SPECIAL REPAIR TO BLDG NOS HA 186 AND HA 202 AT BAGRAKOTE STN UNDER GE SEVOKE ROAD

Amount

Dismantling plain or corrugated steel sheeting any thickness, complete all as specified and directed.

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) removing rubbish off the premises etc complete all as specified and directed

Demolition of concrete (reinforced) of any description Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, removing rubbish off the premises etc complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exceeding 1.50 Sqm each, complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from frames) exceeding 1.5 sqmtr but not exceeding 4 sq m each, complete all as specified and directed.

Demolition of brickwork built in cement mortar and removing rubbish off the premises etc complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position, complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs of any thickness including cover fillets complete all as specified and directed.

Taking down cement plaster or lime plaster on walls /ceiling of any description from concrete or brick wall etc including raking out joints, hacking for key, scrubbing down with water and disposing off the retrieved debris as directed including necessary scaffoldings etc complete all as specified and directed

Excavating in trenches not exc 1.5m wide and n.exc 1.5 m in depth, for foundations, etc, or for shafts, wells, cesspits, manholes, pier holes, etc and not exceeding 10 square meter on plan for manholes etc and not exceeding 1.5m in depth and getting out in hard/dense soil complete all as specified and directed.

Returning filling in with approved excavated soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level nexc. 1.5 metre above the starting point complete all as specified and directed.

Materials and Labour for Sand filling under floors or in foundation including watering and consolidation complete all as specified and as directed.

Materials and Labour for plain cement concrete (1:2:4) type B-1, using 20mm graded stone aggregate as in holdfast block, filling of MS chowkats and the like including necessary formwork complete all as specified and as directed.

Materials and Labour for plain cement concrete (1:3:6) type C-2, using 40mm graded stone aggregate as in surface channel and drain complete all as specified and as directed.

Materials and Labour for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. all as specified and as directed.

Materials and labour for plain cement concrete (1:2:4) type B0(using 12.5mm graded stone aggregate) as in cills, steps, seismic and other similar bands, plinth courses, string courses , lacing courses, parapets and railings up to 60cm in height , copings, kneelers, apex stones, bed plates, kerbs including weathering , slightly rounded or chamfered angles and throating, complete all as specified and directed..

Materials and Labour for formwork to faces of sides and soffits of floor or roof beams, lintels, cantilevers, shelves including supports, overhangs, etc for rough finished flat surfaces of concrete complete all as specified and directed

Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

Materials and Labour for TMT bars 10 mm dia and over, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Materials and Labour for TMT bars 6 to 10 mm dia in stirrups, spacers and binders, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Materials and Labour for 6 to 8 mm dia round bars as in reinforcement for half brick thick walls, cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Materials and Labour for rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.conforming to Fe 410-W (Gde-E- 250) quality-A/Fe.290.Gde-E-165 including painted one shop coat of zinc chromate primer paint (including preparation of surface) at workshop before fabrication complete all as specified and as directed.

Supply & fixing Mild steel screw bolt (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends each screwed end to be filled with washers and one hexagonal or square nut 5 to 10mm dia shank and exc 5cm but n exc 10cm long complete all as specified and as directed.

Supply & fixing mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

Supply & fixing rolled mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment (Fe 290 Gde-E 165) complete all as specified and as directed.

Supply & fixing Mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to steel trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165.

Supply & fixing mild steel as in wind ties for roof including securing bolts and similar work steel conforming to Fe 290 Gde-E-165 complete all as specified and directed.

Supply and fixing Pre-painted galvalume aluminum zinc coating (AZ-150) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Supply and fixing Pre-painted galvalume aluminum zinc coating (AZ-150) GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws , complete all as specified and directed.

Materials and labour for preparing of new wooden surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Materials and labour for preparing of new steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Materials and labour for preparing of new steel surfaces of any description , below 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement mortar (1:6) for laying of floor finishes complete all as specified and directed.

Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,on vertical surfaces such as skirting,dado and risers to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 10mm thick screed bed or bedding layer of cement mortar (1:4) complete all as specified and directed.

Materials and labour for Kota stone slab 20-25mm thick in riser of steps,skirting,dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10mm thick backing coat in cement mortar (1:4) including rubbing and polishing complete.

Materials and labour for Kota stone slab 20-25mm thick in floor laid over and including 20mm thick screed bed or bedding layer of cement mortar (1:6)and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Materials and labour for 60mm thick Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658- 2006 M-35 grade, laid as directed to any shape. Complete all as specified and as directed

Materials and labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate as in floors, plinth protection, path etc. finished the surface of concrete even and smooth smooth without using extra cement, complete all as specified and directed.

