CERTAIN REPAIR TO LEAKAGE SEEPAGE PLASTER FLOORS ROOF SUNKEN TREATMENT PLUMBING AND OTHER ALLIED SERVICES AT 510 ABW AND ADJACENT AREA UNDER AGE BR-II OF GE (NORTH) MEERUT CANTT

Amount

Demolition of cement concrete in ground floors and paving not exceeding 15cm thickness(below or above ground level) and including removal of debris & rubbish from the site complete all as specified and directed. Note : Stone slabs / tiles and hard core of any description shall not be measured & paid under this item.

Demolition stone slabs and tiles of any description or thickness in floors/ dado etc., laid bedded and pointed in any mortar, complete all as specified and directed.

Taking down cement plaster on brick walls & concrete surfaces & the like including raking out joints, hacking for key, scrubbing down with water etc., any description, including removal of rubbish outside MoD land, complete all as specified and directed.

Demolition of brick work or rubbled stone masonry including all quoins arches , pillars etc built in cement mortar and including removal from the site complete all as specified and directed.

Dismantling of floor, hearth or wall tiles / terrazzo including cement mortar bedding (but not backing),removal rubbish off the premises, complete all as specified and directed.

M&L Brick masonry with fly ash bricks straight or curved on plan exceeding 6m mean radius, old size bricks, built in Cement Mortar 1:6 complete all as specified and directed.

All as per item No. 06 here-in-before but except bricks complete all as specified and directed. Note:- Serviceable bricks retrieved from Serial item No. 4 shall be used.

M&L for PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in coping, bed block, kneels, apex stones etc including weathering slightly rounded or chamfered including form work complete all as specified and directed.

M&L for applying 15mm thick rendering using ready mix plaster bags on brick / concrete surfaces of external walls finished even and fair using water proofing compound @3% by weight of cement as per manufacturer instructions, complete all as specified an directed. Note :- Contractor is required to deposit ready mix bags for 100% CA quantity to the Engr-in-Charge within 15 days of acceptance of contract.

M&L for Rendering 15 mm thick on brick or concrete surfaces in cement mortar (1:4) finished even and smooth without using extra cement complete all as specified and directed.

M&L for Rendering 15 mm thick on brick or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed.

M&L for Rendering 10 mm thick in cement mortar (1:3), as on concrete surfaces (such as top & sides of chajjas, beams, balcony ceiling etc.) finished even and smooth without using extra cement, complete all as specified and directed. Note:- The rate quoted by contractor is deemed to be included necessary scaffolding and form work as required up to 3.50 Mtr height building.

M&L for Rendering 10 mm thick in cement mortar (1:3), as on concrete surfaces (such as top & sides of chajjas, beams, balcony ceiling etc.) finished even and smooth without using extra cement complete all as specified and directed. Note:- The rate quoted by contractor is deemed to be included necessary scaffolding and form work as required exceeding 3.5 Mtr but not exceeding 7.00 Mtr height building.

M&L for repair to overhang portion of chajja, facia, drop wall etc. for continuous work by providing PCC(1:2:4) Type B-0 and finished with CM(1:3) after taking down of damaged portion of RCC work by maintaining same level and finished the surface to match with the existing surface by providing same finish to match the existing including necessaryh scaffolding and formwork complete all as specified and directed. (Height of work to be considered above 3.5m and up to 7m from FFL of Ground Floor.) Note :- Wherever reinforcement is required to be provided will be paid separately under relevant item and contractor have to inform the department one day in advance after binding of reinforcement for measurement otherwise no payment will be considered on this account.

Supply only TMT steel bars for reinforcement in required length and dia, complete all as specified and directed.

Supply only welded steel wire fabric, weight not exceeding 4kg/sqm, complete all as specified and directed.

Demolition of cement concrete/lean concrete/brick bats from sunken portion exceeding 15cm above ground floors and removing excavated materials upto a total distance of 250 mtrs complete all as specified and directed.

