COMPREHENSIVE MAINTENANCE OF OTM ACCN, GUEST ROOM AND REPAIR OF SEWAGE LINE, MANHOLE, SEPTIC TANK, SOAKAGE WELL AND OTHER MISC WORK AT 5 AFLU AND OTHER AREA IN AOR OF GE (AF) FARIDABAD

Amount

Demolition/Dismantling of Brickwork or stone/ boulder masonry, built in cement mortar incl all quoins, arches, pillars, etc,complete all as specified and directed by Engineer-in-Charge.

M&L for Brickwork with subclass 'B' bricks (old size bricks), straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

All as per item No 02 above but except bricks.

M&L for brick work with sub class ‘B’ bricks (old size brick) straight or curved on plan to any radius in half bricks thick walls, built in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of new plastered surface and applying two coats of oil emulsion distemper on wall over one coat of primer etc complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plaster surface & apply two coats of cement based paint over a coat alkali primer resistance and complete all as specified and directed by Engineer-in-Charge.

M&L for two coat of Acrylic smooth exterior emulsion paint over one coat of acrlic primer incl preparation of new plasterd surface complete all as specified and directed by Engineer-in-Charge. Note : Colour as approved by Engr-in-Charge.

M & L for preparation of new plastered surface and applying two coats of oil emulsion distemper on ceiling over one coat of primer etc complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old surfaces by removal of existing treatmen and applying two coats of oil emulsion distemper over a coat of primer on surface of walls through electrical operated grinder etc, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old surfaces by removal of existing treatmen and applying one coat of oil emulsion distemper on surface of walls through electrical operated grinder etc, complete all as specified and directed by Engineer-in-Charge.

M&L for reparing of RCC projection, chajja, roof facia, celling by scrapping, cutting, derusting and cleaning exposed reinforcement surfaces of damaged loose RCC surface and applying neat cement slurry @ 3 kg/Sqm and filling the surface with cement plaster 1:3 one or two layer as reqd or PCC 1:2:4 with or without facia and smooth finished and smotth edges incl two coats of finished to match with the existing surface at any height and in any situation including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L cement concrete type B-2 1:2:4 (40mm graded stone aggregate) as in walls or retaining walls, any thickness, size or shape including pilasters buttreses columns, pillars, boundry pillars and posts and like for fixing of angle iron on top of boundry wall , including form work complete all as specified and directed by Engineer-in-Charge.

M & L for TMT bars 10mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with the mild steel wire (annealed) not less than 0.9mm dia or securing with clips and complete all as specified and directed by Engineer-in-Charge.

All as per item No 13 above but 6 to 8 mm dia and over and including in stirrups, spacers and binders

M&L for non skid ceramic coloiured tiles 7 to 8 mm thick (square/rectangular ) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm as in floor of shade & designed as approved by GE,set and jointed in neat cement slurry and pointed with white cement with colour pigment to match the colour of tiles,over and including 15 mm thick bedding layer or screed bed in cement mortar (1:6) in floors incl dismantling tiles etc complete all as specified and directed by Engineer-in-Charge.

All as per item No 15 above area of each tile exc 0.11 sqm but n.exec0.18 sqm, in Floor etc

M& L for Glazed ceramic jointless light/coloured group of size 350mmx450mm, thickness not less than 6mm as in vertical surfaces such as skirting/dado etc., set and jointed in neat cement slurry and pointed with white cement and pigment to match, laid over and including 10mm thick plastering in cement mortar 1:4, incl dismantling tiles etc ccomplete all as specified and directed by Engineer-in-Charge. Note : shade & design as approved by GE

M&L for Vtrified tiles light shade /dark shade 10 mm thick (square/ rectangular) polished, area of each tiles not exc 0.36 sqm , in floors, dado , skirting etc. set and jointed in neat cement slurry over 15 mm thick screed bed or bedding layer in CM 1:4 for laying floor finishes and pointed in white or coloured cement to match and incl dismantling tiles etc complete all as specified and directed by Engineer-in-Charge.

All as per item No 18 above area of each tiles exc 0.36 sqm but not exc 0.42 sqm, in floors etc

M&L for 20 to 25 mm thick Kota stone slab (Machine cut) of any size laid over and incl 20mm thick bedding layer in cement mortar 1:6 over neat cement slurry @ 3Kg/sqm over sub base , jointed and pointed in grey cement mixed with pigment to match the shade of slab including rubbing and polishing to achieve mirror finish complete as in flooring /steps/ riser / skirting incl dismantling stone slabs etc complete all as specified and directed by Engineer-in-Charge.

M&L for Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of Makrana white incl roundening the edge of stone complete all as specified and directed by Engineer-in-Charge.

M&L for Granite 18-20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl moulding ,rounding of edgeing and dismantling complete all as specified and directed by Engineer-in-Charge.

M&L for 25 mm thick PCC type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) as in laying of floor finishes incl demolition complete all as specified and directed by Engineer-in-Charge.

