories required to complete the system.

Instrument Panel - Engine mounted Instrument Panel fitted with and having digital display for followings :

Start stop switch with key

Water temperature indication

Lubrication oil pressure indication.

Lubrication oil temperature indication.

Battery charging indication

RPM indication

Over speed indication

Low Lube oil trip indication

Engine hours indication

Alternator -

Synchronous Alternator of above capacity at 0.8 PF, 3 phase, 415 volts, 50 cycles, 4 wire, 1500 RPM, suitable for operation at 40 deg C, 50% RH & at 210 meter above MSL, capable of taking 10% overlioading for one hour after 12 hrs of prime continuous loading, brushless, self excited, self regulated through AVR, continuous duty confirming to IS 4722, BS 2613 suitable for tropical conditions, class H insulation, including terminal box suitable for bus duct termination / cable termination as required.

Note : - Alternator should have with all other accessories as per specified in Technical specfications.

Base Frame - Both the engine and alternator shall be mounted on suitable base frame made of MS channel which shall be installed on cement concrete foundation and vibration isolating arrangement as per recommendations of manufacturer.

Inbuilt Fuel tank of standard capacity complete with inlet and outlet connections, oil indication gauge, drain plug, air breather, fuel transfer system for automatic fuel refilling system with pump, piping, valves, level indicators etc. complete.

Daily service Fuel tank of 990 liters capacity fabricated out of 2 mm thick MS sheet complete with inlet and outlet connections, oil indication gauge, drain plug, air breather, provision for fuel transfer system, level indicators and all standard accessories etc. as required.

Exhaust Silencer - Exhaust manifold with residential silencer.

The D G set should be supplied with required hardware for external PLC based auto synchronization, auto load sharing, auto load management system.

Starting system - 24 Volt DC starting system comprising of starter motors : voltage regulator and arrangement for initial excitation complete with 12/24 Volts suitable nos. lead acid type batteries of suitable AH.

Ventillation System - Arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air into the atmosphere as per standard specifications.

Supply, Fixing, testing and Commissioning of Exhaust gas piping system of Class `B' MS pipe as per IS:1239 for upto 150 mm dia and for 200 mm dia & above MS pipe as per IS:3589 with welded joints, cut to required lengths with necessary bends, fittings, flanges, painting over primer coat, with mineral wool / rock wool insulation of minimum 75 mm thick of 150 Kg per cu M density on all sides of exhaust pipe, with chicken mesh wrapping and 26 SWG aluminium sheet cladding complete as required. The aluminum foil should be tightly cladded to insulation surface of pipe. The aluminum cladding shall be locked with sheet metal screws with other sections of aluminium foil. The measurement shall be done on the basis of centre line. (Stack height should be in accordance with emission regulations of CPCB, which will go well above the top most terrace) The exhaust piping system should be suitable for upto 550oC temperature, the surface temperature of exhaust pipe shall not exceed more than 60oC. (The rates are exclusive of support structure) (Note - Final size of exhaust pipe will be confirmed by the DG vendor after calculating the actual back pressure and submit the same to client / consultant for approval)

100 mm dia (wall thickness - 4.85 mm)

Supply & fixing of SS Bellow of following diameter

100 mm dia

Supply & fabrication of D G exhaust pipe supports by M.S angle iron of size not less than 100 x 50 mm x 6/8 mm duly grouted in the wall through minimum 8 mm thick plate and with suitable MS angle / channel iron structure. The entire MS support structure should be painted by 2 coats of anti corrosive paint over primer coat of approved shade and make. The design of support to be duly approved by the Structural Consultant / Architect before fabrication and installation.

11 KV HT VCB FOUR BREAKER PANEL BOARD (INDOOR TYPE)

Supplying, Installation, Testing & Commissioning of indoor type floor mounted metal clad, 11 KV VCB panel with 3 nos VCBs, totally inclosed & fully interlocked, horizontal drawout, horizontal isolation type breaker as per IS 13118, as amended up to date and additional specifications, having capacities as mentioned below, single break, trip free mechanism, manually charged and manually closing breaker suitable for use on 11 KV, 3 phase, 50 Hz A.C. supply with short circuit fault level of 350 MVA, complete with self contained, fully interlocked, rack in and rack out mechanism, air insulated but encapsulated copper bus bars of 630 Amp capacity, breaker featured with mechanical ON/OFF indicator with hand trip device.

Spring release coil, shunt trip coil and auxiliary switch of 4 NO + 4 NC and equipped with following switchgears and accessories i/c connections for 3C x 300 sq.mm. XLPE 11 KV cable (cable entry from bottom), end termination with heat shrinkable jointing material etc. as required. (Note - Cost of end termination not included in this item).

a) 1 No, 630 Amp, VCB.

d) 1 No - Microprocessor based numericak relay with O/C, E/F and S/C protection.

e) 1 No - set of dual core dual ratio 3 CTs 100/5A of 15 VA burden and accuracy class 0.5 for metering and class 5P10 for protection.

f) 1 No. electronic type digital energy analyser having 30 days memory and parameters of KW, KWH, Power factor, frequency etc. Suitable for BMS compatible with all accessories.

g) 1 No. hooter with hooter acceptance and reset push button.

h) 1 No - Red, Yellow & Blue for phase indication.

i) 1 No - Amber for Trip indication.

j) 1 No - Red `ON' Green `OFF'indication.

k) 1 No - Spring charge indication.

l) 1 No - Auto trip indication.

m) 1 No. hooter with hooter acceptance and reset push button.

n) 1 No. master trip relay. ( Electromechanical Type )

o) 1 No.Trip ckt supervision relay. (Electromechanical Type )

a) Outgoing - 2 No, 630 Amp, VCB.

c) 2 No - Microprocessor based numericak relay with O/C, E/F and S/C protection.

d) 2 No - set of dual core dual ratio 3 CTs 100/5 A of 15 VA burden and accuracy class 0.5 for metering and class 5P10 for protection.

e) 1 No. electronic type digital energy analyser having 30 days memory and parameters of KW, KWH, Power factor, frequency etc. Suitable for BMS compatible with all accessories.

f) 2 No. hooter with hooter acceptance and reset push button.

g) 2 No - Red, Yellow & Blue for phase indication.

h) 2 No - Amber for Trip indication.

i) 2 No - Red `ON' Green `OFF'indication.

j) 2 No - Spring charge indication.

k) 2 No - Auto trip indication.

l) 2 No. hooter with hooter acceptance and reset push button.

m) 2 No. master trip relay. ( Electromechanical Type )

n) 2 No.Trip ckt supervision relay. (Electromechanical Type )

o) 2 No.auxiliary relay for transformer fault.

p) Power pack.

H.T. Panel described as above

TRANSFORMER

Design, manufacture, supply, installation, testing and commissioning of out door type copper wound transformer continuously rated for 3Ph 50 Hz at full load rating the transformer should have oil immersed winding having vector group DY-11, HT side connected in star with neutral brought out connected to provide separate earthing. The transformer shall have power terminal arrangement bushing / cable end box on HT side and cable end box on LT side. 315 KVA, 11 KV /0.415 KV, 3 phase, 4.5 % impedance, 50 Nos channels with stoppers shall be provided and fixed on the provided plinth for mounting the Transformer. The transformer should have following standard as per amended IS specification and the load * no load losses shall be limited to the values given below or as per IS 2026 and latest IS-1180 or Norms issued by SEB which ever are Lower.

Oil Conservator with filling hole with cap and plain oil level gauge.

Silica gel dehydrating breather charged with silica gel.

Oil drain Valve

Oil Filter Valve

Lifting eyes / Hooks

Two earthing Terminals

Diagram and rating plate

Air Vent

Explosion Vent

100 mm dia thermo meter with thermometer pocket

Four bi directional plain roller

Buchholz relay

Resistance Temp detector

Marshalling box

Automatic Voltage Regulator ( AVR)

Remote Tap Changing controller ( RTCC)

Transformer 11000/415 volts with on load Tap changer -15% to +5% in steps of 1.25% with RTCC, AVR and marshalling box and other specification as per BIS Level-2

11 KV END TERMINATION:

supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :

3C x 185 Sqmm, 11KV XLPE

11 KV H.T. CABLE:

Supplying of 11 KV grade aluminium conductor, cross linked polyethylene (XLPE) insulated individual core screened, flat steel/strip armoured PVC sheathed cable complete as required.

3C x 185 Sqmm, 11 KV XLPE

Laying of one number additional PILCA / PVC insulated and PVC sheathed / XLPE power cable of grade exceeding 1.1 KV but not exceeding 11 KV of size exceeding 120 sqmm but not exceeding 400 sq.mm direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning protective covering and refilling the trench etc. as required.

Supply & Laying of following sizes of 1.1KV grade Copper conductor XLPE insulated and FRLS PVC sheathed armoured control cable including termination conforming to relevant IS.

4 core, 2.5 sq.mm.

10 core, 2.5 sq.mm.

12 core, 2.5 sq.mm.

Supply & Fixing of Rubber mat 1000 mm. Wide to withstand 1.1 KV dielectric strength as per latest IS 15652-2006.

Supplying and Laying of Rubber mat 1000 mm. Wide to withstand 11 KV dielectric strength as per latest IS 15652-2006 etc. as reqd.

Supplying & Placing of First aid box as approved by St.John Ambulance Brigade /Indian Red Cross society conforming to IS : 2217 - 1963 etc as reqd.

Supplying & Installation of Shock treatment chart duly mounted on a wooden frame with glass on, as required in 2 languages (Hindi & English) etc. as reqd

EXTERNAL LIGHTING

S.I.T.C of Following rating LED Street Lighting luminare with pressure die cast housing and toughened glass cover (IP 66 protection ) in existing pole / pipe for supply voltage 100-270 AC 50Hz Luminare shall be confirm to IS :10322 part 5/ section-3 and shall be complete with all nessessary accessories as required.