Material & labour for sunken slab treatment comprising of the following :- (a) Taking out/ down old existing sunken slab treatment and cleaning the old RCC surfaces of sunken slab including removal of the rubbish from the site of work to a distance not exceeding 250m complete all as specified and directed. (b) Material & labour for 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) over cleaned sunken slab surfaces. (c) Material & labour for applying bituminous priming coat/tack coat over PCC surfaces @ 0.30 Kg per square metre of surfaces. (d) Material & labour for applying bitumen grade 85/25 over priming coat @ 1.20 Kg per Square metre. (e) Material & labour for 25mm thick plastering in CM 1:4 using water proofing compound (WPC) @ 200 ml per bag of cement. on wall of sunken floor (f) Material & labour for suitable thickness of PCC 1:5:10 type E-2 (using 40mm graded broken brick aggregate) for filling in the sunken portion of slab up to its floor level. (g) Supply & fix of 40 mm dia GI pipe medium grade, 450mm long (for draining out the water), as in spout for sunken floor, fixed as in wall, inside end fixed with wire netting & external bevelled edge at 45 degree, complete all as specified and as directed.

M&L for cutting of bushes small trees ( Peepal small plants etc) trunks shrubs of any dia and girth from roof projection, chajjas, wall junction parapet etc at any height by necessary demolition of brick work etc if required and making good disturbed surfaces to match with existing finishes with and includingmaterial and labour in cement mortar 1:4 mixed with WPC /PCC 1:3:6 type B0 (12.5 mm graded stone aggregate) / Brick work in cement mortar 1:4 as required at site and complete all as specified and as directed.

M&L for first quality, joint free non skid ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, laid in floors with neat cement slurry over and including 15 mm thick screed bed of cement mortar (1:6) including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed.

M&L for first quality, non skid ceramic coloured joint free tiles, 7 to 8 mm thick (square or rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, laid in floors set and jointed with neat cement slurry over and including 15 mm thick screed bed of cement mortar (1:6) including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed.

All as per item Srl item No 21.00 here-in-before but on vertical surfaces such as skirting fixed on and including 10mm thick rendering in cement mortar 1:4 as backing coat complete all as specified and directed.

M&L for joint free vitrified ceramic tiles light shade 10 mm thick (square/rectangular) area of each tiles not exceeding 0.36 sqm, in floors etc, with neat cement slurry over and including 15 mm thick screed bed of cement mortar 1:6 including pointing in white or coloured cement with pigment to match the shade of tiles complete all as specified and directed.

All as per item Srl item No 23.00 here-in-before but on vertical surfaces such as skirting fixed on and including 10mm thick rendering in cement mortar 1:4 as backing coat complete all as specified and directed.

M&L for first quality coloured glazed ceramic tiles, fixed in pattern of different colour including border of size 300x 450 x 7mm thick as in vertical surfaces such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles laid on and including 10 mm thick rendering in cement mortar 1:3 including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed. Note :- Pattern of the tiles will be decided by GE at the time of execution.

M&L for 18-20mm thick granite (of any type) work (table rubbed and polished) in window cills, cooking platform, shelves and the like, over and including 15mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed.

M&L for stone slabs 50 mm thick cement mortar 1:4 dressed true and square in one length not less than 60 cm and not exceeding 120 cm in copings, window cills, chajjas, sunshades etc punched dressed on exposed faces and self faced on the embedded unexposed beds and joints exposed edges round or chamfered , set, jointed and pointed in mortar as in plinth protection complete all as specified and directed.

M&L for providing Cement concrete 1:2:4 Type B 2 (using 40 mm graded crushed stone aggregates), in foundations, filling and mass concrete complete all as specified and directed.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L for 20-25mm thick machine cut kota stone slab as in flooring, steps of stair(treads), set with neat grey cement slurry laid over and including 20mm thick cement and sand mortar 1:6 screed bed/bedding layer, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for machine cut kota stone slab 18-20mm thick as in skirting/dado, riser of steps, laid over and including 10mm thick backing coat in cement mortar 1:4, set in neat grey cement slurry and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed.

Rounding to edges of stone slabs one edges such as in steps, cooking platform and other similar situations complete all as specified and directed.

M&L for reinforced cement concrete 1:1.1/2 = 3 type B-1 using 20mm graded crushed stone aggregates as in slabs supported on walls, beams and columns, shelves and the like work, complete all as specified.

M&L for mild steel TMT bars 10mm dia and over, cut length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia quality conforming to Fe- 415, Fe 500 or Fe-550 as in steel reinforcement for concrete complete all as specified and directed. Note :- Weight of binding wire shall not be considered for measurement and payment purpose.

M&L for form work to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work; with rough finished surfaces of concrete, complete all as specified and directed.

S&F in repairs packing rubber washer of wall and WHB mixer complete all as specified and directed

S&F in repairs bib taps, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for 15mm bore iron pipe complete all as specified and directed.

S&F in repairs angle cock/stop valves, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 15 mm bore iron pipe or for brass ferrule complete all as specified and directed

S&F in repairs stop valves, cast copper alloy, chromium plated, fancy type, with long shank and cup (concealed type), screwed down, high pressure, with crutch or butter fly handle, screwed both ends for 15mm bore iron pipe or for unions complete all as specified and directed.

S&F in repairs 15mm dia gun metal gate valve, with iron wheel head, screwed both ends for iron pipes complete all as specified and directed.

S&F in repairs 20mm dia gun metal gate valve, with iron wheel head, screwed both ends for iron pipes complete all as specified and directed.

S&F in repairs PVC connections fiber reinforced 15mm size with PTMT nuts of length 300mm suitable for hot water complete all as specified and directed.

S&F in repairs PVC connections fiber reinforced 15mm size with PTMT nuts of length 300mm complete all as specified and directed

S&F in repairs CP waste coupling of size 40mm for sink complete all as specified & directed.

S&F in repairs brass CP waste coupling of size 32mm for WHB with long screwed shanks and fly nuts complete all as specified & directed.

S&F in repairs 32mm dia PVC waste pipe for WHB 60cm long with union complete all as specified and directed.

S&F in repairs 40mm dia PVC waste pipe for Sink 60cm long with union complete all as specified and directed.

M&L in repairs brass spindles for 20mm CP brass bib cock / stop cocks / pillar tap / angle wall mixer etc half or full turn of any description suitable for MAP Qtrs complete all as specified and directed.

S&F in repair plain FRP sheeting at north light curves, roofs, window, duct covering or at any other location by coach screw and washer, nut & bolt, staple pins or any other suitable means complete all as specified and directed. Note : To be fixed in patches as specified and directed by Engg-in-Charge and ht of bldg >10m

S&F in repair CP brass toilet paper holder complete all as specified and directed.

S&F in repair 15mm dia, 50mm long GI nipple, suitable for HDPE water tanks complete all as specified and directed

S&F in repair 20mm dia, 50mm long GI nipple, suitable for HDPE water tanks complete all as specified and directed

S&F Grating 100 mm dia of PTMT fixed on floor/ nahani trap with cement mortar, fixed in repairs, complete all as specified and directed.

Supplied and fixed in repairs MS CP grating 125 mm dia over floor / Nahani traps complete all as specified and directed.

S & F in repairs 15mm ball valve, high pressure of PTMT with epoxy coated aluminum rod and high density plastic ball, screwed for iron pipe (Minimum weight 142 gms) complete all as specified and directed.

S & F in repairs 20mm ball valve, high pressure of PTMT with epoxy coated aluminum rod and high density plastic ball, screwed for iron pipe (Minimum weight 210 gms) complete all as specified and directed.

S&F in repairs bib tap standard of PTMT any colour high pressure screwed for iron pipe or brass ferrule of 15 mm bore and fixed (Minimum weight 90 gms complete all as specified and directed.

S&F in repair stop valve of PTMT any colour high pressure screwed for iron pipe of 15 mm bore and fixed. (Minimum weight 15mm- 90gms/20mm-92gms) complete all as specified and directed.

S & F in repairs 10 liters capacity, PVC valve less, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and suitable flush pipe PVC 32mm dia complete all as specified and directed.

S&F Vitreous China wash down water closet (pedestal pattern), white (excluding fixing bolts flushing cistern and flush pipe), fixed in repairs, including connection to waste pipe, flushing pipe, anti-syphonage pipe etc. and making good to floor complete all as specified and directed.

S&F Plastic water closet seat cover black/ white closed pattern with flat bottom and cover and mild steel chromium plated or aluminum hinging devices, fixed in repairs, complete all as specified and directed.

S&F in repairs 8mm dia, brass chromium plated health faucet with 1 meter long flexible hose and wall hook complete all as specified and directed.

S&F Towel rail 600 mm long, 20 mm dia, ‘D’ type, brass, chromium plated, fixed to walls with screws and plastic cleats, fixed in repairs, complete all as specified and directed.

S&F Towel ring 20 mm dia, round brass, chromium plated, fixed to walls with screws and plastic cleats, fixed in repairs, complete all as specified and directed.

S&F in repairs vitreous china squatting pan, 'Orissa' pattern, size 580x440mm white, with integral foot rests, including 100mm cast iron 'P' or 'S' trap and 100mm cast iron sanitary connection socket to fit WC outlet including connection to trap, to flushing pipe, anti-syphonage pipe etc. complete including making good to floor to match the existing complete all as specified and directed.

S&F in repair CP Brass Soap Dish complete all as specified and directed.

S&F in repairs Wash basins, vitreous china, white, flat back of size 550x400mm including brackets and cutting for and pinning in ends of brackets or erecting stand 32mm dia waste fittings, brass, chromium plated with long screwed shanks and fly nuts, 32mm dia HDPE waste pipe and including new brackets complete all as specified and directed.

S&F in repairs waste coupling of PTMT of size 32 mm half or full threaded complete all as specified and directed.

S&F for PVC heavy duty waste pipes of 40/32 mm dia suitable for wash basin/ sinks complete all as specified and directed.

Dismantling of PVC water storage tanks of capacity exceeding 250 liters but not exceeding 500 liters, including removal of rubbish outside MoD land complete all as specified and directed.

Dismantling of PVC water storage tanks of capacity exceeding 500 liters but not exceeding 1000 liters, including removal of rubbish outside MoD land complete all as specified and directed.

S&F Rotational molded polyethylene, double layered, water storage tanks of capacity 500 liters (cylindrical vertical with closed top), ISI Marked, hoisted and fixed in position complete all as specified and directed.

S&F Rotational molded polyethylene, double layered, water storage tanks of capacity 1000 liters (cylindrical vertical with closed top), ISI Marked, hoisted and fixed in position complete all as specified and directed.

M&L for 2 mm thick MS plain sheet for making modified lid of water tank and fixed with 04 nuts and bolts for water tanks for water capacity not exceeding 750 ltr fixed in repair complete all as specified and directed

Taking up or down steel tubing and connections 15mm dia pipes and removal complete all as specified and directed.

Taking up or down steel tubing and connections 20mm dia pipes and removal complete all as specified and directed.

S&F 15mm dia steel water tubing medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, concealed/surface fixed to walls and ceiling or laid in floors complete all as specified and directed. Note :- Cutting chases as required shall be measured and paid separately.

S&F 20mm dia steel water tubing medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, concealed/surface fixed to walls and ceiling or laid in floors complete all as specified and directed. Note :- Cutting chases as required shall be measured and paid separately

M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth, including removal of rubbish outside MoD land complete all as specified and directed.

M&L Cutting holes into or through brick/ concrete walls built, in cement mortar, exceeding 150 Sqcm but not exceeding 400 Sqcm in superficial area and making good in cement mortar 1:3 to match with the existing finishes complete all as specified and directed.

Refixing old steel tubing and connections 15mm dia in new or old position including cleaning of old tubes (walls, ceiling, floors etc) complete all as specified and directed.

Refixing old steel tubing and connections 20mm dia in new or old position including cleaning of old tubes (walls, ceiling, floors etc) complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) bends any radius complete all as specified complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) bends any radius complete all as specified complete all as specified and directed.

S&F in repairs UPVC (SWR) floor trap 75 mm bore including jointing to waste pipe with cement solvent fixed in cement concrete complete all as specified and directed.

S&F in repairs PVC (SWR) gully trap 125/100 mm bore setting and jointing with solvent cement complete all as specified and directed.

S&F in repair hollow PVC wall lining consisting of 5mm thick plain color PVC sheet including of solvent cement and fixing at site on PVC frame if required as per specification and drawing complete all as specified and directed.

S&F in repair 75 mm bore UPVC(SWR) pipes single socketed in any length with rubber ring joint laid in trenches/under floor complete all as specified and directed.

S&F in repair 110mm bore dia UPVC(SWR) pipes single socketed in any length with rubber ring joint laid in trenches/under floorcomplete all as specified and directed.

S&F in repair in fancy type brass CP hot and cold centre hole wash hand basin mixture swan neck, 15 mm bore screwed down high pressure with long screwed shanks and fly nuts screwed to iron pipe complete all as specified and directed. MAKE :- Pearl Cat part No ARI-013, PRAYAG-LAGUNA -9350.

Excavation in trenches in soft/loose soil not exceeding 1.50 meter wide and not exceeding 1.50 meter deep for foundations etc. or for cesspits etc. and not exceeding 10 Sqm on plan and not exceeding 1.5 meter in depth and getting out complete all as specified and directed.

Returning, filling in, of soft/loose soil, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick each complete all as specified and directed.

Removing excavated materials not exceeding 50m and depositing where directed at a level not exceeding 1.5 meter above the starting point in soils, complete all as specified and directed.

Taking down shutters of any description not exceeding 1 Sqm each, from chowkhat, complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sq. m each, from chowkhat, complete all as specified and directed.

Taking down Chowkhats with shutters without taking of shutter from the frame of any description not exceeding 1.50 Sqm each, and making good the disturbed Surface in cement mortar 1:4 & finished with similar specification as exists, complete all as specified and directed.

Taking down Chowkhats with shutters without taking of shutter from the frame of any description exceeding 1.50 Sqm but not exceeding 4.00 Sqm each, and making good the disturbed Surface in cement mortar 1:4 & finished with similar specification as exists, complete all as specified and directed.

Resecuring or easing and adjusting without taking down shutter from the frame & refixing builders hardware as required including removal of unserviceable screws etc. not exceeding 1 Sqm each complete all as specified and directed.

Resecuring or easing and adjusting without taking down shutter from the frame & re-fixing builders hardware as required including removal of unserviceable screws etc. area exceeding 1 Sqm but not exceeding 2 Sqm each, complete all as specified and directed.

S&F Factory made shutter, 35 mm thick, 2nd class hardwood (Hollock) rail and style, plain framed, paneled shutter (two panel) with lock rail and panel of 9 mm BWP commercial ply. The size of rail and stile as per IS: 1003 (Part-I) and as specified in SSR Part-I section 8 clause 8.24(a), kiln seasoned and chemically pressure treated, complete all as specified and directed.

S&F 35 mm thick 2nd class hardwood (Hollock) skeleton shutters, open rebated and prepared to receive wire cloth, glass etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass, wire cloth etc., sizes of members of shutters as specified in SSR Part-I section 8 clause 8.24(a), complete all as specified and directed.

S&F Factory made flush shutters 30 mm thick, ISI marked, solid core construction, with block board core and plywood face panels, commercial type on both faces, complete all as specified and directed.

S&F Factory made PVC solid door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of 5 mm thick plain colour PVC sheet cut at corner and jointed with 02 Nos., 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge (EPDM) rubber gasket weather seal provided throughout the frame and fixed to wall with 65/100 mm long mild steel screws through the frame by using PVC fasteners (minimum of 04 Nos. of screws to be provided for each vertical member & minimum 02 Nos. for horizontal member), complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined to gether with solvent cement, suppling & fixing in the frame at site as per specification & drawing on srl page No 174 of SSR Part-II complete all as specified and directed.

S&F Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, 100 mm, ISI marked, complete all as specified and directed.

S&F 150mm long aluminum anodized, barrel tower bolt of extruded section complete all as specified and directed.

S&F 150mm size aluminum handle fabricated, 'D' type, anodized ISI marked complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to steel frames with tinned tacks, or galvanized wire staples, or fixed to wooden frames with first class hard wood bead, complete all as specified and directed.

S&F in repairs, stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to steel frames with tinned tacks, or galvanized wire staples, or fixed to wooden frames with first class hard wood bead, complete all as specified and directed.

Hacking out old broken glass (any thickness size, quality or description) from wooden/ steel frames, glazed with putty or fixed with wooden beads/ metal pins complete all as specified and as directed.

S&F 3mm thick Sheet glass ordinary quality and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

S&F 3mm thick figured glass, pin headed type and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

S&F in repair for 4.8 mm thick sheet glass, ordinary quality and glazing with oil putty or rubber beading or by any other means as per requirement in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F 25 mm dia stainless steel curtain rod with fancy type bracket and ring ( 08 Nos/ RM) complete all as specified and as directed.

M&L for welding in repair of loose joints of trusses, purlins, rafters, cleats, sliding doors, flat iron supports for valley gutters, windows, doors, north light framing etc inc at any height & inc necessary cutting and grinding complete all as specified and directed

S&F for Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders framed balusters; walk ways; railings; and similar work conforming to Fe-290 Gde-E-165, complete all as specified and directed.

S&F in repairs aluminum (extruded section body) door closer hydraulically regulated, designation No 3 universal type suitable for door shutter of 851 to 1000mm in width and of weight between 61 to 80 Kg and fixed complete all as specified and directed.

M&L for Cutting holes in brick walls exceeding half brick but not exceeding one brick built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or PCC 1:2:4, including removal of rubbish outside MoD land, complete all as specified and directed.

Dismantling mild steel work of any description not otherwise provided for complete all as specified and directed.

Demolition of cement concrete (reinforced) as in roofs, floors, beams, staircase landing, chajjas, balconies and similar suspended work chajjas, facia and the like complete all as specified and directed.

S&F 1 mm mild steel, plain black sheet in steel gate or similar work, cut to size, holes punched, including round headed screws, clout nails or rivets and fixed to steel framing with riveted or welded seams, including bending or turning up complete all as specified and directed.

M&L for Three coats of white wash including preparation of new plastered wall surfaces of any description complete all as specified and directed.

M&L for Preparation of newly plastered surfaces of wall and applying two coats of cement base paint complete all as specified and directed.

M&L for Preparation of old plastered or unplastered surfaces of wall and applying one coat of cement base paint complete all as specified and directed.

Material and labour preparation of new plastered surfaces and apply two coat of oil bound distemper over a coat of primer & chalk whitening & smoothening of surface, complete all as specified and directed.

M&L for preparation of newly plastered surface of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for Preparation of new or previously untreated wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of new surfaces of steel and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for Preparation of old painted wooden surfaces over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for Preparation of old painted steel or iron surfaces over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for Preparation of old surfaces of walls including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc. and applying one coat of white wash, complete all as specified and directed.

M&L for Preparation of old surfaces of ceiling including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc. and applying one coat of white wash, complete all as specified and directed.

M&L for Preparation of old surfaces of walls including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc.; rubbing down and stopping of surfaces using sand paper and applying one coat of oil bound distemper, complete all as specified and directed by the Engineer-in-Charge.

M&L for providing precast RCC 1:2:4 type B-1 using 20mm graded stone aggregate) as in cover slab chullah hoods, chajjas, water troughs, shelves or similar works set & jointed in CM 1:4 complete all as specified and directed.

S&F steel windows with pressed steel frame made out from 1.25 mm thick steel with one or more rebate with glazed shutters and fly proofing shutters including guard bars, hinges, peg stay , handles tower bolts lugs including treated with tar or coal tar black paint on steel surfaces in contact / embedded in concrete / masonry work complete all as specified and directed. Note : (Disturbed surfaces of wall shall be made good to true surface)

S&F in repairs Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminum alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed.

S&F anodized aluminum snap grid frame work for size of grid 605x605 mm for false ceiling complete all as specified and directed.

S&F in repairs valley gutter made out of 1.25mm thick PGI sheet, with grade of zinc coating 275 gm/ sqm (both sides) including GI trough both sides of valley gutter and bottom provided with 150mm outlet projected up to 200 mm suitable to be coupled with GI rain water pipe and drilled for proper connection with trough, joints shall be welded by gas welded complete all as specified and directed .

S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with hot dip galvanised self drilling and self tapping screws neoprene and EPDM washers complete all as specified, directed and as per manufacturer's instructions. Note : Height of building >10m & there is no staircase to reach at the top of building

S&F pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws neoprene and EPDM washers complete all as specified, directed and as per manufacturer's instructions Note : Height of building >10m & there is no staircase to reach at the top of building

S&F fiber cement colored textured designer ceiling board 4mm thick of size 595x595 mm conforming to IS : 14862 & IS : 2380 Part-XIV fixed to timber / GI / Aluminum frame work with screws/clips complete all as per manufactures instructions and as directed. Make : Everest, Charminar, UPAL.

S&F in repair single lever CP 15 mm pillar tap for WHB complete all as specified and directed. Make : Jaquar Cat: CON-CHR-123BKN or equivalent in CERA

M&L for cleaning the roof surface including taking out vegetation, debris and previous treatment on roof completely inc removal of screed bed/ concrete bed/ plaster/ mud phuska or any other treatment carried out previously over roof surface and making the mother slab (Roof slab) complete visible prior to carrying out any other treatment complete all as specified and directed.

M&L for repairing the cleaned surface through repair mortar and applying priming coat of epoxy primer with resin and hardener in 1:3 ratio with water dilution as per manufacturer instructions, applying 2 coats of solvent based Polyurethane liquid applied membrane not less than 500 micron thick UV stable having SRI value greater than equal to 105 with consumption of 0.61 kg/sqm (each coat), 2nd coat should be applied once 1st coat becomes dry completely all as specified and directed. Make: Asian Paints\ Thermax. Note:- (a) The work under this item shall be carried out by the authorized applicator of Manufacturer by using modern techniques. The contractor shall also furnish warranty of quality, finish work and effectiveness of waterproofing treatment under this item for a period of 10 years from the date of completion along with manufacturer warranty of material for the same period. (b) Ht. of bldg can be more than 10 meters with no staircase to reach at the top of the building. (c) