SPL REPAIR TO BOREWELL PUMP MOTORS AND FILTRATION SYSTEM AT U AREA IN SUKNA MIL STN AND CERTAIN OTHER SANCTIONED WORKS IN SUKNA MIL STN UNDER GE SUKNA

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in Soft/ Loose soil complete all as specified and directed.

Excavation over areas not exceeding 1.5 M deep and getting out in Soft/ Loose Soil complete all as specified and directed.

Excavation over areas exceeding 1.5 M and not exceeding 3 M deep and getting out in Soft/ Loose Soil complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils complete all as specified and directed.

Excavating post holes or similar holes, each not exceeding 0.5 Cum, getting out in Soft/Loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc 50 m & making good surface complete all as specified and directed.

Earth filling under floors including spreading, leveling in layers n.exc 25 cm thick including well ramming and watering as required complete all as specified and as directed.

Removing Excavated soils not exc 50 M and depositing where directed at a level not exc1.5 M above the starting point complete all as specified and directed.

M&L loose filling with aggregates of gauge 80 to 150 mm in soakage pits, soakage wells using broken bricks complete all as specified and directed.

M & L for Hardcore of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc.15 cm thick, watered and rammed to a true surface using broken stone or broken boulders complete all as specified and directed.

M & L for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L PCC 1:2:4 type C-1 (using 12.5 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, filling in pressed steel door frames, benching, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and including necessary formwork complete all as specified and directed.

M&L Precast reinforced cement concrete 1:2:4, type B1 (Using 20 mm graded stone aggregate) in landings, cover slabs (for Manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4 complete all as specified and directed.

M & L for providing reinforced cement concrete 1:2:4, Type B-1, Nominal Mix using 20 mm graded stone aggregate as in foundation including rafts, footing, foundation beams, plinth beams, bases for columns, basement slabs, under-reamed piles and mass concrete complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M&L for Reinforced Cement Concrete Type B-1 1:2:4 Nominal mix (using 20 mm graded stone aggregate) as walls, basement walls, ballast walls, beams and colums in floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified and directed.

M&L for Reinforced Cement Concrete Type B-1 1:2:4 Nominal mix (using 20 mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for Reinforced Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) in chajjas complete all as specified and directed

M & L for providing Reinforced cement concrete (1:1.5:3) A-1 Nominal Mix using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5 m span and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete 1:2:4, Type B-1, Nominal Mix using 20 mm graded stone aggregate as in columns, pillars, piers, posps and struts complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M&L for RCC M-25 (Design Mix) as in foundation including rafts, footings, foundation beams, plinth beams, bases of columns etc basement slabs reamed piles and mass concrete complete all as specified and directed.

M&L for Reinforced Cement Concrete M-25 (Design Mix) as in beams, cantilevers, bressummers, lintels over 1.5 m clear span complete all as specified and directed.

M&L for Reinforced Cement Concrete M-25 (Design Mix) in columns, pillars, piers, posts and struts complete all as specified and directed.

Supply only liquid water proofing compound ISI mark.

M&L PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in gap between roof sheets and brick wall, thickness of concrete bed exc. 5 cm and not exc.10 cm thick & width not exc. width of one brick thick wall including necessary scaffolding and formwork ht up to 7m complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan n.exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks in one brick thick honey-comb wall built in cement mortar 1:4 complete all as specified and directed.

M&L for 40 mm thick Damp proof course to horizontal or vertical surfaces including necessary form work in cement concrete 1:2:4 type B-0 (Using 12.5 mm graded stone aggregate) complete all as specified and directed.

M&L for 25 mm thick Damp proof course to horizontal or vertical surfaces including necessary formwork in cement concrete 1:2:4 type B-0 with Polythene film, 150 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq. m complete all as specified and directed.

M& L for cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, lintels, shelves etc, and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good on brick walls, cutting n.exc. 10 cm in girth complete all as specified and directed.

M & L for use and waste of formwork to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beams; and similar works; in rough finished flat surface of concrete complete all as specified and directed.

Use and Waste of formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for rough finished flat formwork to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exc. 200 mm thick (horizontal or sloping) work as rough finished surfaces of concrete complete all as specified and directed.

M&L Use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges for fair finished surfaces of concrete, flat / curved complete all as specified and directed.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete complete all as specified and directed.

S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints including making rebate for fixing second shutter as per site requirement complete all as specified and directed.

S&F 30 mm thick flush door shutters solid core construction, with block board core and plywood face fanels, commercial type on both side with liping/frame to match complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

S & F 30 mm thick (style thickness) factory made solid panel PVC shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheets beading and joined together with solvent cement as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of wire gauze in lieu of plain colour PVC sheet. The wire gauze shall be wrapped on an additional square 8mm MS Solid tube and this tube shall be welded to MS tubes. The wire gauge shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F factory made Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S&F 100 mm butt hinge, medium weight, cold rolled mild steel, with screws complete all as specified and directed.

S&F 100 mm butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F Floor door stopper of Aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 150 mm complete all as specified and directed.

S&F in repairs Aluminium (extruded section body) body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width of and of weight between 61 to 80 Kg. complete all as specified and directed.

S&F in repairs Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S&F in repair 28 mm dia curtain harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc with two nos of scoket end caps and brakets (decorative type) for doors/window opening complete all as specified and directed.

S & F Mild steel work in framed work such as grills, gratings, framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; handmade sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

M&L for Mild TMT bars 6 mm to 8 mm dia., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 5 mm to 10 mm dia.,cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

S & F Joist, channel, angle, flat iron or tee sections, fixed independently, with connecting plates, etc. confirming to Fe 410 -W (Gde-250 quality A) complete all as specified and directed.

S&F rolled mild steel in plates, gusset plate (plain or chequered) channels square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe-410W (Gde-E-250) quality-A complete all as specified and directed.

S&F Roof truss (framed) trussed, purlins,crane gantires of steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1998 grade St-240 including one shop coat of zink chromate primer paint including preparation of surface including dismantling complete all as specified and directed.

S & F of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 including fabrication complete all as specified and directed.

S&F steel ventilator with top hung shutter and including hinges steel peg stay complete all as specified and directed.

S&F aluminium anodised powder coated frame work (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates and including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws etc, complete all as specified and directed.

S&F powder coated aluminium window and ventilator shutters (two / three track) sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws etc. complete all as specified and directed.

S&F pre-painted 4 mm thick E-board designer/ decorative ceiling of size 600x600mm fixed or laid / inserted to aluminium framework with screws in false ceiling (flat or sloping) of grid size 605 x 605 mm and including anodised aluminium snap grid frame work for false ceiling hanging from structural steel / scantling with 6 mm GI wire (upo 1200mm length)adjusting level fixed to roof slab by means of ceiling cleats made out of GO flat 40x3 mm size 600 mm long and expansion hold fastners 12.50 mm dia 40 mm long with and including building board complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

M&L 75 mm thick, PCC 1:3:6, type C-2 (using 20 mm graded crushed stone aggregate) as in sub base, floors, paths, plinth protection, hardstanding etc and laid fair in alternate bays and in including filler joints with sealing compound grade 'A' if required finished even and smooth without using extra cement complete all as specified and directed.

M&L 75 mm thick, PCC 1:2:4, type B-2, (using 40 mm graded crushed stone aggregate) as in plinth protection, hardstanding, floors, paths, etc, finished even and fair without using extra cement complete all as specified and directed.

M&L 100 mm thick, PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base finished even and rough complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B0 (using 12.50 mm graded stone aggregate) in floorings including finishing the surface even and fair to receive floor finishes complete all as specified and directed.

M&L 40 mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregate) as in flooring, etc, finishes concrete surfaces even and rough to receive cement screed complete all as specified and directed.

M&L Coloured glazed ceramic tiles 350x 250x 7 mm/ 450X 350X 7mm thick in vertical surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 cm thick backing with cm 1:3 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 20 mm thick in CM 1:6 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, as in skirting/dado on vertical surfaces over etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 10 mm thick in CM 1:3 complete all as specified and directed.

M&L cement concrete chequered tiles 300 x 300 x 25 mm thick as in floors, set and jointed over and including 15 mm thick screed bed in CM 1:6 and pointed in grey cement and pigments to match the colour of tile complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement using WPC compound complete all as specified and directed. Note:- WPC shall be measured and paid separately.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L preparation of new plastered wall surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty complete all as specified and directed.

M&L preparation of new plastered wall surfaces and including applying two coats of cement base paint complete all as specified and directed.

