CREATION OF RECORDS OFFICE AT CABS BANGALORE

Amount

Demolishing R.C.C work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material by mechanical means, including loading, transporting, unloading to approved dumping ground outside MD land of any lead as per direction of Engineer - in- Charge.

Demolishing brick work manually/ by mechanical means in cement mortar including stacking of serviceable material and disposal of unserviceable materials outside MD land at any lead as per direction of Engineer-in-Charge.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions with extruded built up standard tubular sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size as in frame work and partition, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, and paneling to be paid for separately)

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators with extruded built up standard tubular sections and other sections of approved make conforming to IS: 733 and IS: 1285, including providing and fixing hinges/ pivots, providing and fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. NOTE :- Glazing, and paneling to be measured and paid for separately.

Providing and fixing glazing with float glass panes of 5 mm thickness (weight not less than 12.50 Kg/Sqm) in aluminium door shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . NOTE :- Cost of aluminium snap beading shall be paid in basic item.

Providing and fixing glazing With float glass panes of 4.0 mm thickness (weight not less than 10Kg/Sqm) in aluminium window and ventilator shutters etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. NOTE :- Cost of aluminium snap beading shall be paid in basic item.

Providing and fixing 12 mm thick prelaminated particle board with decorative lamination on one side and balancing lamination on other side, flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-Charge.

M&L reinforced cement concrete work in suspended floors, roofs having slope up to 15° landings, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

M&L centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform etc complete.

M&L steel reinforcement for R.C.C. work with Thermo-Mechanically Treated bars of grade Fe-500D or more including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Earth work in excavation in all kinds of soil by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 Sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil to approved dumping ground outside MD land.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m all as directed.

Providing and laying in position cement concrete of 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) excluding the cost of centering and shuttering - All work up to plinth level.

Providing and laying cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) in sub base of floor etc., up to floor five level, excluding the cost of centering, shuttering.

Providing and laying cement concrete 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) in coping etc., up to floor five level, excluding the cost of centering, shuttering.

Providing and laying autoclaved areated cement block masonry with 100 mm thick AAC blocks in super structure above plinth level upto floor V level in cement mortar 1:4 ( 1 cement : 4 coarse sand ) . The rates includes providing and placing in position 2 Nos 6mm dia MS bars at every third coarse of masonry work.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

M&L 15 mm thick cement plaster on the rough side of wall of mix 1:4 (1 cement: 4 fine sand) including Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

M&L for 12 mm cement plaster on the wall of mix 1:6 (1 cement: 6 fine sand) finished even and smooth with out using extra cement.

M&L finishing walls Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives with (Two or more coats applied @ 1.43 litre/ 10 Sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm) with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004.

Providing and applying wall care putty of 2 mm thickness over plastered surface to prepare the surface even and smooth and Distempering New work (two or more coats) with oil bound washable distemper of approved brand and manufacture over and including water thinnable priming coat with cement primer complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position as in gratings, frames, guard bar, ladder, railings, brackets, gates and similar worksand applying a priming coat of approved steel primer using structural steel etc as required.

Dismantling tiles of thickness 10 mm to 25 mm, in wall and floors laid in cement mortar including disposal of unserviceable material by mechanical means, including loading, transporting, unloading to approved dumping ground outside MD land of any lead as per direction of Engineer - in- charge.

M&L cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) 25 mm thick with 20 mm nominal size stone aggregate finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc complete.

Providing and laying Double charge Vitrified tiles polished finish of size 600 x 600 mm in floor (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 Kg/Sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Providing and laying Vitrified tiles of size 600x600 mm (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 Kg/Sqm including grouting the joint with white cement & matching pigments etc. complete.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, hold fasts etc., complete of area 3 sq. metres and below and stacking within 50 metres lead.

Providing and fixing pressed steel door frames of Profile B conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers, Fixing with adjustable lugs with split end tail toeach jamb as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge

Providing and fixing ISI marked flush door shutters 30 mm thick conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

M&L applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel works and painting Two or more coats on new work with synthetic enamel paint of approved tint, brand and manufacture to give an even shade.