60W LED Street Light

S.I.T.C of Following rating LED Post Top lamp made in die cast aluminium housing with decorative clear / opel acrylic diffuser on existing pipe including connection with 1.5sq.mm coppwr conductor etc all complete as required.

20/25W LED Post top lamp clear

S.I.T.C of Following rating approved make LED Bpllard Fitting with cylindrical shape and inverted cone shape head of height 600 to 850 mm power input -8/9 watt with die cast aluminium housing opel with PC diffuser, IP-65/54 protection, conferming to IS : 10322 part 5 etc all complete as requird. (Excluding Plinth Charge.)

Supplying & installation of 7 mtr. Height Octagonal Hot Dip galvanized pole (BOP. 7030) with top dia 70 mm bottom dia 130 mm & made of 3 mm thick sheet base plate dimensions 200x200x12 mm (LxBxT) including suitable size of foundation bolt all complete as required (without Arm).

1m Single Arm Suitable for 70MM Top

HVAC WORK

SUB-HEAD 'A' - AIR CONDITIONING EQUIPMENTS HIGH SIDE (VRV/VRF SIDE)

AIR COOLDED VARIABLE REFRIGERANT VOLUME/FLOW AIR CONDITIONING SYSTEM

Supply, Installation, testing and commissioning of air cooled Variable Refrigerant Volume/Flow modular type air-conditioning system Invertor Controlled with step less modulation complete with indoor and outdoor units, individual remote controller and centralized controller, interconnected refrigerant piping ,full charge of refrigerant gas & oil, control cabling etc.as per detail given in specifications and having following items: Refrigerant to be used shall be - R - 410 A.

OUTDOOR UNIT

Supply, Installation, testing and commissioning of Both Cooling & Heating Modular type outdoor units suitable to operate at 415 ± 10 % volt, 50 Hz, 3 phase AC supply and suitable for cooling application by using 100 % inverter driven capacity control compressors (Hermetically sealed scroll/Twin Rotary type) with stepless modulation complete with special acryl precoated heat exchanger, low noise condenser fan , auto check function for connection error in display panel, auto address setting as per specifications. The COP at AHRI conditions shall not be less than 4.2 . The units shall be complete with necessary mounting frames and capacity as mentioned below and as per specification.

The cost should include the following :

Nitrogen pressure testing for refrigerant pipe leakages & flushing during installation & after commissioning between IDU & ODU with flare nuts. Refrigerant gas & oil charging as per OEM standard.

Necessary corrosive treatment of copper coil of the ODU with Aluminum hydroxide, 25 microns thickness or equivalent coating as per manufacturer standard to protect from corrosion, sulfur and other chemical contaminants present in the air. The coating should be done in the presence of OEM representative. The coating shall be carried-out by the authorized applicator of coating manufacturer.

Note : The ODU provided with cowl duct for exhaust air should have minimum 5 mm ESP. GI wire mesh (minimum 16 SWG thickness) type bird screen with framing at the Mouth of exhaust air Cowl duct of Outdoor Units.

ODU Units Mounted on MS Frame/Masonry Pedestal with required anti-vibration mounting.

24 HP (2x12 HP)

30 HP (1x16 HP +1x14 HP)

42 HP (3x14HP)

CEILING SUSPENDED DUCTED TYPE UNITS

Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The unit shall have automatic force shut down provision in case of fire on receiveing signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature.

Indoor Units powder coated MS Hanging arrangement/wall Brackets/Spring Isolators with required anti-vibration mounting and Fire Rated Flexible Connection.

Mid Static Ductable units (minimum 50 pascal external static pressure)

1.1 TR (375 CFM)

1.3 TR (450 CFM)

1.6 TR (600 CFM)

Mid Static Ductable units (minimum 100 pascal external static pressure)

2.0 TR (725 CFM)

2.6 TR (875 CFM)

3.3 TR (1050 CFM)

High Static Ductable units (minimum 150 pascal external static pressure)

4.0 TR (1400 CFM)

4.6 TR (1650 CFM)

5.5 TR (2050 CFM)

Refrigerant Joints and Headers

Supply, Installation, Testing and Commissioning of copper Y-Joints sets, distributer and headers, suitable for various sizes of gas and liquid line of VRF System complete as required for the above system.

Corded/Cordless Remote Controller

Supply, Installation, testing and commissioning of self diagnostic type Corded/Cordless remote controllers for operation of indoor units.

Central Remote Controller

Supply, Installation, testing & commissioning of Main intelligent central controller with Scheduled Timer system Touch screen Type suitable for groups of indoor units to operate, monitor, on/off, cyclic operation setting, temperature setting etc. The CRC shall be provided with suitable size metallic box with lock arrangement.

Air Cooled Inverter Ductable Unit

Supplying, installing, testing and commissioning of Air Cooled Ducted Air conditioners suitable for R410A or eco-friendly refrigerant with evaporating unit comprising of cooling coil, blower with motor in Metallic (Steel) casing and condensing unit comprising hermetically sealed scroll compressor, condenser coil, and propeller fan. Unit shall be complete with controls, interconnecting copper refrigerant piping with insulation, Expension kit to connect with DX AHU, and electrical cabling etc. between evaporative and condensing unit, refrigerant gas and oil and complete as per specifications. The unit shall be suitable for operating on 240 volt, 1 phase, 50 Hz AC supply with five star energy rating. The units shall be suitable for chorded remote operation. The refrigerant piping & cabling shall run in PVC sleeve Steel supporting structure for outdoor units suitable for wall mounting / floor mounting.

Providing, fixing and testing of copper refrigerant piping of appropriate sizes duly insulated with nitrile rubber insulation of 19 mm thickness. The pipes plus nitrile rubber insulation and cable are to be covered with PVC flexible conduits for protection.

Note: Providing and fixing of Powder coated M.S. angle iron frame work/Masonary Pedastal with required anti-vibration mounting for outdoor unit is also included in the above scope. Contractor to submit design/Scheme for Iron frame and obtain approval of engineer/employer before proceeding purchase & installation.

Nitrogen pressure testing for refrigerant pipe leakages & flushing during installation & after commissioning between IDU & ODU with flare nuts. Refrigerant gas & oil charging as per OEM standard.

Necessary corrosive treatment of copper coil of the ODU with Aluminium hydroxide, 25 microns thickness or equivalent coating as per manufacturer standard to protect from corrosion, sulfur and other chemical contaminants present in the air. The coating should be done in the presence of OEM represantative. The coating shall be carried-out by the authorized applicator of coating manufacturer.

5.5 TR Ductable Split Unit -Only Condensing

8.5 TR Ductable Split Unit -Only Condensing

11.0 TR Ductable Split Unit

The vendor may offer the outdoor units as per availability from the manufacturer, however keeping the tonnage same as per BOQ subject to approval by Consultant/Client.

The indoor units capacity can be also as per availability from the manufacturer but keeping the minimum capacity as required in BOQ subject to approval by Consultant/Client.

AIR HANDLING UNITS

DOUBLE SKIN FLOOR MOUNTED AIR HANDLING UNIT WITH HEPA FILTER

(For OT With 10 ACPH/Hr)

Supply, Installation, Testing and commissioning of factory built floor mounted Direct Expension (DX Type) double skin type horizontal/vertical air handling units made of 50±1 mm thick panels consisting of pre plasticized G.I. casing of thickness 1.0 mm outside layer and 1.2 mm inside layer with polyurethane foam (PUF) insulation factory injected between them by injection moulding machine of density, complete with blower section with blower suitable for static pressure as required, minimum 2 bend GSS/ PVC eliminators, cooling coil section with aluminium finned copper tubes (tubes thickness not less than 0.5mm) cooling coil of 8 row deep, filter section with 50mm thick metal viscous/ washable synthetic type air prefilters, belt drive package with TEFC drive motor of efficiency class IE3 suitable for 415 ± 10% volts, 50Hz, 3 Phase AC supply suitably designed for variable frequency drive applications, drain connections, stainless steel (18G) drain pan with PUF insulation, 150 mm dia. dial type pressure gauges (2 nos.)and industrial type thermometers (2 nos.) at the inlet and outlet of coil, auto purge valve wherever required, necessary vibration isolation arrangement etc. complete as per specification.

The cooling coil made of Aluminium finned Copper tube with coil section, pre-filter section with non woven synthetic media of 10 micron particle size with an efficiency of 90% in both the supply & exhaust side of AHU, fine filter section with filters of non woven synthetic media of 5 micron particle size in supply after fan, (Hepa filters shall be at terminals along with laminar flow plenum & not to be included in the cost), mixing chamber complete with motor, belt drive etc. without face and bypass dampers. The AHU shall be accoustically insulated with 25mm thick open cell nitrile rubber & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section with starter panel. These AHUs shall have air inlet / outlet connection made of aluminium 20 G & all fixing arrangement / blank off shall be of SS, the complete AHU shall conform to standard specification. The face velocity across cooling coil shall be limited to 500 FPM (2.52 MPS) maxm & Fan outlet velocity shall be not exceed 9.0 m/s.

Casing shall be of panel construction; double wall type packed with pressure injected CFC free foam insulation minimum 50mm ± 1mm thick. Casing framework shall be of modular galvanized iron, aluminium or Approved equal pentapost double skin construction. Outer skin shall be minimum 1.0 mm galvanized steel sheet while inner skin shall be minimum 1.2 mm galvanized steel sheet. The sheets should have a minimum galvanisation of 275 GSM. The outer skin and inner skin should be precoated or powder coated on the exposed side

AHU shall be Eurovent certified. The mechanical performance of AHU shall be as per EN 1886. Rating performance for units, components and section shall be as per EN 13053. Fans shall be AMCA certified for

Cost shall be included for suitable rating Starter panel within MS enclosure near the fan with necessary power cabling & connection from Starter panel to fan motor.

