PROVISION OF INDOOR PHYSICAL TRAINING SHED NEAR BLDG NO P310 AND PROVISION OF TOILET BLOCK NEAR BLDG NO P193, P317, T118 IN INFANTRY BATTALION NUMBER II OF AGE BR II UNDER GE BRICHGUNJ

Amount

M&L Surface dressing n exc 15 cm deep and getting out hard/Dense Soil

M & L Excavating over areas, n exc 1.5 m deep and getting out Hard/Dense Soil.

Excavation in trenches not exc 1.5m wide and not exc 1.5m deep and getting out in hard/dense soil

M&L Cement concrete in foundations, filling and mass concrete type D-2 1:4:8 (40mm graded aggregate)

M&L Reinforced cement concrete (design mix M-30 grade using 20mm graded aggregate) in Foundations footings, plinth beams, bases for columns, etc and mass concrete

M&L Reinforced cement concrete (design mix M-30 grade using 20mm graded aggregate) above top of footings including attached pilasters and buttresses

M&L Reinforced cement concrete (design mix M-30 grade using 20mm graded aggregate) Columns, pillars, piers, posts and struts

M&L Reinforced cement concrete (design mix M-30 grade using 20mm graded aggregate) Beams, cantilevers, bressummers, lintels over 1.5m span

M&L Reinforced cement concrete (design mix M-30 grade using 20mm graded aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm

Removing excvated soil to a distance n.exc 50 m and depositing as directed

M&L Formwork flat or curved to sides of concrete foundations, footings, bases of columns, and plinth beams and similar work vertical or to batter

M&L Formwork flat or curved to to sides of pillars, posts, struts, piers, columns and stanchions

M&L Formwork flat or curved to sides and soffits offloor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelvesincluding sup- ports, overhangs, etc. also splays between floors and beams, etc.

M&L Formwork flat or curved to Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Ditto, but 6mm to 8mm dia

M&L pre-cast cement concrete masonary in PCC 1:3:6 type C1 using 20mm graded aggregate with solid block, exceeding 10cm in width setting in CM 1:6 complete.

M&L for 40mm thick Damp proof course in cement concrete 1:2:4 type B-O to horizontal or vertical surface including necessary formwork

M&L for 15mm thick rendering in two layers of 10mm thick backing coat inCM 1:6 and 5mm thick floating coat in CM 1:4 mixed with water proofing compound on all external wall surfaces all as specified and as directed by Engg-in-Charge

M&L for 10mm thick rendering in CM 1:6 on all internal wall surfaces all as specified and as directed by Engg-in-Charge

M&L for rendering 5mm thick in CM 1:3 on soffits of RCC slabs, roof projections, soffits and sides of RCC beams, waist slab, Loft Slab, RCC shelves, Chajjas, and the like all as specified and as directed by Engg-in-Charge

M&L Filling under floors or in foundations including watering and consolidation

M&L Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 10cm thick, watered and rammed to a true surface

M&L 100mm thick PCC 1:4:8 Type D-2 as in sub base for floors.

M&L 40mm thick Cement concrete type B-1,1:2:4 (20mm gradedaggregate) as in plinth protection

M & L for Screed bed or bedding layer of mortar 20 mm thick in Cm 01:4 for laying floor finishes

M & L for Coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

M & L for Glazed ceramic tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick backing coat in Cm 1:3 all as specified and as directed by Engg-in-Charge

M& L for two coat of wheather proof exterior acrylic emulsion paint with anti fungal property over a coat of primer on newly plastered wall surfaces including preperation of surfaces etc complete all as specified and as directed. (Make Apex Ultima)

M & L for applying two coats of oil bound distemper over a coat of alkali resistant primer on newly plastered surfaces of wall including preperation of surfaces complete all as specificed and as directed

M & L for applying two coats of oil bound distemper over a coat of alkali resistant primer on newly plastered surfaces of Ceilings, soffits of RCC slabs, roof projections, soffits and sides of RCC beams, waist slab, Loft Slab, RCC shelves, Chajjas, and the like including preperation of surfaces complete all as specificed and as directed

S&F Aluminium anodised door / window / ventilator / partition frames including shutters (Two no glazed and gauzed) side hung type with out sash bar, standard aluminium grill, using standerd section incl necessary joining cleats glazing clips, rubber packing, anodise Aluminium snap beading screws, handle and locking arragment etc complete Note : Glass & fly proof mesh measured and paid seperately as supply only. & Hardwares shall be measured and paid separetely

S&F Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification & drawing.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC `C' channel having at PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 150mm long extruded aluminium alloy anodised handles fabricated type

S&F 100mm long extruded aluminium alloy anodised handles fabricated type

S& F Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) 300 mm long and fixing clips to sheet cast or extruded sections and fixing bolt or cast aluminium alloy

S&F Aluminium anodised barrel tower bolt of extruded section of size 150mm long

S&F Aluminium anodised barrel tower bolt of extruded section of size 100mm long

Supply only 4 mm thick sheet glass ordinary quality and glazing with rubber packing around the glass, in squares not exceeding 0.50 sqm in each pane complete all as specified and as directed.

