PROVN OF TILING IN BLDGS P 2A CHAIN LINK CATTLE FENCING NEAR PT GROUND INTER LOCKING PATHWAY IN FRONT OF CERTAIN BLDGS DRAINAGE SYSTEM BEHIND JCOS MESS 07 SOAKAGE PIT FOR URINAL POINT BOUNDARY WALL AROUND QTR NO P 99/6 INTER LOCKING PAVER BLOCK HAR

Amount

Excavation in post holes (or similar holes) each not exceeding 0.5 cum, getting out, returning, filling in and ramming earth in layers n exc 25cm ,watering in soft/loose soil all as specified

Excavation in trenches , n. exc1.5 m wide and n exc. 1.5m in depth ; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan n exc. 1.5 m in depth and getting out in soft/loose soil complete.

Excavating in trenches not exceeding 1.5 metre wide and exc 1.50 m in depth & not exceeding 3.0 metre for pipe line or for manholes not exc. 10 sqm on plan in any type of soil and getting out.

Returning, filling in (soil) including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil etc complete all as spd.

Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point.

M&L Cement concrete 1:3:6 type C 1 (using 20 mm stone aggregate ) as in coloumns posts pillars and boundary pillars comlete all as specified and as directed By Engineer In Charge.

M&L for Cement concrete 1:4:8 Type D-2 in foundations, filling and mass-concrete comlete all as specified and as directed By Engineer In Charge.

M&L for Brick work with Fly Ash old sized bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 complete all as specified and as directed by Engineer-InCharge.

M&L for brick work with Fly Ash bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:4 in half brick thick wall.

M&L for Brick work with old size sub class 'B' bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6 m mean radius with old size bricks built in cement mortar 1:4.

M&L for PCC 1:2:4 Type B-0 using 12.5 mm graded aggregate as in coping above wall under fencing complete all as specified and as directed by Engineer-In-Charge.

M&L for Reinforcement cement concrete Nominal mix M-25 as in Plinth Band/Lintal band and the like incl necessary form work the like using 20mm graded stone agg complete all as specified.

S&F MS Angle iron as in posts struts for fencing posts,gates etc confirming to Fe290 Gde E-165-0 complete all as specified.including provision for fixing chainlink fencing and barbed wire .

Supply only Chain link MS gavinised fencing any size and type as specified and directed

Fixing only Chain link fencing for serial item no.above complete all as specified and as directed by engineer-in charge.

S&F MS flat iron to secure chain link fencing all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and ncluding mild steel wire (annealed) not less than 0.9mm dia or security with clips, all as specified.

M&L for Mild steel TMT bars 6mm to 8mm dia in reinforcement cut to length, bent to shape required incl bending spirally cranking, hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or security with clips, all as specified.

M&L mild steel round bars 10 mm dia or over, cut to length, bend to shape required, fixed independently to support chain link fencing complete all as specified. Fe 410-0 or Fe 290 Gde E-165

Mild steel screw bolts(machine made) square head at one end screws on other for washer and nut n exc. 5cm long with dia of neck exc 12mm

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as spd and directed.

M&L for Rendering 10mm thick on brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement all as specified.

M&L for Rendering 5mm thick on brick or concrete surface as in ceiling in cement mortar 1:3 finished even and smooth without using extra cement all as specified.

M&L for 15mm thick rendering in two layer on fair faces of brick masonry or concrete surfaces of walls in CM 1:4, finished fair & even, complete, all as specified and directed.

M&L preparation of new steel surfaces of any description exc10 cm width or girth and applying two coats of synthetic enamel paint over one coat red oxide primer all as specified.

S&F 110 mm PVC SWR pipe single socketed , in an length with rubber ring joints , laid in trenches complete all as specified and as directe by Engineer-In-Charge.

M&L for preparation of newly plastered / unplastered surfaces of wall & applying two coats of cement base paint complete all as specified.

Demolition cement concrete of any description and in any position not otherwise specifically provided.

