SPECIAL REPAIR TO CERTAIN LIVING-IN-ACCN INCLUDING MESSES AT VAYUSENABAD (PH-I) AT 7 BRD, AF

Amount

Taking down Cement plaster including raking out joints hacking for key scrubbing down with water etc. complete all as specified and directed by Engr-in-charge.

M&L for Rendering 10mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for Rendering 15mm thick in cement mortar in (1:4) in two layers with backing coat 10 mm thick and second coat 5 mm thick with WPC on fare face of brick work or concrete surfaces even and smooth without using extra cement complete all as specified and directed by Engr-in-charge. Note: WPC shall be measured and paid separately.

M&L for Rendering 5mm thick in cement mortar in (1:3) on ceiling even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for preparing new surfaces of walls and applying two coats of Oil bound distemper on new surface complete all as specified and directed by Engr-in-charge.

All as per item No 5 above but three coats of white wash on ceiling complete all as specified and directed by Engr-in-charge.

All as per item No 5 above but two coats of cement base paint on wall complete all as specified and directed by Engr-in-charge.

Roughening the concrete surfaces by wire brushes and washing down to remove dust foreign materials etc. flushing at junction of parapets complete and removing the same to the places where directed by Engr-in-Charge.

M&L for 25m thick plain cement concrete (1:2:4) type B-0 using 12.5 mm graded stone aggregate as in roof for maintenance the uniform slope etc any thickness at any height and in any position all as specified and directed by Engr-in-charge at site.

M&L for 15mm thick cement plaster in cement mortar (1:4) with a mixture of water proofing compound @ 3 % by weight of cement on dried concrete surface finished fair and even without using extra cement complete all as specified and directed by Engr-in-charge. Note:- Water Proofing Compound shall be measured separately.

Supply only integral water proofing compound complete all as specified and directed by Engr-in-charge.

M&L for preparation of roof surface thoroughly wire brushed washed, dried up and cleaned of all foreign matter and dust to receive primer, On the dried roof surface one coat of approved bitumen primer @ 0.25 to 0.30 ltrs per Sqm shall be applied, On primed surface the polymerized modified bituminous water proofing membrane with non woven polyester APP membrane having weight @ 3 Kg/Sqm & minimum thickness 3mm shall be laid by torch application method, the overlap while torching shall be 100mm on length side & 100mm on width side of membrane as per manufacture instructions, finishing of top surfaces by two coats of aluminium paint over a coat of blown bitumen 85/25 grade @ 1.20 Kg/Sqm complete all as specified and as per manufacture instructions.

M&L for cutting out cracks to V-section in existing roofs or terracing cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand in cement mortar (1:1) by weight complete all as specified and directed by Engr-in-charge.

M&L for cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate to weathering slightly rounded or chamfered angles and throttling complete all as specified and directed by Engr-in-charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each complete all as specified and directed by Engr-in-charge.

All as per item No 15 above but exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed by Engr-in-charge.

S&F for anodised powder coated aluminium frame (minimum 50 micron powder coating) for doors, windows, ventilators with one or more rebates including cleat for fixing etc. complete all as specified and directed by Engr-in-charge.

S&F anodised aluminium powder coating of any colour (thickness or powder coating not less than 50 micron) window, ventilator shutters aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each shutter, including all fittings anodised aluminium snap beading screws etc complete all as specified and directed by Engr-in-charge.

S&F anodised aluminium powder coating of any colour (thickness or powder coating not less than 50 micron) door shutters aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, including all fittings hinges, anodised aluminium snap beading screws etc complete all as specified and directed by Engr-in-charge.

S&F 5.5 mm thick sheet glass doors ordinary quality and glazing with rubber beading in square exceeding 0.50 Sqm in each pane complete all as specified and directed by Engr-in-charge.

S&F 4 mm thick sheet glass for window/ventilators ordinary quality and glazing with rubber beading in square exceeding 0.50 Sqm in each pane complete all as specified and directed by Engr-in-charge.

S&F aluminium extruded section body door closer hydraulically regulated designation No.3 universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed by Engr-in-charge.

