Provn of sentry post with guard room and toilet block near Valmiki gate in Bharatpur lines at Mil Stn Dharamshala

Amount

Excavation in trenches not exc 1.5 mtr wide and n.exc 1.5 mtr in depth for fdn etc in any type of soil, complete all as specified and directed by Engr-in-Charge

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in any type of soil, complete all as specified and directed by Engr-in-Charge.

Returning, filling, in incl spreading leveling watering and well remming in layers n.exc 25cm, complete all as specified and directed by Engr-in-Charge

Removing excavated material not exc 50mtr and depositing where directed at a level n.exc 1.5 mtr above the starting point in any type of soil, complete all as specified and directed by Engr-in-Charge

5mm thick cement plaster on fair faces of concrete surface in CM 1:3 finishes even and smooth without using extra cement including two coats of cement base paint over a coat of primer, complete all as specified and directed by Engr-in-Charge.

Cement concrete (M-7.5) PCC 1:4:8 type D-2 using 40mm graded crushed stone agg as in fdn/ sub base, complete all as specified and directed by Engr-in-Charge.

Reinforced cement concrete (M-25) design mix, 20mm crushed stone agg as in foundation, including basement slabs, footings, bases for columns, complete all as specified and directed by Engr-in-Charge.

Reinforced cement concrete (M-25)design mix, 20mm crushed stone agg as in Columns, complete all as specified and directed by Engr-in-Charge.

Reinforced cement concrete M-25 design mix(using 20mm graded aggregates) in Beams,cantilevers, lintel over 1.5m span etc, complete all as specified and directed by Engr-in-Charge.

TMT bars 10mm dia and over TMT bars, cut to length bent to shape required incl cranking bending spirally for hoping for cols, hooking and and binding with and incl mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and directed by Engr-in-Charge.

Mild steel TMT bars 6 to 8mm dia, cut ot length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engr-in-Charge.

TMT bars 5mm dia & over upto & incl 10mm dia in strups, spacer and binder, complete all as specified and directed by Engr-in-Charge.

Use and waste of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work, complete all as specified and directed by Engr-in-Charge.

Formwork to sides of pillars, posts, struts, piers,columns, and stanchions Rough finished surfaces of concrete Square, rectangular or polygonal, complete all as specified and directed by Engr-in-Charge.

Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat, complete all as specified and directed by Engr-in-Charge.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; n.exc 200m thick (Horizontal or sloping) Rough finished surfaces of concrete flat, complete all as specified and directed by Engr-in-Charge.

M & L for steel gate any type,and similar work conforming to Fe-290 Gde ,E-165 complete all as specified and directed by Engr-in-Charge.

Preparation of new steel surfaces and applying two coat of synthetic enamel paint over a coat of red oxide exc 10cm girth or width, complete all as specified and directed by Engr-in-Charge.

M & L for Brickwork with fly ash brick in CM (1:4) straight or curved on plan n.exc 6 m mean radius, complete all as specified and directed by Engr-in-Charge.

PCC 1:2:4 Type B-1 (using 20mm graded crushed stone aggregate) as in coping / benching of manholes incl weathering rounded/chamfered etc including necessary formwork / moulds, complete all as specified and directed by Engr-in-Charge.

Rendering 15mm thick cement plaster in cement mortar (1:4) on brick concrete surfaces of wall and finished even and smooth without using extra cement mixed with WPC, complete all as specified and directed by Engr-in-Charge. Note-: WPC shall be measured and paid separately

Supply only integral water proofing compound, complete all as specified and directed by Engr-in-Charge.

Extra for forming fair finishing drain or channel 30cm inner girth in cement concrete, using extra cement incl forms, moulds, mitred/stopped ends etc, complete all as specified and directed by Engr-in-Charge.

Reinforced concrete pipes of 150mm, class NP-2 laid and jointed complete with collars, complete all as specified and directed by Engr-in-Charge.

Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 for 150 mm bore of pipe, complete all as specified and directed by Engr-in-Charge.