Materials and labour for 25 mm thick PCC (1:2:4) type B1 using 20 mm graded stone aggt as in sub bases of floor finished even and rough, complete all as specified and directed.

Materials and labour for 75 mm thick plain cement concrete (1:4:8) type D2 using 40 mm graded stone aggregate as in sub-base of floors etc. finished the surface of concrete fair and even, complete all as specified and directed.

Materials and labour for brick work with sub class 'B' burnt clay bricks straight or curved on plan exc 6 meter mean radius built in cement mortar 1:6 complete all as specified and as directed.

Materials and labour for brick work with sub class 'B' burnt clay bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

Supply and fixing 105 x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hings lock strike plate etc complete all as specified.

Supply and fixing flush door shutters 30mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Supply and fixing 150mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed.

Supply and fixing Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing complete all as specified and as directed.

Supply and fixing anodised powder coated aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

Materials and labour for providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws. complete all as specified and directed

Supply and fixing anodised powder coated aluminium (minimum thickness of powder coating 50 micron) door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised alumnium snap beading, screws handles 2 nos in each door,hinges etc. complete all as specified and directed

Supply and fixing Anodised aluminum grill (anodised tansparent or dyed to required shade according to IS : 1868 with minimum anodic coating of grade AC 15) of approved design/pattern., with approved standard section and fixed to the existing window frame with C.P brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and derection of Engineer-in-charge.

Supply and fixing Aluminium anodized barrel tower bolts of extruded section, 150 mm long, complete all as specified and directed.

Supply and fixing extruded aluminium alloy handles, fabricated type, anodized, 150 mm size , complete all as specified and directed.

Supply and fixing for 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Supply and fixing mild steel stove enamelled black 300mm long ordinary rat tail rod pattern spring fixed with screws to wooden chowkhats or welding to steel chowkhats, complete all as specified and directed.

Supply and fixing Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, including one coat of red oxide primer complete with glazing bars, dovetailed or welded complete all as specified and directed.

Supply and fixing steel ventilators with top hung shutter including hinges,steel peg stay, including one shop coat of Zinc Chrome primer complete all as specified and directed.

Supply and fixing 3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares n.exceeding 0.50sqm in each pane , complete all as specified and directed.

Supply and fixing 4.80 mm thick plain glass to be fitted with aluminium framework complete all as specified and directed.

Supply and fixing 6.30 mm thick plain glass to be fitted with aluminium framework complete all as specified and directed.

Supply and fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Materials and labour for rendering 15mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

Materials and labour for rendering 20mm thick in two layers of 10 mm thick each in cement mortar (1:4) on fair faces of brick work or concrete surfaces,WPC shall be mixed with morter of top layer, finished even and fair, complete all as specified and directed. (Note: WPC shall be measured and paid separately as supply only)

Supply only liquid Water Proofing Compound of approved make.

Materials and labour for applying three coats of white wash on new wall surface including preparation of surface, complete all as specified and directed.

Materials and labour for preparation of new plastered surfaces and applying two coats of cement based paint over a coat of alkali resistant primer on wall complete all specified and directed.

Materials and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper of approved colour with roller over chalk whitening after preparation of surface complete all as specified and directed.

Materials and labour for 605X605mm anodised aluminium snap grid frame work for false ceiling including hangers 2.5 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including supply and fixing 4mm thick Decorative non asbestos fibre cement boards fixed or laid/ inserted to aluminium frame work as in ceiling complete all as specified and directed. Note:- The size of aluminium main and cross tee shall be 40mm x25mm x2mm and size of angle shall be 25mm x 25mm x 2mm or higher)

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc

Materials and labour for concealed point wiring with two runs of FRLS PVC insulated unsheathed, 1100 V grade cable multi stranded copper conductor of size 1.5 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 1.50 sqmm green in colour as earth lead, drawing through in and including PVC rigid conduit of size not less than 20mm, with all fittings & accessories including provn of MS sunk terminal box of appropriate size suitable for switch fixed flush to wall for mounting switch, sockets, fan regulators etc with 3mm thick hylum sheet top cover with screws & cup washers for one light / fan point / call bell complete. NOTE : Cost of making good the disturbed surfaces (if any) matching with the existing surface is deemed to be included in the unit quoted rates. all as specified and directed.One light/fan/call bell point controlled by one switch one way 5 Amps

All as per Item No.71 above but for One 2/3 pin socket outlet 5/6Amps on independent board

All as per Item No.71 above but for one switch socket combination 15/16 Amps on independent board with cable 2.5 sq mm size and earth wire 2.5 sqmm

Supply and fixing Switch piano, flush type, single pole, one way switch 5 Amps.

