WELCOME MAINTENANCE UNDER AGE BR-II AND CERTAIN REPAIR TO DRAIN CULVERT FENCING AND HARDSTANDING UNDER AGE BR-I AT AMRITSAR CANTT

Amount

WELCOME MAINTENANCE UNDER AGE BR-II Taking down shutter and removing from site of any description size but exc 1 sqm and n.exc 2 sqm ; Complete all as specified and directed by Engineer-in-charge.

Taking down chowkhats or frame without taking of shutter and removing from site exc 1.5sqm but not exceeding 4 sqm each ; Complete all as specified and directed by Engineer-in-charge.

Taking down chowkhats or frame (w/o taking off shutters) and removing from site n.exc 1.5sqm each ; Complete all as specified and directed by Engineer-in-charge.

Taking down shutters of any description exc 1.00 sqm & nexc 2sqm each. and refixing in the same opening ; Complete all as specified and directed by Engineer-in-charge.

Taking down cement plaster from wall's/ceiling including raking out joints hacking for key scrubbing down with water and dispose off debries upto distance n exc 500 metre where directed ; Complete all as specified and directed by Engineer-in-charge.

Demolition of cement concrete (un-reinforced)in ground floor and paving n. exc 15 cm thick below or above ground level & dispose off debris upto a distance n. exc. 50 mtrs where directed ; Complete all as specified and directed by Engineer-in-charge.

Demolation of RCC in any position not otherwise specifically provided ; Complete all as specified and directed by Engineer-in-charge.

Material and labour PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in hold fast block, roof kerbs or mud stop, coping, rounded or chamfered on edges and like including weathering, slightly rounded or chamfered angles and throating etc incuding necessary form work ; Complete all as specified and directed by Engineer-in-charge.

Demolition of brick work built in cement mortar, seperation, cleaning and stacking of serviceable bricks for reuse and removal of debris,rubbish to a distance exc 400 m but not exc 500m ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for brick work with sub Class 'B' old size bricks, straight or curved on plan exceeding 6 Metre mean radius, built in cement mortar 1:6 ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for brick work but except brick, built in cement mortar 1:6 ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for 15mm thick cement plaster in CM (1:6) on fair faces of brick or concrete surfaces and finishing the surface even and smooth (without using extra cement) etc. ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for 10 mm thick cement plaster in CM (1:3) on concrete surfaces of ceiling and finishing the surface even and smooth (without using extra cement) etc ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for preparation of new plastered surfaces and applying two coats of oil bound distemper on walls ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for preparation of new plastered surfaces and applying three coats of white wash on ceiling ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing for Factory made single extructed WPC but frame size 65x 125 mm (wood polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), Calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kilograms/cum,screw withdrawel strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2,modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being teRunning Metreite/ borer proof,water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing for Factory made single extructed WPC (wood polymer Composite) solid Plain flush door shutters of 35 mm thick comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), Calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minumum dencity of 650 Kilograms/ cum and screw withdrawa strenth of 1800 N (Face )&900 N (Edge), minimum compressive strength of 50 N/mm2,modules of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being teRunning Metreite/ borer proof,water/moisture proof and fire retardant and fixed with steelness steel butt hinges of requred size with necessary full body threank SS screw all as direction of engr in charge ( steelness srew and butt hinges and necessary SS Screw shall be paid separatly) ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Providing and fixing powder coated(Min thickness of powder coating shall be 50 micron) aluminum windows shutter of size min 18mmx50mm for sliding type windows of standard tubular sections of approved make having glazed panels or glazed and gauzed panels of appropriate size running on seperate tracks in the channel conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth,rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. All the panels shall be of appropriate size having overlaps as required and including all required beadings, clips, rollers, rubber gaskets, cleats, etc. complete and powder coating in approved shade and colour ; Complete all as specified and directed by Engineer-in-charge. Note:- Each panel shall be measured separetely. Glass pane and wire mesh shall be measured and paid separetely.