Pre cast RCC cover 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in manhole cover slab set in cement mortar 1:4 including necessary form work , complete all as specified and directed by Engr-in-Charge.

LLDPE septic tank designed to carry sewage and sullage water, includung excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc. complete for 10 users conventional type, complete all as specified and directed by Engr-in-Charge. Make-: Sintex or equavalent as approved by AGE(I).

RCC type B1 (1:2:4) using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed by Engr-in-Charge.

Roof trusses (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, Tee, Angle channel or flat sections)ofFe-290 (Gde E-165) including distance pieces, cleats etc, complete all as specified and directed by Engr-in-Charge.

M&L for Plates (plain) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment, complete all as specified and directed by Engr-in-Charge.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm mm thick of an colour having tensile strength of 550 Mpa as in the roof covering/cladding to wall, fixed with shelf tapping screws, complete all as specified and directed by Engr-in-Charge.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in ridges, hip, valley gutter, drip and straight flasing complete all as specified and directed by Engr-in-Charge.

Brick work with fly ash bricks straight or curved on plan any radius in half bricks thick wall built in cement mortar 1:4, complete all as specified and directed by Engr-in-Charge.

Galvanised steel water tubing medium grade of size 20mm dia including short lengths with all fittings such as tees elbow sockets, bends, union, nipples, brass nut short pieces and diminishing pieces etc all as per IS 1239 fixed to walls ceiling or laid in floors, complete all as specified and directed by Engr-in-Charge.

Galvanised steel water tubing medium grade of size 15mm diawith all fittings such as tees elbows, nipples, union socket completed laid in floors wall ceiling, complete all as specified and directed by Engr-in-Charge.

Rendering 10 mm thick plaster in cement mortar 1: 6 on other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cmen, complete all as specified and directed by Engr-in-Charge.

75mm thick, PCC 1:3:6 type C1 (using 20mm graded stone aggregate) in plinth protection finished even & smooth with out using extra cement including making joints 10mm wide and 30mm deep at spacing not more than 2.5m and at corners as mandatory and filled with sealing compound grade A, complete all as specified and directed by Engr-in-Charge.

M&L for 105x 60mm pressed steel frames for door with one or more rebated incl necessary fixing longs, hinges lock strike plate etc, complete all as specified and directed by Engr-in-Charge.

M&L for 125x 60mm pressed steel frames for door with one or more rebated incl necessary fixing longs, hinges lock strike plate etc, complete all as specified and directed by Engr-in-Charge.

Factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, complete all as specified and directed by Engr-in-Charge.

Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top & bottom rails. M S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joining together with solvent cemen as per Sketch of SSR Part-II & specification, complete all as specified and directed by Engr-in-Charge.

PCC (1:3:6) type C-2 (20 mm graded aggregate) filling back of chowkats, complete all as specified and directed by Engr-in-Charge.

M&L for 35 mm thick 2nd class hard wood plain framed factory made, paneled shutter with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces .The size of rail and stile as per IS :1003(Part-I ) kiln seasoned and chemically pressure treated, complete all as specified and directed by Engr-in-Charge.

M & L for 2nd class hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); complete all as specified and directed by Engr-in-Charge.

Hard core of boulder gauge n. exc 63mm ,deposited ,spread and levelled in layers n. exc 15 cm thick,watered and rammed to true surfaces, complete all as specified and directed by Engr-in-Charge.

75mm thick cement concrete 1:4:8 type D-2 using 40mm stone aggregate as in sub base, complete all as specified and directed by Engr-in-Charge.

25mm thick PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in floor base of tiles, complete all as specified and directed by Engr-in-Charge.

Non Skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:4), complete all as specified and directed by Engr-in-Charge.

Glazed ceramic coloured tiles in vertical surfaces 450mm x 300mm x 7mm thick, set and jointed in neat cement slurry and pointed in coloured cement to match over 10 mm thick rendering in Cement mortar 1:3, complete all as specified and directed by Engr-in-Charge.