M & L for 100mm thick PCC 1:2:4 type B-2 (using 40 mm graded stone agg. ) in hardstanding /base of flooring incl demolition complete all as specified and directed by Engineer-in-Charge.

M & L for 75 mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone agg. ) in sub base of flooring incl demolition complete all as specified and directed by Engineer-in-Charge.

M & L for 50 mm thick PCC 1:3:6 type C-2 (using 40 mm graded stone agg. agg. ) as in plinth protection / path/ any paved area incl demolition complete all as specified and directed by Engineer-in-Charge.

M & L for chequered tiles of size 300 x 300 x 25 mm thick (colour and glazed approved by EIC) with grey cement and pigments laid over and including 15 mm thick screed bed in CM 1:6 bedded and jointed in neat cement slurry, incl dismantling complete all as specified and directed by Engineer-in-Charge.

M&L for machine pressed precast concrete interlocking paver block of 60mm thickness any shape and size confirming to IS 15658 -2006, with grey cement, pigment incl 25mm thick sand filling complete all as specified and directed by Engineer-in-Charge.

M & L broken stone hard core of gauge n.exc. 63mm, deposited, spread and leveled in layers n.exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engineer-in-Charge.

M & L for PCC 1:2:4 Type B-2 (using 40mm graded stone aggregate) as in flooring incl finishing the cement concrete surface even and smooth with using extra cement , rubbish off the primises and incl demolition complete all as specified and directed by Engineer-in-Charge.

M&L for Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade 'A' in on concrete slab 100mm complete all as specified and directed by Engineer-in-Charge.

M&L for anodised aluminium framed work for door, window / vent (powder coated) aluminium section weighting 0.55kg/RM with one or more rebated incl jointed cleat for fixing etc complete all as specified and directed by Engineer-in-Charge.

M&L for anodised aluminium powder coated door shutter , aluminium section weighting not less than 0.55kg/RM incl necessary 4.8mm th sheet glass ordinary quality / frosted glass or ACP sheet incl joining with cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, lock , 2 x 150mm aluminium handles, 3 x 100mm hinges aluminium, 2 x 150mm Aluminium tower bolts,1xdoor stoper,1xHydralic door closer with each shutter any type incl taking down complete all as specified and directed by Engineer-in-Charge.

M&L for anodised aluminium powder coated window and ventilator shutters, aluminium section weighting not less than 0.55kg/RM incl necessary 4.8mm th sheet glass ordinary quality glass/ frosted incl joining with cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, lock , 2 x 150mm aluminium handles, 3 x 100mm hinges aluminium, 2 x 150mm Aluminium tower bolts complete all as specified and directed by Engineer-in-Charge.

M&L for aluminium Anodized powder coated fixed frame of partiton or fixed window / ventilator , aluminium section weighting not less than 0.55kg/RM incl 4.8mm thick sheet glass oridinary quality ' frosted glass or ACP sheet joining with rubber beading , aluminium snap beading complete all as specified and directed by Engineer-in-Charge.

S&F aluminium wire guard mesh of 4mm nominal dia of wire and average width of aperture 75 - 85mm and fixed with aluminium frame / staples complete all as specified and directed by Engineer-in-Charge.

M&L for 4.8 mm thick float glass ordinary quality' frosted glass and glazing with aluminum beeding and gasket to aluminum framework in square exc 0.50 sqm in each pane in repair complete all as specified and directed by Engineer-in-Charge.

S & F for plain gypsum board panel 12.5mm thick on ceiling with and incl necessary GI frame used with ' T ' or any section accessories etc of galvanized steel all as per manufacturer design conforming to IS-2095 and 2542(1981) the weight of the board shall be not less than 7 kg per sqm incl dismantling of walls and ceiling board any type and two coat of OBD over a coat of putty complete all as specified and directed by Engineer-in-Charge.

M&L in repair for PVC hollow wall panelling 7 to 8mm thick any colour/design approved by engr-in-charge, inclusive of fixing on to wall incl moulding end caps fixed with PVC sleeves and screws as required at site complete all as specified and directed by Engineer-in-Charge.

S & F for 10 -12 mm thick glass door, frosted with certain logo, fixed with floor spring, fixed on floor with two nos stainless steel handle of 300mm on each leaf and fixed partition arrangement incl necessary provision to lock the door complete all as specified and directed by Engineer-in-Charge.

M&L for providing and fixing 10 mm thick plaster of paris ceiling (Gypsum anhydrous) of approved design/ pattern to flat surfaces incl all necessary MS frame work, 12 mm thick board and fittings as per standard practice and as per manufacturer's instrs reinforced with GI wire mesh incl dismantling of walls and ceiling board any type complete all as specified and directed by Engineer-in-Charge.