M&L for preparation of new plastered wall surfaces and including applying two coats of cement base paint over a coat of cement primer complete all as specified and directed.

S&F 4 mm thick tinted glass of any size with aluminium bedding and complete all as specified and directed.

S & F 3 mm thick Frusted glass, ordinary type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane fixed to steel frame including steel pin complete all as specified and directed.

M&L preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

S&F steel water tubing and connection medium grade 15 mm bore with all fitting fixed to wall, ceiling or laid in floors complete all as specified and directed.

S&F steel water tubing and connection medium grade 20 mm bore with all fitting fixed to wall, ceiling or laid in floors complete all as specified and directed.

S&F 80 mm bore GI tubes medium grade with all fitting and fixed complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks of 1000 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank including dismantling of old tank complete all as specified and directed.

S & F 15 mm bore bib taps, two way, fancy type chromium plated cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F 15 mm bore fancy type chromium plated bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs pillar tap 15 mm bore,fancy type, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered “hot" or “cold” with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S & F 15 mm bore angular Stop cock cast copper alloy fancy type, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F PVC connections 15 mm size with PTMT nuts, of length 450 mm & suitable for cold/hot water supply complete all as specified and directed.

S&F stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore of pipe complete all as specified and directed

S & F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S & F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S & F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F PVC (SWR) Floor trap of 75 mm outlet plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

M & L for PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150 mm bore pipe complete all as specified and directed.

M & L 150 mm dia Salt Glazed stone ware drain pipes laid in trenches and jointed in CM 1:1 complete all as specified and directed.

S&F in repairs vitreous china urinal half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

S&F vitreous china european water closet pan (pedestal pattern) white in colour with fixing bolts and flush pipe, connection to trap and to flushing cistern and all joints, including plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel CP hinges complete all as specified and directed.

S&F in repairs vitreous china wash hand basin white flat back of size not less than 550 x 400 mm with and including PVC waste pipe 32 mm bore, CP waste fitting and cutting for and pinning in ends of brackets etc, complete all as specified and directed.

S&F in repairs PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F in repairs health faucet 12 mm bore, ABS chromium plated with & including 1.0 mtr chromium plated flexible tube & wall hook and connection with angular stop cock complete all as specified and directed.

Demolition of brick work in cement motor including pillar etc below / above ground level etc and removing to a distance not ex 50 meter complete all as specified and directed.

E/M PORTION

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (medium grade) concealed in wall / ceiling with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc. including all other fixing accessories for one light / fan / exhaust fan / call bell point controlled by one 5 / 6 Amps switch and including cutting chasing (as required) and making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. Note:- (i) Making good to match with the adjoining surface shall

All as per Sl. item No. 116.00 above but for one 5 / 6 Amps socket outlet point on independent board.

All as per Sl. item No. 116.00 above but for one 16 Amps socket outlet point on independent board with 2.5 sqmm cable and 2.5 sqmm earth wire

All as per Sl. item No.116.00 above but for one 5 / 6 Amps socket outlet point on same board.

All as per Sl. item No. 116.00 above but for one light point controlled by two, 2 - way switches complete all as specified and directed

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including PVC casing caping (double lock pattern) and accessories on wall / ceiling surfaces etc. with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc including all other fixing accessories for one light / fan / exhaust fan point controlled by one 5 / 6 Amps switch including taking down wiring & connected switch / socket / regulator bell etc. complete all as specified and directed.

All as per Sl. item No. 121 above but for one 3 / 5 Amps socket outlet point on independent board.

All as per Sl. item No. 121.00 above but for one 3 / 5 Amps socket outlet point on the same board.

M & L concealed sub main wiring / circuit using with 2 runs of 2.5 sqmm main wire along with 1 run of 2.5 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- (i) Two single core wires of 6 sqmm and one wire of 6 sqmm and one run of Pvc conduit shall be measured as one unit. (ii) The unit rate included for making good the disturbed surface including finishes to match with the adjoining surfaces along with cutting chases.

M & L concealed sub main wiring with 2 runs of 2.5 sqmm main wire along with 1 run of 2.5 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

S&F switch piano flush type one way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S & F Switch piano 5 Amps single pole two way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S & F Switch Socket combination 16 Amps 3 pin flush type complete all as specified and as directed.

S & F Socket outlet 5 Amps 3 pin flush type complete all as specified and as directed.

