Construction of 30 Bedded Integrated AYUSH Hospital,near Wellness Park, Gangtok District, Sikkim.

Amount

BUILDING PORTION

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Providing & Laying in position cement concrete of 1:3:6 mix. (1 cement, 3 coarse sand, 6 graded stone aggregate of 20mm & down size)

Filling inside plinth in building works with 23 cm layers, consolidated to 15cm including watering, ramming etc. all complete.

Providing and Laying damp proof coarse 40 mm thick with cement concrete 1:2:4 ( 1 cement, 2 Clean coarse sand, 4 graded stone aggregate 12.5 mm & nominal size) as per the direction of Engineer in Charge.

Filling with available excavated earth in trenches, plinth and side of foundation in building works with layers not exceeding 20cm in depth including consolidation of each layer by ramming, watering etc, all complete.

Providing and Laying in position 1:1:2 Mix (1cement, 1 coarse sand 2 graded stone aggregate 20mm and down nominal gauge) of reinforced cement concrete excluding the cost of form work, finishing and reinforcements.

Providing, fixing & removing form work for casting R.C.C items as indicated below: with locally available timber)

Foundation, footings, base of column etc. for mass concrete.

Foundation base

Square columns

Form work for beam, lintels, girders, brersumers & cantilevers.

Floor slab, roof slab, landing, balcony & access platform.

Supplying, bending and placing in position of Tor steel reinforcement in all R.C.C works i/c cost of binding wires all complete.

Providing and laying first class brick work in half brick thick in superstructure of standard size bricks with 1:4 cement mortar (1 cement and 4 coarse sand) including carriage of bricks upto work site and curing etc. all complete.

Providing and laying 15mm thick cement plaster of 1:3 mix in single coat including finishing even & smooth and curing etc. all complete.

Providing and Laying white or colored glazed vitrified tiles Pearl (white, marvel Atlanta, jet black etc or equivalent) in flooring, treads of steps landing etc laid on a bed of 15mm, cm 1:3 (1cement, 3coarse sand) finished with flush pointing with white cement slurry.

Providing and Laying white or colored glazed tiles anti skid ( elegant, cashmere, Egyptian rustic, celebrity, lara etc or equivalent) of glossy series or celebrity, elegant or equivalent in flooring, treads of steps landing etc of size 300mm x 300mm laid on a bed of 15mm, cm 1:3 (1cement, 3coarse sand) finished with flush pointing with white cement slurry.

Providing and Laying white or colored or ceramic glazed tiles of size 200mm x 300mm Special colour(black, burgundy, pink, midnight blue, alpine blue or equivalent) in skirting, risers of steps and Dados on 12mm thick cement plaster (1cement, 3coarsed sand) 1:3 bare and jointed with white cement slurry.

Providing and Laying Chequers tiles in on flooring over 12mm thick cement plaster (1cement, 3coarsed sand) 1:3 bare and jointed with white cement slurry.

Providing and Laying 20mm thick granite stone in Risers of steps, skirting and pads, walls, pillars etc laid on 10mm thick base c.m. 1:3 joint treated with white cement, mixed with matching pigment, curing including rubbing to give a granite finish, as per the direction of Engineer in Charge and carriage of material up to work site, all complete.

Providing / Fitting / Fixing in position suspended exposed grid false ceiling using E-Board pearl (tested for inflammability as per IS 11871)& E- Grid of grid size 1200 x 600 x/600 x 600 mm with main runners 39 x 24.7 mm cross Tee 29 x 24.7mm and wall angle 22.2 x 22.2 mm placing 4mm thick E-Board pearl in the grid of E-Grid duly suspended with 4mm dia GI bars hangers fixed with tee dash fastener of fro purlin of the roof with butterfly clips & hold down clips, providing provision for light fixtures air conditioning diffuser and ducts, sprinklers, smoke, detectors i/c paintings water based acrylic cement primer etc all complete:

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately)

Casement window double panels with S.S. friction hinges (350 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.50 sqm).

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing

Casement door with top hung ventilator with 3D and S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ±. 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(Area of door upto 2.50 sqm)

Providing and fixing anodized aluminum works for doors, windows, ventilators and partitions with extruded built up standard tubular or other section of approved make confirming IS 733 and IS 1285, fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners i/c necessary filling up the gaps at junctions, at top, bottom and sides with required PVC / neoprene felt, etc. Al. section shall be smooth, rust free, straight, mitered and joined mechanically wherever required i/c cleat angle, Al snap beading for glazing / paneling CP brass / stainless screws, all complete as per design and drawings and the direction of the Engineer - in - Charge.

Providing and fixing prelaminated sheet three layer medium density (exterior grade) particle board grade - I type - II confirming IS 12823 bonded with phenol formaldehyde synthetic resin of approved brand and manufacture in panelling fixed in Aluminium doors, wndows, shutters and partition frames with CP brass / stain less steel screws etc. complete as per architectural drawings and direction of Engineer - in- Charge.

Providing and fixing glazing in Al. doors and windows ventilaor shutters and partitions etc. with PVC / neosprene gasket with CP brass / stain less steel screws etc. complete as per architectural drawings and direction of Engineer - in- Charge.

Providing and laying plaster of paris putty of 2mm thick over plastered surface to prepare the surface even and smooth all complete:

Providing and Providing and painting with plastic Emulsion paints two or more coats on New surface of required shade to give an even shade including brushing the surface clean of all dirt dust and smoothened by sand paper etc complete. Internal Wall Surface

Providing and Providing and painting with acrylic exterior paints of quality and make equivalent to EXCEL, WEATHER SHIELD to give an even shade including brushing the surface clean of dirt, dust etc and sand papering and filling the scratches complete on New surface. External Wall

Supplying, fabricating, fitting and fixing tubular truss including putty, hoisting, fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shape washer etc complete in curve shaped Sikkim- style roofing as per the standard specification and design and as per the direction of Engineer - in- Charge all complete.

Providing, fitting, fixing of 24 BWG GP sheet roofing by making corrugation of 50mmx50mm x50mm on both side with G.I. hooks, bolts and nut 8mm dia with bitumen, GI limpet washers filled with white bad including coat of approved steel primer and two coats of approved paint, on overlapping of sheet excluding carriage all complete.

Providing fitting fixing ridges or hips of 60cm overall width of plain 24 BWG Pre-painted HULAS Sheet fixed with G.I, J or L hooks bolts and nuts 8mm dia Limpets, Bitumen washers complete.

Providing, fitting and fixing 23cm deep 24BWG Pre-painted HULAS. sheet eaves board including (50mmx25mm) dressed sal timber beading and M.S. Rod brackets all complete.

Providing & fixing 15cm wide 45cm overall semicircular prepainted (HULLAS) sheet (Class I) gutter with iron brackets 40x3mm size, boltsfilled with epoxy in each bolts, nuts (8 to 10 gm per bolt), washers etc including making, connection with rain water pipes.

Providing and fixing M.S round or square bars at required spacing in timber frames of windows as per the direction of Engineer - in- Charge all complete.

Providing and applying priming coat with ready mixed Red oxide, Zinc chromate primer on steel / galvanized Iron steel works including preparation of the surface complete.

Providing and painting with ready mixed paint of approved quality and shade with two or more coats to give an even and smooth shade including clearing the surface complete on new surface.

Providing box drain of 60 cm (ht) x 45 cm (width) of internal dimension with 1:2:4 Plum concrete (40mm & down) side wall thickness of 23 cm (hill side) and 30 cm (road side) with1:3:6 (20 mm & down) base concrete of thickness of 15 cm with standard specification over 15 cm stone soling including providing & laying guard stones, complete as per the direction of the Engineer-in-Charge.

Stone tile 8mm thick (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete.

Granite of any colour and shade

Providing and fixing M.S grills in timber frames of windows with M.S flats with nuts, bolts, and smooth finishing of welded joints/surface with Grills weighing 8.00Kg/sqm as per the direction of Engineer - in- Charge all complete

Cost of Haulage Excluding Loading and Unloading of stock material within 120 km all complete.

Loading and Unloading of Cement or Steel by Manual Means and Stacking.

Cost of Haulage Excluding Loading and Unloading of Sand within 50 km all complete.

Cost of Haulage Excluding Loading and Unloading of Stone chips within 50 km all complete.

Cost of Haulage Excluding Loading and Unloading of Stone within 50 km all complete.

Loading and Unloading of Stone Boulder/Stone aggregates/Sand/Kanker/Moorum.

Haulage for throwing away of excavated earth via Surfaced Road for the distance of 30 km excluding loading and unloading all complete.

NON-SOR ITEMS

[MED1] HPCL Automatic hermetically Sealed Door Size 1500mm*2100mm - 60mm thick (4mm HPCL+52mm CFC Puff+), Lever Handle, vision glass 350mm*350mm, sliding track, Canopy (PCGI)& Plank (MICA) Wall covering for standard wall width 400mm. AUTOMATION Clarification for Sliding Door: - •Pack of Automation contains One Electric Controller. •One Motor, One Encoder/Return Pulley. •One Set of Photo Cells & Two Magic Switches. •Two Foot Switches. One Teeth Belt

BOUNDARY FENCING

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Providing and Laying in position cement concrete of specified grade including compacting curing etc all complete. 1:3:6 mix. (1 cement, 3 coarse sand, 6 stone aggregate of 20mm & down size)

Filling inside plinth in building works with 23cm layers, consolidated to 15cm including watering, ramming etc, all complete.