M&L for providing & fixing False ceiling with Gypsum based ceiling tiles and frame work (with aluminum foil on one side) of size 595 x 595 mm of thickness not less than 9 mm including with GI powder coated frame angle /tee grid frame work for ceiling with following specfication (a) S&F Angle of side 25x25x1mm powder coated (b) 25x25x1 mm GI powder coated at Bottom tee as in main member (c) 25x25x1 mm thick GI powder coated at bottom tee as ibn cross members (d) S&F 1.6mm dia GI wire suspenders alongwith adjustable clamps to maintains leveling inculding fixing to ceiling fasteners & dismantling of walls and ceiling board any type complete all as specified and directed by Engineer-in-Charge.

M&L for coral wall texture paint flasks type consisting of fiber natural gem, semi-precious pigmented granules, pearl and spary texture of high resistance, fire proof polymer alkali resistance, anti-corrosion and anti-condensation with natural stone, lime stone quartz etc. that given a scam less wall surface without joints, reples water ultra violet rays from sunlight including removing of, alage and fungus applied on wall or ceiling with trowel and roller complete all as specified and directed by Engineer-in-Charge.

M&L for Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm including removing of, alage and fungus applied on wall with trowel /roller complete all as specified and directed by Engineer-in-Charge.

M&L for box type steel window 1.25 mm thick made of ERW tube P-Section of size 60 x 25 mm double rebated outer frame comprise of glazed skeleton shutter(two gauged shutters and two glazed shutter) of ERW tube P-Section size 50 x 20 mm and 1mm thick one/two Nos openable leaf consisting of two Nos sash bar of T-Section 20x3mm welded to frame with one No Vertical mullion of ERW box type T-Section of size 60 x 25 mm and 1.25 mm thick and FI 2 mm thick welded / screwed to frame for fixing of glass including fittings and fixture like Handle, Tower Bolt, stopper, cleat, pintal hinges, hold fast etc. (i) Hold Fast, 150mm long of 120mm x 3 mm made to shape -04 Nos per window. (ii) Handle of Z sec 20mm x 25mm, 100 mm long -1 No per leaf (iii) MS Tower bolt 150mm long - 2 No per leaf (iv) Z Sec 20mm x 25 mm, 100 mm long stopper - 1 No per leaf (v) Cleat 55 mm long of hollow square 15mm x 20mm x.63mm welded to hinge -1 No per leaf. (vi) MS Pintal hinges of size 75mm x 12mm - 2 Nos per leaf . (vii) 8 mm square guard bar, 10 cm centre to centre. (viii) 40x6 mm flat iron all around for joint of both frame. (ix) stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples & 3mm thick, sheet glass ordinary quality and glazing with oil putty .(x) Two coat of synthetic enamel paint to MS window and guard bar , Incl taking down old steel / wooden window and making good dismantled portion with PCC 1:2:4 type B0 incl hold fast PCC (four No’s for Each window) & around required plaster in CM 1:4 and match with existing finishing complete all as specified and directed by Engineer-in-Charge.

M&L for pressed steel frames of size 105mmx60mm for doors with one or more rebates fabricated out of 1.25mm thick mild steel sheets including necessary fixing lugs, butt hinges (100mm medium weight-03 Nos), lock strike plate with and including filling of hollow portion in PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate and making good the existing surface in cement mortar 1:6, incl taking down old frame/chowkat complete all as specified and directed by Engineer-in-Charge.

All as per item No 46 above size of frame 125mmx60mm for doors complete all as specified and directed by Engineer-in-Charge.

S&F for factory made 35mm thick 2nd class hardwood plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge.

S&F for 35mm thick flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides and one face is covered with decorative face veneer with lipping/frame to match incl taking down old shutter complete all as specified and directed by Engineer-in-Charge.

S&F for 2nd class H.W. glazed and skelton door shutters 35mm thick, open rebated and prepared to received glass/gauge etc (without sash bars) edges of framing plain, chamfered or rounded and mitred , beads for securing glass etc the size of member of shutter as specified in SSR part-I clause 8.23(b) and fitted to chowkahts incl stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads & taking down old shutter etc complete all as specified and directed by Engineer-in-Charge.

S & F solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube incl taking down old frame any type complete all as specified and directed by Engineer-in-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be convered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20 mm width stuck inside with solvant cement for stiles and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert of top rail and bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and raials with suitabale PVC sheet beading, and jointed together with solvant cement, fixing in the frame at side as per specification and drawing incl taking down old shutter & 3Nos- 100mm Aluminium hinges for each shutter complete all as specified and directed .

S & F for Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed by Engineer-in-Charge.

S & F for 3mm thick sheet glass ordinary quality glazing with oil putty in square n exc 0.5 sqm quality or description from steel frame and complete all as specified and directed by Engineer-in-Charge.

S & F for mild steel framed work as in grill, guard bars etc with ends of bars/FI shoulders and or riveted or forged in to spikes, framed guard bar and similar works confirming to Fe 410-0 or Fe 310-0 complete all as specified and directed by Engineer-in-Charge.

S & F in repair for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads complete all as specified and directed by Engineer-in-Charge.

S & F in repair 3mm thick sheet glass, ordinary quality and with oil putty in Square n. exc 0.5 sqm in each pane incl hacking out old broken glass from metal frame incl punching or drilling out old glazing pins/spring clips and glazed with oil putty complete all as specified and directed by Engineer-in-Charge.

S&F for MS butt hinges, medium weight, cold rolled mild steel 100mm long (ISI Marked) with welded or complete all as specified and directed by Engineer-in-Charge.

S&F for aluminum anodized barrel tower bolts of extruded section 150mm long (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F for aluminum handles cast type anodized 200mm long (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F for 250mm long aluminium alloy, anodised, sliding door bolt of 16mm dia with hasp, staple (bolt type) and fixing clips of sheet, extruded sections and fixing bolts and sliding bolts of extruded sections complete all as specified and directed by Engineer-in-Charge.

S&F in repair, 150 mm ordinay rat tail rod pattern springs incl roller and rabber plate fixed to chowkhats in repairs incl necessary welding if reqd complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new steel or iron surfaces of any description not otherwise described over 10 cm girth or width and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge.

M & L for one coat of synthetic enamel paint on steel surface including preparation of old steel surface width or girth exc 10cm complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of synthetic enamel paint over a coat of pink primer on wooden new surfaces of any description over 10cm width or girth incl preparation of new surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for one coats of synthetic enamel paint on wooden surfaces of any description over 10cm width or girth including preparation of old surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for 18mm thick water proof solid MDF Board prelaminated both sides of approved shade fitted with necessary arrangement as in kitchen cabinet back sides, partition, shutters and shelves, etc., fixed with solvent cement adhesive and stainless steel screws and providing 1mm thick PVC lipping to exposed edges, complete all as specified and directed by Engineer-in-Charge.

M&L for extruded brass handle, fancy type as approved by the GE, polished, 150mm long (ISI marked), complete all as specified and directed by Engineer-in-Charge.

M&L for continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when open) 30mm, complete all as specified and directed by Engineer-in-Charge.

M&L for aluminium Fanlight catch with 14mm catch and fixed suitable for any shutters, complete all as specified and directed by Engineer-in-Charge.

M & L for viterous china squating pan of (Orrissa Pattern) size 580x440 mm white with 'P' or 'S' trap front or back inlet and integral foot rest (excluding flushing cisteern and flush pipe) fixed in repair including lime concrete bedding as required set complete all as specified and directed by Engineer-in-Charge.

S&F for Vitreous China wash down water closet pan (pedestal pattern) with trap, white (excluding fixing bolts, flushing cistern and flush pipe) incl connection to drain and flushing pipe in repairs complete all as specified and directed by Engineer-in-Charge.

S&F of PVC flushing cistem low level white with all accessories of 10 ltrs capacity incl flushing pipe, brackets and taking down of old CI/PVC flushing cistern in repairs complete all as specified and directed by Engineer-in-Charge.

S&F for Vitreous China wash basin (Pedestal pattern), White, flat back, size 550x400 mm incl brass CP waste coupling 32mm dia with long screwed shank and fly nuts,32mm dia, chain and plug, porcelain stopper with and including PVC collapsible waste pipe of suitable length, fixed in repairs complete all as specified and directed by Engineer-in-Charge.

S&F for One piece water closet with bowl for cupled WC with PP soft seat cover, cistern hinges fixing accessories and accessories set of size 650x375x750mm, 3.S trap outlet with cistern fittings and necessary fixing fittings complete, fixed in repairs, complete all as specified and directed by Engineer-in-Charge.

S&F for wall mixer with provision for overhead showes with 115mm long bend pipe on upper side, connecting legs and wall flanges, in repairs complete all as specified and directed by Engineer-in-Charge.

S&F for CP brass Centre hole mixer without pop up waste system 15mm bore for mixing hot and cold water screwed down for iron pipe for WHB, in repairs complete all as specified and directed by Engineer-in-Charge.

S&F for Soap tray brass chromium plated and fixed to plugs on wall with brass screws, complete all as specified and directed by Engineer-in-Charge.

S&F in repair Soap dish, vitreous China white, ap?proximate size 160x 160x90mm fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge.

S&F in repairs for Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified and directed by Engineer-in-Charge.

S&F for Towel ring brass chromium plated, fixed with brass screws and plugs, complete all as specified and directed by Engineer-in-Charge.

S&F for Brass Chromium plated shower roses 125 mm size incl arm with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed by Engineer-in-Charge.

S&F in repair Stainless steel sink without drainboard, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm etc complete all as specified and directed by Engineer-in-Charge.

S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe incl sink coupling, 40mm waste fitting, overall size 915mmx460mm with bowl size 410 mm x 330mm x 160mm, etc complete all as specified and directed by Engineer-in-Charge.