3000 CFM Supply Air, 8 Row CC, 125 mm St. Pr., For Supply Fan, Supply Fan, 1200 CFM Ex. Air Blower, 40 mm St. Pr. for Exhaust fan with other accessories as specified)

DOUBLE SKIN FLOOR MOUNTED AIR HANDLING UNIT WITH FINE FILTER

Supply, Installation, Testing and commissioning of factory built floor mounted Direct Expension (DX Type) double skin type horizontal/vertical air handling units made of 50±1 mm thick panels consisting of pre plasticized G.I. casing of thickness 1.0mm outside layer and1.2 mm inside layer with polyurethane foam (PUF) insulation factory injected between them by injection moulding machine of density, complete with blower section with blower suitable for static pressure as required, minimum 2 bend GSS/ PVC eliminators, cooling coil section with aluminium finned copper tubes (tubes thickness not less than 0.5mm) cooling coil of 6 row deep, filter section with 50mm thick metal viscous/ washable synthetic type air prefilters, belt drive package with TEFC drive motor of efficiency class IE3 suitable for 415 ± 10% volts, 50Hz, 3 Phase AC supply suitably designed for variable frequency drive applications, drain connections, stainless steel (18G) drain pan with PUF insulation, 150 mm dia. dial type pressure gauges (2 nos.)and industrial type thermometers (2 nos.) at the inlet and outlet of coil, auto purge valve wherever required, necessary vibration isolation arrangement etc. complete as per specification.

The cooling coil made of Aluminium finned Copper tube with coil section, pre-filter section with non woven synthetic media of 10 micron particle size with an efficiency of 90% in both the supply & exhaust side of AHU, fine filter section with filters of non woven synthetic media of 5 micron particle size in supply after fan, mixing chamber complete with motor, belt drive etc. without face and bypass dampers. The AHU shall be accoustically insulated with 25mm thick open cell nitrile rubber & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section with starter panel. These AHUs shall have air inlet / outlet connection made of aluminium 20 G & all fixing arrangement / blank off shall be of SS, the complete AHU shall conform to standard specification. The face velocity across cooling coil shall be limited to 500 FPM (2.52 MPS) maxm & Fan outlet velocity shall be not exceed 9.0 m/s.

Casing shall be of panel construction; double wall type packed with pressure injected CFC free foam insulation minimum 50mm ± 1mm thick. Casing framework shall be of modular galvanized iron, aluminium or Approved equal pentapost double skin construction. Outer skin shall be minimum 1.0 mm galvanized steel sheet while inner skin shall be minimum 1.2 mm galvanized steel sheet. The sheets should have a minimum galvanisation of 275 GSM. The outer skin and inner skin should be precoated or powder coated on the exposed side

AHU shall be Eurovent certified. The mechanical performance of AHU shall be as per EN 1886. Rating performance for units, components and section shall be as per EN 13053. Fans shall be AMCA certified for

Cost shall be included for suitable rating Starter panel within MS enclosure near the fan with necessary power cabling & connection from Starter panel to fan motor.

10,000 CFM (25.0 TR), 65 mm St. Pr.,6 Row CC

DOUBLE SKIN CEILING SUSPENDED AHU

Supply, installation, testing and commissioning of factory fabricated Double Skinned Direct Expension (DX Type) Air- handling unit ceiling suspended type fabricated out of extruded aluminium section with 1.0 mm pre-plasticized / pre-coated Galvanised steel sheet outside & 1.2 mm plain Galvanised steel sheet inside with blower, blower section and blower motor TEFC type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 Row cooling coil made of Aluminium finned Copper tube with coil section, pre-filter section with non woven synthetic media of 10 micron particle size with an efficiency of 90%, polished stainless steel drain pan made out of 22 G sheet duly insulated complete with motor, direct / belt drive as mentioned below etc. without face and bypass dampers. All direct driven fan motor shall be sourced from fan manufacturer & factory fitted only. The AHU panels shall be insulated with 23mm thick & 36 Kg/m³ density PU foam. The motor & blower assembly shall be mounted on Aluminium extruded section only with starter panel. The complete AHU shall conform to standard specification.

The cooling coil made of Aluminium finned Copper tube with coil section, pre-filter section with non woven synthetic media of 10 micron particle size with an efficiency of 90%, complete with motor, belt drive etc. without face and bypass dampers. The AHU shall be accoustically insulated with 25mm thick open cell nitrile rubber with 20 G perforated Galvanised steel sheet & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section with starter panel. The complete AHU shall conform to standard specification. The face velocity across cooling coil shall be limited to 500 FPM (2.52 MPS) maxm & Fan outlet velocity shall be not exceed 9.0 m/s.

Casing shall be of panel construction; double wall type packed with pressure injected CFC free foam insulation minimum 50mm ± 1mm thick. Casing framework shall be of modular galvanized iron, aluminium or Approved equal pentapost double skin construction. Outer skin shall be minimum 1.0 mm galvanized steel sheet while inner skin shall be minimum 1.2 mm galvanized steel sheet. The sheets should have a minimum galvanisation of 275 GSM. The outer skin and inner skin should be precoated or powder coated on the exposed side

AHU shall be Eurovent certified. The mechanical performance of AHU shall be as per EN 1886. Rating performance for units, components and section shall be as per EN 13053. Fans shall be AMCA certified for

Cost shall be included for suitable rating Starter panel within MS enclosure near the fan with necessary power cabling & connection from Starter panel to fan motor.

2,000 CFM (5.5 TR), 40 mm St. Pr., 4 Row CC

3,000 CFM (6.0 TR), 50 mm St. Pr., 4 Row CC

KIT FOR AHUs

Supply, Installation, Testing and Commissioning of VRV Kits for AHUs having all controllers & Electronic Expansion Valve (EEV) and temperature set arrangement. It Shall have cut off arrangement after a particular set value of Supply air Temperature.

AHU Kits & Controllers

THERMOSTAT FOR AHU

Supply, installation, testing and commissioning of digital display type thermostat for air handling unit for cool / heat application suitable for four pipe system & humidistat suitable for working with humidifier and hot water coil control valves for various air handling Units.Controller have provision to display differential pressure accress OT if required. The thermostat shall have provision of setting of space temperature and display of the same.

The humidistat shall have provision of setting space RH and display of the same. The quoted price of thermostat / humidistat shall include the cost of 20mm MS conduits, control cabling, MS Box etc as required. The cost quoted shall be excluding the control valves and humidifier

Cooling / heating thermostat

HUMIDIFICATION PACKAGE

Supply, installation, testing and commissioning of Humidification package with all necessary controls as required as per standard specification & of following capacities:

LAMINAR AIR FLOW

Supply, installation & testing of factory fabricated Laminar air flow pattern perforated plenum made of 16 G aluminium sheet with hepa filters & suitable for operation theatre with all accessories as required to suit, site condition as per specifications.

SIZE-2.4mx2.7m

AIR COOLED DX TYPE SPLIT AC UNITS

Supply , installation, testing & Commissioning of ceiling suspended DX type split AC units with air cooled condenser complete with 5 Star Inverter type scroll/rotary compressor ,condenser ,wiring & accessories . Indoor units shall be ceiling suspended/wall mounted type complete with evaporator ,fan, filter ,drier, expansion devices & microprocessor control panel along with all accessories with refrigerant & oil charge , corded remote controls. The unit shall be suitable for working at 240 ± 10% ,50 Hz,1 phase AC supply .The unit shall be designed to take care of minimum vertical head 5mt & horizontal length of 30 mt & necessary oil separator shall be included ,Necessary supporting arrangement for both indoor & outdoor units ( Powder Coated /Epoxy painted MS stand for ODU units as per approved make, shade by Architect) with necessary vibration isolation arrangement as per site condition etc. (without condensate drain pipe ,electrical power & control cabling between indoor & outdoor unit which shall be paid separately ).

The coil in the outdoor units shall be provided with anti corrosive treatment. Necessary corrosive treatment of copper coil of the ODU with Blygold PoluAl (Aluminum hydroxide, 25-microns thickness) to protect from corrosion, sulfur and other chemical contaminants present in the air. Coating should be done in presence of OEM representative. The coating shall be carried-out by the authorized applicator of coating manufacturer.

The Outdoor unit Compressor must be provided with 5 Year Warranty Period.

Silver Ion Filter, Dust Filter

Civil Work such as wall hole making , wall chiseling ,refilling of chiseling part with mortar etc. as per site condition.

Nitrogen pressure testing for leakages & flushing during installation & after commissioning between IDU & ODU with flare nuts

Removable Covers for all indoor & Outdoor units shall be supplied & put on the units after installation & commissioning.

Incoming power supply shall be provided near each indoor units

SCHEDULED TIMER FOR SPLIT AC

Supply, installation, testing and commissioning of Scheduled Timer for wall mounted split type Air conditioning units.

TRANSMISSION & CONTROL WIRING

Supplying, installing, testing and commissioning of Shielded control cum transmission wiring of 2 core x 1.5 sqmm copper FRLSH, XLPE insulated cable in suitable GI conduits accessories between indoor and outdoor units. Necessary securing of conduit shall be made by contractor. After completion of work wall and floor shall be repaired and brought to its original finish. The rate will also include cost of laying of GI conduit between indoor and outdoor units.

2C x 1.5 Sq mm (Shielded-Unarmored)

REFRIGERANT PIPING

Supply, fixing, testing and commissioning of interconnecting soft/hard drawn copper refrigerant pipe work of following outer diameter duly insulated with fire rated class'O' closed cell elastomeric nitrile rubber type tubular insulation (19mm/13mm thick) between indoor & outdoor units & protected with 28 G aluminium sheet cladding as per specifications. All piping should be laid on Galvanized/Powder Coated tray supported by Galvanized M S Hangers & Clamps and all external piping shall run in covered cable trays. The rate includes all the items required to complete the piping work and nothing extra should be payable except the cable tray.