Providing, fixing & removing form work for casting R.C.C items as indicated below: with locally available timber)

Plinth Beam/tie

Columns

Providing and Laying in position specified grade of reinforced cement concrete excluding the cost of form work, finishing and reinforcements.1:1.5:3 Mix (1cement, 1.5 coarse sand 3 graded stone aggregate 20mm and down nominal gauge)

Supplying, bending and placing in position tor steel reinforcement in all R.C.C works including cost of binding wires, all complete.

Providing and laying first class brick work in half brick thick in superstructure of standard size bricks with 1:4 cement mortar (1 cement and 4 course sand) including carriage of bricks up to work site, curing etc all complete.

Providing and Laying 12mm thick cement plaster of specified mix in single coat including finishing even and smooth and curing complete. 1:3 Mix

Providing and Providing and painting with acrylic exterior paints of quality and make equivalent to EXCEL, WEATHER SHIELD to give an even shade including brushing the surface clean of dirt, dust etc and sand papering and filling the scratches complete on New surface

G.I Barbed wire Fencing 1.8 metre high (Providing and fixing 1.8 metres high GI barbed wire fencing with 2.4 m angle iron posts 50 mm x 50 mm x 6 mm placed every 3 metres center to center founded in M15 grade cement concrete, 0.6 metre below ground level, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with 12 horizontal lines and 2 diagonals interwoven with horizontal wires, fixed with GI staples, turn buckles etc complete as per clause 807 )

Cost of Haulage Excluding Loading and Unloading of stock material within 120 km all complete.

Loading and Unloading of Cement or Steel by Manual Means and Stacking.

Cost of Haulage Excluding Loading and Unloading of Sand within 50 km all complete.

Cost of Haulage Excluding Loading and Unloading of Stone chips within 50 km all complete.

Cost of Haulage Excluding Loading and Unloading of Stone within 50 km all complete.

Loading and Unloading of Stone Boulder/Stone aggregates/Sand/Kanker/Moorum.

Haulage for throwing away of excavated earth via Surfaced Road for the distance of 30 km excluding loading and unloading all complete.

PROTECTIVE WORK

Excavation in soil in hilly area by mechanical means including cutting and trimming of side slopes and disposing of excavated earth with all lifts and lead upto 1000 metres.

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Providing & Laying in position cement concrete of 1:3:6 mix. (1 cement, 3 coarse sand, 6 stone aggregate of 20mm & down size) including compacting curing etc. all complete.

Providing and Laying Plum concrete in 1:2:4 c.c. (1cement, 2coarse sand, 4clean hard graded stone chips of 20 mm down nominal gauge) with 70% clean hard stone of sizes not exceeding 15cm including shuttering, compacting and curing complete, as per the direction of Engineer in Charge.

Providing weep holes in Brick masonry/Plain/Reinforced concrete abutment, wing wall/return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical specifications

Cost of Haulage Excluding Loading and Unloading of stock material within 120 km all complete.

Loading and Unloading of Cement by Manual Means and Stacking.

Cost of Haulage Excluding Loading and Unloading of Sand within 50 km all complete.

Cost of Haulage Excluding Loading and Unloading of Stone chips within 50 km all complete.

Cost of Haulage Excluding Loading and Unloading of Stone within 50 km all complete.

Loading and Unloading of Stone Boulder/Stone aggregates/Sand/Kanker/Moorum.

Haulage for throwing away of excavated earth via Surfaced Road for the distance of 20 km excluding loading and unloading all complete.

INTERNAL AND EXTERNAL ELECTRIFICATION WORKS

INTERNAL ELECTRIFICATION WORK.

SECTION A

Wiring With PVC Insulated (HR FRLS) Copper Conductor Single Core Cable in Best Quality Recessed Alathine Pipe

Wiring for light/Fan/Call bell & 6 A plug point with 2x1.5 sqmm FRLSH PVC insulated copper conductor single core cable in best quality recessed alkathine pipe and earthing the point with 1x 1.5 sqmm HR FRLS PVC insulated copper conductor single core cable as required.

Wiring for 16 A plug point with 2x 2.5 sqmm FRLSH PVC insulated copper conductor single core cable in best quality recessed alkathine pipe and earthing the point with 1x 2.5 sqmm FRLSH PVC insulated copper conductor single core cable as required.

Wiring for sub-main for light/fan/call bell & 6 amps plug points with 2x 2.5 sqmm FRLSH PVC insulated copper conductor single core cable in best quality recessed alkathine pipe and earthing the point with 1x2.5 sqmm FRLSH PVC insulated copper conductor single core cable as required.

Wiring for sub-main for 25 amps (2x1000W) plug points with 2x4.0 sqmm FRLSH PVC insulated copper conductor single core cable in best quality recessed alkathine pipe and earthing the point with 1x4.0 sqmm FRLSH PVC insulated copper conductor single core cable as required.

SECTION B

Switch, Socket and Accessories

Supplying & fixing 06 amps 1 way FT switch on white moduler plate and metal flux box including connection etc. as required.

(a)1 no. 06 amps FT switch with 1 no white 1 moduler plate and 1 moduler metal flux box.

(b)2 no. 06 amps FT switch with 1 no white 2 moduler plate and 2 moduler metal flux box.

(c)3 no. 06 amps FT switch with 1 no white 3 moduler plate and 3 moduler metal flux box.

(d)4 no. 06 amps FT switch with 1 no white 4 moduler plate and 4 moduler metal flux box.

(e)6 no. 06 amps FT switch with 1 no white 6 moduler plate and 6 moduler metal flux box.

(f)8 no. 06 amps FT switch with 1 no white 8 moduler plate and 8 moduler metal flux box.

Supplying & fixing 1 no. 2 way switch with 1 no 1module white plate & 1 no 1 module metal flux box including connection etc. as required.

Supplying & fixing 1 no. fan step regulator 120 watts, 1 no. white plate (2 module) and 1 no. (2 module) metal flux box including connection etc. as required.

Supplying & fixing Metal Enclosure with 160A FP MCCB

Supplying & fixing Metal plug & socket DB's 63A FP 3P+N+ E

Supplying & fixing Metal plug & socket DB's 32A FP 3P+N+ E

Supplying & fixing Metal plug & socket DB's 32A DP+E

Supplying & fixing 1no. 20 amps socket & 1 no. 20 amps switch with 1 no, 3 module white plate & 1 no. 3 module metal flush box including connection etc. as required.

Supplying & fixing 1 no. 16 amps socket, & 16 amps switch,white plate (3 module) & Metal flux box (3 module) including connection etc. as required.

Supplying & fixing 2 no. 16 amps socket, & 2 no.16 amps switch,white plate (6 module) & Metal flux box (6 module) including connection etc. as required.

Supplying & fixing 1 no. 06 amps socket with 1no. 06 amps switch, 1 no. 3 module white plate & 1 no. 3 module metal flux box ) including connection etc. as required.

Supplying & fixing 2 no. 06 amps socket & 2 no. 06 amps switch with 1 no, 6 module white plate & 1 no. 6 module metal flush boxincluding connection etc. as required.

Supplying & fixing 1 no RJ45 data socket with 1 no, 1 module white plate & 1 no. 1 module metal flush box including connection etc. as required.

Supplying & fixing 2 no RJ45 data socket with 1 no,2 module white plate & 1no.2 module metal flush box including connection etc. as required.

Supplying & fixing 1 no RJ11 tele socket with 1 no, 1 module white plate & 1 no. 1 module metal flush box including connection etc. as required.

SECTION C

Light Fitting & Accessories

Supplying & fixing recessed mounted LED panel light fitting 2ft x 2ft 36 watts including connection etc. as required.

Supplying & fixing recessed LED fitting 20 watts including connection etc. as required.

Supplying & fixing recessed LED fitting 9 watts including connection etc. as required.

Supplying & fixing Ceiling Fan 1200mm with complete accessories including connection as required.

Supplying & fixing Angle/Batten holder with 9 watts LED lamp including connection etc. as required.

Supplying & fixing LED wall mounting mirror light including connection etc. as required.

Supplying, Installation, testing & commissioning of ventilating fan 250mm including connection as required.

Supplying, Installation, testing & commissioning of ceiling mounted ventilating fan including connection as required.

SECTION D

Earthing and Lightning Conductor

Supply, Installation, Testing and Commissioning of GI Chemical earthing electrode, cristiline conducting material filled, 2Mtr. long PIP technology inner dia 42.2mm & outer da 76.2mm, placed with 50 Kg. back filled compound mixed with equal quantity of black garden soil replacing the excavated earth including excavation in any kind of soil complete in all respect. Earth pit cover (High grade PVC, Circular, high compressive strength, impact resistant and high heat resistant)

Supply, Installation, Testing and Commissioning of Copper bonded Chemical earthing electrode, cristiline conducting material filled, 3Mtr. long, 75 mm dia placed with 50 Kg. back filled compound mixed with equal quantity of black garden soil replacing the excavated earth including excavation in any kind of soil complete in all respect. Earth pit cover (High grade PVC, Circular, high compressive strength, impact resistant and high heat resistant)

Supply errection testing and commissioning of conventional solid copper air terminal prong 1.5 mtrs long, with threaded type copper ball, finials and base plate complete in all respect.

Supply & laying of Copper / GI / Aluminium earthing strips for connecting the earthing electrodes with the electrical installations / systems / distribution boxes etc, with all fixing accessorieson and placing walls / trenches / ceiling / directly burried in earth as per specification and requirement. All earth strips burried in eatrh will be provided with protective non bio degradable PVC sleevesaccording to the size of conductor. Test certificate of all kind of strips shall be produced by the vendor during supply.

