PROVN OF CERTAIN EM AND BR WORKS FOR AFNET SERVICES AND PROVN OF RAILING AND STAIRCASE FOR RAMP 3D CAR AT 2402 SQN, 2 WING,AND SPECIAL REPAIRS TO CERTAIN SERVANT QTRS AFS PUNE UNDER GE AF LOHEGAON

Amount

Dismantling single layer Mangalore pattern tiles or similar tiles in roofing complete all as specified and directed by engr In charge

Dismantling battens exc 15cm for tiles any size incl tilting fillets complete all as specified and directed by engr In charge

Dismantling timber in fillets rails, posts, rafters, purlins etc over 40 Sqcm in section in unframed work complete all as specified and directed by engr In charge

Dismantling Asbestos Cement (Corrugated, Semi corrugated etc.) sheets in roof coverings complete all as specified and directed by engr In charge

S&F Plain galvanised mild steel sheet 0.63mm thick in ridges hips, valley gutter, drip and straight flashing etc complete all as specified and directed by Engr in charge .

S&F pre painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof vering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr in charge .

S&F pre painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr in charge .

S & F Rolled Mild Steel roof trusses(framed),trussed ,purlins ,rails and fastenings etc.,confirming to Fe 410 - S including distance pieces, cleats, etc., complete all as specified and directed by Engr in charge .

S & F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed by Engr in charge .

M & L for PCC type D2 1:4:8 (40mm graded aggregate) as mass concrete and filling of foundation/gap between sheet and wall complete all as specified and directed by Engr in charge .

M&L for rendering 20mm thick in CM (1:4) on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing and finished even and smooth without using extra cement complete all as specified and directed by Engr in charge .

M&L for rendering 20mm thick in CM (1:6) on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing and finished even and smooth without using extra cement complete all as specified and directed by Engr in charge .

Taking down cement plaster on brick/ stone wall including raking out joints, hacking for key scrubbing down with water etc. and clearing off the premises complete all as specified and directed by Engr in charge .

M & L rendering 15mm thick on surface of brick work/concrete surface in CM 1:6 and is to be finished even and smooth with out using extra cement complete all as specified and directed by Engr in charge .

M & L for 10mm thick cement plaster in CM 1:4 on fair faces of brick or concrete surfaces and finishing the surface even and smooth (without using extra cement) etc. complete all as specified and directed by Engr in charge .

M & L for preparation of new steel/iron surfaces of any description having width/girth exceeding 10cm and applying two coats of synthetic enamel paint over red oxide primer complete all as specified and directed by Engr in charge .

M & L for three coat of white wash on newly plastered of wall including necessary preparation of surface complete at any position complete all as specified and directed by Engr in charge .

Demolition of Brick/precast concrete block/Stone/boulder masonary walling built in cement mortar including all quoins, arches , pillars etc complete all as specified and directed by Engr in charge .

M&L random rubble stone masonary well bonded bedded solidily hearted in CM 1:4 complete all as specified and directed by Engr in charge .

All as per item No 19 above but except stones.

M&L for precast solid cement concrete block masonry exc 10cm in width built with solid blocks Grade C1 (1:3:6 mix) 20mm graded aggregate and set in CM (1:6) complete all as specified and directed by Engr in charge .

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M & L cement concrete type B0 1:2:4 (12.5 mm graded agg) 25mm thick as in sub floors complete all as specified and directed by Engr in charge .

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm in floors {Superior/Premium quality}, set and jointed in neat cement slurry and pointed in colour cement to match the shade of tile over and including 15 mm thick screed bed in CM (1: 6) complete all as specified and directed by Engr in charge .

M&L Glazed Ceramic Coloured Tiles, 350X250X7mm/300x200x7mm thick in size, set on Vertical Surfaces such as Skirting, Dado, etc,over and including 10mm thick rendering in cement mortar 1:3 Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the shade of the Tiles, complete all as specified and directed by Engr in charge .