Providing and fixing ISI marked M.S. pressed butt hinges 100x58x1.90 mm size bright finished with necessary screws etc. complete.

Providing and fixing aluminium tower bolts 150x10 mm size, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.

Providing and fixing aluminium handles 125 mm, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.

Providing and fixing aluminium sliding door bolts 250x16 mm size , ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete.

Providing and fixing aluminium hanging Twin rubber floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Renewing glass panes, with wooden fillets or aluminium window/ partition wherever necessary with float glass panes of nominal thickness 4 mm (weight not less than 10Kg/Sqm)

Dismantling C.I., asbestos or PVC rain water pipe 150 mm dia with fittings and clamps including stacking the material within 50 metres lead.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes Single socketed 160 mm diameter conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion complete all as specified.

Demolishing cement concrete of nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) manually/ by mechanical means including disposal of material including loading, transporting, unloading to approved dumping ground outside MD land of any lead as per direction of Engineer - in- charge.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size or stone aggregate 40-50mm size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Distempering Two coats with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. NOTE :- Quoted Rate includes for working Upto 20 Mtr height including all necessary scaffolding and work on walls as well as in ceiling.

M&L painting One or more coats with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade on old work of wood or steel surfaces.

Taking down carefully U/S aluminium/ copper point wiring (switch,socket fan,or power socket etc) complete with fittings such as switches, sockets, ceiling rose, light fittings etc , removing all material for reuse/ issued under sch of credit and making good the distrubed surface as the existing one, complete all as directed.

Taking down old sub main wiring of any type and size complete all as specified and directed .

Taking down MCB DB TPN/ SPN and making good to the disturbed wall of any Type complete all as specified and directed.

M&L Point wiring complete with 1.5 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS cable 1100 Volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit (minimum 20 mm dia external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR part- I, ISI marked with wall thickness not less than 1.8 mm including conduit accessories like bends, tees, junction boxes etc fixed surface/ concealed/ recessed in wall or ceiling etc including 1.5 sqmm PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity wire including modular type metal flush box with cover plate and frame of required module including modular switches complete all as specified for following :-

One light point controlled by one way switch

One Fan point/Exhaust Fan point controlled by one way switch

M & L for Sub main wiring Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawn through and including suitable PVC non matallic rigid conduit with accessories fixed on Walls / Roofs / Floors / Ceiling etc. and connecting terminal ends including One run of Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, green in colour, 1100 Volts, FRLS Grade as earth continuity conductor complete all as specified and as directed.

All as per Item No. 50 here-in-above but of size , 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire. Note: Two runs of 1.5 Sqmm copper cable,one run earth wire of 1.5 Sqmm copper cable and PVC conduit shall be measured and paid as one RM.

All as per Item No.50 here-in-above but of size ,2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire. Note: Two runs of 2.5 Sqmm copper cable,one run earth wire of 2.5 Sqmm copper cable and PVC conduit shall be measured and paid as one RM. (for 30 point x 12 Rm = 360 RM)

All as per Item No.50 here-in-above but of size , 2 X 4 sq. mm + 1 X 4 sq mm earth wire. Note: Two runs of 4.0sqmm copper cable,one run earth wire of 4.0 sqmm copper cable and PVC conduit shall be measured and paid as one RM. (for 04 Industrial socket point x 14 RM = 56 RM)

All as per Item No.50 here-in-above but of size ,4 X 10 sq. mm + 2 X 6 sq mm earth wire. Note: Four runs of 10.0 Sq mm copper cable,two run earth wire of 6.0 Sqmm copper cable and PVC conduit shall be measured and paid as one RM. (For TPN DB To TPN DB)

All as per Item No 50 here-in-above but of size , 4 X 16 sq. mm + 2 X 6 sq mm earth wire. Note: Four runs of 16.0 Sqmm copper cable,two run earth wire of 6.0 Sqmm copper cable and PVC conduit shall be measured and paid as one RM. (For Main panel To TPN DB)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 Amps modular socket outlet and 5/6 A modular switch, connections etc as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 and 15/16 Amps modular socket outlet and 15/16 A modular switch, connections etc as required. (for 15 Amp Point IB)

Supplying and fixing 3 terminal, 5A ceiling rose on the existing junction box/wooden block including connections etc as required.