25 x 6 mm 99% electrolytic grade copper strip

50 x 6 mm G I hot deep galvanised strip 80-100 microne

40 x 6 mm GI hot deep galvanised strip 80-100 microne

25 x 6mm GI hot deep galvanised strip 80-100 microne

10 SWG CU WIRE

EARTH PIT COVER

Earth pit cover (High grade PVC, Circular, high compressive strength, impact resistant and high heat resistant)

SECTION E

Panels and Distribution boxes

Supplying & installation testing and commissioning of MCCB/MCB distribution board Double Door/Single door (CONFORMING TO CPWD /NBC/ Relevant IS & BIS Code)

Vertical TPN DB 8 way MCCB)

Vertical TPN DB 6 way MCCB)

Vertical TPN DB 4 way MCCB)

TPN DB 12 way

TPN DB 8 way

TPN DB 6 way

TPN DB 4 way

SPN DB 16 way

SPN DB 12 way

SPN DB 8 way

Supplying, installation, testing & commissioning of Molded case circuit breaker (CONFORMING TO CPWD /NBC/ Relevant IS & BIS Code)

Four pole 160 Amps

Four pole 100 Amps

Supplying, installation, testing & commissioning of Residual current breaker (CONFORMING TO CPWD /NBC/ Relevant IS & BIS Code)

Double pole 40 Amps

Supplying, installation, testing & commissioning of Miniature circuit breaker (CONFORMING TO CPWD /NBC/ Relevant IS & BIS Code)

Single pole 06 Amps

Single pole 10 Amps

Single pole 16 Amps

Single pole 20 Amps

Double pole 16 Amps

Double pole 32 Amps

Triple pole 40 Amps

Triple pole 32 Amps

Triple pole 16 Amps

Four pole 40 Amps

Four pole 63 Amps

SECTION F

Laying of 1.1 kv Grade Cables

Providing & laying 1.1 KV grade XLPE insulated aluminium armoured conductor cable on surface of the wall of building with required size of aluminium shadle and screw etc. as required.

3.5 Core 120 Sqmm Cable

3.5 Core 95 Sqmm Cable

3.5 Core 35 Sqmm Cable

4 Core 10 Sqmm Cable

4 Core 16 Sqmm Cable

Providing & laying 1.1 KV grade XLPE insulated copper armoured conductor cable on surface of the wall of building with required size of aluminium shadle and screw etc. as required.

1 Core 35 Sqmm Cable Cu Ar

4 Core 4 Sqmm Cable Cu Ar

4 Core 6 Sqmm Cable Cu Ar

3 Core 4 Sqmm Cable (Un Ar)

Termination of cable 3.5 core / 4 core armoured Aluminium cable with required aluminium lugs and compression glands for each end complete in all respect including connection.

3.5 Core120 Sqmm Cable

3.5 Core 95 Sqmm Cable

3.5 Core 35 Sqmm Cable

4 Core 10 Sqmm Cable

4 Core 16 Sqmm Cable

Termination of cable 3 core / 4 core armoured copper cable with required copper lugs and compression glands for each end complete in all respect including connection.

1 Core 35 Sqmm Cable Cu Ar

3 Core 4.0 Sqmm Cable Cu Ar

4 Core 4 Sqmm Cable Cu Ar

4 Core 6 Sqmm Cable Cu Ar

SECTION G

Main Panels

MAIN LT CUM DG AMF CONTROLLER PANEL Incomer: 400A 4 Pole 36kA MCCB with Microprocessor Based with O/C, S/C, E/F Release-2No. Outgoing Feeder: 160A 4Pole 25kA MCCB -2nos.,125A 4Pole 25kA MCCB- 2nos.,100A 4Pole 25kA MCCB- 3nos., 63A 4Pole 10kA MCB-4nos., 40A 4Pole 10kA MCB-7nos., 32A 4Pole 10kA MCB - 8nos.

OT - AHU & ODU Panel Incomer: 100A 4 Pole 25kA MCCB with Microprocessor Based with O/C, S/C, E/F Release-1No. Outgoing Feeder: 40A 4Pole 10kA MCB + 40A 100mA RCCB -10nos.,25A 4Pole 10kA MCB + 25A 100mA RCCB - 8nos.

Fire Panel :

400A 3 Pole 36kA MCCB with MP Based with O/C, S/C Release -- 1No. …. Incomer

Spreader, Extended Rotary Handle, Aux. & Trip Contact

Indicating Lamp -- 6 Nos.

CT, ratio : 400/5A, Class - 1, VA-15 ---- 1Set

Digital Ammeter -- 1No.

Digital Voltmeter -- 1No.

6A FP Miniature Circuit Breaker, 10kA --- 1No.

6A DP Miniature Circuit Breaker, 10kA --- 1 No.

Hooter - 1No.

Outgoing Feeder :

55kW Star-Delta Starter for Sprinkler Pump : 1No. Consist of

160A TP 25kA Thermal based O/C & S/C MCCB with Spreader, Extended Rotary Handle, Aux. & Trip Contact -1 No.

80A AC3 TP Power Contactor : 2Nos.

65A AC3 TP Power Contactor : 1No.

Over Load Relay ( 48 - 65A )

LED Lamp - 3Nos.

Push Button - 2Nos.

55kW Star-Delta Starter for Hydrant Pump : 1No. Consist of

160A TP 25kA Thermal based O/C & S/C MCCB with Spreader, Extended Rotary Handle, Aux. & Trip Contact -1 No.

80A AC3 TP Power Contactor : 2Nos.

65A AC3 TP Power Contactor : 1No.

Over Load Relay ( 48 - 65A )

LED Lamp - 3Nos.

Push Button - 2Nos.

55kW Diesel Pump for Standby Operation : 1No. Consist of

Battery Charger - 1No.

Push Button - 2Nos.

Voltage Monitoring Relay - 1No.

Cranking Relay - 1No.

Auxiliary Contactor - 1 Lot.

Control MCB - 1 Lot.

Timer - 1 Lot.

11kW Star-Delta Starter for Jockey Pump : 2Nos. Consist of

40A TP 25kA Thermal based O/C & S/C MCCB with Spreader, Extended Rotary Handle, Aux. & Trip Contact -2 Nos.

25A AC3 TP Power Contactor : 4Nos.

12A AC3 TP Power Contactor : 2Nos.

Over Load Relay ( 9 - 13A ) : 2Nos

LED Lamp - 6Nos.

Push Button - 4Nos.

Hooter - 2Nos.

Consider auxiliary Contactor, Timer for each outgoing feeder as per logic requirement.

Indicating Lamp -- 1 Lot.

6A DP Miniature Circuit Breaker, 10kA --- 1 No.

100kVAr APFC Panel :

250A 3 Pole 36kA MCCB with Microprocessor Based with O/C, S/C, -- 1No. …. Incomer

Indicating Lamp -- 6Nos.

CT, ratio : 400/5A, Class - 1, VA-15 ---- 1Set

Digital Ammeter & Voltmeter

6A FP Miniature Circuit Breaker, 10kA --- 1No.

6A DP Miniature Circuit Breaker, 10kA --- 3 Nos.

08 Step APFC Controller -1 no

Auxiliary Contactor 230V AC - 1Lot

Louvers & Fan - 1Lot

25kVAr Capacitor Feeder : 2nos.

10kVAr Capacitor Feeder : 4nos.

5kVAr Capacitor Feeder : 4no.

VRF ODU Panel Incomer: 100A 4 Pole 25kA MCCB with Microprocessor Based with O/C, S/C, E/F Release-1No. Outgoing Feeder: 40A 4Pole 10kA MCB -4nos.,40A 4Pole 100mA RCCB- 6nos.

SECTION H

Supporting items

Supplying, installation, testing & commissioning of 2 x 20kVA UPS system for Parallel Redundancy Mode Three Phase Input and Single Phase Output

Supplying, installation, testing & commissioning of 2 x 05kVA UPS system for Parallel Redundancy Mode Single Phase Input and Single Phase Output

SECTION I

Lift Shaft Wiring.

Supplying, installation, testing & commissioning of the following:

Wiring for 6 lights controlled by existing MCBs in lift panel in lift machine room.

Wiring for 6 Nos. of 16 Amps 3 pin socket with switch provided one number at each floor, controlled by the existing MCBs in lift panel.

Providing 6 Nos. bulk head light fitting (surface mounting) with 7 Watt LED lamp.

Providing 1 No 12 way SPN DB with 32 A 4P MCB + 20 A 2P MCB + 16 A SP MCB + 10 A SP MCB complete .

Providing 1 No 12 way SPN DB with 32 A 2P MCB + 16 A SP MCB + 10 A SP MCB complete .

SECTION J

Cable Tray

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc.as required

a) 100 mm width X 50 mm depth X 1.6 mm thickness

b) 150 mm width X 50 mm depth X 1.6 mm thickness

c) 300 mm width X 50 mm depth X 1.6 mm thickness

EXTERNAL ELECTRIFICATION WORK

SECTION K

Sub Station

Supply and erection of MS Swaged Type steel tubular pole as per Standard IS: 2713 ( Pat-I and III): 1980 as amended upto date, 410 SP 39 overall length 9 meters , planting depth 1.5 meters, above ground 7.5 meters , effective length of Each section. Bottom 5.0 meters, Middle 2.0 meters, Top 2.0 meters. Outside diameter and Thickness of each Section. Bottom 165.1x 5.40 mm, Middle 139.7x 4.50 mm, Top 114.3x 3.65 mm . Joint Length ( in cm.) Bottom 30 cm. Top 30 cm. Approximate weight of Pole 170 Kg. Point of application of load below/top (mtr.) 0.35 mtr. Breaking load ( in Kgf ) 478. Working load with factor of Safety : 2.5 ( in Kgf ) 210. Crippling load ( in Kgf ) 339 . Complete with MS base plate of 6mm thick and earthing slot. The rate should include painting the pole with two coats of red-oxide primer of approved brand and erection by digging pit (0.6x0.6x1.5M) and concreeting with 1:4:8 cc up to 400 mm above ground level, stay set etc as required complete in all respect. (Make: ISI Standards with test certificate)

Cross arm made with 100x50x6mm MS Channel 2.30 Mtrs long with fixing clamps, nuts bolts etc for mounting SA, DISC, PIN, GOABS and DO etc. complete in all respect.