S&F for Toilet paper holder,stainless steel, fixed with and including chromium plated brass screws and and wooden/plastic cleats on walls, complete all as specified and directed by Engineer-in-Charge.

S&F for Health faucet brass CP with 8mm dia 1.2 mtr long flexible pipe and wall hook fixed with brass chromium plated screws, complete all as specified and directed by Engineer-in-Charge.

S&F in repair for Bottle trap of PTMT having minimum water seal of 25mm .(Minimum weight 32mm-260gms/40mm-270 gms), complete all as specified and directed by Engineer-in-Charge.

S&F for 25 mm dia decorative/fancy type stainless steel curtain rod with brackets and knobs at both ends as per site requirement incl taking down old existing pipes with accessories complete all as specified and directed by Engineer-in-Charge. Note: the cost of brackets and knobs is deemed to be incl in the quoted rate.

S & F for Bib tap CP fancy type long body 15 mm bore with will crutch or buttewrfly handle screwed down screwed to iron pipe in repairs complete with all fittings complete all as specified and directed by Engineer-in-Charge.

S & F in repair Stop cock /angle CP fancy type 15 mm bore screwed down high pressure with crutch or butterfly handle & screw both end for iron pipe or for Unions complete all as specified and directed by Engineer-in-Charge.

S & F in repair Stop cock concealed long shank chromium plated fancy type 15 mm bore screwed down high pressure with crutch or butter fly handle complete all as specified and directed by Engineer-in-Charge.

S& F for 15 mm swan neck pillar cock fancy type chromium plated screw with iron pipe incl all fittings in repairscomplete all as specified and directed by Engineer-in-Charge.

S&F for PVC connections 60cm long superior quality with PTMT nut on both side complete all as specified and directed by Engineer-in-Charge.

S&F in repair grating round 125mm size of CP complete all as specified and directed by Engineer-in-Charge.

S&F in repair 32 mm dia Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm?45gms/ 40mm-60 gms) complete all as specified and directed by Engineer-in-Charge.

S&F in repair 40 mm dia Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm?45gms/ 40mm-60 gms) complete all as specified and directed by Engineer-in-Charge.

S & F in repair vitreous china urinals, half stall type (635x450mm) , complete including providing and fixing , bedding urinal against wall in cement mortar 1:2 , pointing around urinal back in cement , grating and union for discharge pipe, CP urinal spreader and fitting with bottel trap & CP waste coupling complete all as specified and directed by Engineer-in-Charge.

S&F in repair PVC water tank lid with locking arrangement complete capacity (500 ltr -1000 Ltr) complete all as specified and directed by Engineer-in-Charge.

S&F in repair for rotational moulded polyetheylene water storage tanks (cylingrical verticlal with closed top) of 500 ltr capacity, hoisted and fixed in any position incl 20 mm dia ball float valve with aluminium fitting, GI nipple and any fitting ,dismantling existing water tank complete all as specified and directed by Engineer-in-Charge.

S&F in repair for rotational moulded polyetheylene water storage tanks (cylingrical verticlal with closed top) of 1000 ltr capacity, hoisted and fixed in any position incl 20 mm dia ball float valve with aluminium fitting,GI nipple and any fitting , tank cover dismantling existing water tank complete all as specified and directed by Engineer-in-Charge.

Taking up or down 15 mm dia bore steel tubing and connection including cleaning for refixing or removed to store complete all as specified and directed by Engineer-in-Charge.

S&F for GI tubing 15mm bore medium grde with all fittings and fixed complete to wall and ceiling or laid in floors etc incl cutting chases in brick wall pinning in making good in CM 1:3 to facings where required complete all as specified and directed by Engineer-in-Charge.

S&F GI tubing 15 mm bore medium grade medium grde with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

Fixing only in repair steel tubing and connection 15 mm dia bore to wall and laid in floors complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connection including cleaning for refixing or removed to store, 20 mm dia bore complete all as specified and directed by Engineer-in-Charge.

S&F GI tubing 20 mm bore medium grade medium grde with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

Fixing only in repair steel tubing and connection 20 mm dia bore to wall and laid in floors complete all as specified and directed by Engineer-in-Charge.

S&Fin repair for Gun-metal globe or gate valves of 20mm bore , with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repair 25 mm PVC float valve incl ball and rod complete all as specified and directed by Engineer-in-Charge.

S&F in repair 20 mm PVC float valve incl ball and rod complete all as specified and directed by Engineer-in-Charge.

S&F in repair cast iron body Door closer hydrau?lically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete unreinforced in of any desciption and in any position not otherwise specifically provided for (sunken floor) and concrete debris and rubbishoff to a distance n exc 100m complete all as specified and directed by Engineer-in-Charge.