Vaccumiazation & Nitrogen pressure testing for leakages & flushing during installation & after commissioning between IDU & ODU.

Civil Work such as wall hole making , wall chiseling ,refilling of chiseling part with mortar etc. as per site condition.

6.4 mm outer dia Soft Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

9.5 mm outer dia Soft Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

12.7 mm outer dia Soft Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

15.9 mm outer dia Soft Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

19.1 mm outer dia Hard Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

22.2 mm outer dia Hard Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

25.4 mm outer dia Hard Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

28.6 mm outer dia Hard Drawn with Tube Thickness-1.2mm ( Insulation-19 mm )

31.8 mm outer dia Hard Drawn with Tube Thickness-1.62mm ( Insulation-19 mm )

34.9 mm outer dia Hard Drawn with Tube Thickness-1.62mm ( Insulation-19 mm )

38.1 mm outer dia Hard Drawn with Tube Thickness-1.62mm( Insulation-19 mm )

41.3 mm outer dia Hard Drawn with Tube Thickness-1.62mm( Insulation-19 mm )

DRAIN PIPING

Providing and fixing of cPVC drain water piping complete with fittings, flexible connection to IDU, necessary support as per specification and insulated with 6 mm thick fire rated class'O' closed cell elastomeric nitrile rubber insulation.

25 mm dia

32 mm dia

40 mm dia

AXIAL FLOW FANS

SMOKE EXTRACTION/EXHAUST FAN

Supplying, installation, testing and commissioning of AMCA Certified (For Air and Sound Performance) ceiling hung exhaust air tube axial flow fans of following capacity with GSS casing and aluminium alloy impellers with high efficiency aero-foil sections, blades, the impeller directly driven by TEFC induction motor should be of high efficiency class IE3 (as per IS 12615) suitable for 3 Phase 50 Hz 415V ± 10 %, of class 'H' insulation etc. including all accessories complete as required and as per specifications. Motor shall be of high temperature resistance "Class H Smoke Spill" 250° C for 2 hrs. Motor make shall be same as mentioned on the fire certificate. Fan total efficiency should not be less than 70%, noise level should not be more than 78 db. @ 3 m distance when measured in hemispherical reverberant room conditions. All the fans shall be hot dip galvanized with minimum 220 GSM Zinc Coating. Entire fan model & AMCA Seal shall appear in technical submittal of fan. Air moving capacity shall be as follows:

Cost shall be included for suitable rating Starter panel within MS enclosure near the fan with necessary power cabling & connection from Starter panel to fan motor.

Fan shall be supplied with Spring Isolators, Fire Rated Flexible Connection, GI gravity louvers, bird screen and fan guard.

Back draft Damper : Where required for system design roof-mounted fan shall be equipped with a rattle-free back draft damper to prevent air from re­ entering the fan when fan is not in operation, thus sealing completely in closed position. Damper shall be chatter proof under all conditions.

Note:-These fans would be connected to the fire alarm system & BMS system of the building and would start automatically in case of Fire

1. Outlet Velocity for normal mode fans not to exceed 10.0 MPS(Meter/Second)

2. Outlet Velocity for Fire mode fans not to exceed 12.0 MPS (Meter/Second)

3. Fan motor shall meet IE3 or above standard as per IS-12615

5. Thickness of casing : for dia( 315-630 )mm - 2mm , dia ( 710-1120)mm - 3mm , dia (1250-1400)mm - 4mm & dia 1600mm - 5mm.

6. In case of attenuator , calculation of reduction of sound level with insertion loss of attenuator is to be submitted.

2000 CFM (3400 CMH) at 25 mm static pressure

4000 CFM (6800 CMH) at 25 mm static pressure

10000 CFM (17000 CMH) at 25 mm static pressure -

AXIAL FLOW FANS (SUPPLY/PRESSURISATION FAN)

Supplying, installation, testing and commissioning of AMCA Certified (For Air and Sound Performance) ceiling hung Supply/ Pressurisation tube axial flow fans of following capacity with GSS casing and aluminium alloy impellers with high efficiency aero-foil sections, blades, the impeller directly driven by TEFC induction motor should be of high efficiency class IE3 (as per IS 12615) suitable for 3 Phase 50 Hz 415V ± 10 %, of class 'F' insulation etc. including all accessories complete as required and as per specifications. . Motor make shall be same as mentioned on the fire certificate. Fan total efficiency should not be less than 70%, noise level should not be more than 78 db. @ 3 m distance when measured in hemispherical reverberant room conditions. All the fans shall be hot dip galvanized with minimum 220 GSM Zinc Coating. Entire fan model & AMCA Seal shall appear in technical submittal of fan. Air moving capacity shall be as follows:

Cost shall be included for suitable rating Starter panel within MS enclosure near the fan with necessary power cabling & connection from Starter panel to fan motor.

Fan shall be supplied with Spring Isolators, Fire Rated Flexible Connection, GI gravity louvers, bird screen and fan guard.

Back draft Damper : Where required for system design roof-mounted fan shall be equipped with a rattle-free back draft damper to prevent air from re­ entering the fan when fan is not in operation, thus sealing completely in closed position. Damper shall be chatter proof under all conditions.

Note:-These fans would be connected to the fire alarm system & BMS System of the building and would start automatically in case of Fire

1. Outlet Velocity for normal mode fans not to exceed 10.0 MPS(Meter/Second)

2. Outlet Velocity for Fire mode fans not to exceed 12.0 MPS (Meter/Second)

3. Fan motor shall meet IE3 or above standard as per IS-12615

5. Thickness of casing : for dia( 315-630 )mm - 2mm , dia ( 710-1120)mm - 3mm , dia (1250-1400)mm - 4mm & dia 1600mm - 5mm.

6. In case of attenuator , calculation of reduction of sound level with insertion loss of attenuator is to be submitted.

Supply Fan

2000 CFM (3400 CMH) at 25 mm static pressure

4000 CFM (6800 CMH) at 25 mm static pressure

10000 CFM (20400 CMH) at 25 mm static pressure -

CABINET TYPE CENTRIFUGAL FAN :

Supply, installation, testing, commissioning of direct driven double skin Cabinet type centrifugal fan with 25mm thick PUF insulation fan section consist of Centrifugal Fan, forward curve, with radial tip double wheel, double inlet, consisting of motor, drive arrangement, aluminum common frame for fan and motor, cushy foot mounting, aluminum base frame for the unit, VCD on the outlet of fan, filter and accessories as per specification and drawing complete with 25mm thick five layer GI wire mesh filter, Structural frame with blank-off sheet, anchor fastener with vibration isolation Springs and starter panel.

Cost shall be included for suitable rating Starter panel within MS enclosure near the fan with necessary power cabling & connection from Starter panel to fan motor.

Fan and motor shall be fire rated to 250 Deg C for 2 hours or as indicated in the specifications

The motor shall be spark-proof. The starter panel shall be provided with in-built timer to switch OFF the fan after a preset time (say 300 seconds) once triggered

Note:-These fans would be connected to the fire alarm system/BMS System of the building and would start automatically in case of Fire

1. Outlet Velocity for normal mode fans not to exceed 10.0 MPS(Meter/Second)

2. Outlet Velocity for Fire mode fans not to exceed 12.0 MPS (Meter/Second)

5000 CFM with 35 mm static Pressure

AIR WASHER :

Supply, Installation, Testing & Commissioning of factory fabricated Double Skinned Air-washer unit floor mounted type fabricated out of extruded aluminum section with 0.8mm pre-plasticized /pre-coated Galvanized steel sheet outside & 0.8 mm plain Galvanized steel sheet inside with blower, blower section and blower motor TEFC type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply. Air washer having minimum 90% efficiency with consisting of centrifugal fan, mounting arrangements, mentalistic vibration isolation, belt drive arrangement, VCD, distribution headers, access door, pump, stainless steel water tank, suction screen, impregnated cellulose paper fills, nylon prefilter, GI ‘B’ class piping & associated works, quick fill, makeup & drain connections with butterfly & float valves etc. complete as per specifications & drawings. The unit shall be fire retardant, water proof double flexible connection at fan outlet and with starter panel.

Filters section shall incorporate synthetic washable filters of at least 50 mm thickness in suitable aluminum frame. Velocity of air across the fillers shall not exceed 500 fpm (2.5m/s). Outlet Velocity for fans not to exceed 10.0 MPS(Meter/Second)

Cost shall be included for suitable rating Starter panel within MS enclosure near the fan with necessary power cabling & connection from Starter panel to fan motor.

4000 CFM with 50 mm static Pressure

INLINE FAN (Ceiling suspended)

Supply, installation, testing, commissioning of Inline fan with vibration isolators, speed regulator, GI gravity louvers, Bird Screen and required cable as per specification and drawing. The Motor shall be suitable to run on 1 phase/50 hz/ 220 v electrical power Supply including fire retardant non-porous double layer flexible connection of the following capacity.

The louvers & bird screen shall be made of heavy gauge metallic construction.

200 CFM (340 CMH) at 10 mm static pressure

300 CFM (510 CMH) at 10 mm static pressure

400 CFM (680 CMH) at 10 mm static pressure

500 CFM (850 CMH) at 12 mm static pressure

600 CFM (1020 CMH) at 12 mm static pressure

800 CFM (1360 CMH) at 12 mm static pressure

1000 CFM (1700 CMH) at 15 mm static pressure

PROPELLER FAN

Supply, installation, testing and commissioning of wall mounted Propeller type heavy duty exhaust Fan of metallic construction complete with speed regulator, bird screen, gravity louvers, vibration isolators, required cable, plug & other accessories compete as required, suitable for single phase, 240± 10 volts, 50Hz AC. supply of following capacities:

The louvers & bird screen shall be made of heavy gauge metallic construction.