M & L for PCC 25 mm thick type B0 (1:2:4),using 12.5 mm graded stone agg as in sub base under floors complete all as specified

M&L for 40 mm thick PCC type B-1 ( 1:2:4) 20mm graded aggregate as in PCC flooring as in surface finished with out using extra cement .

M&L for Providing PCC 1:4:8 type D-2 (40mm graded agg) as in foundations filling , sub base and mass concrete all as specified.

M&L PCC 1:3:6 type C-2 using 40mm graded stone agg. ,50mm thick as in floors over stone patti roof slab finished the surface even and fair comp.all as specified.

M&L 75mm thick PCC 1:4:8 type D2 using 40mm gaded stone aggregate as in sub base of floors with finishing cement concrete surface even and smooth.

M&L for 7-8 mm thick Dark shade Vitrified ceremic tiles (square/Rectangular) polished ,area of each tiles not exceeding 0.36 Sqm as in floors over 15 mm thick screed in CM 1:6 jointed in neat cement slurrry and pointed in white cement slurry to match the shade of existing surfaces.

Ditto as per Serial item 33 above but with 10 mm thick in CM 1:4 as on vertical surface.

Taking down shutter exc 1 sqm and n exc 2 sqm each and refixing in the same opening after rescuring or easing & adjustment all as specified and directed by Engineer-in Charge.

Surface excavation n.exc. 30 cm deep and averaging 15 deep and getting out in any type of soil.

M&L Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface.

Providing and laying 60mm thick factorymade chamfered edge cement concrete paveblock of M-35 grade with approved colourdesign & pattern as in footparth, parkslawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method usingPU mould, laid in required colour & patternover and including 50mm thick compactedbed of fine sand, compacting and properembedding/ laying of inter locking paverblocks into the sand bedding layer throughvibratory compaction by using platevibrator, filling the joints with sand andcutting of paver blocks as per required sizeand pattern, finishing and sweeping extrasand; all as specified and directed.

Providing, cement concretein Type B11:2:4(20 mm gradedaggregate lintels upto 1.5m clearspan, cills, steps; seismicand other similar bandsplinth courses, string courseslacing courses, parapets andrailings upto 60 cm in heightcopings, kneelers, apex stonesbed plates, kerbs not providedfor in Item 04028, watertroughs and the like includingweathering, slightly roundedor chamfered angles andthroating, as directed

Extra for forming fair finished drain or drain channel 30 cm inner girth in cement concrete using extra cement including forms moulds mitred stopped ends etc complete all as spd.

M&L for Concrete bed to drain pipes laid to falls including packing under and haunching against the sides of pipe after they are laid and tested in cement concrete M-10 (Nominal mix) for 150mm bore pipes etc

Reinforced concrete pipes of 150mm bore class NP3, laid and jointed complete with collars as spd and tested after they are laid etc complete all as spd.

S&FNoninal 20 mm Broken brick coarse aggregate all as specified and directed.

M&L for Cement concrete M-10 (Nominal mix) using 40mm graded stone aggregates in foundation filling and mass concrete etc complete all as spd.

M&L for Cement concrete M-15 ,Type B-1 using 20mm graded stone aggregate (Nominal mix) in copings, benching and the like including weathering slightly rounded or chamfered angles as directed including necessary form work and finishig all exposed surfaces complete all as specified and directed.

Supply only integral water proofing Liqued

Pre Cast Cement Concrete (1:2:4) type B-1 using 20mm graded stone aggregates as in manhole covers,fixed in Angle Iron Frame incl all necessary formwork (Reinforcement steel measured and paid seperately)

M&L for 125 mm thick PCC (1:4:8), type D 2 using 40mm graded stone agg as in sub base of floors /Interlock tile etc finished even and rough complete all as specified and directed.

M&L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade manufactured using grey cement and pigment complete all as spcified and directed.

M&L Machine pressed precast conctete factory made interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and no pigment complete all as specified.

M&L for 25 mm thick sand filling under floors, cushioning under interlocking tiles or in foundations including watering and consolidation complete all as specified and directed.