M&L, for rendering 10mm thick in CM 1:3 with WPC @ 3% weight of cement in sunken slab complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of roof surface & applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm including APP based polymeric membrane minimum weighing 3.8 kg/sqm and minimum 3 mm thick reinforced wih polyster non wove fabric (wt not less than 150 gms/sqm) land on primed surface by forced application, joints to be touched hot and width of overlaps not be less than 150 mm complete all as specified and directed by Engineer-in-Charge.

M&L, cement concrete 1:7:12 F-2 (40 mm graded stone aggregate) in lean concrete complete all as specified and directed by Engineer-in-Charge.

M&L for repairs to collapsible steel gate including necessary gressing, welding, locking arrangement including serviceing etc complete as to bring in service condtions complete all as specified and directed by Engineer-in-Charge.

Dismanting of rolling shutter complete all as specified and directed by Engineer-in-Charge.

S&F 1.25mm thick Steel rolling shutters, gear operated type with bevel gear box and crank handle, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type complete all as specified and directed by Engineer-in-Charge.

S&F Safety lever locks mild steel with 4 levers incl ball bearing for rolling shutters complete all as specified and directed by Engineer-in-Charge.

S&F for 4mm thick acrylic sheet board of High quality with Media printing of 3m of best quality (size/frame of board , design of bd , type of print on sheet , size of studd , samples of letter, pictures, writing will be provided by accepting officer or Engr-in-Charge) and fixed at any height from GL to 29 Mtr height incl stainless steel studds (min 4 studs at each board / sheet ) incl dismantling of existing damaged sheets complete all as specified and directed by Engineer-in-Charge. Note : Minimum weight of Acrylic Sheet not less than 4.70kg per sqm.

Dismantling of polycarbonated sandwithch type sheets complete all as specified and directed by Engineer-in-Charge.

S&f 6.00 mm thick polycarbonate sandwitch type sheets in semi circle shape on roofs of desired colour and fixed with aluminium metal flat / angle / tee sections including rubber beadings and silicon water proofing sealent jell for joining the sheets together and self tightening screws of reputed quality and make complete all as specified and directed by Engineer-in-Charge.

S&F in repair 15 mm bore Twin one angle valve/ bib tap cast copper alloy chromium plated, fancy type, screwed down high pressure, screwed both ends for iron pipe or for union complete all as specified and directed by Engineer-in-Charge.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer-in-Charge.

S&F in repair corner shelf with CP railing 300mm x 300mm complete all as specified and directed by Engineer-in-Charge.

S&F in repair CP jet for EWC along with PVC connection complete all as specified and directed by Engineer-in-Charge.

S&F CP brass Health faucet with 15mm bore pipe complete all as specified and directed by Engineer-in-Charge.

S&F for liquid soap container of PTMT fixed with and incl CP brass screws and wooden/plastic cleats complete all as specified and directed by Engineer-in-Charge.

S&F ventia blind for window including necessary items required for fix to wall complete all as specified and directed by Engineer-in-Charge.

S&F in repair door seals made of aluminium strip powder coated 20 mm wide and provided rubber/ cotton mat lining fixed with screws to door shutters up to 1m width opening complete all as specified and directed by Engineer-in-Charge.

S&F double legged door stopper of aluminium alloy with rubber complete all as specified and directed by Engineer-in-Charge.

S&F 4mm thick figured glass pane fixed in window shutter/ventilators including necessary beading/wooden beading andoil putty complete all as specified and directed by Engineer-in-Charge.

Dismantling of plain or corrugated steel sheeting, any gauge thickness including Nainital or similar pattern roof coverings complete all as specified and directed by Engineer in Charge.

S&F 0.63 mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap with L type or J-type or cranked hook bolts in lieu of screws in roofs, wall etc with grade of zinc coating complete all as specified and directed by Engineer in Charge.

All as per item No 140 but except Sheets

S&F 0.63 mm thick Plain, galvanised, mild steel sheeting in ridges, hips valley gutters drip and straight flashings (length and girth as fixed) with grade of zinc coating complete all as specified and directed by Engineer in Charge.

M&L for preparing new zinc (or galvanised) surfaces to receive painting by coating with mordant solution including washing and cleaning etc steel and iron surfaces and applying two coat of synthetic enamel paint of any description over 10 cm width or girth in CCD pattern as approved complete all as specified and directed by Engineer in Charge.

S&F for 110 mm bore PVC pipes single socketed pressure rating @ 4Kg/Sq cm length 'Medium grade' with rubber ring joint, fixed to walls with dash ture nut and bolt at every 2 mtrs length complete, incl taking up/down old pipe with all fittings all as specified and and directed by Engineer in Charge.

Cleaning /removal of blockage 150 mm bore SWG pipes of depth not exc 1.50 mtr with mechnical process incl removing RCC man hole covers and refixing the same as before complete all as specified and directed by Engineer-in-Charge.

Cleaning /removal of blockage 150 mm bore SWG pipes of depth exc 1.50 mtr but not exc 3.00 mtr with mechnical process incl removing RCC man hole covers and refixing the same as before complete all as specified and directed by Engineer-in-Charge.