Horizontal member 2.30 mtrs

Cross member 3.10 mtrs

Gang operated Air Break Switch 11 KV TP 400 Amps Heavy duty as per IS 9920 & 9921 complete with all fittings.and test certificate. ABI/Mayur/Rex/ Eqv

Drope out fuse unit 11 KV TP 400 Amps heavy duty as per IS 9385 complete with all fittings.and test certificate. ABI/Mayur/Rex/ Eqv

9 KV,5 KA single pole unit Metal Oxide gapless Surge Arrestor for 11KV, 50c/s solidly earthed neutral system confirming to IS:3070 (part 3) Raychem RPG make or equivalent

11 KV 10 KN Pin insulator with Pin complete in all respect with spindle.and test certificate. ABI/Mayur/Rex/ Eqv

11 KV Disc Insulator 45KN two disc per set with H/W fittings complete in all respect and test certificate. ABI/Mayur/Rex/ Eqv

ACSR 'DOG" Conductor 100 sq mm

Guy assembly complete with 7/10 SWG GI Stay wire, 140x85 mm HT Guy insulator,18 mm dia stay rod 1.8 mtrs.long wiuth bow thimble,turn buckle and 300 x 300 x 6 mm anchor plate

Red oxide primer and Aluminium Paints for two poles

Danger Notice Plate 11 KV

Danger Notice Plate 440 V

Supply and fixing in position 900MM wide 12MM thick rubber matting of 11KV grade as per electricity rules. Along with test certificate.

H.T. PANEL

Supply of Indoor type, factory assembled, metal clad, fully insulated, totally enclosed 11 kV Incoming & Outgoing Panel with, 11kV, 630A, 26.3kA for 1 sec Drawout type VCB with Motorised spring charge Mechanism suitable for 240V AC, Closing & Tripping Coils rated 110V DC, 6NO + 6NC, Aux switch, Copper Bus Bar complete in all respect conforming to latest IS CPRI approved.

INCOMER

ONE(1)-Electrically drawout type 630A, 11kV, 26.3kA for 1 Sec VCB

Epoxy cast Dual Core CT - 50- 25/ 5-5A; Core 1: 10VA for metering, class - 1 ;Core 2 -15VA for protection, class-5P10

LINE P.T with primary fuse- One set of 3nos.1 phase PTs with ratio 11000/√3 /110/√3, Class 1.0 / 3P, 50VA/50VA/Ph

Breaker ON/OFF/TRIP/SpringCharge/TRIP Circuit Healthy

One-(1)- EMERGENCY TRIP Push button

One-(1)- RELAY Reset Push button

R-­‐Ph/Y-­‐Ph/B-­‐Ph Indication

Digital Ammeter

Digital Voltmeter

Bi-directional Energy Meter Connection & Fixing provision ( Scope of supply Electricty Board )

1 no. - Master Trip Relay .

1 No. - Numerical Type Over Current & Earth Fault Relay

1 No. - Trip Circuit Supervision Relay.

1 No - Annunciator ( 12 Window) with Hooter Units.

1 No. - Earth Bus Bars and all other accessories.

Altitude- 2000Mtr

SECTION L

Transformer

Supply, installation, testing ,commissioning of 315kVA, 11kV/433V Oil Type Outdoor Transformer complete in all respect with the following accessories and latest specification.This specification covers design, manufacture, assembly, testing at manufacturer's works, supply & delivery of three phase 50 HZ, 11kV/0.433 V, Delta/Star, Vector Group Dyn11, two winding, outdoor type, oil immersed naturally Oil & Air cooled, Stack Core, non sealed type Distribution Transformer with Outdoor Bushing and cable End Box at both ends .The transformers covered by this specification shall, unless otherwise specified be built to confirm to the latest Indian Electricity Rules, wherever applicable and the requirements of the latest issues of IS: 1180 (Part-I), CBIP Standards and other ISS (All as per latest isuses for level-II)

Cooling type : ONAN

Vector Group : Dyn11

Winding Material : Copper

Marshalling Box

OTI with alarm & trip Contact

WTI with alarm and trip Contact

Buchholz Relay with alarm and trip Contact

Shut off valves for Buchholz Relay

Magnetic Oil Level guage

SECTION M

Diesel Generator

Supply, installation, testing ,commissioning of Diesel generator set 320 KVA prime rating radiator cooled with alternator of 320 kVA output, 3 Phase, 415 V, 50 c/s 0.8 p. f. A.C a totally enclosed liquid cooled multi- cylinder (6/12) in-line 4 stroke, radiator cooled diesel engine developing suitable BHP at 1500 rpm, along with standard accessories, ƒBrushless type, Screen protected, Revolving field, Self excited alternator with static excitation system running at 1500 RPM.

SECTION N

External Cables

Providing & laying 11 KV grade XLPE insulated aluminium armoured conductor cable on surface of the wall of building with required size of aluminium shadle and screw etc. as required.

Copper XLPE Cables (Cu Ar)

3 Core 150 Sqmm Cable

11KV CABLE TERMINATION KIT

Supply, fixing, connection, testing & commissioning of Heat shrinkable outdoor type end termination kit for 11 KV(UE) 3 core XLPE .

Copper XLPE Cables (Cu Ar)

3 Core 150 Sqmm Cable

INTERNAL AND EXTERNAL PLUMBING WORKS

INTERNAL SANITARY FIXTURES

Providing, fitting and fixing white vitreous china pedestal (European type) water closet (W.C) pan with seat and lid, with C.P. brass hinges, 10ltr low level cistern with fittings and brackets 40mm flush bend, 20mm overflow pipe with specials, including Providing and painting and making good the wall and floors as required all complete: W.C. pan European One pice (Ivory) CAT NO 92008/ Eqv.

Supplying Installing, testing and commissioning of round / rectangle white colour glazed wash basin under counter type with 32 mm dia waste coupling half thread with 80mm height, CP bottle trap with extention pipe, 15 mm CP 450 mm long CP inlet connection pipe, CP wall flange all of approved make etc, complete in all respect.(Oval wash basin/Round wash Basin)

Providing, Fitting and fixing Chromium plated fittings of approved quality and size complete: Basin Mixer

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fitting chromium plated toilet paper holder including the making holes and fixed to timber cleats with CP screws washer etc. all complete:.

Providing, fitting and fixing Beveled gauge mirror of superior glass with 6mm A.C. sheets ground and fixed to timber cleats with CP screws, washer etc complete.

Providing, fitting and fixing. of chromium plated soap dish with necessary screw etc all complete.

Supplying, fixing and testing uPVC Multi floor trap along with SS frame & cover (125 mm x 125 mm square / 100mm round). Trap of 100 mm dia. Inlet and 75 mm dia outlet fixed on a bed of cement concrete etc., complete in all respect. (The frame and grating shall be approved by Architects)

Supplying, fixing and testing uPVC P trap along with SS frame & cover (125 mm x 125 mm square / 100mm round). Trap of 100 mm dia. Inlet and 75 mm dia outlet fixed on a bed of cement concrete etc., complete in all respect. (The frame and grating shall be approved by Architects)

Fixing CP brass LONG body bib cock including, necessary flange, cutting and making good he walls / floors wherever required complete.

Fixing CP brass LONG body bib cock including, necessary flange, cutting and making good he walls / floors wherever required complete.

Providing, fitting and fixing towel ring of chromium plated brass complete with CP brass screw and timber cleats.

Providing, Fitting and Fixing C.P. Brass Double coat Hooks with CP screws.

providing fixing stain less steel kitchen sink with CI brackets, CP brass chain with rubber plug 40mm CP brass waste, CP brass tap etc complete i/c the fittings, cuttings and making good the wall wherever required. (610mm x450mm x200mm)

Supplying,Installing, testing and commissioning of surgucal scrub station with auto sensor, 1nos auto taps. Infra Ray photo sensors, Hydro Teflon Solenoids and soup dispenser. Hot Water Geiger 8 ltrs, Hydro polyester pump 0.5HP Hand washing Soft Shower, Electronic Circuits & Controller. (SINK SIZE - 32"L X 20"W X 18"D)

Supplying,Installing, testing and commissioning of SS Wash Sink 02 Bay two tab one outlet Approx size 40”LX24”WX20”H wall mounted made of 1.2 mm SS sheet 304 grade with Jaguar fittings with detachable SS sliding perforated tray .

Installing, testing and commissioningg grab bar 692mm long, white including neccesary fixing materials etc, complete in all respect.

Installing, testing and commissioningg grab bar vertical swing, white including neccesary fixing materials etc, complete in all respect.

Supplying ,Installing, testing and commissioning of fully automatic "NO TOUCH" stainless steel finish hand drier suitable to operate on 220 volts, single phase 50 hz, A.C. power supply and directly plugged to power point complete.

Supplying ,Installing, testing and commissioning of SS 304 Grade bend pan sink with cistern, angles valve, hand shower, shower nozzle, braclets etc, complete in all respect.