S&F Aluminum anodised butt hings 75mm long extruded alluminum, alloy with galvanised mild steel hinge pin, type C-22

S&F vitreous china water closet, pedestal type, white including flush pipe, seat cover etc, including connection to drain (or out going pipe) and to flushing pipe anti syphonage pipes etc complete all as specified and as directed by Engineer-in-Charge

S & F vitreous China wash hand basin,'OVAL TYPE' 550 mm including with single tap hole CP pillar cock of 15 mm dia brass CP chain and rubber plug , waste pipe and PVC connection.

S & F for Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe)

S&F PVC low level flushing cistern,10 litres capacity, including PVC flush pipe of required length, 15 mm bore ball valve and PVC connection 300 mm and other accessories, complete all as specified and directed.

S&F 110 mm dia PVC (SWR) Pipe single socketed in any length with rubber ring joint laid in trenches/fixed on floor/walls including jointing with solvent cement all as specified and directed by Engineer -In-Charge.

M&L for UPVC 75 mm dia Nahani trap/floor trap with PVC grating complete all as specified and directed.

S&F Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms)

S & F for Soap dish, vitreous China white, approximate size 160x 160x90mm embedded in the wall

S & F for 20mm bore Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe

S & F for 15mm bore Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe conceled.

S & F 15 mm bore pillar tap cast copper alloy with capstan heads chromium plated screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipes in repairs all as specified and directed.

S & F 15 mm bore Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S & F 15 mm bore fancy type, chromium plated with long shank and cup (concealed type)e Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S & F in Brass chromium plated shower rose 125mm size with swivel joints, including fixing to steel pipe or union

S & F in PVC waste pipe, 32mm dia, for WHB, complete all as specified and as directed by Engineer-in-Charge.

S & F inPVC waste pipe, 32mm dia for urinal, complete all as specified and as directed by Engineer-in-Charge.

S & F in PVC connections 15mm size with PTMT nuts of length 600mm

M & L for water proofing treatment with the following specifications including taking down existing roof treatment of any description and cleaning with water and scrubbing and disposing off the rubbish outside the premises, complete all as specified and as per manufacturers instructions:- (i) Apply a coat of hot blown bitumen 85/25 @ 1.20 kg/sqm over a coat of bituminous primer @ 0.3 ltr per sqm. (ii) Laying APP membrane weighing 3to 4Kg/sqm, with 100mm over laps both longitudinally and transversally and overlaps shall be sealed by torch, membrane shall be taken to the parapet through fillet and shall be tucked in inside after a height of 300 mm. (iii) Apply one coat of hot blown bitumen 85/25 @ 1.2 kg/sqm over the membrane.

PCC 1:3:6, type C2 (using 40mm graded stone aggregate), concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested

M & L Salt-Glazed stone ware drain pipes, 150mm dia (internal dia) laid in trenches and jointed as specified

PCC 1:2:4, type B1, (using 20mm graded stone aggregates) for Coping and haunching concrete

Rendering in CM 1:6, 15mm thick on fair faces of block masonry , finished even and smooth using extra cement

Precast RCC 1:2:4, type B1, (using 20mm graded stone aggregate), for cover slabs

M&L RCC type B1 1:2:4 (using 20 mm aggregate) Beams, cantilevers, bressummers,lintels over 1.5m span

M&L RCC type B1 1:2:4 (using 20 mm aggregate) on Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilaster and buttresses

M & L for Pre-cast PCC block masonry type B-1 (1:2:4) with solid block and set in CM1:6

M&L rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement.

M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement.

S & F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe-410-W(Gde-E-250) quality-B

S&F mild steel flat iron 40 x 3mm as in wind tie including all necessary drilling, bolting or riveting etc., confirming to Fe 290.

S & F for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment (Fe 410-W, Gde-E250, Quality-A)

M/L for 2 coats of synthetic enamel painting over a coat of red oxide zinc chrome primer incl preparation of new or previously untreated steel surfaces of any description over 10cm width or girth.

S&F Mild steel bolts exc 12mm n' exc 20mm dia , purpose made, with hexagonal or square head one end and screwed the other, or screw both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exc 30cm long

S&F 110 mm PVC (SWR ) pipes single socketed in any length with rubber ring joints fixed to walls for rain water pipe

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F pre-painted galvalume aluminium zinc coating GI baesd plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-30 grage with approved colour, design & pattern as in footpath, park, lawn, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method unsing PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embeddding/ laying, of interlocking paver blocks in to the sand bedding layer through vibratory compation by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete

M&L for PCC 1:3:6, type C2, (Using 40 mm graded stone aggregate), 150 mm thick as in plinth protection/Sub base flooring, finishing surface fair and even, in panels & filling joints with mortar, etc., complete all as specified and directed.

M & L for two coats of oil bound distemper over on coat of alkali resistant primer including preparation of newly plastered surfaces of wall complete all as specified and as directed

M & L for point wiring complete with single core multi stranded Copper conductor FRLS cable of size 1.5 sqmm PVC insulated unsheathed 1100 volt grade in and including PVC conduit suitable size including Tee junction bends etc in wall/fixed on ceiling and PVC switch board hylem sheet of 3mm thick including M.S Sunken boards of suitable size for housing switched sockets etc including 1.5sqmm green PVC insulated wire complete all as specified and as directed (a) One light point controlled by one way switch

(b) One ceiling fan point controlled by one way switch

(c) One three pin 5 Amp switch socket cum on same board

(d) One three pin 5 Amp switch socket cum on Independent board

Supply and fix of switch piano flush type single pole one way 5 Amp all as specified and directed.

S & F switch socket combination 2 in 1, 5 Amps, 5 pin multipurpose, flush type, 230 Volts Make: Anchor/ Leader/ Maru

Supply and fix ceiling rose surface baklite 65 x 50 mm 3 terminal, complete all as specfified and as directed by Engineer-in-Charge

Supply and fix fan speed regulator, electronic suitable for single phase AC, 240 volts, 50 Hz,100 watts, complete all as specified and as directed by Engineer-in-Charge

Supply and fix ceiling fan suitable for working on AC 230 volts, 50 Hz,1200 mm sweep 5 star rating with down rod and canopy colour of milky white including suitable fan hook anchor flashner for fixing of fan on ceiling complete all as specified and as directed.

Supply and fix energy efficient LED Smart bright batten 22 watt fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core shethed cable from fitting to ceiling rose all as specified and as diected.

S&F Street light New genration energy saving & envoirmental friendly long life versatile pressure dia cast aluminium IP65 road way luminaire with high power LEDs 35 w as light and electronic driver complete all as per with necessary brackets (made out of 25 mm bore GI light grade pipe approx. 0.6 M long) nuts, bolts etc to be fixed as on walls complete as directed.

Supply and fix in repair metal enclosure distribution board SPN, 8 way 240 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs complete all as as specified and as directed by Engineer-in-Charge

Supply and fix MCB single pole, 240 volts, 5 to 32 Amps, all as specified and as directed.

Supply and fix MCB SPN 240 volts, 5 to 32 Amps, all as specified and as directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground ( earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Meter below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed electrical plate No. 3 of SSR part - I

S & F LED mirror light fitting 1 x 10 Watt provided with high output diffuser including high efficiency electronic driver complete with LED lamp, prewired upto connection block and connecting with three core PVC copper flexible cable of size 1.5 Sq.mm from ceiling rose to connector block, including taking down old unserviceable mirror light fitting of any wattage, complete all as specified and directed by Engineer-in-Charge.

Supply and fix exhaust fan steel body suitable for on working of AC 230 V ,50 Hz 300 mm sweep 1400 RPM,with heavy duty motor ,incl louvers complete all as specified

Supply and fix in repair metal enclosure distribution board SPN, 4 way 240 volts, with 100 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs complete all as as specified and as directed by Engineer-in-Charge

Supply & lay cable protection pipe of HDPE double wall corrugated (DWC) incl couplers,bends etc of size 50 mm OD and ID 38mm confirming to IS 14930 -II and ISI Marked all specified and directed.

S&F tube light grade galvanised with all fittings laid in trenches of following size. (a) 50 mm bore.

Material and Labour for cutting bituminous road at a width not more than 30cm and a depth not exceeding 60 cm for laying of pipes on road crossing for cable protection and making good with cement concrete 1:2:4, type, B-2 to match the existing surfaces of the road all as specified and as directed by Engineer in charge.

Supply, lay, test and commissioning under ground XLPE insulated and PVC sheathed, armoured heavy duty under ground cable, suitable for earthed system, laying in trenches/duct sleeving through pipe in duct, ISI marked with aluminium stranded conductor 1100 volt grade of cross section area 2 Core 10 sq mm.

Supply and fix 25 mm bore GI tubing medium grade laid in trenches / floor or fixed to wall in any length with screwed and socket joints together with all galvanised GI fitting such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc and pressure testing, washing out complete all as specified and directed

Supply and fix 25 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed, complete all as specified and as directed

M&L for cutting existing 40mm GI line and making branch connection of 25 mm dia GI line including fittings required for connection complete all as specified and directed

Supply and fix 25 mm bore Gun Metal gate valve with iron wheel head ISI Marked screwed both ends suitable for GI tubing complete all as specifed and directed

Supplying, hoisting and fixing rotational moulded polythylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of 1000 Litre capacity etc complete all as specified and directed.

CHANDER SEKER ENTERPRISE

DEEPAK AGENCIES

M/s Saina Enterprises

SKV Engineering

M/s Kamal Electrical

LOOK UP ENTERPRISES

M/s K Moorthi