300 mm sweep dia (900 RPM)

Supply, installation, testing & commissioning of Wall mounted Propeller type exhaust air fans of high grade ABS plastic construction complete with electric motor suitable for operation on 230 V+ 10%,50 Hz, 1 phase AC supply fitted with speed regulator, mountings frames, louvers and bird screen, required cable & plug to connect with socket etc. complete as required of following capacities.

250 mm sweep dia

DUCTING FOR AIR CONDITIONING / VENTILATION

FACTORY FABRICATED GALVANIZED STEE(GSS) SHEET METAL DUCTS

Supply, installation, testing and commissioning of factory fabricated Galvanized Steel (GSS) Sheet metal ducts complete with flanges, neoprene rubber gasket, elbows, Splitter Damper, vanes, hangers & support etc. as required as per IS/DW144/SAMACNA standard & confirming to specification. Duct shall be furnish at site in "L" shape or box shape from factory. The rates shall include all materials of the duct and labour for suspension and supporting arrangement for plenums, ducts, complete with fire retardant flexible connection as required and as per specifications.

Note : Splitter Shall be a part of ducting.

0.63 MM (24 Gauge )

0.80 MM (22 Gauge )

1.00 MM (20 Gauge )

1.25 MM (18 Gauge) Plenum

SITE FABRICATED GALVANIZED STEE(GSS) SHEET METAL DUCTS

Supply, Fabrication, installation and testing of Galvanized Steel (GS) sheet metal ducts & finally applying fire rated paint as per BS 476 Part 24 (Site FABRICATED DUCTS For Connection /Plenum etc.) in accordance with the approved shop drawings complete with all accessories like vanes, flanges, suspension rods , anchor bolts, GI bolts & nuts, etc., as per specifications.

Site fabricated GSS sheet metal rectangular ducting as per IS 655-2006

0.63 MM (24 Gauge )

0.80 MM (22 Gauge )

1.00 MM (20 Gauge )

1.25 MM (18 Gauge)

FIRE RATED FACTORY FABRICATED GALVANIZED STEE(GSS) SHEET METAL DUCTS

Supply. Installation, testing and commissioning of Fire rated sheet metal ducts shall be fabricated from Lock Forming Quality grade prime galvanized steel sheet with flanges complete with supports, vanes, dampers, links, levers and quadrants etc. as per specifications and drawings. Supporting distance shall not exceed 1.2 Mtr with 6mm thick fire retardant gasket suitable for 250 deg C 2 hr shall be used in duct joints along with fire sealants. Suitable access doors shall be provided at every 3m. Duct shall be furnish at site in "L" shape or box shape from factory. The rates shall include all materials of the duct and labor for suspension and supporting arrangement for plenums, ducts, complete with fire retardant flexible connection as required and as per specifications.

All fire rated duct, smoke exhaust ducts shall be quoted with flame bar BWII or equivalent to achieve the required fire rating, also all the related accessories gaskets shall be suitable for the required fire rating.

Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006

1.25 MM (18 Gauge) Plenum & Exhaust Duct

ALUMINIUM (AL) DUCTING FOR OT

Supply, installation, testing and commissioning of factory fabricated Aluminium Sheet metal ducts complete with flanges, neoprene rubber gasket, elbows, Splitter Damper, vanes, hangers & support etc. as required fot OT and as per IS/DW144/SAMACNA standard & confirming to specification. Duct shall be furnish at site in "L" shape or box shape from factory. The rates shall include all materials of the duct and labour for suspension and supporting arrangement for plenums, ducts, complete with fire retardant flexible connection as required and as per specifications.

The joint between the ducts shall be done by means of polymer “flange / slide-in channel” system to prevent air leakages. Turning vanes, elbows and reducers to be considered as part of supply of ducts. Ducts shall be supported by cable supports / GI slotted channels with threaded rods. Internal Stiffeners shall be used to prevent bulging of ducts for the sizes above 800 mm.

0.80 MM (22 Gauge ) With 32mm Insulation

1.00 MM (20 Gauge ) With 32mm Insulation

1.25 MM (18 Gauge) With 32mm Insulation

Duct Insulation

Supplying , installation, testing & commissioning of external thermal insulation on ducts with Closed Cell Elastomeric Nitrile Rubber Insulation of density not less than 50±5 Kg/m³ & thermal Conductive not exceeding 0.032 W/mK at an average Temperature of 0°C and . The Material Shall be rated as Class 1 as per BS476 Part7 for surface spread of flame test and Class O as per BS476 part6 for fire propagation test. The Material shall have Fire Approval from CBRI - Roorkee & no toxicity under flaming and non- flaming condition as per AITM 3.000 (1993). Adhesive used for setting the insulation shall be non - flammable, Vapour Proof. All Joints should be sealed with 3 mm thick 50 mm wide PE tape and Flange to be overlapped by 6" width of the same material thickness. Finally Duct insulated should be strapped by 12mm metallic Packing strip at every random meter & conforming to standard and Specification.

ACCOUSTIC LINING

Duct Acoustic Lining

Supply and fixing of acoustic lining of supply air duct and plenum with thick Engineered Nitrile Rubber open cell foam having a Noise Reduction Coefficient of 0.55 with Density 160 Kg/m3 passing Class 1 Fire Performance test as per BS 476 Part 7, Air Erosion test for 10,000 fpm air velocity as per ASTM C 1071-05 and with built-in antimicrobial protection. The material should pass Fungi Resistance Test as per DIN EN ISO 846 Method A and Bacterial Resistance Test as per DIN EN ISO 846 Method C; to be applied using manufacturer's recommended Rubber based Adhesive in a blend of solvents.

Acoustic lining in ducts/plenum up to 5.0 Running meter from Fan Outlet as per specification and drawings.

20 mm For Duct

25 mm For Plenum

CONTROL DAMPER

VOLUME CONTROL DAMPER

Supply,. Installation, testing and commissioning of 18 Gauge G.I construction Frame with 22/24 Gauge GI Aero foil blades Volume control Duct/Wall Dampers with linkages, levers & fittings for Controlling the Airflow in Ducts with neoprene rubber gaskets,nuts, Bolts, Screws Linkages, Flanges etc. as per specification.

MOTRIZED VOLUME CONTROL DAMPER

Supply, installation, testing and commissioning of Motorized (ON-OFF Type) duct mounted GI volume control damper with enthalpy sensor and necessary control wire (minimum 1.5 sqmm) for integration within AHU room.

Motorized (ON-OFF Type) duct mounted GI volume control damper

Motorized (ON-OFF Type) duct mounted GI volume control Actuator

BACK DRAFT DAMPERS

Supply, Installation, testing and commissioning of 18 Gauge G.I construction Back draft Dampers for Controlling the recirculation of air with neoprene rubber gaskets,nuts, Bolts, Centrifugals Linkages, Flanges etc. as per specification. Louvres shall be made powder coated extruded aluminum.

PRESSURE RELIEF DAMPERS

Supply,. Installation, testing and commissioning of 18 Gauge aluminum alloy extrusions with welded/cleated frames Pressure Relief Dampers for Controlling the Excess pressure up to 60pa with neoprene rubber gaskets,nuts, Bolts, Centrifugals Linkages, Flanges etc. as per specification. Louvres shall be made powder coated extruded aluminum with suitable thickness.

AIR TERMINAL (SUPPLY/RETURN/EXHAUST)

Supply, installation, testing and commissioning of 50 micron Powder coated Aluminum extruded Air Terminal (Diffuser/Grille) as per specification & and drawings including fixing frames of GI in False ceiling/wall.

Grilles

Supply. Installation, testing and commissioning of powder coated extruded aluminium section grills with aluminium dampers for supply air terminal and grilles without damper for return air for air-conditioning as per specification.

Grilles with Dampers

Grilles without Dampers

Diffusers

Supply. Installation, testing and commissioning of powder coated extruded aluminium square diffusers with antismudge ring and removable core.

Supply air with dampers

Return air without damper

Flexible Duct

Supply. Installation, testing and commissioning of thermal flexible aluminum duct of following sizes duly supported at regular interval as per site requirement & spefications.

Slot Diffusers

Supply. Installation, testing and commissioning of slot diffusers with/without damper as specified below and as per specification.

3-Slot Diffuser

2-Slot Diffuser

Linear Grille

Supply. Installation, testing and commissioning of powder coated extruded aluminum Linear Grille.

Air Transfer Door Grille

Supply and fixing of non vision air transfer door grille of powder coated extruded aluminium, single deflection grille with horizontal vanes arrangement etc. as per specifications and drawings.

Exhaust/Fresh Air Louvers

Supply, Installation, Testing and Commissioning of Fresh Air/Exhaust air Louvers minimum 80 mm deep comprising of inclined blade and extended-out lowest blade for disposal of rain water including the wire mesh, filter (washable type filter section Class-G3 having efficiency >80% down to 20 micron fitted in aluminium frame) . The louver shall be of extruded Aluminum construction, and powder coated to the approved finish and color.

FIRE DAMPER

Motorized Fire Dampers With Actuator

Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications.

Duct/Wall mounted multi blade, motorised fire & smoke dampers with spring return actuator. The damper shall be of at least 1.5 hr. fire rating and actuated with the help of 24 V electric actuator excluding. The damper shall be as per UL listed UL 555; 1995 and CBRI approved. The damper shall be constructed out of 16G galvanised steel sheet & as per specification with Control Cable to Potential Free Contact for tripping of AHU fan motor.

Supply, installation, testing and commissioning of Motorised Spring Return Actuator for devices up to 0.8 sq. meter with control panel & temperature sensor.