SOIL, WASTE, AND RAIN WATER PIPES

Supplying, fitting fixing and testing SWR soil and waste pipes confirming to IS 13592, type B solvent fit (confirming to IS 5382) joint inclusive of all necessary fittings like bends, tees, offsets, door bends, junctions, cowls, etc., laid under floor/ fixed on walls on G.I. brackets with GI 'U' clamps in pipe shafts etc., complete in all respect.

a) 110 mm dia

b) 75 mm dia

Supplying, fitting fixing and testing SWR soil, waste pipes confirming to IS 13592 type B with rubber ring (confirming to IS 5382) with solvent joint inclusive of all necessary fittings like bends 45 or 90 degree, 'Y's, tees, offsets, door bends, junctions, screw type caps, vent cowl etc., fixed in the pipe shafts on pipe racks. complete in all respect.

a) 110mm dia

Supplying,fitting fixing and testing uPVC UV-R pressure pipe (6 Kg/ sq cm) confirming to IS 4985 : 2000 for waste connection from wash basin, kitchen sinks and urinal to floor trap/ anti syphonage pipe with solvent fit joints, including all the fittings, laid under floor/concealed in wall etc, the work shall include wall chase and making good the same in cement mortar etc, complete in all respect.

a) 50 mm dia

Supplying, fitting fixing and testing SWR rain water pipes with all fittings like shoes, bends fixed in the pipe shafts (ducts) with suitable supports etc., complete in all respect.

a) 110 mm dia - Type - A

Supplying, fitting fixing and testing Roof Corner Trap with suitable supports etc., complete in all respect.

a) 110 mm dia

WATER SUPPLY SYSTEM

(CPVC) up to 50 mm dia SDR.11

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall

a)20 mm nominal outer dia Pipes

b)25 mm nominal outer dia Pipes

c)32 mm nominal outer dia Pipes

d)40 mm nominal outer dia Pipes

Supplying, installing and testing approved make full way lever operated CPVC ball valves conforming to ASTM D 2846 with unions etc.Complete in all respect.

a) 20 mm dia

b) 25 mm dia

c) 32 mm dia

d)40 mm dia

e)50 mm dia

EXTERNAL SEWERAGE SYSTEM

Excavation in soil in hilly area by manual means including cutting and trimming of side slopes and disposing of excavated earth with all lifts and lead upto 50 metres.

Supplying, fixing, testing and commissioning precast gully traps, 300X300mm pvc grating (medium duty), 100 mm dia outlet set in PCC 1:4:8 bed, 125 thick masonry chamber in CM 1:4, internal and external plastering 12mm thick in CM 1:6, necessary earthwork, C.I. cover medium duty weighing 12Kgs. etc., complete in all respect. as directed by the Engineer in charge.

Providing and constructing Inspection chambers using 125mm thick burnt brick masonry walls built in CM 1:4 over PCC 1:4:8 bed ,RCC cover slab, benching in CC 1:2:4 internal faces plastered smooth in CM 1:4, 15mm thick and outside exposed faces with cm 1:6 15mm thick including 600x600mm medium duty CI Manhole Frame & cover with necessary earth work excavation and backfilling and disposing surplus soil as directed by the Engineer in charge etc., complete in all respect.

a) 450x500mm size internal & depth upto 600mm

b) 500x500mm dia size internal & depth upto 600mm

a) 170 mm dia

EXTERNAL WATER SUPPLY SYSTEM

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

a) 50 mm nominal outer dia Pipes

PVC TANK DETAILES

Providing and placing on terrace high density polyethylene water storage tank with man hole lid and suitable locking arrangement including making holes for inlet, out let and ball cock including testing etc. all complete: (Sintex or equivalent) 2000 Itrs capacity

SEWAGE TREATMENT PLANT

Design & engineering, supply, erection, testing and commissioning of 30 CUM/DAY, Prefabricated Sewage treatment plant including all mechanical & electrical equipment, supervision of civil works at site with performance guarantee of different capacities as required. The treatment process shall be based on Fluidised Bed Aerobic Bio Reactor or Moving Bed Bio Reactor with diffused aeration system followed by Proper Settling Process along with Tertiary Filtration Unit.

REVERSE OSMOSIS SYSTEM.

100LPH RO Plant with Mix Bed

Low Pressure Feed pumps - Horizontal Multistage, Centrifugal type; With Motor-Base Frame-MOC-CI Base+ Suction-Discharge Manifold & Internal Chamber-SS304+ Shaft - SS316. Flow- 500 - 600 LPH & Head 25 - 35 Mtrs.2 Nos. pump (1 working+1 standby), cascade operation, approx 0.5kw each, located at adjecent to WTP. Both the pumps shall be equal running hours for proper use controlled by intellegent control panel with all protection.

Providing, fixing, testing and commissioning of vertical self supporting multi grade filter, in FRP vessels 250 mm dia approx, filtration rate 18.0 m3/hr/m2) approx. Pressure gauges at inlet & outlet, sample cock, Manual Multiport valve and all accessories, with initial charge of filter media for multi-grade filter, complete. (Vendor has the responsibility to check the quality of water from actual water analysis report before procuring the equipments)

Providing, fixing, testing & commissioning of metering pump type chemical doser with 100/200 lits.HDPE/ FRP solution tank, injection fitting assembly, suction and delivery hose upto the point of injection, capacity 0-5 lph, complete in all respects for treated water tank. (Chemical- NaOCL + Na2S2O5 + Antiscalent and process of dosing to be furnished by the vendor as per design and requirement)

Fully automated SS/MS Skid Mounted FRP/SS 1pass RO Block Consisting of Vertical High Pressure SS316-Pump/Pass (600LPH @ 10-13Kg/Cm2- SS316-3ph- 1 Hp approx) / Cartidge Filter + LPS + HPS + 3nos - 4" Membbrene Housing- Vertical (FRP/SS) + 4" RO Membrane 6 nos, All interconnecting Pipeline SS304, Hi pressure pipe SS304 + Automatic Flushing System with Solenoid Valve + Required Arrangement for CIP. The System is complete with Automatic Control Panel with PERMEATE/REJECT Water Rotameter/LED Display- TDS+Conductivity/Auto- Manual Option,- 500 LPH UV Sterilizer with INDEX MONITOR.

MSRL/FRP/SS Mix Bed vessel 200 dia approx, service flow rate 15 m3/hr/m2, two type(Cataion & Anioan) resin inspection glass multiport valve operated caustic HCL different suction line air injected line, water rotameter, LED display TDS/Conductivity, LED display pH, Comlete with Suitable AIR BLOWER for Proper Mixing of Resin. (Vendor has the responsibility to check the quality of water from actual water analysis report before procuring the equipments)

Mix Bed Feed pumps - Horizontal Multistage, Centrifugal type; With Motor-Base Frame-MOC-CI Base+ Suction-Discharge Manifold & Internal Chamber-SS304+ Shaft - SS316. Flow 500 LPH & Head 25 - 35 Mtrs.2 Nos. pump (1 working+1 standby), cascade operation, approx 0.5kw each, located at adjecent to WTP. Both the pumps shall be equal running hours for proper use controlled by intellegent control panel with all protection.

200Ltrs SS316 Vertical-Cylindrical Storage Tank- Proper Manhole- Drain Line- Provision for Installing SS Level Sensor.

0.45 Micron Cirtdage filter capable to flow 200 LPH

FIRE FIGHTING SYSTEM

FIRE DETECTION AND ALARM SYSTEM

Two loop Panel

Supply, erection, testing & commissioning of addressable Multi-Criteria Detector with dual optical technology and option to enable only Heat, Smoke or both detection. UL / EN approved

Supply,installation, testing & commissioning of addressable horn cum strobe complete as required. UL / EN approved

Supply,installation, testing & commissioning of addressable manual call point complete as required. UL / EN approved

Supply,installation, testing & commissioning of fault isolator complete with base as required. UL / EN approved

Supply,installation, testing & commissioning of addressable Monitor Module. UL / EN approved

Supply,installation, testing & commissioning of fire control module complete s required. UL / EN approved

Supplying & laying of 2X1.5 sqmm fire alarm armoured cable, 6000/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer seath complete as required.

2C x 1.5 mm Armoured ( loop cable)

INTERNAL FIRE RISER PIPING SYSTEM

Supplying, installation testing and commissioning of the following

Providing , laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ ceiling with suitable clamp/ support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required.

Note : The piping installation has to be put to hydraulic test to 1.5 times the working pressure & as per latest applicable code & standard before applying paint etc. complete

150mm dia

80mm dia

40mm dia

25mm dia

Supply, Installation, testing & commissioning of CI Gate Valve as per IS:14846 (PN16) with matching flanges complete with nuts & bolts.

150 mm (For riser )

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single headed Stainles Steel

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Stainless Steel (Grade 304)

Providing, fixing and testing forged brass 25 mm dia screwed inlet single acting air release valve as per IS:9890 with 25 mm dia ball valve on inlet side and pressure gauge with isolating cock.

25 mm Air Valve

Supplying & fixing 63 mm dia gun metal short branch pipe with 20mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required:

Stainless Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

EXTERNAL HYDRANT SYSTEM

Supplying, installation testing and commissioning of the following

C’ class MS ERW Pipe as per IS1239 for undegound/overground pipes with welded /flanged connection with saddles, supports (all with screwed/welded joints) as required including pipe of shorter lengths, tapering connecting pieces, short or long bends, specials like sockets, union nuts, elbows, reducers, plugs, Tees etc.Complete to make the system operative as required by LFA / TAC authorities the pipes will have to be laid and fixed in trenches. The work includes excavation in all types of soils and back filling, dewatering, etc., making holes in brick or RCC walls, slabs/ roofs and making good the damages by bringing to the original condition to the satisfaction of the Architect and painting two coats of approved shade(Post office red)of enamel paint over a coat of approved primer for over heads pipes and providing and fixing pypkote (corrosion protection tape) including supply and application of pipe coating and spiral Wrapping for underground piping (wrapping should have overlap of 15 to 20 mm) etc.

