ADDITIONAL / ALTERATION TO WET CANTEEN

Amount

Demolition of brick/stone masonry built in cement mortar including all quins arches, pillars etc complete all as directed.

Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15 cm thickness below or above ground level, removal fo rubbish and debris and depositing in low lying areas complete all as directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as directed.

Taking down chowkhats or frames not exc 1.50 sqm (without takng shutters from the frame) complete all as directed.

Taking down chowkhats or frames exc 1.5 sqm but not exc 4.00 sqm (without takng off shutters from the frame) complete all as directed.

Dismantling of framed timber scantlings 40 sq. cm and over in section, in any position complete all as directed.

Dismantling boarding, any description, fixed any position with nails,complete all as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads,complete all as directed.

Taking down cement plaster on brick/stone masonry walls, ceilings etc. including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing removing serviceable tiles to store and rubbish off the premises complete all as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc.,complete all as directed.

M& L mild steel Roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc,complete all as directed.

Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0,complete all as directed.

S&F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick or any colour having tensile strenght of 5510 Mpa as in roof cvrings/cladding to wall, fixed with self tapping screws,complete all as specified and as directed.

M&L Preparation of old apinted surfaces of steel or iron surfaces of any description not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint all as specified and directed.

M & L for Fly Ash Brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 m mean radius, built in CM 1:6 complete all as specified and directed.

M & L for rendering 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces, rendering is to be finished even and smooth without using extra cement,complete all as specified and directed.

M & L Rendering 15mm thick on brick or concrete surfaes in CM 1:4 using integral waterproofing compound finished even and smooth without using extra cement complete all as specified and directed. Note:- Intergal waterproofing compound shall be measured and paid separately.

Supply only integral waterproofing compound.

S&F 2nd class hard wood plain, solid, straight chowkats and frams wrought, framed rebated on solid, rounded or chamfered put together with glue pinned at joints,complete all as specified and directed.

S&F 2nd Class HW rail and style 35mm Thickness Factory made shutters Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated,complete all as specified and directed.

S& F 30mm thick Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, fixing in opening,complete all as specified and directed.

S & F 30mm thick Flush shutters, solid core construction, with particle board core and both faces is covered with decorative face veneer with lipping/frame to match,complete all as specified and directed.

S&F Factory made solid panel pace door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame,complete all as specified and directed.

S&F mild steel butt hinges, medium weight cold rolled 100mm size,complete all as specified and directed.

S&F 200 mm aluminium anodized, barrel tower bolts of extruded section,complete all as specified and directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized,complete all as specified and directed.

S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy,complete all as specified and directed.

S&F floor door stopper 150 mm of aluminium alloy body and tongue anodized with hard drawn steel spring fixed,complete all as specified and directed.

Door closer hydraulically regulated, designation No 3, universal type,Aluminium (extruded section body) suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed,complete all as specified and directed.

S&F mild steel work as Bands, straps, hold fasts and similar small articles conforming to Fe410-0 or Fe 310-0,complete all as specified and directed.

S & F False ceiling of 12.5/ 12 mm thick tapered edge gypsum board tiles of size 600mm x 600mm or 605mm x 605mm confirming to IS : 2095 with two coats of plastic emulsion paint of approved colour including providing and fixing of snap grid frame work made of special section, power pressed from MS as per manufacturer's instructions. Sheet and galvanized in accordance with Zinc coating 600 as per IS : 277 and consisting of angle cleats of size 25 mm wide x 16 mm thick with flanges of 22 mm and 37 mm at 1200 mm c/c. One flange is fixed to the ceiling with a dash fasteners 12.5 mm x 40 mm long with 6 mm dia bolts to the angle hanger fixed with nut and bolts to the GI channels 45 mm x 15 mm x 0.9 mm, running at 1200 mm c/c, to which the ceiling section 0.5 mm thick, bottom, wedge of 80 mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450 mm c/c shall be fixed, in a direction perpendicular to the GI channels, with connecting clips made out of 2.64 mm dia x 230 mm long GI wire at every junction including fixing the 27 mm high section having flanges of length 20 & 30 mm. The perimeter of fixing false ceiling to the wall/partition with the help of rawl plugs at 450 mm c/c with long drive screws. False ceiling shall be fixed as per manufacturer's instructions and all as directed. Make/ Manufacturers ; saint Gobain / Lafarge / Knauf/ Arm strong.

M&L 30mm thick Cement concrete (1:2:4), type B-0, using 20mm graded stone aggregate as in floor including finished floor surface even and smooth with using extra cement,complete all as specified and directed.

M & L for 75mm thick plain cement concrete(1:24), type B-1, using 20mm graded stone aggregate as in floor, Plinth Protection, foot path etc complete including necessary form work and finishing exposed surface fair and even,complete all as specified and directed.

S&F Vitrified ceramic tiles 10mm thick (square/rectangular) area light shade of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm,as in floors etc. set and jointed in neat cement slurry, laid over 15mm thick screed bed in CM 1:4 and pointed in white cement or coloured cement to match with colour of tiles,complete all as specified and directed.

All as per item No.36 above but as in skirting /Dado, set and jointed in neat cement slurry and pointed in coloured cement to match with tiles laid on and including 10 mm thick rendering in CM 1:4 as backing layer,complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc over 15mm thick screed bed in CM 1:6, jointed and pointed in white or coloured cement to match with the colour of tiles,complete all as specified and directed.

M&L for glazed multi coloured glazed ceramic tiles incl border of size 350x250x7mm/450x 350 x 7mm thick as in vertical surfaces such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles laid on and including 10 mm thick rendering in CM 1:4 on fair faces of brick/ concrete surfaces,complete all as specified and directed.

M/L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete set and jointed in neat cement slurry, laid over 15mm thick screed bed in CM 1:4 and pointed in white cement or coloured cement to match with colour of tiles,complete all as specified and directed.

Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types laid over 15mm thick screed bed in CM 1:4 and pointed in white cement or coloured cement to match with colour of tiles,complete all as specified and directed.

20mm thick Granite (of any type) tiles machine cut in skirting/dado laid over cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing of type laid over 15mm thick screed bed in CM 1:4 and pointed in white cement or coloured cement to match with colour of tiles,complete all as specified and directed.

M&L for two coats of distemper oil emulsion over a coat of alkali resistent paint over two coats of putty including removal of existing treatment of wall treatment of wall surfaces,complete all as specified and directed.

S&F 12mm thick decorative tinted glass fixed as in partetion of wall/ verticaly set and jointed insuitable top and bottom rails ,beddings and fittings screws etc surfaces complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceiling and applying two coats of two coats of white wash,complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood or wooden based sufaces of any description, not otherwise described, over 10 cm width or girth and applying Two coat of synthetic enamel paint over a coat of pink primer,complete all as specified and directed.

S & F in repairs vitreous china wash hand basin, white, flat back of size 550x400 mm excluding taps, waste, chain and plug and procelain stopper but including bracket and waste fittings, brass, CP 32 mm dia,complete all as specified and directed.

S & F in repairs vitreous china wash down water closet pan (pedestal pattern) (EWC), white including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device and fixing bolts,complete all as specified and directed.

S & F in repairs vitreous china urinal, Half stall type, white, with urinal spreader of chromium type fixing with 15mm dia pipe, bracket, including necessary connection to flush pipe and waste pipe,complete all as specified and directed.

S & F in repairs 10 litres capacity, PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and suitable flush pipe PVC 32mm dia,complete all as specified and directed.

S&F towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/ plastic cleats (Minimum weight 190gms),complete all as specified and directed.

S & F repairs 15 mm dia Bib taps, cast copper alloy chromium plated Fancey type with capston head handle, screwed down, screwed for iron pipe, complete all as specified and directed.

S & F 15 mm dia stop valves, Fancy type chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe,complete all as specified and directed.

S & F 15 mm dia Fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long screwed shank and fly nuts, screwed for iron pipe,complete all as specified and directed.

S & F PVC connections 15mm size with PTMT nuts of length 450mm long,complete all as specified and directed.

S&F 32mm dia High density polyethylene pipes (HPDE) of pressure rating 6Kgf/cm2 fixed complete to walls, ceiling or in floors etc.,complete all as specified and directed.

S&F steel tubing and connections and supply and fixing 15mm dia GI steel tubes, medium grade with all fitting and fixed complete to walls and ceiling or laid in floors,complete all as specified and directed.