Demolition and breaking up drain pipes (Salt glazed ware /PVC/ AC or Reinforced concrete) set in cement mortar complete all as specified and directed by Engr in charge .

S&F 75mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors or wall complete all as specified and directed by Engr in charge .

All as per item No 27 above but 110mm dia

M&L for PVC (SWR) bends of any radius with oval and access door of 75mm dia complete all as specified and directed by Engr in charge .

All as per item No 29 above but 110mm dia

S &F PVC (SWR) cowls of 75mm dia

S & F PVC (SWR) reducers 75mm dia

S &F 110mm PVC (SWR) junction single (Single T) equal or unequal with acess door complete all as specified and directed by Engr in charge .

S &F 75mm PVC (SWR) junction single (Single T) equal or unequal with acess door complete all as specified and directed by Engr in charge .

S&F in repair PVC (SWR) Nahani trap with grating of diameter of outlet 75mm including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed by Engr in charge .

S&F in repair vitreous china, squatting pan of 'Orissa' pattern, long pan, size 580 mm x 440 mm, white, with 'P' of 'S' Trap, front or back inlet and foot rests any pattern, including concrete bedding and PVC low level flushing cistern 10 Ltr capacity including 32mm PVC flush pipe, all internal fitting, inlet, outlet pipe connections etc. complete all as specified and directed by Engr in charge .

Demolition of cement concrete in ground floors and paving's n.exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engr in charge .

M&L for 100 mm thick cement concrete Type B-2, 1:2:4 (using 20mm graded stone aggregate), as in floors, etc, and finished the cement concrete surfaces even and smooth with out using extra cement, complete all as specified and directed by Engr in charge .

M&L for 75mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate as in sub base of floor and path, plinth protection etc.and finished the cement concrete surfaces even and smooth with out using extra cement complete all as specified and directed by Engr in charge .

Taking down chowkat with shutter without taking out shutter from the frame exc 1.5 and n.exc 4 Sqm each complete all as specified and directed by Engr in charge .

Supply and fix for factory made solid Panel PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded Prelaminated PVC sheet on the front face and 2mm prelaminated colour PVC sheet on back face, fixed in frame at site as per specification and drawing including fittings complete all as specified and as directed.

Supply and fix for solid PVC door frame of size 50mm x 47mm, made out of 5 mm thick plain colour PVC sheet, reinforced with mild steel square tube complete all as specified and as directed.

S&F 300 mm long Aluminium sliding door bolt, plate type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed by Engr in charge .

S&F second class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed by Engr in charge .

S&F 30 mm thick second class hardwood glazed and skeleton shutters divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers and prepared to receive glass, gauze, etc., edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauze, etc complete all as specified and directed by Engr in charge .. (NOTE :- windows and ventilator are provided with stiles and rails as specified in SSR Part -I)

S & F 30 mm thick flush shutters, solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and directed by Engr in charge .

S&F 3.0 mm thick sheet glass, ordinary quality and glazing with oil putty in squares n exc 0.5 sq mtr in each pane complete all as specified and directed by Engr in charge .

S&F in repair galvanied steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed by Engr in charge .

S & F 100 mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed by Engr in charge .

S&F 150 mm long Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed by Engr in charge .

S&F 150 mm size Aluminium handles, Extruded aluminium alloy handles, abricated type, anodised complete all as specified and directed by Engr in charge .

M&L for GI tubing 15mm dia medium grade with all fittings & fixed complete to walls & ceiling or laid in floors in repairs complete all as specified and directed by Engr in charge .

M&L for GI tubing 20mm dia medium grade with all fittings & fixtures complete laid in trenches fixed in repairs complete all as specified and directed by Engr in charge .

S&F rotational moulded polyethylene water storage tank 500 Litres capacity ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I with 20 mm ball valve high pressure PTMT with rod & high density plastic ball complete all as specified and directed by Engineer-in-Charge.