Complete as per ASTM standards/IS:10221 for corrosion protection of pipes for the under ground installation.

Note :The piping installation has to be put to hydraulic test to1.5 times the working pressure & as per latest applicable codes & standard before applying paint or pipe coating or wrapping etc. complete.

SPRINKLER SYSTEM

Supplying, installation testing and commissioning of the following

Providing , laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ ceiling with suitable clamp/ support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required.

Note : The piping installation has to be put to hydraulic test to1.5 times the working pressure & as per latest codes & standars before applying the paint

80mm dia

65mm dia

50mm dia

40mm dia

32mm dia

25mm dia

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :

Pendent Sprinkler

Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as reauired.

SITC of test & drain assembly with all 25 mm dia piping, 25 mm drain valve etc complete in all respect (TEST SPRINKLER ALONG WITH ISOLATION VALVES, SIGHT GLASS ETC & REQUIRED PIPING UPTO NEAREST DRAIN )

Test assembly

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

80mm dia

50mm dia

Supply, fixing, testing & commissioning of FLOW SWITCH as per technical specification.

80mm dia

50mm dia

Fixing Non return valve (Double plate) with matching flanges complete with nuts & bolts.

80mm dia

50mm dia

Pressure Guage with isolation clock: 0-16 kg/sq.cm (for sprinkler header)

80mm dia

50mm dia

FIRE EXTINGUISHERS

Providing & Fixing of fire extinguishers with necessary accessories, stand, trolley, etc.

Supply, erection, testing & commissioning of 4 Kg ABC (Powder Type) Fire Extinguisher. In HP Mild Steel Cylinders ISI marked fitted with pressure indicating gauge, internal discharge tube, squeeze lever type valve, discharged nozzle, suspension bracket, conforming to IS: 15683 duly charged with ABC powder (Mono Ammonium Phosphate) conforming to IS: 14609 and pressured by Nitrogen suitable for operating .on 30⁰C to + 55⁰C. (4 years maintenance free) complete in all respect.

Supply, erection, testing & commissioning of 4.5 Kg. Cap. CO2 type Fire Extinguisher (ISI marked) complete with tube horn etc.(ISI marked), handle , fixing bracket & other accessories.

Supply, erection, testing & commissioning of 9.0 litrs. Cap. Mechanical Foam Fire Extinguisher (IS: 10204 / 15397) complete with CO2 cartridge GM cap, ½ meter discharge tube & nozzle (ISI marked), handle , fixing bracket & other accessories.

Supplying and installing at approved location approved make fire buckets (3 nos./set) of 24 gauge galvanized steel sheet, standard 9 litre capacity and of round bottom shape, painted white inside and black on the bottom, inscribed with letters '' FIRE'' in black and gold with dry clean fire sand. The scope shall also include the stand for mounting the sand bucket.

SIGNAGES

Installation in position the "FIRE EXIT" Sign with luminicent colour having size 300 x 100 mm

Fixing in position the signages " FIRE ORDER" contain the following matter on 3 mm thick "Opaque" PVC foam board of computerised cut, PVC non-reflective self adhesive vinyle painted foam board of size 1200 x 1000 mm.

ALERT THE SECURITY AT SECURITY ROOM BY ACTUATING MANUAL CALL POINT LOCATED AT STRATEGIC LOCATION.

EVACUATE THE OCCUPANTS BY USING FIRE EXIT AND EMERGENCY EXITS ONLY AND ASSEMBLE AT ASSEMBLY POINTS.

BE CALM AND DO NOT GET PANIC, WALK. DO NOT RUN

IF POSSIBLE TRY TO EXTINGUISH FIRE BY USING NEAREST / SUITABLE PORTABLE EXTINGUISHER OR WATER FROM NEAREST WET RISER.

Fixing signage with printed " IN CASE OF FIRE, DO NOT USE LIFT. USE STAIRS ONLY" OF 1.5 cm height letters in red with white background. The size of the board shall be 300 x 250 mm and shaall be fixed at the height of 2 mtrs.from finished floor near Manual Call Point.

Floor identification signage ( i.e., GROUND FLOOR …etc.) at each stair enclosure on every floor, indicating the floor number in words, lettering size shall be 7.5 cm with contrasting color from back ground. Size shall be 15cm x 60cm.

CCTV/IP-PBX/WiFI/NETWORKING/HARDWARE.

Network Components (Active)

L2 Switch: Supply, Installation, Testing & Commissioning of Gigabit fixed chassis in 1RU size. Includes 24 RJ-45 10/100/1G BaseT 4x1/10 Gig SFP+ (uplink/ stacking ports , Switching capacity 51 Gb/s , Switch frame rate 41 MPPS.

L2 Switch: Supply, Installation, Testing & Commissioning of Gigabit fixed chassis in 1RU size. Includes RJ-08 10/100/1G BaseT 2x1 Gig SFP+ (uplink/ stacking ports , Switching capacity 14 Gb/s , Switch frame rate 11 MPPS.

L2 POE Switch: Supply, Installation, Testing & Commissioning of Gigabit fixed chassis in 1RU size. Includes 24 RJ-45 10/100/1G BaseT 4x1/10 Gig SFP+ (uplink/ stacking ports, should support Dual PSU , Switching capacity 51 Gb/s , Switch frame rate 41 MPPS.

SFP: Supply & Installation of SFP Single mode 1G SFP module (1310mm, 10 km., LC-LC)

SFP: Supply & Installation of SFP Single mode 10G SFP module (1310mm, 10 km., SC-LC)

Network Components (Passive)

Supply, Installation, Testing & Commissioning of Loaded LIU 12 port

Supply , Installation ,Testing & Commissioning 3 mtr LC-LC Fiber Patch Cord

Supply , Installation ,Testing & Commissioning 3 mtr SC-LC Fiber Patch Cord

Supply, Installation, Testing & Commissioning of Cat-6 24-Port UTP Loaded Toolless Patch Panel

Supply of 9U Rack :Frame/500x500 / FM / Casters T2/Glass/Metal Door, Shelf/500, PDU 1Ph, 230V, 8A, IRP Fuse - 1.8KVA, ITE / Server Rack Air Circulation module/Door Mount/ 180CFM, Horz Cable Organiser/1U/Loop, Mounting Hardware-CR (Pack of 10)

Supply of 22U Rack :Frame/480x600 / FM / Casters T2/Glass/Metal Door, Shelf/500, PDU 1Ph, 230V, 8A, IRP Fuse - 1.8KVA, ITE / Server Rack Air Circulation module/Door Mount/ 180CFM, Horz Cable Organiser/1U/Loop, Mounting Hardware-CR (Pack of 10)

Supply, Installation, Testing & Commissioning of Cat-6 1M UTP Copper Patch Cord -Colour-yellow to be used for CCTV.

Supply, Installation, Testing & Commissioning of Cat-6 1M UTP Copper Patch Cord -Colour-blue to be used for data.

Supply & Laying of 6 core armoured single mode optical fiber cable .

Supply & Laying of UTP CAT6 Cable (305 Mtr.)

IP Surveillance

Dome Camera: Supply, Installation, Testing & Commissioning of 2MP H.264/H.265 NW IR Dome Camera, 0.04Lux (Color), 0Lux (B/W, IR LED on), 2.8mm fixed lens, ONVIFS,G,T, WDR 120dB, 30fps@4MP all resolutions (H.265/H.264), H.265, H.264, MJPEG codec supported, triple streaming with full configuration, defocus detection, Directional detection, Motion detection, Tampering, crossing line, alarm in & out , Micro SD/SDHC/SDXC memory slot (Max. 128GB), IR viewable length 20m or better, PoE, CE, FCC, UL , NDAA, BIS, ROHS .

Bullet Camera: Supply, Installation, Testing & Commissioning of 2MP H.265 NW IR Bullet Camera, 0.04Lux (Color), 0Lux (B/W, IR LED on), 4mm fixed lens, ONVIFS,G,T, WDR 120dB, 30fps@5MP all resolutions (H.265/H.264), H.265, H.264, MJPEG codec supported, triple streaming with full configuration, defocus detection, Directional detection, Motion detection, Tampering, crossing line, alarm in & out , Micro SD/SDHC/SDXC memory slot (Max. 128GB), IR viewable length 30m or better, PoE, CE, FCC, UL , NDAA, BIS, ROHS .

NVR : Supply, Installation, Testing & Commissioning of 32CH NVR, support 12 megapixel camera supported, recording bandwidth 300 Mbps , 4K video out on HDMI monitor support, Dual monitor video out support, H.265, H.264, MJPEG compression support, 8 internal HDDs , e-SATA storage support, ARB & Failover (N+1) support, P2P service (QR code connect) support, CE, FCC,ROHS, UL and BIS.

Supply, Installation, Testing & Commissioning of 8 TB HDD with 7200RPM

Supply, Installation, Testing & Commissioning of 50" 4K Ultra HD Display

Supply & Installation of Wireless Mouse with Mouse Pad

Supply & Laying of HDMI cable 10 Mtr

Supply & Installation of Waterproof PVC Square Junction Box for CCTV Cameras IP65 5x5

IP-PBX

Supply , Installation , testing & Commissioning of EPABX SYSTEM : 32 Analog-Extension, Analog Trunk :04 , GSM Port 04 , PRI 30ch 1, SIP trunk -10 , IVRS , Voice mail and expendable up to 128 port .