S&F MCB SPN 40 Amp, 10 kA, 240V 'C' curve including taking down complete all as specified and as directed.

S&F MCB SP 6 to 32 Amp, 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F ceiling rose, 3 phase / PVC / polycarbonate isolated body complete all as specified and directed.

S&F stepped type electronic fan regulator two module, with 5 step, AC 50 Hz 240 Volts grade complete all as specified and directed.

S&F MCB DB, SPN 8 way, IP-43, IK 09, double door type with metal door, with 100A copper neutral and earth bus bar for fixing MCB, fixing flush to wall & making good the disturbed surfaces complete all as specified and as directed.

S&F MCB DB, SPN 8 way, IP-43, IK 09, double door type with metal door, with 100A copper neutral and earth bus bar for fixing MCB, fixing flush to wall & making good the disturbed surfaces including taking down complete all as specified and as directed.

S&F Recessed Mounted Square (2'x2') LED Panel light 36 watt with CRCA powder coated housing & high transmittance Opal diffuser for glare free with Electronic LED Driver. IP20, PF ≥0.95, System Lumens ≥120 lm/W, 5700k CRI ≥ 80, Operating Voltage range 140 V - 270 V.complete all as specified and directed.

Supply and fix LT XLPE aluminium cable of size 10 Sqmm x 2 Core complete all as specified and as directed.

S&F LED light fitting 1 x 20 watt, 220V, decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size for ceiling rose complete all as specified & directed.

S&F in repair of energy saving BLDC ceiling fan complete with all connected accessories as specified below: - Input Power: - 26 watts with full speed and reduced power consumption with reduced speed technology. Voltage: - 90-300 V AC, 50Hz, single Phase. RPM: - 340 to 375 rpm Blades: - Decorated Sweep: - 1200 mm. Air delivery: - Not less than 210 CFM Colour: - Glow white/Toast Brown/Gloss Black/or others as approved by Engr-in-Charge Speed/power control: -Without Remote through existing regulator. Star rating: - BEE 5 Star Rating Warranty: - As specified by the manufacturer, contractor shall produce original warranty and test certificate from the manufacturer.

Taking up submersible pump assembly of capacity 10 to 15 HP with and including column pipe of approximate 50 to 80 m length from borewell using chain pulley block manually, transporting to workshop and back including dismantling, taking out burnt winding wire, rewinding using super enamelled insulated copper winding wire of appropriate gauge and turn, providing insulation materials and assembling, air washing lowering complete assembly and electrically connecting complete all as specified and directed.

S&F in repairs 80 mm bore & 3 m long MS heavy duty seamless black column pipe with both ends flanged, wall thickness not less than 5.4 mm in borewell with and including all jointing materials such as nut, bolts, washers, rubber gasket etc. complete all as specified and directed.

S&F in repairs PVC insulated 6 sqmm 3 core flat submersible cable copper conductor 1100 V grade in bore hole / over the ground, connecting with motor and starter terminals complete all as specified and directed.

M&L rolled mild steel conforming to Fe-410W (Gde-E-250) quality-B in compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. & dismantling complete all as specified and directed.

M&L for Development of tube / bore well with air compressor of suitable capacity till sand / mud free water of potable quality is obtained and to achieve minimum discharge capacity of 3600 LPH / max yield complete all as specified and directed. Note:- Compressor with acessories & tubes etc. shall be arrranged by the contractor and deemed to be included with the quoted rate.

Supply, lowering, installation, testing and commissioning of submersible pump set complete with 3 phase submersible electric motor coupled with the pump having capacity 11 KW/15 HP , 7 stage or as per OEM recommended stage suitable for coloum pipe/ outlet pipe of 80mm dia fixing with existing coloumn pipe at site complete all as specified and as directed. Note: Old U/s Pump shall be deposited to MES Store.

Supply, lowering, installation, testing and commissioning of submersible pump set complete with 3 phase submersible electric motor coupled with the pump having capacity 7.5 KW/10 HP , 4 stage or as per OEM recommended stage suitable for coloum pipe/ outlet pipe of 80mm dia fixing with existing coloumn pipe at site complete all as specified and as directed. Note: Old U/s Pump shall be deposited to MES Store.