S & F in repair PVC low level flushing system plastic valve with inlet ball valve float chain and ball (of capacity 10 liters) ISI Marked incl 32mm PVC flush pipe complete all as specified and directed by Engr in charge .

S/F in repair 15mm dia bib taps, cast copper alloy with crutch or butterfly handle,screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engr in charge .

S/F in repair stop valve cast copper alloyof 15mm bore size scrwed down high pressure with crutch or butterfly handle scrwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed complete all as specified and directed by Engr in charge .

Dismantling wall/floor and ceiling boards (fiber, pulp, inlsulation, blankets) any thickness including covered fillets and supporting members complete all as specified and directed by Engr in charge .

M&L GI frame work for seamless ceiling & wall lining/ comprising of GI perimetre channel 0.55mm thick with two unequal flanges of 20 and 30mm and webof 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre /intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fastners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having Kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre in ceiling anr wall cladding complete all as specified and directed by Engr in charge .

M&L 6mm Aluminium composit fire resistance panells(ACP Sheets) of any colour inclusive of solvent cement and fixing at site on GI or Aluminium frames in wall panelling, ceiling , Pannels for Doors and Partitions as per specification and drawing complete all as specified and directed by Engr in charge . Note: Contractor is bound to submit 'Fire Resistence Certificate' for minimum two hours in respect of Aluminium composit fire resistance panells(ACP Sheets).

M&L for 5 mm thick rendering on unfair faces of ceiling , finished even and smooth without using extra cement in cement mortar 1:3 complete all as specified and directed by Engr in charge .

M&L for preperation of new concrete /plastered surface of any description, two coat of destemper oil emulsion over a coat of primer complete all as specified and as directed complete all as specified and directed by Engr in charge .

M&L for preperation of new concrete /plastered ceiling surface of any description,applaying three coat of white wash complete all as specified and directed by Engr in charge .

Demolition of Cement concrete in ground floor and pavings n'exc 15cm thickness (below or above ground level) complete all as specified and directed by Engr in charge .

M&L PCC 1:2:4, 25 mm thick type B0 using 12.5mm graded stone aggregate as in floor finished even and fair with out using extra cement complete all as directed by Engr-in-charge.

M&L for 3.2 mmLinoleum ,plaincolured in floors sealed down with an approved adhesive including stretching, cutting and fitting complete all as specified and directed by Engr in charge .

M&L Framed work such as grills,Barred iron doors,Ladders, walk ways,frame work of water tanks and similar work conforming to Fe.290.Gde-E-165 ' complete all as specified and directed by Engr in charge .

S & F Plates (Plain or Corrugated) channeis,square cut or notched (ordinary or counter sunk) forming holes with out any attachment conforming to FE-410 - W(grade E-250) quality 'A' complete all as specified and directed by Engr in charge .

Mild steel screw bolts of ength of bolt exc 5cm but n exc 10cm long, diameter of neck 11 to 15mm (machine made) with hexagonal or square heads,at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long complete all as specified and directed by Engr in charge .

M&L for Forming mortice holes exc 50 but n exc 100 Cu cm for , fixing bolts lusters,newels,rag-bolts,etc and grouting with cement mortar 1:2.' complete all as specified and directed by Engr in charge .

M & L for preparation of new steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer. complete all as specified and directed by Engr in charge .

Excavating in post holes (or similar holes) each n exc. 0.50cum getting out, returning, filling and well raming earth or broken rubble mixed with earth around etc in soft soil.' complete all as specified and directed by Engr in charge .

Preparation of new steel surfaced of any descripation exc 10 cm in width or girth and applying 2 coats of synthetic enamel paint over coat of red oxide primer complete all as specified and directed by Engr in charge .

M&L Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in hard/ dense soil complete all as specified and directed by Engr in charge .

Removing excavated soft / disintegrated Rock to a distance exc 1.5 KM from the work site , and deposited complete all as specified and directed by Engr in charge .

M&L Hardcore with boken stone of gauge n exc 63 mm, deposited, spread and levelled and layer n exc 15 cm thick, water and rolled /rammed to a true surface complete all as specified and directed by Engr in charge .