Fire Damper

Actuator

Under Deck Insulation of Exposed Roof

Providing and Fixing Underdeck Insulation with 50 mm thick with closed cell Nitrile Rubber with prelaminated Aluminum foil on one side having a low stable k value of 0.035 k.cal/hr.m at 10.C and minimum density of 40-55 ± 3 kg/cum.The R-value should be as per ECBC Code.

ISOLATOR FOR OUTDOOR UNIT

Supply, Installation, Testing & Commissioning of following Switchgears as an Isolator in IP-65 rated in power coated 16 SWG sheet steel enclosure .

40A 4P MCCB(25 KA)

63A 4P MCCB(25 KA)

POWER CABLING

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender.

Supply and laying ,testing and commissioning of following sizes of Copper conductor control cables with PVC conduit & fixing clamps and effecting proper connections to equipment etc. of following sizes :

4C x 16 Sq. mm Copper Conductor (Armoured)

4C x 10 Sq. mm Copper Conductor (Armoured)

4C x 6 Sq. mm Copper Conductor (Armoured)

4C x 4 Sq. mm Copper Conductor (Armoured)

EARTHING STRIP/WIRES

Supplying and laying 6 SWG G.I. wire at 0.50 meter below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supply & laying 25x5mm GI strip at 0.5mt below ground as strip earth electrode including connection/terminating with GI nut,bolt,spring,washer etc. as required.) jointing shall be done by overlapping &with 2sets of brass nuts bolt spring washer spaced at 50mm)

25mm x5mm

MEDICAL GASES PIPELINE SYSTEM

Supply, Installation, Testing & Commissioning of Medical Gases Pipeline System complete with followings as per technical specifications & list of acceptable makes attached.

Oxygen System

Oxygen Manifold 6+ 6 cyclinder banks (cylinder excluded)

Automatic Control Panel for the Oxygen Manifold System.

Emergency Oxygen Manifold 2 + 2 cyclinder banks (cylinder excluded)

Oxygen Flowmeter with humidifier Bottle with probe

Oxygen Gas outlet points with probe/adaptor.

Oxygen H.P.Rubber tube (White)

Wall box for oxygen outlets

Nitrous Oxide

Nitrous Oxide Manifold 2 + 2 cyclinder banks (cylinder excluded)

Automatic Control Panel for the Nitrous Oxide manifold System.

Emergency Nitrous Oxide Manifold 1 + 1 cyclinder banks (cylinder excluded)

N2O Gas outlet points with probe/adaptor.

N2O H.P.Rubber Tube (Blue)

Compressed Air System

Compressed Air system of capacity 4x15HP Reciprocating Air Compressors, 1618LPM, 57 CFM, Air Dryers / Air Filters, Pre-filters, Activated Carbon Filters, Vertical Air Receiver of capacity 1500 Ltrs & Pressure Reducer

Medical Air 4 Bar Gas outlet points with probe/adaptor

Surgical Air 7 Bar Gas outlet points with probe/adaptor.

MA-4 H.P.Rubber Tube (Black)

Vacuum System

Vacuum system of capacity 4x7.5HP Reciprocating Vacuum Pumps, 111 CFM, Vertical Air Receiver of capacity 2000 Ltrs

Vacuum Gas outlet points with probe/adaptor.

Ward suction Unit with 1000ml Jar

Theatre Suction Unit with 2000ml Jar

Vacuum H.P.Tube antistatic tube (Yellow)

Wall box for Vacuum outlets

Area Alarm Panels

6 Gases

5 Gases

4 Gases

3 Gases

2 Gases

Master Alarm

Area Valve box units

6 Gases

5 Gases

4 Gases

3 gases

2 gases

Medical Grade Isolation Valves

Medical Grade Copper Pipeline (In Mtrs.)

12 mm (OD) x 0.9 mm Thickness

15 mm (OD) X 0.9 mm Thickness

22 mm (OD) X 0.9 mm Thickness

28 mm (OD) X 0.9 mm Thickness

42 mm (OD) X 1 mm Thickness

54 mm (OD) X 1.2 mm Thickness

Electrical Control Panel for Compressed Air System and Vacuum System with wiring inside the plant room

MODULAR OPERATION THEATRES

Wall and Ceiling Cladding (Approved MAKES : JINDAL/TATA/ESSAR)

Prefabricated Walls & Ceiling

Providing and installing Walls & ceiling panels, constructed with 0.8 mm Stainless steel 304 grade PUF Panels with tongue and groove mechanism for jointing and minimum width of 1200mm. The puff panel shall be made by injecting high pressure polyurethane foam with minimum density 40 kg/m3. The thickness of wall panels shall be 50 mm thick and ceiling panel shall be 30 mm thick. The inner surface walls will be fixed to the bricks wall with essential supports. The individual wall panels will not be spot welded together so as to ease removal for maintenance at a later date. All joints will be filled with metal filler and sanded flush on site ready to receive the plastic finish.

Antibacterial / Antifungal Paint

Providing and applying Antibacterial Paint: The internal surfaces of the room

walls will be sprayed with water based liquid plastic, wall glaze or equivalent anti-bacterial paint, approved by the architect to a minimum dry film thickness of 300 microns. The plastic coating will overlap the floor covering ceiling system and doorframes by 25mm to provide a continuous sealed surface. The plastic coating will be non- reflective and the Colour will be submitted to the architect for approval.

Laminar Air Flow System

SITC of Ceiling filtration system 2400x2400mm: The ceiling filtration system shall be 2.40 meters x 2.40 meters and will be integrated with the adjacent false ceiling. The ceiling shall be constructed with a plenum box supplied with conditioned air from the central system via 8 nos. HEPA filters (European Norm EN 1822:2009; Class H 14; DOP 99.97-99.9999% efficiency for 0.3 micron particles) with pressure drop of 300 Pascal’s at its nominal flow rates (supplied with the Plenum), mounted on the exit from the supply ducting.

Conductive Seamless Flooring with Coving on all Corners

SITC of Operation theatre flooring (antistatic conductive) : 2 mm Full Body Conductive Vinyl, laid on a semiconductive adhesive base. The floor finish should terminate at the room perimeter passing over a concealed cove former and continuing up the wall for 100mm. All joints should be welded with electrodes of the same compatible material to provide a continuous sealed surface

Hermetically Sealed Sliding Door System

Fabrication, Supply, installation, testing & commissioning of sliding type Hermetically Sealed OT door having high density particle board cores, high pressure laminate face on both sides, viewing window 300 x 300mm. Size: 1800 x 2100 mm (W x H). Automatic Doors: Provided with Radar Switch - 2 Nos., Foot Switch - 2 Nos. and Photocell Sensors (Anti Crush Feature) & as per tech. specs. attached.

Automatic Door (1800 mm x 2100 mm)

Automatic Door (1000 mm x 2100 mm)

Surgeon Control Pane

Supply, installation, testing & commissioning of Operation theatre control panel Membrane type :

· Time Day Clock

· Time Elapse Clock

· General and RGB Lighting System control (Peripheral Lights and plenum lights with dimming)

· Medical Gas Alarm Panel 5 Gas – low, normal and high pressure with sequencing as per HTM 02 01

· Hand Free Telephone set with speaker

· Temperature & humidity indicator with controller

· HEPA Filter Status module

· Room Pressure Indicator / differential pressure indicator

· USB Stick port

X-Ray View Screen

Supply, installation, testing & commissioning of Twin Plate LED X ray viewing screen: Size: 940 x 640 x 50 mm approx. with viewing area, Two plate X-ray view screen (120 W), LED based technology with colour temperature > 6000K and lamp life >50,000 hrs and brightness in excess of 4000 lux.

Writing White Board

Supplying & fixing of sturdy writing Operating list board: made of ceramic surface having Magnetic properties and should be flushed to the wall of the operating room. Size 940mmx640mmx50mm

Pressure Release Damper

Supply, installation, testing & commissioning of SS Fabricated Cascade Pressure relief dampers: Suitably sized air pressure relief damper should be placed enabling differential room pressure to be maintained. Counter- weight

balancing system should be provided in the PRD to maintain positive pressure inside the operation room.

Peripheral Lights

Supply Installation and Commissioning of 42W Bottom Opening Room fixture with IP 65, Led make should be Nichia /Seoul < 5 SDCM , Own make BIS certified Islocated Driver , Flicker Free , Class 2 SELV driver, Operating temperature: -10°C to +45°C, Operating voltage range: 140-270V, Surge protection >3.5 KV, High Efficiency driver: 80-85% ,Low Voltage Cut Off below 130V, Output short circuit protection , Fixture Made up of MS powder coated white after phosphochromate treatment provided as standard with sheet thickness of 1.2MM, Diffuser of High impact polycarbonate opal diffuser with thickness 1.5MM for glare free uniform light distribution, power coating : 60 Microns , Lamp Source :High efficiency long life LED package in integral module with lumen efficacy of >140 lm/W and viewing angle of 120° to ensure better uniformity,Average life L70B50: 50000 hours, THD<10%, PF>.95, System efficacy >95-100 Lm/W, CRI>80 ,IP65, IK05 Impact rating, . Dimension Will Be 1240X330X115mm, Safety test as per IS:15885 Part 2/Sec 13.

Surgeon Pendant

Providing & fixing of Ceiling mounted Single arm pendant systems for surgeon: The Weight carrying capacity of the arm should not be less than 180 Kgs load. There should be 5 or 6 nos. equipment loading shelves. double column of 1000mm. Single Arm Pivot range minimum 900mm or above. The brake (Electromagnetic) supplied with Indian Origin Multipin 6/16amp electrical switch + socket – 5 nos., It should have 2 no. RJ 45 data socket. It should have provision for 06 gas outlet points

· 2 Oxygen,

· 1 Vacuum

Capable of 340 degrees of rotation. Medical gas terminal units shall be provided by the MGPS vendor and shall be installed in the pendant.USFDA

Anaesthesia Pendant

Ceiling mounted rigid pendant systems for anaesthesia: Single Arm motorized type pendants Made of Aluminum, powder coate with electromagnetic Brakes Swivel angle 0-330 degree

Dimensions: Double Vertical column 1200 mm

Vertical lift: 600 mm Horizontal arms – total 1000 mm Pendant should be prepiped Provided with 5 nos medical gas outlets. Outlets shall be connected to dual circuit being provisioned for all Oxygen 2 outlets Nitrous Oxide 1 outlets Vacuum 1 outlets Medical Air 1 outlets AGSS 1 outlet colour coded high pressure tubing for each gas with NIST connectors at ceiling Provided with prewired 10 nos 6 / 16 amps sockets and two data sockets RJ 45

Instrument loading capacity 180 kgs. Shelves:

Two with handle and two rails each with capacity of 40 kgs Drawers one with handle and two rails

load capacity 40 kgs Swiveling stainless steel vertical pole

Scrub Station

Supplying, Installation, Testing & Commissioning of floor mounted, Scrub station: Compact surgical 2 bay scrub sink designed for use in OT complex. Each fixture fabricated from heavy gauge 1 mm thick type 304 stainless steel of seamless welded construction, polished to a smooth finish with a front access panel which should be easily removed for access to the water controlled value, waste connections, stoppers and strainers. Hands free operation should include infra-red sensors with built-in range of adjustment. Thermostatic mixing, valve control should be located behind the access panel and maintain constant water temperature. User defined setting of approximately 1 to 3 min should be available.

(Size: 1500mm X 675mm X 1105mm for 2 persons)

Electrical DB

SITC of Electrical distribution board: should house the transformers, if any, mains failure relays, electrical distribution equipment and circuit protection equipment for all circuits within the operating theatre. All internal wiring should terminate in connectors with screw and clamp spring connections of the Clip-on type mounted, on a DIN rail and labelled with indelible proprietary labels. Individual fuses or miniature circuit breakers should protect all internal circuits.

Storage unit:

Storage unit: 1 mm thick Stainless Steel sheet 304. The storage unit should be divided 4 equal parts and each part should have individual swing 8 mm toughened glass doors with high quality stainless steel self-closing hinges capable of 180 degree swing out and secure locking system. Each part will be provided with removable stainless steel racks made from ½” circular (outer diameter) seamless Stainless Steel 304 tubes of 1 mm thickness placed at intervals of 1.5” center to center. The overall dimension of the storage unit shall be 1500mm (Width) x 2100mm (Height), 350mm depth being variable to suit architectural layout.

LED Operating Light

LED operating light having following specifications:-

Maximum luminance (1m): 160,000 + 160,000 Lux at 1m distance, Electrical power: 150 + 90 W, Power consumption: 2x 11 A, Fitting: Ceiling anchoring ring ceiling pendant with 2 brackets and 2 spring arms, Range of movement: 1x 360° / 1x 330°, Recommended room height: at least 2.45 m, Max. ceiling load: 2x 218 Nm / 650 N, Light body weight: 9.2 + 7.5Kgs, Light body depth: 1x 130 cm / 1x 140 cm, Air shielding surface: 2 x 330 cm2 Transformers: 2x 450VA/230V/26V, Brightness regulator: 2x 20 – 500 VA (primary voltage), Provided with 2 Sterilisable handles with each dome, Easy positioning by sterilisable handle, Focus adjustable by sterilisable handle, Life time of Bulbs : 50,000 hours

MGPS Inside OT

MINOR OPERATION THEATRE

Wall & Ceiling Cladding

Prefabricated Walls & Ceiling

Providing and installing Walls & ceiling panels, constructed with 0.8 mm Stainless steel 304 grade PUF Panels with tongue and groove mechanism for jointing and minimum width of 1200mm. The puff panel shall be made by injecting high pressure polyurethane foam with minimum density 40 kg/m3. The thickness of wall panels shall be 50 mm thick and ceiling panel shall be 30 mm thick. The inner surface walls will be fixed to the bricks wall with essential supports. The individual wall panels will not be spot welded together so as to ease removal for maintenance at a later date. All joints will be filled with metal filler and sanded flush on site ready to receive the plastic finish.

Antibacterial / Antifungal Paint

Supply & laying of water based aseptic & self sterilizing wall coating with Anti fungal & Anti Bacterial Paint and other related painting components (viz: Primer, Putti etc.) of approved make and shadesso as to present a joint less finish etc. as per tech. specs. attached.

Conductive Seamless Flooring with Coving on all Corners

Supplying and laying of 2mm thick washable anti static seamless flooring with perfectly curved flash coving, resistant to mechanical stresses & dynamic loads & having ESD / EMI (conductive) protection characteristics. (Approx.), Coved Corners of approved make & shade. The joints of PVC tiles should be welded by special PVC thermal welding units using PVC welding bars colours. It should be scratch proof. The PVC flooring should be inert to body fluids, chemicals and disinfectants and should not be affected by temperature variation in the OT. The floor should efficiently discharge electric charges up to 2 kV. The conductive copper grid laid underneath the PVC sheet should be supported by liquid epoxy compounds allowed to set as a uniform and level surface & as per technical specs attached.

Hermetically Sealed Sliding Door System

Fabrication, Supply, installation, testing & commissioning of sliding type Hermetically Sealed OT door having high density particle board cores, high pressure laminate face on both sides, viewing window 300 x 300mm. Size: 1500 x 2100 mm (W x H). Automatic Doors: Provided with Radar Switch - 2 Nos., Foot Switch - 2 Nos. and Photocell Sensors (Anti Crush Feature) & as per tech. specs. attached.

Automatic Door (1500 mm x 2100 mm)

Surgeon Control Panel

Supply, installation, testing & commissioning of multi colour coded Surgeon Control Membrane Membrane Panel, flushed in the theatre wall comprising of the following features & as per technical specification attached: 1. Display of Day Clock 2. Display of Elapse Time Clock 3. Dimmer for peripheral lights 4. Medical Gas Alarm 5. Hands free telephone 6. Indicator for temperature & Humidity

Peripheral Lights (Dimmable)

Supply, installation, testing & commissioning of Recess Mounted IP54 LED clean room protocol, non–hygroscopic peripheral lights having CRCA housing lumen pack of 5600Lm with system wattage of 60 watt. The fitting should be Bottom opening type with high reflected clear acrylic glass with dimmer control from the Surgeon Control Panel. Specially designed for Clean Room Applications, such as Modular OT & as per tech. specs attached.

Surgeon Pendant

Providing & fixing of single arm (900mm) Surgeon pendant with load carrying capacity of 80Kg and rotational values of 330-340 degree with adjustable stopper. The pendent should be designed with service head to host, base, gas module, electric modular and shelves upto 8 gas outlets & 10 Electrical switches. Racks & Shelves should be provided to mount the equipments like monitor etc. The surgeon pendent should have Single arms as per technical specs attached.

Electric Distribution Box, Wiring, Conducting, Electrical Boards & Other Electrical Fittings - upto the Distribution Box

MGPS Piping Work with in the theatre

CURTAIN & IV HANGER SYSTEM

Supply, Installation, Testing & Commissioning of Curtain & IV Track System complete with following as per technical specifications attached.

Providing and installation of Cubical tracks system made of Powder coated Aluminium alloy, mounted on the ceiling using Suspension hangers and bushes, powder coated wall bracket and Track Joiners wherever required. This system shall be complete with stain free polyster fabric, Water repellent Curtains having 18" Net on top. The curtain shall be approx 7X4 feet, with two curtains stiched together wherever required. Curtains shall also be provided with smooth movement, non sticking runners, with Stainless steel hooks, for easy movement. The system shall have curtain removal points and end cap complete as per technical specifications wherever is required.(Acceptable Makes : Hitech Surgical Co. / Medikraft / Med Freshe)

Providing and installation of I.V. Hanger with 5 hooks, made from mirror finish stainless steel, 304 grade with adjustable height, provided with 4/6 feet aluminium alloy track powder coated with endcap of tracks, 1 pc of trolley for smooth IV Hanger movement on track, 2 pcs of suspension hanger powder coated, top & bottom bush, powder coated, for easy fitting and better aesthetics complete as per technical specifications is required.(Acceptable Makes :Hitech Surgical Co. / Medikraft / Med Freshe)

CSSD WORK

Horizontal Rectangular High Pressure High Vacuum Double Door Sterilizer.

The sterilizer will be manufactured as per IS:No.3829 (Part 1)-1978 with ISI Mark. The unit will be designed for operating pressure 30 to 32 psi. and corresponding to a temperature of 134oC. The sterilizer chamber would be formed out of SS 316. The Jacket will be formed out of mild steel. The jacket outer cover will be of SS 304. The sterilizer will be provided with 2 Nos. pressure locking type hinged doors. The door plate will be of SS 316 with shooting bolts,flush mountings and steam generator will be of SS 304. The stand of the sterilizer will be of mild steel. The Sterilizer will be automatic with PLC with 5 pre-sets programs and 1 variable program,. Sterilizer as above of chamber size 300 mm x 300 mm x 600 mm depth (1’x1’x2’) suitable for electrical operation on 400/440 volts, 3 phase, AC supply, electrical load 21 KW.300 x 300 x 600 mm-Capacity 100 liters.

Stainlesss Steel 316 carriage suitable for Rectangular Sterilizer

Stainlesss Steel 304 trolley suitable for above carriage

S.S. Control and packing table with drawer

table is used for separation, control and packing of various sets of sterilized goods for wards, clinics, operation theatres etc. and is designed for standing and sitting workers. A removable hatch made of laminated particles board is provided. The hatch contains a SS drawer and a laminated particles board plate. Overall size: 2000mm L x 1400mm W

Stainless steel Work Table

Table is used for wet goods with undershelf. The table top is fabricated out of 16 SWG SS 304 qlty. ground and polished to a smooth surface without high edge sections. The table top frame is a complete assembly with front, back and two ends welded together at corners. Overall size 1500mm x610x890Ht.