Providing cement concrete louvres and jallis 35mm thick type B0 1:2:4 using 12.5mm graded aggregate (measured solid) including all mouldings but exc frame,set in CM (1:4) all as specified.

M&L for preparation of new surfaces plastered by brooming down or steel wire brushing scraping down oil & greasy spots etc and applying two or more coat of exterior premium acrylic emulsion paint (weather coat )of approved tint including priming coat of exterior primer over new plastered surfaces etc all as specified and directed by Engineer-in-Charge.

M&L Jodhpur stone of roof slab self faced 1.5cm to 10 cm thick 25 to 35 cm wide hoisted and set jointed and grouted in cement and sand mortar 1:6 comp.all as specified.

M&L Sand stone slab 25-35mm thick as in chhajas, sunshade , man holes covers ,plateform etc. n exc 2 m in length punched dressed on face and along exposed edges,self faced on other side and set in cement mortar 1:4 incl.making chases in wall.

M&L for 15 mm thick screed bedding in cement mortar 1: 4 on concrete surfaces, finished Fair & even including mixing water proofing compound as per manufacturer's instns( WPC to be measured separately as supply only)

Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg/sqm incl cleaning surface complete all as specified and directed.

S&F APP based polymeric membrance min weighing 3kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric land on primed surface by force application complete all as specified.

M & L Lime concrete terracing as specified on roof

M&L 40mm thick brick tiles laid on mud mortar and joints / grounting flush and jointed in CM (1:3) mixed with crude oil @ 5% by weight of cement on mud phuska,complete all as specified and directed by Engr In Charge

M&L Non skid Ceramic coloured tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors on 15mm thick screeding in CM 1:6. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete.

M & L glazed ceramic coloured tiles of size (300x450 )mm x 7/8 mm thick on vertical surface as in dados, skirting etc, set and jointed in neat cement slurry over and including 10mm thick plaster in cement mortar 1:4, pointed with white/ coloured cement to match complete all as specified and directed by Engr In Charge

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specifiecation and drawings.

S&F factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement forstyle and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site. complete all as specified.

Supply and fixing of 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified.

S&F for 150mm size aluminium anodised barrel tower bolt of extruded section and fixed.all as specified and directed.

S&F for 150mm size aluminium anodised handle of febricated type and fixed.all as specified and directed.

S&F factory made mild steel Window/ Ventilator box type with upper top hung shutters and bottom fixed type shutters including pintol hinges,steel peg stay and one shop coat of red oxide primer complete all specified. Note : i) The window shall be fabricated as per Drg No CEBTZ/TD/888R & 889 ii) Glazing, wire gauge shall be measured and paid separately

S&F 3 mm thick Frosted glass ordinary quality and glazing with oil putty in squares n exc 0.5 sqm each pane all as specified

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

S&F 75mm bore cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 1:2:4 all as specified.

S&F cast iron soil, waste and vent pipes (sand cast) 75mm bore in any length with or without ears with cement joints laid in trenches/wall including stack clamps all as specified.

S&F cast iron vent cowl for 75 mm dia pipe. all as specified.

S&F cast iron soil, waste and vent pipes (sand cast) 100mm bore in any length with or without ears with cement joints laid in trenches all as specified.

S&F Cast iron bend (any radius) diminishing pieces or tapers/ Reducers/ Sockets 100mm bore fitted with oval access door. all as specified.(Larger bore measured)

S&F Cast iron bend (any radius) diminishing pieces or tapers/ Reducers/ Sockets 75mm bore fitted with oval access door all as specified..(Larger bore measured)

S&F rotational mouleded polythene water storge tank any colour Double layer (Cylindrical vertical with closed top) hoisted and fixed in position all as specified of 500 ltr capacity .

S&F 20 mm dia of ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed, (minimum weight 20mm-210 gms) complete all as specified.

S&F stop cock with butterfly handle ,screwed both ends for iron pipe of dia 20 mm complete all as specified and directed,all as specified & directed. ISI Marked

S&F Vitreous China pedestal pattern white,(excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete all as specified and directed by Engr In Charge

S & F Plastic water closet seat cover white/coloured ,closed pattern with flat bottom pattern and cover and mild steel chromium plated or aluminium hinging device.