Supply and Fixing 4 levers brass, Mortice lock, vertical type, size 100 mm ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing 30 mm thick flush shutter, soild core construction with block board core and plywood face panels commercial type on both side ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 35 mm thick 2nd class hard wood glazed and skeleton shutter’s open rebated prepare to receive glass gauge etc edges of framing plain chamfered or rounded fitted with Cut and mitered bead’s for securing glass gauge etc size of mamber of shutters as per SSR Part-I Section-8 clause 8.2 (a) ; ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for 18mm thick PVC board in cup board shelve as in kitchen ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing solid PVC 5mm thick plain colour PVC sheet in strips as in back side of kitchen cabinet , ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for 20 mm thick pvc shutter, printed one side with one coting of ultra violet chemical, glossymat finish inc 100% teRunning Metreite/water proof, fireretrandenteco friendly. Weight not less than 12 Kilograms per sqm incl Steel piano hinges, steel catcher,aluminium handle100 mm long ,aluminium hasp & stapple in repairs complete all as specified ( shade / design / size as approved by Enginner -in-Charge) ; Complete all as specified and directed by Engineer-in-charge.

Hacking out old broken glass any thickness, size, quality or description from steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing 3mm thick ordinary sheet glass and glazing with oil putty or fixed on steel frame, in squares not exc 0.50 Sqm in each panes ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repairs stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing for 300 mm size, aluminium alloy,anodized sliding door bolt, clip type, and fixing clips of sheets or extruded section and fixing of bolts and sliding bolts of extruded section fixed with stainless steel screw ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing for butt hinges of 100mm size medium weight cold rolled mild steel fixed with stainless steel screw ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs for 150 mm size aluminium anodized barrel tower bolt of extruded section fixed with stainless steel screw ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing for 200 mm size extruded aluminium anodized tower bolt of extruded section ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repairs 300mm mild steel ordinary rat tail rod pattern spring including roller plate including fixing with nailsd/ bolts or welded ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs for 150 mm size extruded aluminium anodized handle cast type fixed with stainless steel screw ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs for 125 mm size extruded aluminium anodized handle cast type fixed with stainless steel screw ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in reapair for 25mm dia stainless steel Curtain rods/ rails, with brackets, stops, rollers, finials, 1 pair of decorative knobs for each curtain rod etc ; Complete all as specified and directed by Engineer-in-charge.

Material & Labour for Preparation of new wooden surface over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for applying two coat of synthetic enamel paint over a coat of red oxide, zinc chrome primer on steel surfaces exceeding 10 cm width or girth including preparation of new surfaces ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs for 40mm long box type stainless steel hinges spring action,fixing with shutters making it good ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box,main body with stainless steel cover,governing pivot made of brass,other parts made of mild steel heavy duty ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing floor door stopper 125mm length Coated brown aluminium alloy body fixed ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing 40mm long box type stainless steel hinges spring action , ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing stainless steel rolling drawer pull type suitable for kitchen cabinets with all fixing arrangement area of each drawer n exc 0.30 sqm of vertical face having depth 450mm to 600mm ; Complete all as specified and directed by Engineer-in-charge . Note:- Net area of front finished surface will be measured.

Supply and Fixing mild steel continuous piano hinges with 30mm width of flap bright finished ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing 75-80mm long stainless steel handle, ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing galvanized iron steel tubing medium grade 15mm bore with all fittings and fixed , ceiling or laid in floor including taking down ; Complete all as specified and directed by Engineer-in-charge.

Taking up or down steel water tubing and connections including cleaning serviceable pipe for refixing and removal of unserviceable pipe, bore of pipe 15mm ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing galvanized iron steel tubing medium grade 20 mm bore with all fittings and fixed to walls, ceiling or laid in floor including taking down ; Complete all as specified and directed by Engineer-in-charge.

Taking up or down steel water tubing and connections including cleaning serviceable pipe for refixing and removal of unserviceable pipe, bore of pipe 20mm ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing Grating round 140mm size of PTMT ( minimum weight 50gms) ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repairs PVC connection 450mm long of 15mm size with PTMT nuts on both sides ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs bib taps cast copper alloy chromium plated fancy type 15mm bore with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Angle valves, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down high pressure, screwed both ends for 15 mm bore dia iron pipe or for union, ISI marked, supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing Stop valve cast copper alloy with crutch or butter fly handle screwed both ends & screwed for iron pipe of 15mm dia fixed in repairs ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Stop valve cast copper alloy with crutch or butter fly handle screwed both ends & screwed for iron pipe of 20mm dia fixed in repairs ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repairs plastic water closet seat coloured closed pattern with flat bottom cover and mild steel chromium plated or aluminized hinging device ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs for 15mm bore stop valves, cast copper alloy, concealed type, chromium plated with long shank and cup ,screwed down,handles, screwed both ends for iron pipe or for unions and fixed ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing vitreous china squatting pan ( Orissa Pattern) size 580 x 440 mm (white), with PVC P or S trap, integral foot rest including water connection to trap and flushing pipe, flushing cistern etc complete and bedding in PCC 1:7:12 type F-2 including taking down/dismantling old unserviceable WC ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing in replacement pillar tap long body 15mm dia cast copper alloy with capstan head chromium plated fancy type, screwed down high pressure, with or without letters ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe ; Complete all as specified and directed by Engineer-in-charge.