Supply, lowering, installation, testing and commissioning of submersible pump set complete with 3 phase submersible electric motor coupled with the pump having capacity 3.5 KW/5 HP , as per OEM recommended stage suitable for coloum pipe/ outlet pipe of 40mm dia fixing with existing coloumn pipe at site complete all as specified and as directed. Note: Old U/s Pump shall be deposited to MES Store.

M&L for mild steel fittings such as reducer, well cap, bail plug, strip for centering, clamps etc complete all as specified and directed.

Supplying, fixing and jointing of Cast iron NRV, ISI marked, Class PN-1.6 with flanged and drilled ends, suitable for 80mm nominal bore pipe/fittings including joints and jointing materials such as bolt, nuts, washers and rubber gasket etc complete all as specified and directed.

M&L for Opening of Iron removal filter coloumn and taking out complete filter media, and cleaning inner surface throughly for 15 cum/hr system and refilling usable filter media complete all as specified and directed

M&L for Opening of water treatment filter coloumn and taking out complete filter media, and cleaning inner surface throughly for 75 cum/hr system and refilling usable filter media complete all as specified and directed.

M&L for Opening of water treatment filter coloumn and taking out complete filter media, and cleaning inner surface throughly for 50 cum/hr system and refilling usable filter media complete all as specified and directed.

M&L Cleaning and washing thorougly any type of pebbles/ Media obtained from the IR filter complete all as specified and directed.

M&L for replacment of quartz silica sand of 32 -64 mm grade media size for DMF complete all as specified and directed.

M&L for replacment of quartz silica sand of 16 - 32 mm grade media size for DMF complete all as specified and directed

M&L for replacment of quartz silica sand of 8 - 16 mm grade media size for DMF complete all as specified and directed.

M&L for replacment of quartz silica sand of 4 - 8 mm grade media size for DMF complete all as specified and directed.

M&L for replacment Activated carbon filter media IV1000 complete all as specified and directed.

M&L for replacment Best Iron Removal media (BIRM) A8006 complete all as specified and directed.

M&L for replacment Magnese Dioxide (MnO2) complete all as specified and directed.

M&L for replacment of water softener Resin complete all as specified and directed.

M&L for strainer nozzel suitable for water treatment filter complete all as specified and directed.

M&L for CI butterfly valve 80 mm dia, stainless steel disc, gear mountable as per IS 13095 Class PN-16 complete with nuts, bolts , washers and rubber gaskets including taking out old unserviceable butterfly valve complete all as specified and directed.

All as per item No.163 above but 100 mm dia size

S&F 100 liters capacity solution preparation cum settling tank, FRP construction with lid, port hole, inlet / outlet / drain connection, sludge connection facility, level gauge etc. and fitted with & including speed reducing motor and SS-316 agitator complete all as specified and directed.

S&F Chlorine Dosing Pump 0-10 LPH capacity including connecting pipe fiting etc complete all as specified and directed.

S&F in repairs PVC insulated 10 sqmm 3 core flat submersible cable copper conductor 1100 V grade in bore hole / over the ground, connecting with motor and starter terminals complete all as specified and directed.

S&F fully automatic, star delta, motor starter with in-built single phase preventor suitable for 20 HP motor with suitable relay range including taking down complete all as specified and directed.

S&F fully automatic, star delta, centrifugal / monoblock motor starter with in-built single phase preventor suitable for 10 HP motor with suitable relay range including taking down complete all as specified and directed.

M&L for preparation of outer surface with two coat synthetic enamel painting of cylidrical shape IRF/WTP tank of capacity 15 cum/hr complete all as specified and directed.

M&L for preparation of outer surface with two coat synthetic enamel painting of cylidrical shape IRF/WTP tank of capacity 75 cum/hr complete all as specified and directed.

M&L for preparation of outer surface with two coat synthetic enamel painting of cylidrical shape IRF/WTP tank of capacity 50 cum/hr complete all as specified and directed.

M&L for preparation of outer surface with two coat synthetic enamel painting of GI/DI pipe of size 80 mm outer dia with connected fitting complete all as specified and directed.

Jagatbandhu Enterprises (BID ID -3071360)

SHIVALAYA ENTERPRISES (BID ID -3071653)

D K SARKAR (BID ID -3071402)

MS ESSCON (BID ID -3071720)

Janata Enterprises (BID ID -3071723)

G C DUTTA N CO (BID ID -3071713)

MS ORIENT ENGINEERING WORKS (BID ID -3071685)

A K ENTERPRISES (BID ID -3072030)