Stainless steel work table with two sink

The bench top is fabricated out of 16SWG SS 304 qlty. ground and polished with smooth surface and edge section. The top is designed to give a stable work surface. The table top frame is a complete assembly with front, back and two ends welded together. The sinks are made of stainless steel with inside ground and polished. Each sink is provided with a drain valve and a strainer. On the bench top, just above the sinks mixer for hot and cold water connection is provided. Overall size 2400mmL x650mm Wx900mm Ht

Washer Disinfector

Washer Disinfector, single door, suitable for cleaning and disaffection of surgical instruments, anesthetic equipment, suction bottles, cleaning buckets, general circulation goods, dental tray and glassware with a fully closed process. The washer disinfector, fully automatic, has an advanced micro-processor which controls all services, programming and statistic functions. For safety reasons the service and programming functions are coded. The door would be provided with interlocking system. The chamber is equipped with four spray arms which ensure good water penetration from all directions. Various attachments are provided to suit the load to be washed. Suitable dosage of detergent can be preset with the dosing pump. The provision of a double wall with insulation in between enables the Washer Disinfector to run with minimum sound and heat emission. The wash chamber, the inside the door, the pipework system and the circulation arms are made entirely of stainless steel. Suitable for electrical operation on 400/440 volts, 3 phase, AC supply, electrical load 13 KW. Capacity of 110 ltrs.

Stainless steel table trolley with 2 shelves

Stainless steel table trolley with 2 shelves is for use in the sterile goods store when batching sterile goods for delivery and also for short internal transport. The trolley is also suitable for use as a temporary storage or utility space at packing tables. The frame is mounted on 4nos. heavy duty swiveling castors for easy movement in narrow passages. Overall size 1080x530x800H

Spray Gun Rinser

Spray Gun Rinser with attachments is used for cleaning syringes, catheters, endoscopes, cystoscopes and variety of other instruments and articles used in sterile services.

ADMINSTRATIVE FURNITURE

Supply, Installation, all complete with followings as per technical specifications.

Public Seating Chair for WAITING AREA 3 Seater Public Place Seating Chair SS 304 with arm and backrest WITHOUT CUSHION

Public Seating Chair for WAITING AREA 2Seater Public Place Seating Chair SS 304 with arm and backrest WITHOUT CUSHION

Nursing Station 2970x 2365 Prelaminated Particle Board

Nursing Station 45mm±5mm PARTITION OF 900mmm Prelaminated Particle Board

Nursing Station 3570x 3645 Prelaminated Particle Board

Nursing Station 3455x 2540 Prelaminated Particle Board

Nursing Station 1950x2050 Prelaminated Particle Board

Nursing Station 3490x 3700 Prelaminated Particle Board

Registration Counter 2985x 3495 25 mm thick prelaminated Particle Board

Registration Counter 4545x 3015 25 mm thick prelaminated Particle Board

Chief Admin officer 1800x900x750H & Side table 1050x 450

Consultant Room & One stop room 1200x 600x 750 & side table 750x450

Technician table Chair 900x600x750H Prelaminated Particle Board & Chair

Technician table Chair 900x600x750H Prelaminated Particle Board & Chair

Dr. Anesthesia 1500x600x750H & Side table 750x 450 Prelaminated Particle Board

Seminar Room Conference Table(8 Eater) Prelaminated Particle Board

visitor Chair for Dr room/Helpdesk chair /registration counter chair & Nursing station chair Visitor Chair Executive Medium Back Visitor Chair PP Armrest, High density (polyurethane foam on Seat Nylon net fabric 600 GSM on back 3D bend hot pressed seat ply 14 mm thick CRCA pipe frame 16 gauge Good quality fabric tapestry. Colour and shade as approved by Engineer in chargeCRCA ERW round pipe(With castor & Without Castor)

Dr. Anesthesia Revolving Chair HIGH BACK CHAIR Glass filled nylon frame structure Headrest with multiple adjustments Taiwan wire mesh 4way lumber adjustment Multilock synchrotilt mechanism 3d bend hot pressed seat ply seat plastic cover high density pu foam seat cushion foam mesh on the seat 6way adjustable arm with pu pad Class 3 gas lift Telescopic cover for gas lift Glass filled nylon base and castors.

Consultant chair Revolving Chair HIGH BACK CHAIR Glass filled nylon frame structure Headrest with multiple adjustments Taiwan wire mesh 4way lumber adjustment Multilock synchrotilt mechanism 3d bend hot pressed seat ply seat plastic cover high density pu foam seat cushion foam mesh on the seat 6way adjustable arm with pu pad Class 3 gas lift Telescopic cover for gas lift Glass filled nylon base and castors.

staff chair/ Confrence room chair Revolving Chair Medium BACK CHAIR Glass filled nylon frame structure Headrest with multiple adjustments Taiwan wire mesh 4way lumber adjustment Multilock synchrotilt mechanism 3d bend hot pressed seat ply seat plastic cover high density pu foam seat cushion foam mesh on the seat 6way adjustable arm with pu pad Class 3 gas lift Telescopic cover for gas lift Glass filled nylon base and castors.

STAFF LOCKER 6 Compartment Steel Clothes Locker M.S sheet conforming to commercial quality CR- 1

DOCTOR'S LOCKER (Female) 6 Compartment Steel Clothes Locker M.S sheet conforming to commercial quality CR- 1

DOCTOR'S LOCKER (Male) 6 Compartment Steel Clothes Locker M.S sheet conforming to commercial quality CR- 1

CCB GUIDELINES HOSPITAL IQUIPMENT

Supply, Installation, all complete with followings as per technical specifications.

HYBRID (ICU /HDU- 16 Bed Unit)

Motorized ICU Bed 4 Section With Mattress

Manual Bed 4 Section with Mattress

Bedside Locker

Over Bed Table

IV Stand With SS Rod & Castor Base

Bed Side Stool

Bio Medical Waste Bin-small -Set of 3

Multi Para Monitor With Central Station

ICU Ventilator

Syringe Pump

Laryngoscope

Thermometer - Infra red Type

Ambu Bag Adult

Aneroid BP Appartus

Opthalmoscope

ECG Machine 12 Channels

Portable Ultrasound

Biphasic Defibrillator

ABG Machine With ISE

Electronics Weighing Scale - Adult

Electrical suction Apparatus

Patient stracher (Fully SS)

Wheel chair (Foldable)

Crash Cart

Dressing Trolley

Drug Trolley

ECG Machine Trolley

Instrument Trolley

Oxygen cylinder trolley

Glucometer

Stethosocope

OPERATION THETARE -1

OT Table

OT Light

Anestheisia Work station

Surgical Diathermy

Syringe Pump

Infusion Pump

Biphasic Defibrillator

Instrument Set

Laryngoscope

Ambu Bag Adult

Electical Suction Apparatus

Patient stracher (Fully SS)

Wheel chair (Foldable)

Crash Cart

Dressing Trolley

Drug Trolley

Instrument Trolley

Oxygen cylinder trolley

Mayo trolley

Glucometer

Stethosocope

MINOR OT -1

OT Table

OT Light

Syringe Pump

Dressing Trolley

EMERGENCY UNIT 5 Bed

Manual Bed 4 Section with Mattress

Bedside Locker

IV Stand With SS Rod & Castor Base

Bio Medical Waste Bin-small -Set of 3

Multi Para Monitor With Central Station

ICU Ventilator

Syringe Pump

Laryngoscope

Thermometer - Infra red Type

Ambu Bag Adult

Aneroid BP Appartus

Opthalmoscope

ECG Machine 12 Channels

Portable Monitor

Portable Ventilator

Biphasic Defibrillator

Electronics Weighing Scale - Adult

Electrical suction Apparatus

Patient stracher (Fully SS)

Wheel chair (Foldable)

Crash Cart

Dressing Trolley

Drug Trolley

ECG Machine Trolley

Instrument Trolley

Oxygen cylinder trolley

Glucometer

Stethosocope

DIALYSIS ROOM - 2 Bed

Manual Bed 4 Section with Mattress

Bedside Locker

Over Bed Table

IV Stand With SS Rod & Castor Base

Hemodialysis Machine

RO Plant System

Dialysis Reprocessor

Multi Para Monitor

Syringe Pump

Laryngoscope

Thermometer - Infra red Type

Ambu Bag Adult

Electronics Weighing Scale - Adult

Wheel chair (Foldable)

Crash Cart

Dressing Trolley

Drug Trolley

Glucometer

Stethosocope

MCH -02 Bed

Ward Bed (2 section) with mattress

Bedside Locker

IV Stand With SS Rod & Castor Base

Bio Medical Waste Bin-small -Set of 3

Instrument Trolley

Glucometer

Stethosocope

LDR - 01 Bed

LDR Bed

Foctal Doppler machine

Radiant warmer

Bedside Locker

IV Stand With SS Rod & Castor Base

Bio Medical Waste Bin-small -Set of 3

Crash Cart

Instrument Trolley

Glucometer

Stethosocope

WARD -24 Bed

Ward Bed (2 section) with mattress

Bedside Locker

IV Stand With SS Rod & Castor Base

Bio Medical Waste Bin-small -Set of 3

Pulseoximeter

Syringe Pump

Laryngoscope

Thermometer - Infra red Type

Ambu Bag Adult

Thermometer - Non contact type

Aneroid BP Appartus

Electronics Weighing Scale - Adult

Electrical suction Apparatus

Patient stracher (Fully SS)

Wheel chair (Foldable)

Crash Cart

Dressing Trolley

Drug Trolley

Instrument Trolley

Oxygen cylinder trolley

Glucometer

Stethosocope

Add 18% GST

Add 1% Labour cess 1%

JUNAID ENTERPRIES