Supply & fixing vitreous china wash down water closet pan (padestal pattern) white with flush pipe for low level flushing cistern including plastic water closet seat white with jet, closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device fixed in repairs ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing in reapir PVC Mirror bathroom cabinet with shelves fancy type of size 350x450mm including fixing arrangement ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing white PVC valve less syphonic action type low level flushing cistern of 10 ltrs capacity with inlet ball valve, float valve, push button type handle including pipe 32mm dia of PVC(Heavy duty) flush pipe including brackets and taking down/dismantling old unserviceable cistern ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs for viterous chinaware wash hand basin light colour/white of size 550x 400cm flat back or angle stay, brass chromium plated waste coupling, chain, plug, porcelain rubber stopper, brackets,32mm bore PVC waste pipe of appropriate length ilcluding taking out of old WHB & making necessary connections ; Complete all as specified and directed by Engineer-in-charge.

Dismantling water tanks Exc 250 Ltr & not exceeding 500Ltr and Supply and Fixing rotational moulded polythene, triple layers, water storage tank 500 Ltr capacity, closed top, cylindrical, hoisted and fixed in position including Supply and Fixing 20mm bore PTMT ball valve epoxy coated minium weight 210gms with aluminium rod ; Complete all as specified and directed by Engineer-in-charge.

Dismantling water tanks Exc 500 Ltr & not exceeding 1000 Ltr and Supply and Fixing rotational moulded polythene, triple layers, water storage tank1000 Ltr capacity, closed top, cylindrical, hoisted and fixed in position including Supply and Fixing 20mm bore PTMT ball valve epoxy coated minium weight 210gms with aluminium rod ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 20 mm bore dia gate valve,gun metal with iron wheel head,screwed both ends and fixed ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Opening of air lock/blockage in GI/PPR pipe line from outlet of water tank to all internal GI pipes/PPR/fittings to smooth flow of water from bib taps/showers/WHB pillar tap/stop valves complete by air pressure /water gravity pressure ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repairs stainless steel kitchen plate rack size 90cm X 90cm ,25cm deep made of 1mm stainless weight not less than 7.5 Kilograms sheet fixed to wall ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing sink with drainage board made of stain less steel 1mm thick with plugs, washers and wastes pipe including bedding in cement mortar to dwarf wall or including fixing cantilever brackets of angle iron 50x50x6mm including two coats of synthetic enamel paint over coat of primer and connecting union to pipe over all minimum size 915mm x460mm bowel size 410mm x 330mm x160mm ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs CP brass towel rail of 20mm dia and 600mm long ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs 125mm CP shower rose fancy type with CP arm ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing for 110mm PVC sanitary connection -for WC connector ; Complete all as specified and directed by Engineer-in-charge.

Dismantaling floor hearth or wall tiling incl cement mortar bedding (but not backing ) removing serviceable tiles to store and rubbish off the premises ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing glazed ceramic coloured tiles 450x300mmx6mm thick, etc. on vertical surfaces such as skirting , dados and risers to steps etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match over and including 10mm thick rendering plaster in CM 1:4 on brick surface ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Coloured/printed non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match over 15 mm thick screed bed or bedding layers in CM 1:6 ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Coloured/printed non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 11 sqm but not exceeding 0.18 sqm, in vertical surface etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match over 10mm thick cement plaster in CM 1:4 ; Complete all as specified and directed by Engineer-in-charge.

Dismantling of PVC/CI pipe of 75/100mm dia fixed with cement joint ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed to walls ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing PVC(SWR)single socketed in any length with rubber ring joint fixed with wall of 75mm ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing PVC (SWR) pipes 110mm dia bend any radius ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour PVC (SWR) gully trap 125/110mm setting and jointing with solvent cement ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 110mm bore PVC (SWR) branch piece , single, equal fitted with oval access doors ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for 100 mm thick cement concrete type B2 (1:3:6) using 40 mm graded aggregate as in sub bases finished even and fair with out using extra cement for laying floor finishes ; Complete all as specified and directed by Engineer-in-charge.