S&F steel tubing and connections and supply and fixing 20mm dia GI steel tubes, medium grade with all fitting and fixed complete to walls and ceiling or laid in floors,complete all as specified and directed.

S&F steel tubing and connections and supply and fixing 25mm dia GI steel tubes, medium grade with all fitting and fixed complete to walls and ceiling or laid in floors,complete all as specified and directed.

S&F25mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed,complete all as specified and directed.

M&L for stainless steel grade 304 railing 68mm dia hand rail and 3 Nos 16mm dia horizontal rails and 40mm dia verticals at 900mm centre to centre including Cup,plate or other ornamental items as required,complete all as specified and directed.

M&L for stainless steel grade 304 ,Stainless steel cover sheet fixed on drain surface including screws,hold fasts and any other packing materials etc to proper contact with drain suface,complete all as specified and directed.

S & F Temperd decorative glass 8mm thick 50cm width Fixed at stainless steel railling with suitable stainless steel scews, nuts etc,complete all as specified and directed.

M&L RCC (1:2:4),Type B1, using 20 mm graded stone aggregate as cover slabs (for manholes etc.) and set in Cement mortar 1:4,complete all as specified and directed.

S& F TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

S&F UPVC multicavity three tire frame section 75mm x 65mm x 205mm suitable reinforced with GI and shutter made out of 5mm thick tinted sheet glass and EPDM gasket provision for glass in window alongiwth sliding mosquito proofing shutter,complete all as specified and directed.

S&F UPVC fixed ventilator of white colour classic premium series with provision of 5mm thick toughened glass,complete all as specified and directed.

S&F for rectangular aluminium hollow section of size 101.6 x 44 x 2mm thick as in partition (including fixing with nut and bolt in floor and wall by drilling holes), poweder coated of approved colour for both vertical and horizontal member including 5.5mm thick glass, 12mm thick particle board prelaminated on both side, aluminium legs, aluminium glazing channel, rubber beading as required,complete all as specified and directed.

All as per item No 69 above but as in door, poweder coated, approved colour, including 5.5mm thick glass, 12mm thick particle board prelaminated on both side, rubber beading, aluminium glazing channel, two Nos handles, three Nos extruded aluminum hinges 100 mm long, two Nos 200 mm aluminium anodized, barrel tower bolts of extruded section, one floor door stopper 150 mm of aluminium alloy body, 100mm size brass mortice lock, 4 levers with two keys and floor door spring as required for door,complete all as specified and directed.

Taking down old unserviceable point wiring (Light,Fan,bell,Socket or power) complete including fixture and fittings such as switches, ceiling roses,regulators, sockets, light fittings etc and making good to the disturbed surfaces of walls,ceilings and floor match the existing shade complete all as specified and directed.

Material and labour for point wiring complete with ISI marked 1.5 Sqmm PVC insulated unsheathed multistranded single core cable with copper conductor (FRLS) 1100 volts grade drawn through and including PVC rigid conduit not less than 20 mm or higher dia ISI marked as required at site including conduit accessories such as Junction Boxes, Inspection Covers etc, concealed/surface type on any type walls, roofs, floors etc by means of saddles and clamps etc including PVC junction boxes ISI marked suitable for modular switches & sockets of necessary modules as per site requirement including modular plates & covers for switches sockets, regulators etc. including providing of 1.5 Sqmm PVC insulated FRLS multistranded unsheathed copper conductor as earth continuity conductor and connecting to common earth dolly complete all as specified and directed for One light/ fan point/exhaust point controlled by one, one way switch/bell push Note- Rates include the cost of modular plate and covers of suitable modules as required at site.

All as per item No. 72 above but for 5 Amps socket on independent board

All as per item No. 72 above but for 5 Amps socket on same board

All as per item No. 72 above but wiring with 2.5 Sqmm for 15 Amps switch socket combination on independent board/two pin earth plug and socket including providing 2.5 Sqmm PVC insulated unsheathed copper conductor cable as earth continuity conductor and connected to common earth dolly,complete all as specified and directed

Supply and Fixing Modular switch single pole, one way 6 Amps one module,complete all as specified and directed

Supply and Fixing Modular switch single pole, one way 16 Amps one module,complete all as specified and directed

Supply and Fixing Modular socket 6 Amps multipurpose 2 in 1- 2/3 pin combined 2 module,complete all as specified and directed