S&F Brass CP shower rose 125mm size, complete all as specified and directed by Engr-in-Charge.

Brass chromium plated tubular towel rail 20mm dia incl side brackets fixed to wall 60cm long, complete all as specified and directed by Engr-in-Charge.

Angle valve cast copper alloy chromium plated fancy type long body with capstan haed handle screwed down high pressure screwed for iron pipe or for brass ferrule of bore 15mm, complete all as specified and directed by Engr-in-Charge.

S&F Bib taps 15 mm bore, cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule fancy type chromium plated, complete all as specified and directed by Engr-in-Charge.

Soap dish,vitreous china white, 160X160X90mm, fixed to wall with plugs with chromium plated screws, complete all as specified and directed by Engr-in-Charge.

Glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets, guard and railing 60cm long, complete all as specified and directed by Engr-in-Charge.

Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, hoisted and fixed in position including connecting up pipes, complete all as specified and directed by Engr-in-Charge.

Ball brass valve 20mm dia high pressure with polythene float and fly nut complete all as specified and directed by Engr-in-Charge.

S&F Gun-metal, globe or gate valves 15mm bore, with iron wheel head, screwed both end for iron pipe, complete all as specified and directed by Engr-in-Charge.

S&F Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe, complete all as specified and directed by Engr-in-Charge.

PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement, complete all as specified and directed by Engr-in-Charge.

PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed by Engr-in-Charge.

PVC (SWR) bends any radius 110mm dia with access door, complete all as specified and directed by Engr-in-Charge.

PVC (SWR) branch piece, single T, equal or unequal 100 mm dia with access door, complete all as specified and directed by Engr-in-Charge.

Preparation of new plastered surfaces and applying three coats of white wash, complete all as specified and directed by Engr-in-Charge.

Prepration of new plaster surfaces of wall and applying two coats of cement based paint over a coat of primer, complete all as specified and directed by Engr-in-Charge.

Preparation of newly steel surface exc 10 cm width or girth and applying two coats of synethic enamel paint over a coat of red oxide primer, complete all as specified and directed by Engr-in-Charge.

Supply only 15mm pillar tap cast copper alloy with capstan heads, chromium plated screwed down high pressure, long shank and fly nuts,but fancy type , screwed with ends for iron pipe or unions, complete all as specified and directed by Engr-in-Charge.

Supply & fixing Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, white, with Cast iron ‘P’ or ‘S’ trap, front or back inlet, integral footrest complete all as specified, excluding flushing cistern and flush pipe),all as specified.

Cutting chases for concealed water tubing and making good cutting not exc. 10 cm girth in brick wall, complete all as specified and directed by Engr-in-Charge.

PVC flushing cistern 10 ltrs capacity valve less symphonic action type low level complete with in let valve handles incl brackets, polythelene flush pipe 32 mm dia complete all as specified and directed by Engr-in-Charge.

PVC connection 15 mm size with PTMT nuts of length 600 mm, complete all as specified and directed by Engr-in-Charge.

M& L for Vitreous china wash basin white 550x 450 mm excluding taps but including brackets, waste pipe and CP waste coupling, complete all as specified and directed by Engr-in-Charge.

S&F brass CP wall mixer for mixing hot & cold water screwed down for 15mm dia iron pipe and fixed, complete all as specified and directed by Engr-in-Charge.

S&F vitreous chinaware urinal half stall any size including CP connector for flushing and all fitting and fixed to walls, complete all as specified and directed by Engr-in-Charge.

Steel windows or ventilators, top hung type with glazing bars, complete all as specified and directed by Engr-in-Charge.

Aluminium, anodised, barrel tower bolts of extruded section of size 150mm, complete all as specified and directed by Engr-in-Charge.

Extruded aluminium alloy handles, 100mm in size, fabricated type, anodised, complete all as specified and directed by Engr-in-Charge.

Preparation of new wooden surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed by Engr-in-Charge.

Cutting, screwing, alterations and additions in existing GI pipe of size 40mm Ech dia including clamps, screws etc. The disturbed surfaces will be made as per existing surfaces, complete all as specified and directed by Engr-in-Charge.