S&F PVC flushing cistern 10 ltrs capacity incl flushing pipe and connections complete. as approved by Engineer in charge,low level, white with inlet, ball valve ,complete including connection to pipe all as specified.

S&F Vitreous China wash basin, white, flat back, size 550x400mm including cutting for and pinning in ends of brackets or erecting stand including brackets & waste pipe etc complete all as specified.

S & F Viterous China urinal half stall type complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; white including CP spreader, waste pipe etc.

Supply and fixed 15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plqated, fancy type, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr In Charge

S&F chromium plated Bib Tap, with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule, fancy type, CP, 15mm dia

S&F15mm bore PVC connection with PTMT nuts length 450 mm

S&F fancy type chromium plated stop valve/Angle valve cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions chromium plated of size 15 mm. all as specified

S & F health faucet (ABS body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 m long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed by Engr In Charge

S&F 32 mm size CP waste coupling (half or full threaded) Minimum weight 32mm-45gms/40mm-60 gms) incl waste pipe

S&F soap dish,chromium plated fixed to wall with plugs with screws complete all as specified and directed.

Supply and laying of CPVC pipes (outer dia 16 mm) SDR 13.5 pipes & plain CPVC SDR 11 fittings on wall/ceiling or laying in floors complete all as specified and directed by Engr In Charge

Supply and laying of CPVC pipes (outer dia 20 mm) SDR 13.5 pipes & plain CPVC SDR 11 fittings on wall/ceiling or laying in floors complete all as specified and directed by Engr In Charge

Preparation of newly plastered surfaces of wall and applying two coats of distemper oil emulsion, white or tinted over a coat of putty complete all as specified and as directed by Engineer-in-Charge.

Preparing surfaces of plaster or unplaster new and applying three coat of white wash on ceiling complete all as specified and as directed by Engineer-in-Charge.

M & L RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in precast cement concrete, manhole covers/ Drain cover(vibromechenically floated ) including all use of forms, moulds or machine moulds and setting the blocks, slabs etc in cement mortar 1:4,complete all as specified and directed. (Reinforcement shall be measured and paid separately under respective item ) .(Note : Curing arrangements shall have to be made by contractor at its own with out any claim on cost incurred)

Cutting into existing manhole for connecting new drain making good to pipe and rendering cutting out existing benching for and forming branch channel(1/2 round or 3/4 section) in cement conc. 1:2:4 type B-1 smooth finished and reforming benching as required for 150mm dia of pipe.

M&L upto 150 mm dia (Internal) SGSW pipes grade 'A' laid in trenches and jointed complete all as specified and directed by Engineer-in-Charge.

M&L for providing 75 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection finished even and smooth without using extra cement complete all as specified.

Supply, laying and jointing GI tubes, medium grade 25mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches complete all as specified and directed by Engr-in-charge.

Supply, laying and jointing GI tubes, medium grade 20mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches complete all as specified and directed by Engr-in-charge.

Cutting existing steel tubing for alterations or additions done in position without taking down for 40mm to 100 dia pipe (Each cut measured)

S&F Gun metal gate valve 20mm bore with iron wheel head screwed both ends for iron pipes complete all as specified and directed .

S&F Gun metal gate valve 25mm bore with iron wheel head screwed both ends for iron pipes complete all as specified and directed for the following sizes-

Supply & Laying & commissining of LT UG cable XLPE sheathed PVC insulated, screened PVC bedded, galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volts grade, laid in tranches, in GI pipe, including brass cable glands, clamps etc of size 02 core x 10 Sqmm complete all as specifed and as directed. Make : Polycab/KEI/Havells Note: Earthwork, sand cushioning, bricks, GI pipe, etc will be measured and pad under appropriate items.