Supply & Installation of 20 pair (MS/PVC) MDF Box with Krone module having locking facility

Supply, Installation , Testing & commissioning of Table mount Phones having display .

Supply & Laying of 2 Pair 0.50 mm sheathed telephone cable

P A System

SPEAKER : Supply of In-Ceiling Speakers - 150mm / 4" Full Range Driver, Compatible with 100v Line Volt, Amplifier Power Requirement 6 watts - 16/7 Use - BG/Public Address

AMPLIFIER : Supply, Installation, Testing & Commissioning of Digital 2 Channel mixer Amplifier - Min. 240 watts in Continuous Running Mode.

Supplying and installation of the zone controller cum digital signal processor builtin dante ,Min 16 AEC Inputs , Network Controlled .

Supply, Installation, Testing & Commissioning of networked Call station For PA system.

Supply & Laying of 2 core 1.5 SQ.MM. Heavy-duty audio copper cable ( 16 AWG) For PA system

Power Backup

UPS :Supply, Installation, Testing & Commissioning of 5 kva ONLINE UPS system with 15 minutes battery backup with single SMF battery bank retundancy mode compatible . 3 phase in & sigle phase out.

UPS :19 inch 2U , 1.5 KVA Rack Mountable UPS having 15 Min Backup . Builtin battery bank .

VRF SYSTEM WORKS

EQUIPMENT PART - AIR-CONDITIONING VARIABLE REFRIGERANT FLOW.

Supply of 415v - 3 Ph - 50 Hz Top Discharge type all inverter Variable Refrigerant Flow system , each Outdoor unit comprises of All Inverter Scroll Compressors, with Cooling/Heating mode, air cooled condenser with protective coated fins, Propeller type Fan with motor, electronic expansion valve, refrigerant cooled PCB, wide votage range will be preferred, Outdoor mounting frame, micro processor panel and other standard accessories as per specification. The unit shall be suitable for operation with R-410a refrigerant.

Supply of variable refrigerant flow 220-240v / 1ph / 50 Hz Ductable units comprising of coil, filter, fan. The unit shall be Mounted type and complete with all standard accessories.

3.2TR. High/Mid Static Ductable Units, 1130 cfm

4.5TR. High/Mid Static Ductable Units, 1412 cfm

Supply of variable refrigerant flow 220-240v / 1ph / 50 Hz Four Way cassettes units comprising of coil, filter, fan. The unit shall be Mounted type and complete with all standard accessories.Indoor units shall be compatible with BMS control system and fire detection port so that unit trips in case of fire.

1.28TR. Cassettes Units, 636 CFM

2.56TR. Cassettes Units, 812 CFM

AIR HANDLING UNITS

Supply Installtion, Testing and commissioning of factory built ceiling suspended/floor mounted double skin type Air Handling Unit with sectionalized, made of extruded Al section frame structure with thermal break profile of 25±2mm thick panels consisting of GI casing of thickness 0.6mm outside layer and 0.6mm plain GI sheet inside layer with polyurethane foam (PUF) insulation of density 40±2Kg/cum factory injected between them by injection moulding machine complete with DIDW forward/ backward curved blower section, 4/6 row deep chilled water cooling coil section with aluminium finned copper tubes ( tube thickness not less than 0.43mm & 12-13 Fins /Inch).

The AHU shall be completed with stainless steel drain pan with19 mm thck clsed cell class- O nitrile insulation,fire retardent canvas connection and necessary vibration isolation arrangement etc.

The motor shall be TEFC drive motor(IE3 and VFD compatible) suitable for 415±10% volts, 50 Hz, 3 phase, A.C. supply.

The complete AHU shall cinfirm to specification & face velocity across cooling coil shall be limited to 500 FPM maximum and fan oullet valocity not more than 1870 FPM.

Filter :Pre filter 90% efficiency to 10microne and fine filter 99% efficiency to 3 micron

The static pressure will be calcualted by HVAC contrctor on basis of final duct layout.

2500 CFM, 55 mm SP, 6.5 TR

AIR HANDLING UNITS FOR OT AREA

Type: Each operation room will be provided with 2 air handling unit sections. One unit will be supply air unit & another will be return / exhaust air unit. The supply air unit shall broadly comprise of inlet section with dampers, fresh air connection pre-filter section, supply air fan with motor, base frame, cooling / heating section as the case may be. Return air unit shall have inlet section with dampers, filter section, exhaust air fan with motor, base frame.

Supply of factory built floor mounted double skin type Air Handling Unit with Mixing Box, sectionalized, made of extruded Al section frame structure with thermal break profile of 46±2mm thick panels consisting of GI casing of thickness 0.6mm outside layer and 0.6mm aluminium sheet inside layer with polyurethane foam (PUF) insulation of density 40±2Kg/cum factory injected between them by injection moulding machine complete with DIDW backward curved blower section, 6 row deep DX cooling coil section with aluminium finned copper tubes ( tube thickness not less than 0.43mm & 12-13 Fins /Inch).

The AHU shall be completed with stainless steel drain pan with19 mm thck clsed cell class- O nitrile insulation,fire retardent canvas connection and necessary vibration isolation arrangement etc.

The motor shall be TEFC drive motor(IE3 and VFD compatible) suitable for 415±10% volts, 50 Hz, 3 phase, A.C. supply.

The complete AHU shall cinfirm to specification & face velocity across cooling coil shall be limited to 500 FPM maximum and fan oullet valocity not more than 1870 FPM.

AHU DX coils shall be in tune with the VRV Condensing Unit and equal divisions shall be made in cross sectional area of the coil respectively or as per manufacturer standard.

The unit shall be suitable for indoor installation and the static pressure will be calcualted by HVAC contrctor on basis of final duct layout.

Filter :Pre filter 90% efficiency to 10 microne and fine filter 99% efficiency to 3 micron

Heater :SS Strip Heater with 2 Bend PVC Elimininator.

3000 CFM, 150 mmwc SP, 8.0 TR, 3x2.5 Kw Heater For Supply Air unit & 2750 CFM, 40 mmwc SP For Exhaust Air Unit, Condensing unit capacity 11.0 TR

Supply of Corded controller

Supply of Cordless controller

Supply of Y joints / Distribution joints.

Supply of central controller for all IDUs on central point. Total system taken together.

EQUIPMENT PART - AIR-CONDITIONING VARIABLE REFRIGERANT FLOW.

Installation, testing and commissioning of the following All Inverter VRF outdoor units with first charge of R410A refrigerant, controls, electricals, necessary accessories of minimum capacity. Brick Pedestal / MS Structure for ODU as per design should be included in the offer.

50 HP VRF UNIT

19 TR DX Outdoor unit for OT

Installation of VRF Indoor Unit

Installation, testing and commissioning of Refrigeration Network (Y joints / Distribution joints/ Refnet joints) per sets as required.

Supply, installation, testing and commissioning of the various sizes Cu. refrigerant pipes as per specs duly insulated with 19mm/13mm close cell elastometric nitrite rubber insulation between each set of outdoor

Supply, installation, testing and commissioning of PVC pipe medium class (For drainage of water from IDU) with 6 mm thick Nitrile Rubber insulation.

Canvas conection.as per requirement.

Supply, fabrication, installation & testing of sheet metal ducting complete with Spliter Damper vanes as required and as per IS specifications and as per approved shop drawings.

0.63 MM (24 gauge) Galvanized Sheet Steel

0.8 MM (22 gauge) Galvanized Sheet Steel

1.0 MM (20 gauge) Galvanized Sheet Steel

1.2 MM (18 gauge) Galvanized Sheet Steel

Aluminium Duct

Supply, Febrication & Fixing of Aluminium sheet metal rectangular ducting as per IS 655/SMACNA complete with turning vanes, companion flanges, support, sealing of all seams with a suitable metal sealant as per drawings.

Aluminium Collar Damper

Supply Installation, testing and commissioning of Coller Damper of of aluminium constuction with black paint finish and complete in all respect as per drawings.

Motorised Duct Damper

Supply ,Fixing,testing and commssiooning of MOTORIZED duct dampers of 16G GI construction in supply air duct and reurn air duct as and where required with control wiring. The damper shall be motorised and spring return actuator to close the damper in the event of as require.

Motorised actuator with Controller for above damper.- 10NM

SS OT Planum

OT Planum constructed out of 1.6 mm thick Aluminium sheet of size 2400mm x 1800 mm x 400 mm height having 8nos. of size 595x595 and 2nos. of size 595x895 hepa filter as require. The hepa filters having dust spot efficiency of 99.99% 0.3 micron. Diffuser will be made out of perforated SS304 sheet.

DUCT INSULLATION

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class “O”) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.

DUCT ACOUSTIC LINING

Supply and fixing of duct accounstic lining inside the ducts with 10mm thick Class-1 open cell nitrile sheet (density 140-160kg/cum) pasted inside the duct using low VOC ashesive and harnessed with GI NUT Bolt.

DUCT DAMPERS

Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

Supplying, fixing, testing commissioning of supply air grill of powder coated aluminium with GI volume control dampers.complete as required.

Supplying, fixing, testing commissioning of Return air grill of powder coated aluminium with out GI volume control dampers.complete as required.

Supplying, fixing, testing commissioning of Continious air grill of powder coated aluminium .complete as required.