Material and labour machine pressed coloured chequered cement concrete tile ISI Marked of size 30cm x30cmx22-25mm thick over and including 15mm thick cement screed in CM 1:6 set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match the colour of tiles ; Complete all as specified and directed by Engineer-in-charge.

Material and labour forrepairs of RCC projection, chajjas, facia,bands, shelves, beams, RCC railing, balcony and similar works by dismantling of loose/ disintegrated portion RCC at any height and in any sitution floor (including provn of support, formwork and welding of reinforcement if required with wire mesh of eight 1.5 Kilograms/ sqm and dubbing/ filling with PCC (1:2:4), type B-0, using 12.5 mm graded aggregate,15 to 25 mm thick after applying cement slurry @ 3 Kilograms/sqm, finished even and smooth to desired shape and applying two coats of wheater proof emulsion paint to match with existing surfaces ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Granite (of any type) work (table rubbed and polished) 20 mm thick in steps , jambs, pillars, window cills, cooking plateforms and like in cemnet mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick rendering in CM 1:4 ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for steel framed work as in chowkhat, doors of angle or other section complete drilled for fixing sheeting with all fitting and fixture ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing in repairs CI floor trap( long nose) 75mm bore with grating including Jointing to waste pipe fixed in PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 2nd class hard wood 35mm thick plain framed panelled factory made shutter two panels with lock rail and panels of 9mm BWP commercial piy or 12mm veneered ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for 19 mm particle board medium density flat pressed single layer type or three layer type with BWR type adhesive fixed with screws to frame work as in shelves ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing framed work such as grills ,framed guard bars barred iron doors ;ladders framed balusters railings and similar work conforming to Fe 410-0or Fe 310-0 ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Mild steel bar’s 6 to 8mm dia cut to length bent to shape required including cranking bending and binding with wire (annealed) not less than 0.9mm or scouring with clips quality conforming to Fe-410 or Fe 410.0 ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for RCC (1:2:4) type B-1 using 20mm graded stone aggregate as in shelves,bases for water tanks ,roof landing etc including demolition ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing light shade vitrified ceramic tiles 10mm thick ( square/ rectangular )polished, area of each tiles not exceeding 0.36 sqm as in floor set jointed in neat cement slurry and pointed in white/colour cement to match with the colour of tiles over and including15mm thick bedding layer in cement mortar 1:6 ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing light shade vitrified ceramic tiles 10mm thick ( square/ rectangular )polished, area of each tiles not exceeding 0.36 sqm as in vertical surfaces set jointed in neat cement slurry and pointed in white/colour cement to match with the colour of tiles over and including15mm thick bedding layer in cement mortar 1:6 ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for preparation of old decorated,plastered surfaces of walls, pillars cornices by steel wire brushing, scrapping down smoke soot, moulds, moss and efforescent salts and trading oil and greasy spots of and applying Two coat of white wash on walls,pillars.cornices etc ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for preparation of old decorated plastered surfaces and applying two coat of white wash with lime on ceiling surface for even shade ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for preparation of old decorated plastered surfaces of walls, pillars cornices,scrapping down smoke soot,moulds,moss and efflorescent slats and trading oil and greasy spots and applying one coat of oil bound distemper on wall ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for preparation of old decorated plastered surfaces of walls, pillars cornices,scrapping down smoke soot,moulds,moss and efflorescent slats and trading oil and greasy spots and applying two coat of oil bound distemper on wall ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for washing ,rubbing down/complete removal of existing coloured/Textured treatment from old surfaces of walls, pillars cornices and scrapping down smoke soot, moulds, moss and efforescent salts and trading oil and greasy spots and applying Two coats of oil bound distemper with one coat primer ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for 2mm thick birla wall care putty applying on walls,pillars and cornices making the edges smooth ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Preparing old surfaces of wall and applying one coats of plastic emulsion paint ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for Preparing old surfaces of ceiing and applying one coats of plastic emulsion paint ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for one coats of synthetic enamel paint over old wooden surface including preparation of wooden surface exceeding 10cm width or girth ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for one coats of synthetic enamel paint over old steel surface including preparation of old steel surface exc 10 cm width or girth ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for demolition of wall and ceiling boards (fibre,Pulp etc) of any thickness,including cover fillets ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/inteRunning Metreediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the inteRunning Metreediate channel at 457mm centre to centre with hangers 6mm dia GI (Upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI Flat 40x3mm size 60mm long ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 12mm thick Seamless calcium silicate ceiling made out of 1800 x 1200mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25mm long self drilling and tapping screws having phillips head with under head cutter at 200mm centre to centre, including finishing the joint of face board with specially formulated jointing compound and 48mm wide fibre tape to provide seamless finish including sealing the joints wit POP and applying two coats of Oil bound distemper over a coat of primer ; Complete all as specified and directed by Engineer-in-charge. Note(Frame work for ceiling shall be measured and paid separately)