Supply and fixing mudular fan regulator 220 Volt 50 Hz including modular type metal flush box with cover plate and frame of required module complete all as specified and as directed

M & L for taking down , Refixing & Painting of ceiling/ wall mounting fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust complete all as specified and as directed.

Taking down old light fittings and making good to the disturbed wall of any Type complete all as specified and directed.

Supply and fixing LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

Supply and fixing LED lights fitting Recess type 1x 40 W, 220V,AC ceiling light with high performance commercial grade solution suitable for hospital,schools,offices, and so much more (>100lm/w) with natural white connecting up with three core flexible copper conductor cable of suitable size from ceilingrose complete all as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp including bracket of suitable size with clamps, nuts and bolts etc with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Supply and fixing domestic wall mounted fan 400mm sweep , AC single phase 230/240 Volt Plastic body of speed 2050 RPM ,air delivery 90 cmm of 110 watt complete all as specified and as directed by Engr-in-charge.

Supply & fixing exhaust fans Steel body of size 300 mm sweep with AC single phase 230/ 240 V ,speed 1400 RPM with complete louver fixed in out side with making a hole as required at site with complete finishing work complete with all connections all as specified and directed by Engr-in charge.

Supply & fixing Padestal fans of size 400 mm sweep with AC single phase 230/ 240 V ,speed 1350 RPM ,Air delivery 65 CMM,Power 55 watt with complete all as specified and directed by Engr-in charge.

Supply, install,commissioning and testing of commercial Air curtain unit for prevention of dust and conditioned air losses, single phase, 220 V, 50 HZ, made out of MS/CRCA sheet of minimum thickness 18 gauge finished with two coats of red xide primer and final coat of synthetic enamel paint (oven baked) with MS -CRC 18 gauge square perforated suction grills, Aluminium alloy fans and single phase electric motor, nozzles etc, complete with fittings and accessories so as to produce 1 - 1.5 m/sec air velocity at floor level for door opening 34"x84" complete all as specified and as directed .

Supplying and fixing of 4 way (4 + 12), Double door) surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required . NOTE ;-: Vertical type MCB TPDB is normally used where 3 phase outlets are required.

Supply and fixing MCCB 4 Pole, 415 V, fixed type, of capacity 125 Amps with breaking capacity 16 KA complete all as specified and as directed.

Supplying and fixing SP 5A to 32A rating 240/415 V, 10KA 'C' curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete testing and commissioning etc as required

Supply & fix 'C' Curve MCB TPN 63/100 Amp 415 volts 10 KA rupturing capacity incl testing and commissioning complete all as specified and as directed by Engr-in-charge.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc as required.

M & L for Earthing complete with galvanised iron earth plate electrode 600x600x6mm as earthing lead buried directly in ground vertically to depth not less than 2.25 mtr below GL with the top edge of the plate not less than 1.5 mtr from GL, connected to GI earth lead of 4.0mm dia, by means of bolts & nuts,to GI and connected to earthing test point all as shown in elecrical plate No-3 of SSR part -1 of 2009 * specified or indicated and testing on completion including excavation /earth work in any type of strata PCC (1:3:6) type C1 earthing chamber pre cast slab 50 mm thick in cement concrete (1 : 2 : 4 ) type B1 , Reinforced with welded steel wire fabric (XPM) weight not less than 4 Kg/Sqm cast iron frame ,funnel with wire mesh GI watering pipe of 20 mm bore medioum grade and lugs with and including GI earth wire 4 mm dia with GI protection pipe of 15 mm medium grade 7.5 meter grade 7.5 meter long etc complete all as specified.

Supply and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing including fixing with clamps and all accessories reqd complete all as specified and as directed.

J R CONSTRUCTIONS

Lucky Enterprises

m/s raghavendra kulkarni