Supply and fixing GI Pipe light grade of Size 40 mm bore with all fittings for passing of cables fixed to pole/wall/laid under floor or roads including all fixing accessories complete for protection of cable all as specified and directed. Make: Jindal/ Bansl/Tata

Supply and Laying Double wall corrugated pipe(DWC pipe, Specification-120 mm OD/103 mm ID) for laying XLPE LT UG cable by DWC pipe throughout the LT cable length in pieces of convenient lenth .(Note : in pieces for easy rectification during fault ).

M & L for point wiring for one light/fan/bell/buzzer point controlled by one way switch with 1.5 sqmm single core PVC insulated and sheathed multi stranded copper conductor FRLSH cable 1100 volts grade (ISI Marked) including 1.5 sqmm single core PVC insulated and sheathed multi stranded copper conductor FRLSH cable 1100 volts grade (ISI Marked) as continues earth wire in green colour to coomon earth dolly laid/drawn into and including non metalic PVC concealed conduit (medium duty, ISI marked not less than 20 mm dia) with all fittings such as tee, bends etc all as per IS terminated in & including new modular metal flush boxes of requisite module concealed in wall for mounting fittings like modular Switches, sockets, regulators etc with and including modular cover plates with frame of requisite modules all as specified and as directed: Notes:- (i) Cost of cutting/leaving forming chases for conduit, sinking for metal flush boxes and making good in CM 1:4 shall deemed to be included in quoted rate of this item. (ii) The quoted rates of this item shall deemed for include for modular metal flush boxes of requisite module and modular cover plate with frame of requisite module of colour as approved by GE

(b) One pin 5 amps socket point on the same board with other switches complete

(c) One multi pin socket 5/6Amps, Independent.

S&F switch Modular type, 6 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.

M&L socket outlet 3 Pin 6 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.

S&F ceiling rose, surface backelite , three terminal AC, 230 volt complete all as specified.

S&F LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size omplete all as specified and directed by Engr-in-charge.

Supply and fixing LED Bldg Security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engr-in-charge.

S&F GI bracket made out of 40 mm bore GI pipe light grade /medume grade, ISI marked, medium grade 1.2m long bent to shape suitable for fixing of street light fitting including with 2 Nos MS clamps made with 40x3mm flat iron, bolts, nuts, washers etc including two coats of synthetic enamel paint over one coat of zinc chrome primer and fixing on electric pole complete all as specified and as directed by Engr-in-Charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m with blades and frame including new GI wire mesh heavy duty with wooden frame protection against birds etc including provision of cutting of existing wall for suitable opening as per fan, including electric connection with and including new 1 Sqmm, 2 core flexible copper conductor cable from ceiling rose to fan, fan hanging on wall with 4 Nos steel fastners 10mm dia 100mm long and making good the disturbed surface complete all as specified and as directed by Engineer-in-charge. Note :- Serial Number of exhaust fan issued by Engr-In-Charge and GE Office name shall also be written on fan with red colour permanent marker.

S & F double door, sheet metal enclosure, powder coated for MCB DB SPN 8 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as specified and as directed by Engr-in-charge.

S & F MCB SP, 5-32 Amps , 240 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge.

S & F MCB SPN, 5-32 Amps, 240 volts, breaking capacity 16KA complete all as specified and as dircted by Engr-in-charge.

M&L for Earthing complete with galvanized steel earth plate electrode 60cm x60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level connecting to the galvanised earth lead wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanized iron and steel earth wire protected by provision of GI mediumgrade pipe 15mm bore including provision of concrete pit made with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4Kg/Sqm) and frame of angle iron 40x 40x6 mm and handle of 6mm dia MS bar made to shape, GI light grade 20mm bore pipe for watering perforated at bottom, 1.75meter long placed on top edge of earth plate, common salt & charcoal filling with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate No -5 of SSR 2009 Part-I and connecting to Lighting protection earth test points all as specifed and directed including testing on completion.

Beenu Co. Company (BID ID -3354458)

VIJAY KUMAR SHARMA (BID ID -3352112)

Durga Construction Company (BID ID -3354179)

KAMLA CONSTRUCTION COMPANY (BID ID -3351556)

M/S BIKANER CHEMICAL LABORATORIES (BID ID -3353909)