Disconnecting of existing tank of capacity 500 ltr but n.exc 1000 ltr, setting aside ( or lowering if required ) and cleaning and removing all scale and dirt, etc from tanks and from mouths of circulating pipes etc. including refixing in position with all fittings and fixtures complete and making connection ; Complete all as specified and directed by Engineer-in-charge. Note: Rate shall be included of marking of date of cleaning by synthetic Paint on Tank.

Supply and fixing in repairs centre hole mixer for wash hand basin cast copper alloy fance type with capstan head chromium plated screwed down high pressure with or without lettered Hot and Cold with long screwed shanks and fly nuts screwed for iron pipe 15mmdia ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repairs CP wall mixer four way with connecting to existing shower arrangement suitable for 15mm dia bore pipe ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repairs flushing jet chromium plated connection to existing WC including flexible pipe 15mm including all necessary fitting/ assessories ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repairs glass corner shelf 30 cm radius made of 5.5mm thick sheet glass with CP guard railing fixed to walls with bracket ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing sheet glass shelf assembly 60 cm long consisting of 5.5mm thick sheet glass shelf 12cm wide with aluminum alloy bracket and CP guard railing with double rail ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repairs CP brass towel ring of appropriate size not exc 45cm dia ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repairs CP brass soap dish fixed with screws to walls ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repairs toilet paper holder of brass chroimum plated with CP cover plate ; Complete all as specified and directed by Engineer-in-charge.

Supply and fixing aluminium strip30mm wide, 1.5mm thick thick powder coated with rubber rings to be fixed with screws on bottom of existing shutters to guard from snakes/ frogs ; Complete all as specified and directed by Engineer-in-charge.

Taking down aluminium door shutters of area exc 1 sqm but not exc 4 sqm each and replacement of necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc and refixing in the same opening including fixing to floor stopper or door closure ; Complete all as specified and directed by Engineer-in-charge.

Taking down aluminium window shutters of area not exc 1 sqm each and replacement of necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc and refixing in the same opening including fixing to floor stopper or door closure ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing powder coated aluminium frame for doors ,windows, ventilators with one or more rebates including joining cleats for fixing complete all as specified and directed by Engineer-In-Charge.( Min. thickness of powder coating 50 micron)

Supply and Fixing powder coated aluminium glazed shutter(for doors) Al-section weighing 0.55 Kilograms/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading ; Complete all as specified and directed by Engineer-in-charge. ( Min. thickness of powder coating 50 micron)

Supply and Fixing Sheet glass, 5.5mm thick ordinary quality, in squares,exceeding 0.50 sqm in each pane including rubber packing and aluminium beading with and incl solar control film 25 Micron reflective type sticked to glass panes as per instructions of manufacturer ; Complete all as specified and directed by Engineer-in-charge.

Supply and Fixing 10mm thick PVC insulation panels with EPS stuck to 1mm printed PVC sheet suitably placed in aluminium door as per specification and drawing ; Complete all as specified and directed by Engineer-in-charge.

Material and labour for 15mm thick cement plaster in CM 1:4 on fair faces of brick work and finishing the surface even and smooth (without using extra cement) etc ; Complete all as specified and directed by Engineer-in-charge.

Material and Labour for preparation of new plastered surfaces and applying two coats of cement base paint on wall ; Complete all as specified and directed by Engineer-in-charge.

DRAIN CULVERT FENCING AND HARDSTANDING UNDER AGE B/R-I Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground ; Complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Plain cement concrete (1:2:4) type B-2 using 40mm graded stone aggregate as in foundation filling as mass concrete ; Complete all as specified and as directed by Engineer-in-charge.

Supply and Fixing Post and struts in fencing including cutting top to shape as directed, drilling holes, notching for wire etc, flat iron fillets (For securing wiremesh) including all necessary drilling, boulting, or reveting etc and similar work confirming to FE-290 Gde E165 ; Complete all as specified and as directed by Engineer-in-charge.