Supply and Fixing Modular socket 6/16 Amps multipurpose 2 in 1 -2/3 combined 2 module,complete all as specified and directed

Supply and Fixing ceiling rose three terminals Poly carbonate isolated body,complete all as specified and directed

Supply and Fixing Modular step type fan regulator 230 Volts, 120 watt 2 module,complete all as specified and directed

Supply & Fix in replacement recess mounted LED luminaire 36W 2'x2', 6500K, fully diffused, CCT, luminous efficacy of not less than 120lm/watt designed for metric false ceiling type or alongwith frame suitable for Armstrong/ US Gypsum or similar mounting system with concealed or exposed 'T' sections, Glare free light alongwith electronic driver complete with all accessories prewired and connecting up with three core twister flexible copper conductor cable with suitable size complete removing unserviceable fittings all specified and directed. Make:Havells Cat Part No. PLANO2X2PLR36WLED857S or equivalent in PHILIPS /Wipro

S&F 1x22W,230V surface and wall mounted LED batten,with extended aluminium housing along with industrial heavy duty driver having THD <10% lumen out put not less than 100 lm/w including connecting up with twin core twisted flexible copper condctor cable from ceiling rose all as specified. Make:- Havells Cat Part: LUMILINEPLUSBS22WLED865SPCSS or equivalent in PHILIPS /Wipro

Supply and Fix Bldg Security LED luminaire 20 W 5700K complete with all accessories prewired and including connection up with three core twister flexible copper conductor cable with suitable size complete removing unserviceable fitiings all as specified and directed. Make:Havells Cat Part: ENDURAPEARLSL20WLED757SASYTOPCMP or equivalent in Wipro/Philip

Supply and Fix single pole and neutral metal clad enclosure WITH MCB SP 20 Amps with a 2 pin metal clad earth plug & socket complete all as specified and directed.

Supply and fixing factory made epoxy powder coated Distribution Board TP & N 4 way double door ( MCB DB ) MCB TPN as In comer & MCB's as out going with metal door (IP-43 protection, IK-09) as per IEC-61439 fabricated from CRCA sheet and fixed semi flush to wall and suitable for universal mounting and neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockout semi flush to wall and making good disturbed surface and touch up with the same finishes,complete all as specified and directed

Supply and fixing factory made epoxy powder coated Distribution Board TP & N 8 way double door ( MCB DB ) MCB TPN as In comer & MCB's as out going with metal door (IP-43 protection, IK-09) as per IEC-61439 fabricated from CRCA sheet and fixed semi flush to wall and suitable for universal mounting and neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockout semi flush to wall and making good disturbed surface and touch up with the same finishes,complete all as specified and directed

S&F MCCB with rating of 100 Amps,415Volts 4pole with 25kA breaking capacity,thermal magnetic adjustable of overload & short circuit release confirming IS-13947 & IEC 60947-2 & the service short circuit breaking capacity (Ics) should be equal to ultimate breaking capcity(Icu).MCCB should be with suitable spreaders and phase barriers for each terminals,complete all as specified and directed.

S&F MCB TPN 63 Amps 240V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing,complete all as specified and directed

Supply and fix C Curve MCB SP 6-32 Amps working on 240 volts,50 Hz 10 KA,complete all as specified and directed

Supply & Fix factory made Sheet metal enclosure suitable for MCCB TPN, 100A, capacity including fixing on surface/semi flush to wall with nut bolts, making connection with existing cables complete with lugs, glands complete all as specified and directed.

M & L for sub main wiring with 2 runs of 6 Sqmm single core PVC FRLS insulated unsheathed cable 1100 Volts grade multistranded with copper conductor drawing through rigid PVC conduit medium grade of 25 mm dia including conduit and conduit accessories such as bends,tees,junction boxes concealed/surface type on walls, roof, floors etc including 1 run of 6 Sqmm PVC insulated FRLS copper conductor cable as earth continuity wire including taking down unserviceable sub main wiring and conduit all as specified and directed. Note: 2 Runs of 6 sqmm cable and 1 run of 6 sqmm cable and 1 run of PVC conduit shall measured as one unit