M & L for 75 mm PCC 1:3:6 type C-2 as plinth protection finished even and smooth with out using extra cement complete all as specified and directed by Engr in charge .

M&L Forming Contraction (Dummy) joints 75 mm deep x 10mm wide for plinth protection & similar work , filled with sealing compound Grade 'B' in plinth protection complete all as specified and directed by Engr in charge .

Roughening surfaces of old concretefloor by picking, sweeping clean and washing down with water to removedust, etc.complete all as specified and directed by Engr in charge .

Providing, cement concrete type B0 1:2:4 (20mm graded aggregate) as in coping kneelers, apex stones, bed plates, kerbs as directed

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm of hard/dense soil

M&L PCC 1:2:4 type B2 using 40mm graded crushed stone aggregate as in foundation filling and mass concrete complete all as specified and directed by Engr in charge .

Removing excavated soil n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed by Engr in charge .

Preparation of new plaster surface of wall and applying two coats of camouflage pattern Premium Acrylic Smooth exterior paint with Silicone additives of required shade@ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete all as specified and directed by Engr in charge .

S & F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square not, exc 5cm but n exc 10 cm long with 5 to 10 mm dia neck complete all as specified and directed by Engr in charge .

S&F for Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated). conforming to Fe-410-W (Gde-E-250) quality A complete all as specified and directed by Engr in charge .

S&F for steel work in tubular strusses incl spl shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1979 Grade ST-240 complete all as specified and directed by Engr in charge .

S&F for mild steel plate (plain or Chequired) conforming to Fe-410-W (Gde-E-250) quality B channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachement.

S & F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by Engr in charge .

Preparation of new surfaces of steel and applyingtwo coat of camouflage pattern synthetic enamel paintover one coat of redoxide to steel surfaces of any description not otherwise described over 10 cm width or girth complete all as specified and directed.

Taking down the existing surface batten type point wiring of aluminium for Light, fan, Sockets, power sockets, stair case light point complete with switch socket regulator , bracket fitting etc and making good disturbed surfaces for wall, floors etc as directed by Engr- in charge. including sorting out serviceable and unserviceable light fitting and keep serviceable fitting in safe guard for reuse as required on site.

Taking down the sub main wiring of any dia / sq mm on teak wood batten / PVC conduit GI earth wire all as directed.

Material and labour for providing point wiring with two runs of 1.5 Sqmm multi stranded copper conductor FRLS PVC insulated single core 1100 volts grade & with one run of 1.5 Sqmm single core multi stranded copper conductor FRLS PVC insulated 1100 Volts grade wire for continuous earthing complete in and including PVC casing and caping/conduit with PVC modular switch boxall fittings/fixture etc for housing switches / sockets all a specified and directed.

One light point controlled by one switch.

One 3 pin socket 5 A on independent board.

One 3 pin socket 5 A on same board.

Material and labour for providing point wiring with two runs of 2.5 Sqmm multi stranded copper conductor FRLS PVC insulated single core 1100 volts grade & with one run of 1.5 Sqmm single core copper stranded FRLS PVC insulated 1100 volts grade wire for continuous earthing complete in and including PVC casing and caping, ISI Marked complet for housing one 15 A Switch / sockets , complete all as specified and directed by Engr in charge . Note : Metal sunken box , cover plate and frame etc will be measured and paid seprately in respective item.

S & F Sub Main Wiring with FRLS PVC Insulated multistranded copper conductor wires of size 2x4.0 sq. mm + 1x2.5.0 sq. mm earth wire in casing caping complete all as specified and directed by Engr in charge .

S&F sheet metal enclosure with socket plug top , single pole and neutral enclosure with two pin earth plug and socket complete with one MCB SP of capacity 20 Amps.including fixing concealed in wall and making good the disturbed surface complete all as specified and directed by Engr in charge .