Supply only Chain link MS Galvanised fencing any size or type ; Complete all as specified and as directed by Engineer-in-charge.

Fixing only chain link fencing including line wires , any mesh any size, and type to any type. Of standard, rails, streightning bolts etc, including provision of binding wire ; Complete all as specified and as directed by Engineer-in-charge.

Supply and Fixing 5 to 10mm dia of neck, MS Screws bolts (Machine made) with hexagonal or square heads at one end and screwed the other, each screwed end to be fitted with washers and one hexagonal or square nut, exc 10 cm but n.exc 15cm long ; Complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Mild steel 10mm dia and over round bars Fe-410 as in reinforcement cut to length bent to shape required including cranking, hooking at ends and binding with mild steel wire (annealed) not less than 0.9mm dia ; Complete all as specified and as directed by Engineer-in-charge.

Supply and Fixing in Repair Galvanised iron two strand steel barbed wire 2.24mm dia, barbed with 2mm dia barbs @ 75mm c/c spacing and straining and fixing to any type of standard rail, straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, stapples or steel pin, ; Complete all as specified and as directed by Engineer-in-charge. Note : Each line of wire to be measured.

Dismantling framed work timber scantling 40 sqcm and overin section, in any position ; Complete all as specified and as directed by Engineer-in-charge.

Supply and Fixing Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes including distance pieces , cleats etc ; Complete all as specified and as directed by Engineer-in-charge.

Supply and Fixing Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified including old AC/GI sheeting ; Complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over primed steel surfaces ; Complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Reinforced cement concrete (nominal mix) Type B-1 1:2:4 (Using 20mm Graded stone aggregate) as in Columns, pillars, piers, posts and struts etc ; Complete all as specified and as directed by Engineer-in-charge.

Material and Labour Reinforced cement concrete (nominal mix) Type B-1 1:2:4 (Using 20mm Graded stone aggregate) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete ; Complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips ; Complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips ; Complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Fair finished Square, rectangular or polygonal Form work to sides of pillars, posts, struts, columns and stanchions ; Complete all as specified and as directed by Engineer-in-charge.

Taking down cement plaster of any description on brick walls, etc including raking out joints, hacking for key scrubbing down with water etc ; Complete all as specified and as directed by Engineer-in-charge.

Dismantaling of brickwork, built in cement mortar including all quoins, arches, pillars, etc. ; Complete all as specified and as directed by Engineer-in-charge.

Material and Labour for brick work with sub class "B" bricks (old size) straight or curved on plan exc 6 m mean radius, built in CM 1:4 complete all as specified and directed

Material and Labour for brick work but except bricks (old serviceable bricks obtained from dismantaling shall be reused after necessary cleaning of mortar) , built in CM 1:4 complete all as specified and directed

Material and Labour for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 using WPC 2% of weight of cement and finishing even and smooth without using extra cement ; Complete all as specified and as directed by Engineer-in-charge. (WPC measured and paid saperatly)

Supply only integral water proofing compound ; Complete all as specified and as directed by Engineer-in-charge.

Material and Labour for preparation of new plastered surfaces and applying two coats of cement base paint of shade as approved over a coat of cement primer on wall surfaces ; Complete all as specified and as directed by Engineer-in-charge.

Material and Labour for preparation of old decorated surfaces of wall and applying two coats of cement base paint of shade as approved over a coat of cement primer on wall surfaces ; Complete all as specified and as directed by Engineer-in-charge.

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) ; Complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Hardcore of broken bricks gauge n exc 63 mm, deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface ; Complete all as specified and as directed by Engineer-in-charge.

Material and Labour for 75mm thick Cement concrete type D-2 , 1:4:8 (using 40 mm graded aggregate) as in sub base ; Complete all as specified and as directed by Engineer-in-charge.

Material and Labour for 25mm sand filling under/over floors or in foundations including watering and consolidation ; Complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Machine pressed pre-cast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment ; Complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Chequered cement concrete coloured tiles 20cmx20cmx25mm thick set over & including 20 mm thick screed in cement mortar (1:6) with neat cement and pointed in grey cement mixed with pigment to match the shade of tiles ; Complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Cement concrete (1:2:4), type B-0 using 12.5mm graded stone aggregate as in benching, kerbs, mud stop, rounded or chamfered on edges including form work ; Complete all as specified and as directed by Engineer-in-charge.

M/s. M Company

S S CONSTRUCTION COMPANY

CHARAN SINGH CONTRACTOR