S&F for solid PVC door frame of Size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced complete all as specified and directed by Engr-in-charge.

S&F of factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strips of 20mm width stuck inside with solvent cement for style and plain colour PVC sheet for top rail, bottom, lock rails on either side and as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet, beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing complete all as specified and directed by Engr-in-charge.

S&F for stainless steel butt hinges with stainless steel pins 100mm size complete all as specified and directed by Engr-in-charge.

S&F for aluminium anodised barrel tower bolts of extracted section of size 150mm length complete all as specified and directed by Engr-in-charge.

S&F for 150mm extruded aluminium alloy handles, fabricated type anodized complete all as specified and directed by Engr-in-charge.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed by Engr-in-charge.

M&L for false ceiling with anodised aluminium grid snap of size 605mmx605mm frame hanging from slab with adjustable 3mm dia GI wire suspension with MS cleat and dash fasteners system including 12mm thick perforated particle board medium density BWR grade of size 60 cm x 60 cm in size fixed with staples on snap complete all as specified and directed by Engr-in-charge.

Dismantling stone slab and tiles of any description in any thickness floor of aprons etc. complete all as specified and directed by Engr-in-charge.

M&L for machine cut Kota stone slab flooring 20-25mm thick over cement screed base laid over 20mm screed bed in cement mortar (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engr-in-charge.

All as per item No 31 above but on vertical surfaces over 10 mm thick plastering in cement mortar (1:4) complete all as specified and directed by Engr-in-charge.

M&L for Marble work 18 to 20mm coloured (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed by Engr-in-charge.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed by Engr-in-charge.

M&L for PCC (1:3:6) type C-1 using 20mm graded stone aggregate 75mm thick as in plinth protection complete all as specified and directed by Engr-in-charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store & rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L for Glazed ceramic coloured tiles in vertical surface 350 x250x 7 mm/ 450x 350x7 mm thick set including 15mm thick screed bed in cement mortar (1:4) complete all as specified and directed by Engr-in-charge.

M&L for Non skid ceramic colour tile 7.00 to 8.00 mm thick (square/rectangular) area exceeding 0.11 Sqm and not exceeding 0.18 Sqm in floor including 15mm thick screed bed in cement mortar (1:4) complete all as specified and directed by Engr-in-charge.

M&L for light shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, Laid on Floor, over and including 15 mm thick screed bed in cement mortar (1:4) Laid and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the shade of the Tiles complete all as specified and directed by Engr-in-charge.

Ditto as per item no above but in skirting including 10mm thick back coat in cement mortar (1:3) complete all as specified and directed by Engr-in-charge.

S&F in repair of 15mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr-in-charge.

S&F in repair 15mm bore stop valve cast copper alloy screwed high pressure with crutch or butterfly handle, screwed both end for iron pipe or for union complete all as specified and directed by Engr-in-charge.

S&F in repair WHB vitreous china (580x450mm) flat back including connector, waste pipe brackets complete all as specified and directed by Engr-in-charge.

S&F in repairs of 15mm dia bib taps, cast copper alloy, with capstan heads, chromium plated complete all as specified and directed by Engr-in-charge.

S&F in repair of 110 mm PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed by Engr-in-charge.

S&F in repair of PVC (SWR) bends (TEE, Elbow & socket) any radius 110mm bore complete all as specified and directed by Engr-in-charge.

S&F in repair of 75 mm PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed by Engr-in-charge.

S&F in repair of PVC (SWR) bends (TEE, Elbow & socket) any radius 75mm bore complete all as specified and directed by Engr-in-charge.

S&F in repair of 32 mm bore waste coupling of PTMT (half or full threaded) (minimum weight 45 gms) complete all as specified and directed by Engr-in-charge.

Taking up or down steel tubing and connections 15mm bore pipe complete all as specified and directed by Engr-in-charge.

Taking up or down steel tubing and connections 20mm bore pipe complete all as specified and directed by Engr-in-charge.

S&F GI water tubing medium grade 20mm bore with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed by Engr-in-charge.

S&F GI water tubing medium grade 15mm bore with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed by Engr-in-charge.

S&F in repair 100 mm dia cast iron floor trap with grating including jointing to waste pipe in run lead fixed in concrete (1:2:4) type B-1 using 20 mm graded stone aggregate complete all as specified and directed by Engr-in-charge.

Demolition of brick / stone work built in cement mortar including all quoins, arches, pillars etc. excluding ashlar facing, dressed stonework and precast concrete articles complete all as specified and directed by Engr-in-charge.

M&L for brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engr-in-charge.

S&F in repair wash down water closet EWC with soft close seat cover and twine flush fitting 710x370x745mm complete all as specified and directed by Engr-in-charge. Make: Cera, Cat Part No S10131145 trap 100mm or equivalent

S&F in repairs Vitreous china squatting pan, Orissa pattern of size 580x440mm white, with integral foot rest (excluding flushing cistern and flush pipe) complete all as specified and directed by Engr-in-charge. Make: Cera/Parryware

S&F CI "P" or "S" trap 100 mm dia complete all as specified and directed by Engr-in-charge.

S&F in repair PVC valveless, syphonic action type, flushing cistern, 10 litre capacity, low level white, with inlet, ball valve, float and handle including brackets with all fitting complete all as specified and directed by Engr-in-charge.

S&F in repair Flush pipe of polyethylene of low or high density or PVC.32 mm dia for low level flushing cistern complete all as specified and directed by Engr-in-charge.

S&F in repair PVC connections 15 mm size with PTMT nuts if length 600mm complete all as specified and directed by Engr-in-charge. Make: Prayag/Symat

Dismantling of water tank exceeding 250 but not exceeding 500 and removing to store complete all as specified and directed by Engr-in-charge.

Dismantling of water tank exceeding 500 but not exceeding 1000 and removing to store complete all as specified and directed by Engr-in-charge.

S&F in replacement rotational moulded polyethylene water storage tank (cylinderical vertical with closed top), three layered, hoisted and fixed with position of 500 ltrs capacity including tank neeples complete all as specified and directed by Engr-in-charge.

S&F in replacement rotational moulded polyethylene water storage tank (cylenderical vertical with closed top), three layered, hoisted and fixed with position of 1000 ltrs capacity including tank nipples all fittings complete all as specified and directed by Engr-in-charge.

S&F of framed work such as grills gratings, etc with ends of bars shouldered and or riveted or forged into spikes, framed guard bars barred iron doors ladders framed balusters walk way railing framework of Fe-410-0 or Fe-310-0 complete all as specified and directed by Engr-in-charge.

S&F Welded steel wire fabric supplied and fixed complete to wood or steel members not exceeding 4 Kg per Sqm complete all as specified and directed by Engr-in-charge.

M&L for preparing of new steel surfaces of applying two coats of synthetic enamel paint over one coat of red oxide any description, over 10cm in width or girth not otherwise described complete all as specified and directed by Engr-in-charge.

Dismantling asbestos cement corrugated/sami corrugated sheets in roof covering complete all as specified and directed by Engr-in-charge.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-charge.

S&F in replacement of stainless steel kitchen stand/kitchen rack brand classical kitchenware size 30x42 (rbj) complete all as specified and directed by Engr-in-charge.

S&F in replacement of sinks of (three tier) made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm each bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engr-in-charge.

S&F in replacement of stainless steel (SS 304) grease trap with perforated basket receptacle containing three compartment system the receptacle is designed to intercept or trap of Size 90cmx 45cm x 45cm complete all as specified and directed by Engr-in-charge.

M&L for cement concrete (1:2:4) type B-0 using 12.5 mm graded stone aggregate, 40mm thick in surface channel finishing surface even and smooth etc complete all as specified and directed by Engr-in-charge.

S&F in repair to modern design mirror to bathroom size 120 cm length, 90 cm in length 12 cm, thick to fix to wall complete all as specified and directed by Engr-in-charge.

akenterprises