M & L for sub main wiring with 4 runs of 6 Sqmm single core PVC FRLS insulated unsheathed cable 1100 Volts grade multistranded with copper conductor drawing through rigid PVC conduit medium grade of 25 mm dia including conduit and conduit accessories such as bends,tees,junction boxes concealed/surface type on walls, roof, floors etc including 2 run of 6 Sqmm PVC insulated FRLS copper conductor cable as earth continuity wire including taking down unserviceable sub main wiring and conduit all as specified and directed. Note: 4 Runs of 6 sqmm cable and 2 run of 6 sqmm cable and 1 run of PVC conduit shall measured as one unit

M & L for sub main wiring with 4 runs of 10 Sqmm single core PVC FRLS insulated unsheathed cable 1100 Volts grade multistranded with copper conductor drawing through rigid PVC conduit medium grade of 32 mm dia including conduit and conduit accessories such as bends,tees,junction boxes concealed/surface type on walls, roof, floors etc including 2 run of 10 Sqmm PVC insulated FRLS copper conductor cable as earth continuity wire including taking down unserviceable sub main wiring and conduit all as specified and directed. Note: 4 Runs of 10 sqmm cable and 2 run of 10 sqmm cable and 1 run of PVC conduit shall measured as one unit

Taking down ceiling/exhaust/wall mounted/pedestal fans/ air circulators of any sweep of any make with down rods, blades canopy etc by disconnecting the electric connections, removing worn out bearings, capacitor, bushes and over hauling including replacement of minor parts like split pins, nuts, screws, washers etc and other worn out spare parts as required, greasing, reassembling and reconnecting with 3 core new flexible cord from ceiling rose to fan, testing and commission complete all as specified and directed.

Disconnecting and taking down indoor and outdoor unit of split AC of any make and capacity upto 1.5/2 Ton with stabiliser from the existing position, servicing, gas top up minor repair and refixing the same after renovation of the building

Disconnecting and taking down fire alarm system complete with smoke detectors cables, panels, hooters etc from the existing the position and refixing the same in its position after renovation of building and testing complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 m deep below normal ground level with top edge of earth plate, not less than 1.5 m below normal ground level connected to galvanised iron earth lead of size 4.0 mm dia by means of bolts, nuts/check nuts and washers etc of galvanised iron, protected by galvanised iron pipe light grade 15 mm dia upto a length of 7.5 m away from earth electrode and connected to main switch/control board including necessary excavation earth work in any type of soil and PCC 1:3:6 type C1 for earth chamber, 40 mm thick RCC cover slab 1:2:4 type B1 with 6 mm dia TMT Bars at 140 mm cc both ways, watering pipe 20 mm dia light grade GI, funnel, wire mesh, lugs, charcoal and salt etc complete all as shown in Electrical plate No. 3 SSR Part I and testing complete including removing unserviceable items all as specified and directed.

GI earth wire of 4 mm dia fixed on walls/floor as earth continuity conductor connected to DBs/ panels etc.,complete all as specified and directed

Supply and fixing PVC conduit medium grade of size 25mm dia bore complete all as specified and directed.

Supply, Laying, Test & Commissioning LT UG cable of size 50 sqmm; 3.5 core XLPE insulated, armoured, multistranded heavy duty, aluminium conductor electric cable of 1100 volts grade laid in ground/fixing on wall with necessary clamps, connecting with aluminium lugs, necessary cable glands etc and including removing old unserviceable cable all as specified and directed.

All as per item No. 102 above but of size 35 sqmm 3.5 core complete all as specified and directed.

Excavation in trenches not exc.1.5 Mtr in width and not exceeding 1.5 Mtr in depth for laying of cables and getting out in hard/dense soil etc complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layer not exceeding 25 cm thick using soil complete all as specified and directed.

Removing excavated surplus soil to a distance not exceeding 50 Mtr and depositing where directed at a level not exceeding 1.5 Mtr above the starting point all as specified.

Supply and filling Dry river sand for cushioning to cables in trenches including spreading, levelling complete all as specified and directed. Note:- Punned thickness will be only be considered for payment purpose.

Supplying and laying un-reinforced precast concrete cable cover, class LV, type 1 with peak, size 250mm x 150mm x 40mm complete all as specified and directed.

S&F light grade GI pipe protection of earth strip of size 40mm dia all as specified. Make :Tata/Jindal/Zenith / Surya.

M/s K Venkateswara Rao

M/S GDR CONSTRUCTIONS