M&L for point wiring with 1.5 Sqmm copper conductor (Multi-stranded) PVC insulated and unsheating FRLS electric cable 1100 volts cable and including PVC casing and caping of suitable size (as per conductor run) with all fittings/ accessories and including PVC insulated electric cable 1100 volts 1.5 Sqmm ( multi-stranded) copper conductor single core( Green colour) cable as continuous earth wire connected to common earth dolly including sunk sheet steel terminal box made out of 1.6 mm thick MS sheet covered with 3 mm thick plastic laminated sheet ( Make Hylum) concealed in wall or on surface as per site requIrement and making good disturbed surfaces of wall for one light point/bell point/fan point/exhaust fan point etc controlled by one, one way switch, complete all as specified and as directed by the Engr-in-Charge.

All as per item No 82.00 above, but for one 3 pin socket outlet 5 Amp on the same board with other switches complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 82.00 above, but for one 3 pin socket outlet 5 Amp on independent board, complete all as specified and as directed by the Engr-in-Charge.

All as per serial item No 82.00 here-in-before , but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor ( Multi-stranded) PVC insulated and unsheating electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common earth dolly, complete all as specified and as directed by Engr-in-Charge.

M&L for socket outlet 2 in 1, 3 pin, 5A flush type, complete all as specified and directed by Engr-in-Charge.

M&L for socket outlet 2 in 1, 3 pin, 5/15 Amp multipurpose, complete all as specified and directed by Engr-in-Charge.

M&L for Switch piano flush type single pole one way 15 Amp, complete all as specified and directed by Engr-in-Charge.

M&L for Switch piano flush button 5 Amps, complete all as specified and directed by Engr-in-Charge.

M&L for ceiling rose surface type, 65 mm x 50 mm two to three terminals / PVC / polycarbonate, isolated body fixed on PVC block, complete all specified and as directed by the Engr-in-Charge.

Supply & fix Sheet metal enclosure for DB’s suitable for MCBs of single pole and neutral 8 way (Double door) with 200 amp 240 Volts rated bus bar, complete all as specified and directed by Engr-in-Charge. Note: i) Connections of MCB's shall be done with appropriate size of brass/Copper thimble. ii) The disturbed surface shall be match with existing surface.

MCB SPN 40Amp breaking capacity 10 KA, complete all as specified and directed by Engr-in-Charge.

MCB SP (ISI Marked) 6 to 32 Amps 10 KA, complete all as specified and directed by Engr-in-Charge.

Supply and fixing LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed by Engr-in-Charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed by Engr-in-Charge.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, complete all as specified and directed by Engr-in-Charge.

Supply & fixing metalic exhaust fans 300 mm sweep on wall with fixing metalic louvers (Iron shutter) in outer side of wall with suitable size anchor bolt and making connection of exhaust fan to ceiling rose by copper flexible wire, complete all as specified and as directed by the Engr-in-charge.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc, complete all as specified and directed by Engr-in-Charge.

M & L earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to galvanized earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of SSR part-I connected to earthing point of DBs, complete all as specified and directed by Engr-in-Charge including testing on completion.

Supply & laying XLPE insulated heavy duty electric power cables with multistranded aluminium conductor,1100 volts grade of size 16 sqmm 3 core, complete all as specified and directed by Engr-in-Charge.

Sand cushioning to underground cables complete all as specified in clause 19.75 of SSR Part-I (2009) laid before and after laying of cable, complete all as specified and directed by Engr-in-Charge.

M&L for old size sub class 'B' bricks laid in trenches as cable covers, complete all as specified and directed by Engr-in-Charge.

GI pipe of size 40mm dia light grade laid in trenches/walls including clamps,screws etc, complete all as specified and directed by Engr-in-Charge.

M/S NILIMA ENTERPRISES

KISHAN CONTRACTOR

surinder kumar jindal & bros.

M/S SEALINE BUILDERS