Supply and fix Energy efficient recess mounted LED panel fitting 36 Watt suitable for 2x2 grid in white colour with high quality diffuser for uniform light & high Efficiency. Made from CRCA sheet, Pre-coated white color. Separate replaceable electronic driver, lumen constant of 5700/6500K colour temperature with current electronic connections as directed complete all as specified and directed by Engr in charge .

S&F MCB SP 240 volt 6 to 32 A 'C' series complete

Supply and fix Modular switch 1 way 6A, 1 module

Supply and fix modular Socket, 6A - 2/3 pin combined 2 moduler

Supply and fix Modular switch 1 way 16A, 1 module

Supply and fix modolar Socket 6A/16A - 2/3 pin combined 2 module,

Supply and fix ceiling rose surface type bakelite/PVC three terminal 65x50mm

S & F Modular white cover plate with frame 2 Module

S & F Modular white cover plate with frame 3 Module

S & F Modular white cover plate with frame 4 Module

S & F Modular white cover plate with frame 6 Module

Taking out existing split type air conditioners of any type and capacity removing from the site and keeping it in a safe custody for re-use or deposit in store complete all as specified and directed by Engr in charge .

Fixing only split type air conditioners of any type and capacity including core cutting for passing copper tubing , drain pipe & cable through stone masonry wall with connected accessories such as bracket, including additional copper tubing with insulation, cable from indoor to out door unit and drain water pipe etc. as per site requirement complete all as specified and directed by Engr in charge .

S& F LT Panel Board along with MCCB 250 Amps as incomer & out Going 200 Amps 25 KA - 1 No, 100 Amps 25 Ka - 1 No, MCB TPN 40 AMps - 1 No, MCB SPN 40 Amps - 2 No, Copper bus bar 400 Amps for 3 phase and 150 Amps for Neutral complete all as specified and directed by Engr in charge . Note - The lay out drawing of the panel shall be got approved by the contractor before panel fabrication and shall be fabricated from CPRI approved manufacturer

Supply install testing and commissioning of isolation transformer 30 KVA, three phase, 50HZ, indoor, copper winding, oil cooled class of insulation A, metallic body duly powder coated designed for input voltage range 415+5%, ratio 1:1, vector group, Dyn 11, delta-star with 01 no MCB at incomming end first filling of transformer oil of requisite dielectric strength upto level, efficiency more than 95% of seperated neutral bushing shall be brought out for earthing potential difference between neutral to earth less than one volt with all standard fitting like, adequate number of cooling radiator, lifting hooks one set, earthing terminal two nos complete testing as per BIS 9815 & 2026.

M&L for earthing complete with Galvanised Iron earth plate electrode 600x 600x 3 mm buried directly in ground with top edge of the plate not less than 1.5 mtrs below normal gound level and connected to earth test point by means of copper Strip of size 32x6 mm all as specified and shown in electric plate No 3 of MES SSR Part-I 2009 including earthwork, PCC chamber, CI cover, protection and watering pipe, funnel, mesh etc all as required at site and all as directed and including taking down of old earthing materials complete all as specified and directed by Engr in charge . Note: (1). 7.5 RM GI strip in deemed to be included in quoted rates beyond 7.5 RM strip shall be measured and paid separately (2) Rate quoted by the tenderer is deemed to include salt & Charcoal upto & above 450 mm top of Copper plate.

S & F single phase isolation transformer to be installed at input power supply of L-2 switch,via 16Amps MCB and with power earthing point specification as follows 1Ph, Capacity 1KVA, Input 230V AC ±10%,Output 230V±10%,50 Hz,cooper wire,work efficiency more than 95%,potential between earth to neutral less than 1Volt with all standard fitting as per direction of Engineer in charge

S&F wall mounted Industrial grade metal enclosure box made from 3mm thick CRCA sheet consist of following Items:- (a) Panel mounting Industrial grade socket/plug outlet 16 A,IP44 (b) SPD ,1.5kv,320A,20kA - 1 Nos (c ) MCB SP 16 A- 1 Nos

ASHUTOSH BUILDERS