Supply and fixing Switch socket combination 2 in 1, 5 Amps flush type.

Supply and fixing Switch socket combination multipurpose 5 A/16 Amps,5 in 1, flush type.

Supply and fixing Ceiling rose surface bakelite 3 terminals 65x50mm all as directed.

Supply and fixing electronic step regulator (speed regulation in 5 steps) suitable for ceiling fan 1200 sweep/1400 mm, 120 Watt complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

Supply and fixing Lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Supply and fixing LED Lamp, 9 Watt B22 complete all as specified and directed.

Supply and fixing in repair energy saving and environmental friendly long life LED security/street Light fittings 35 watts, made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover, IP 66 protection, inbuilt driver, connecting with suitable size copper wire, with 32mm bore 1 m long medium grade GI bracket made to shape complete all as specified and as directed.

Supply, fixing and connecting exhaust fan made of polycarbonate/sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and as directed.

Supply and fixing in repair decorative box type surface and wall mounted 18/20 Watt LED light fittings, 6500 K, 4 feet long, with aluminium housing and integrated electronic driver, fixed to walls/ceiling, environmental friendly, energy efficient ready to use pack .

Supply and fixing MCB distrubution board SPN 4way, double door, IP 42, IK-09, sheet steel, phosphatised,powder coated with 200 amps rated bus-bar,neutral link,earth bar and din rail, 240 V, including taking down existing unserviceable DB with MCBs complete all as specified and directed. by Engineer-in-charge.

Supply and fixing MCB distrubution board SPN 8way, double door, IP 42, IK-09, sheet steel, phosphatised,powder coated with 200 amps rated bus-bar,neutral link,earth bar and din rail, 240 V, including taking down existing unserviceable DB with MCBs complete all as specified and directed. by Engineer-in-charge.

Supply and fixing MCB Single pole, 240 volts 5 to 32 Amps 10 KA rupturing capacity, C series

Supply and fixing MCB Single pole & neutral, 240 volts 32 Amps 10 KA rupturing capacity, C series

Materials &Labour for submain concealed wiring with two single core PVC insulated, unsheathed, stranded copper conductor of size 6.0 Sqmm and one single core PVC insulated, unsheathed stranded copper conductor 6.0 Sqmm green in colour as earth continuity conductor drawn into and including PVC conduit (medium grade) with all fitting & accessories incl taking down old unsv aluminium sub-main wiring complete all as specified and directed by Eng-in-Charge .

Supply and laying or fixing or passing through pipe and connecting UG, XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 sq. mm 2 core in replacement of existing cable complete all as specified.

Materials and labour for GI pipe light grade with all fittings complete grouted in ground all as specified for 40 mm bore of pipe laid in trenches/fixed with poles/laid in road/plinth/floor for protection of cable complete all as specified and directed.

Supply & laying 50 mm outside dia double wall corrugated pipe(DWCPE) for enclosing cable below ground/road surface to a required depth including suitable size couplers for jointing of pipe all as per site requirement etc complete all as specified and directed.

Materials and labour for boring holes 1mtr deep in soil under roads/PCC as directed for cable passing through pipes of required size and disposal of soil to a distance not exc. 50m. (Note: Connected items like Pipes is measured and paid seperately under relevant items).

Materials and labour for earthing complete with galvanized steel pipe electrode 40mm bore , medium grade, 2.5 meters length, buried directly and preferably vertically in ground with top edge not less than 1.25 meters below ground level connected with earthing lead galvanized iron strip of size 25x5 mm connected to galvanized earth pipe by means of bolts, nuts, checknuts and washer of galvanized iron including PCC (1:2:4) type B1 precast RCC cover slab with suitable handle made of 6mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanized steel tube for watering with one end fix with cast iron funnel and wire-mesh , with protection pipe of 32 mm dia light grade galvanized steel tubing upto 7.5 meters length for drawing earthlead including common salt, charcol , bentonite in alternate layers etc, complete all as shown in EP number 2 of SSR part-1 including testing on completion and including taking down old u/s earthing & testing complete all as specified and as directed.

M/S JANARDAN SHARMA AND SONS

NARESH GUPTA