VOLUME CONTROL DAMPERS

Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

Supplying, fixing, testing commissioning of supply air diffuser of powder coated aluminium with GI volume control dampers.complete as required.

Supplying, fixing, testing commissioning of Return air diffuser of powder coated aluminium with out GI volume control dampers.complete as required.

Communication cabling between ODU and IDU as per OEM Specification.

2 core x1.5 Sqmm shilded cable.

Errection, testing and commissioning of central controller for all IDUs on central point

Fresh & Exhaust Air damper with Louver

Acoustic Insulation Of AHU Rooms

Supply and fixing of accounstic lining inside the AHU Room wall with 15mm thick Class-1 open cell nitrile sheet (density 140-160kg/cum) pasted inside the Room wall using low VOC ashesive and finally finish with 26 swg Aluminium Perforated sheet and required cosumables .

STRETCHER LIFT

Providing, fitting, fixing, installation,commissioning, testing and warranty etc all complete

LARIPA WORKS

STORM WATER DISPOSAL

Excavation work by mechanical means (Hydraulic Excavator)/ manual means in foundation trenches or drains not exceeding 1.5 m in width or 10 sqm on plan including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50m.

Providing box drain of 60 cm (ht) x 45 cm (width) of internal dimension with 1:2:4 Plum concrete (40mm & down) side wall thickness of 23 cm (hill side) and 30 cm (road side) with1:3:6 (20 mm & down) base concrete of thickness of 15 cm with standard specification over 15 cm stone soling including providing & laying guard stones, complete as per the direction of the Engineer-in-Charge.

Providing, fixing & removing form work for casting R.C.C items as indicated below: with locally available timber)

Providing and Laying 15mm thick cement plaster of specified mix in single coat including finishing even and smooth and curing etc all complete.

Cost of Haulage Excluding Loading and Unloading of stock material within 120 km all complete.

Loading and Unloading of Cement or Steel by Manual Means and Stacking.

Cost of Haulage Excluding Loading and Unloading of Sand within 50 km all complete.

Cost of Haulage Excluding Loading and Unloading of Stone chips within 50 km all complete.

Loading and Unloading of Stone Boulder/Stone aggregates/Sand/Kanker/Moorum.

Head load of non-stock materials for a distance beyond 30 m and within 100 m distance.

Haulage for throwing away of excavated earth via Surfaced Road for the distance of 30 km excluding loading and unloading all complete.

NON-SOR ITEMS

Providing, fitting & fixing of Galvanised Steel Grating of dimension 450 x 500 mm

RAIN WATER HARVESTING

Engagement of ordinary labour for Clearing and preparing the surface, labour for carriage and placement of water tank at designated platform including throwing of spoils etc all complete

Supply of water tank 5000L capacity (Rate as per STCS proforma invoice 22/STCS/PUR/H&FWD/700/25-26)

Transportation charges/delivery charges (Rate as per STCS)

Providing & fixing 15cm wide 45cm overall semicircular prepainted (HULLAS) sheet (Class I) gutter with iron brackets 40x3mm size, boltsfilled with epoxy in each bolts, nuts (8 to 10 gm per bolt), washers etc including making, connection with rain water pipes.

Soil pipe: 100mm dia PRINCE/SUPREME or equivalent soil pipe

Construction of platform (steel/cement concrete), connecting pipes, valves, labour charges etc. (payment to be made as per the actual measurement)

Provision for water pump etc all complete.

Provision for water filter etc all complete.

FURNITURE

LOW BEDS HOSPITAL SEMI FOWLER BED WITH ABS PANEL (2060 x 900 x 600) in mm

HOSPITAL FOWLER BED WITH ABS RAILING (2030 x 900 x 600)in mm

PLAIN EXAMINATION TABLE (2100 x 900 x 600)im mm

TYCHEMED STEEL ICU BED FOR PATIENT ELECTRICAL THREE FUNCTION BED (2060 x 900 x 600)in mm

MILD STEEL METAL SINGLE BED (1830 x 910 x 460)in mm

WOODEN COMPUTER LAB TABLE (900 x 450 x 760)in mm

Conference Table 4200L - 14 Feet (12 SEATER) (4200 x 1800 x 750)in mm

LOW BACK IC 123 MINI JAZZ LB INNOWIN OFFICE ERGONOMIC CHAIR (480 x 450 x 960)in mm

NILKAMAL TRENVI HIGH BACK OFFICE CHAIR (760 x 760 x 1220)in mm

DIRECTOR & EXECUTIVE L-SHAPE OFFICE TABLE LUXURY DESK MADE IN MDF WITH SIDE UNIT DRAWER AND STORAGE WIRE MANAGER - BROWN PLYBOARD WITH VENEER

COMFORT CVC-140-A 3 SEATER WAITING CHAIR (1220 × 460 × 610)in mm

STAINLESS STEEL SOFA CHAIR (510 x 470 x 1120)in mm

WOOD RECTANGULAR COFFEE TABLE (1100 × 550 × 430 )in mm

8 SEATER WOODEN CORNER L SHAPE SOFA (2135 × 915 x 460)in mm

MILD STEELRESTAURANT TABLE AND CHAIR (4 SEATER)

OFFICE FILING CABINET (1370 × 685 × 460)in mm

MATTE DESIGNER WOODEN BOOKSHELVES ENGINEER WOOD, FREE STANDING (760 x 410 x 1890)in mm

PHARMACY MEDICINE DRUG STORAGE CABINET MILD STEEL & PLASTIC BINS (960 x 470 x 2100)in mm

COMPOSITE FIBRE PANCHAKARMA MASSAGE BED (787.4 x 2895.6)in mm

THERAPY MASSAGE BED (787.4 x 2895.6)in mm

STRONG & DURABLE 6 SEATER DINING TABLE WITH CHAIRS

GENERAL SURGERY OT TABLE

INSTRUMENT TROLLEY

PATIENT STRETCHER TROLLEY

WHEEL CHAIR

LINEN CUPBOARD

Provision for Dismantling of existing structure

BURIAL PIT AND SHARP PIT

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Providing & Laying in position cement concrete of 1 : 2 : 4 (1 cement, 3 coarse sand, 6 graded stone aggregate of 20 mm and down size) including compacting curing etc. all complete.

Providing & Laying in position cement concrete of 1 : 2 : 4 (1 cement, 3 coarse sand, 6 graded stone aggregate of 20 mm and down size) including compacting curing etc. all complete.

Providing and Laying in position 1:1.5:3Mix (1cement, 1.5 coarse sand 3 graded stone aggregate 20mm and down nominal gauge) of reinforced cement concrete excluding the cost of form work, finishing and reinforcements.

Providing, fixing and removing form work for casting R.C.C items as indicated below:

Form Work for Foundation, footings, base of column etc. for mass concrete.

Form Work for Floor slab, roof slab, landing, balcony & access platform.

Column

Slabs

Supplying, bending and placing in position of Tor steel reinforcement in all R.C.C works i/c cost of binding wires all complete.

Providing and laying first class brick work in one brick thick in superstructure of standard size bricks with 1:5 cement mortar ( 1 cement and 5 coarse sand ) including carriage of bricks upto work site and curing etc. all complete.

Providing and laying 12mm thick cement plaster of 1:3 mix in single coat including finishing even & smooth and curing etc. all complete.

Supplying, fabricating, fitting and fixing steel tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shape washer etc as per the standard specification and design and direction of Engineer - in- Charge all complete.

Providing, fitting, fixing of 24 BWG GCI sheet roofing with lapping of 150mm (two corrugation) with G.I. hooks, bolts and nut 8mm dia with bitumen, GI limpet washers filled with white bad including coat of approved steel primer and two coats of approved paint, on overlapping of sheet excluding carriage all complete.

Cost of Haulage Excluding Loading and Unloading of stock material within 120 km all complete.

Loading and Unloading of Cement or Steel by Manual Means and Stacking.

Cost of Haulage Excluding Loading and Unloading of Sand within 50 km all complete.

Cost of Haulage Excluding Loading and Unloading of Stone chips within 50 km all complete.

Cost of Haulage Excluding Loading and Unloading of Stone within 50 km all complete.

Loading and Unloading of Stone Boulder/Stone aggregates/Sand/Kanker/Moorum.

WALL FOR SHARP PIT AND BURIAL PIT

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Providing & Laying in position cement concrete of 1:3:6 mix. (1 cement, 3 coarse sand, 6 graded stone aggregate of 20mm & down size)

Providing and Laying Plum concrete in 1:2:4 c.c. (1cement, 2coarse sand, 4clean hard graded stone chips of 20 mm down nominal gauge) with 50% clean hard stone of sizes not exceeding 15cm including shuttering, compacting and curing complete, as per the direction of Engineer in Charge.

Providing weep holes in Brick masonry/Plain/Reinforced concrete abutment, wing wall/return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical specifications

Cost of Haulage Excluding Loading and Unloading of stock material within 120 km all complete.

Loading and Unloading of Cement or Steel by Manual Means and Stacking.

Cost of Haulage Excluding Loading and Unloading of Sand within 50 km all complete.

Cost of Haulage Excluding Loading and Unloading of Stone chips within 50 km all complete.

Cost of Haulage Excluding Loading and Unloading of Stone within 50 km all complete.

Loading and Unloading of Stone Boulder/Stone aggregates/Sand/Kanker/Moorum.

Haulage for throwing away of excavated earth via Surfaced Road for the distance of 30 km excluding loading and unloading all complete. .

KARMA GOMPO BHUTIA (BID ID -3217)

SONAM TOPDEN BHUTIA (BID ID -3210)