Dewatering/desilting of existing manholes of any size depth and removing of all solid/semi-solid matter of silt residue both organic or inorganic in nature (mechanical system or using suction pump where ever required up to any depth )and incl removing RCC manhole Covers and refixing the same after making the manhole fully functional, complete all as directed by Engineer-in-charge.

Dewatering/desilting for the septic tank of any capacity exc1.50 m and n.exc 4.5 m deep solid/semi-solid matter of silt residue both organic or inorganic in nature ( mechanical system or using suction pump where ever required up to any depth by working under foul conditions and disposal of the same in out of MoD area, complete all as directed by Engineer-in-charge. Note for Item : The Septic tank shall be measured more than one time as per requirment and directed by Egnr-in-Charge.

Excavation in trenches n exc 1.5m wide and n exc 1.5m deep and getting out in soft or loose soil for shafts, wells,drains, manholes etc n exc 10Sqm on plan for sewage line & foundation etc complete all as specified and directed by Engineer-in-Charge.

All as per item No 149 but exceeding 1.5 M depth and not exceeding 3 M for foundation, etc and getting out in Soft/ Loose soil.

All as per item No 150 but exceeding 3.0 M depth and not exceeding 4.50M for foundation, etc and getting out in Soft/ Loose soil.

Demolition and breaking up drain pipes 100mm dia ( Salt Glazed ware, AC or reinforced concrete) set in cement mortar including PCC bed and haunching and removal of debris outside the MD land complete all as specified and directed by Engineer-in-Charge.

Demoltion and breaking up existing sewag(SWR/ AC pipes and the like, 150mm bore set in cement mortar and removing demolished material to a distance exc 50m and n exc 100m complete all as specified and directed by Engineer-in-Charge.

Demoltion and breaking up existing sewage (SGSW / AC pipes and the like, 200mm bore set in cement mortar and removing demolished material to a distance exc 50m and n exc 100m complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm PVC (SWR ) , pipes single socketd , in any length with rubber ring joints , laid in trenches or in floor complete all as specified and directed by Engineer-in-Charge.

S & F RCC Class NP 3, 150 mm bore pipes laid and jointed complete with collars complete all as specified and directed by Engineer-in-Charge.

S & F RCC Class NP 3, 200 mm bore pipes laid and jointed complete with collars complete all as specified and directed by Engineer-in-Charge.

M & L for PCC 1:3:6 type C2 (using 40 mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 100 mm bore complete all as specified and directed by Engineer-in-Charge.

M & L for PCC 1:3:6 type C2 (using 40 mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150 mm bore complete all as specified and directed by Engineer-in-Charge.

M & L for PCC 1:3:6 type C2 (using 40 mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 200 mm bore complete all as specified and directed by Engineer-in-Charge.

S & F in repair for precast factry made reinforced cement concrete Manhole cover (Ist quality) including grove and hook arrangement for lifting and placing in position and sides covered by MS sheet medium duty of 60mm thick (size of the cover will be itimated by the EIC) complete all as specified and directed by Engineer-in-Charge.

S&F mild steel work such as in angle iron, flat iron fillets etc for horn, fixing of barbed wire to RCC post, securing wire mesh etc. including all necessary cuttings, drilling, bolting or riveting etc and including 10mm MS bars as in tie bars fixed to fencing posts including necessary welding where required, as per site requirement and other similar works complete, conforming to Fe-290 Gde E-165 complete all as specified and directed by Engineer-in-Charge.

S&F in repair precast factory made polycrete (SFRC) medium duty perforated drain cover 100 mm thick rectangle in shape upto 01 sqm area each with hole for drain complete all as specified and directed by Engineer-in-Charge.

Returning, filling in soil including spreading, levelling, watering and well ramming in layers n.exc. 25cm complete all as specified and directed by Engineer-in-Charge.

M&L for Plain cement concrete (1:2:4) Type B-1, (using 20mm graded crushed stone aggregate), as in copings, kneelers , apex stones,bed plates, including weathering ,slightly rounded /benching or chamfered angles and throating ,( Rates include for use of formwork) complete all as specified and directed by Engineer-in-Charge.

Cutting into existing manholes for connecting new drains making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as required, 100mm dia pipe complete all as specified and directed by Engineer-in-Charge.

Cutting into existing manholes for connecting new drains making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as required, 150mm dia pipe complete all as specified and directed by Engineer-in-Charge.

Cutting into existing manholes for connecting new drains making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as required, 200mm dia pipe complete all as specified and directed by Engineer-in-Charge.

M&L for salt glazed stoneware gully trap, square or round moulded type 'P', 150x150mm size complete all as specified and directed by Engineer-in-Charge.

M&L for cement concrete 1:3:6 type C2 (using 20 mm graded stone aggregate) as in surface channels, drains and bed of manhole complete all as specified and directed by Engineer-in-Charge.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed by Engineer-in-Charge.

M & L for cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation filling, and mass concrete complete all as specified and directed by Engineer-in-Charge.

M&L for loose filling with broken bricks aggregate of gauge 80 to 150mm in soakage pits, soakage wells complete all as specified and directed by Engineer-in-Charge.

M&L for loose filling with broken bricks aggregate of gauge 40 to 80mm in soakage pits, soakage wells complete all as specified and directed by Engineer-in-Charge.

S&F for 100mm bore Cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls etc incl taking down old pipe complete all as specified and directed by Engineer-in-Charge.

S&F for 75mm bore Cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls etc complete incl taking down old pipe complete all as specified and directed by Engineer-in-Charge.

S&F for 100mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed by Engineer-in-Charge.

S&F 75mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed by Engineer-in-Charge.

S&F for 100mm branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches/ Tee etc complete all as specified and directed by Engineer-in-Charge.

S&F for 75mm branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches/ Tee etc complete all as specified and directed by Engineer-in-Charge.

S& F for 75 Cast Iron Cowl complete all as specified and directed by Engineer-in-Charge.

S& F for 100 Cast Iron Cowl complete all as specified and directed by Engineer-in-Charge.

S&F for 75mm dia of outlet cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer-in-Charge.

S&F for 100mm dia of outlet cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer-in-Charge.

S&F for 110mm bore PVC pipes single socketed Pressure rating @4Kg/Sq cm length "medium grade " with rubber ring joint, fixed to walls with nut and bolt at every 2 mtrs length complete , incl taking up/down old pipe with all fittings complete all as specified and directed by Engineer-in-Charge.

All as per item No 185 above but laid in trench or in floor

S&F for 110mm bore PVC bends/junction any radius complete all as specified and directed by Engineer-in-Charge.

S&F for 110mm bore PVC bends/junction with access door any radius complete all as specified and directed by Engineer-in-Charge.

S&F for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

S&F for 75mm dia PVC (SWR) multi floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

S&F for 75 mm bore PVC pipes single socketed Pressure rating @4Kg/Sq cm length "medium grade " with rubber ring joint, fixed to walls with nut and bolt at every 2 mtrs length complete , incl taking up/down old pipe with all fittings complete all as specified and directed by Engineer-in-Charge.

S&F for 75 mm bore PVC bends/junction any radius complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) floor trap, plain with CP grating including jointing with solvent cement, 75mm diameter of outlet, complete all as specified and directed by Engineer-in-Charge.

Removing excavated material n. exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point complete all as specified and directed by Engineer-in-Charge.

S&F SFRC drain covers with perforated holes factory made of size 0.50m x 1m x 75mm thick complete all as specified and directed by Engineer-in-Charge.

M&L for RCC 1:2:4 (using 20mm graded agg) pre cast cover slabs ( for manholes etc) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles all as specfied with one hole at centre and both side ring to carrying complete all as specified and directed by Engineer-in-Charge.

M&L for TMT Bar 10mm dia and over cut to length bend t shape required including cranking, bending sprilly for hooping columns hooking ends and binding with and incl MS wire (Anneled) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

S&F for 300mm dia of NP3 reinforced concrete pipes, laid and jointed complete with collars complete all as specified and directed by Engineer-in-Charge.

S&F for 200mm dia of NP3 reinforced concrete pipes laid and jointed complete with collars complete all as specified and directed by Engineer-in-Charge.

M&L for framed work such as grills, gratings etc with ends of bars shoulddered and /or riveted or forged into spikes framed guard bars barred iron doors ladders framed balusters walk ways railings framework of wter tandks and similas work complete all as specified and directed by Engineer-in-Charge.

Returning filling in, including spreading leveling watering and wall ramming in layers not exc 25 cm complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete unreinforced in ground floors and paving n. exc 15 cm thickness below or above ground level, concrete debris and rubbish to a distance n exc 100m complete all as specified and directed by Engineer-in-Charge.

M&L for 75 mm thick PCC 1:4:8 type D-2 (using 40mm graded stone agg) in sub base of flooring and complete all as specified and directed by Engineer-in-Charge.

M&L for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658 - 2006 of 60mm thickness with grey cement pigment complete all as specified and directed by Engineer-in-Charge.

M&L for chequered tiles of size 300 x 300 x 25 mm thick (colour and glazed approved by EIC) with grey cement and pigments laid over 15 mm thick screed bed in CM 1:6 bedded and jointed in neat cement slurry, incl dismantling complete all as specified and directed by Engineer-in-Charge.

M&L for 50 mm thick PCC 1:3:6 type C-2 (using 40 mm graded stone agg) as in plinth protection/path/ any paved area complete all as specified and directed by Engineer-in-Charge.

High Tech Metal India

M/S Ashoka Engineers and contractors

SAGAR ENTERPRISES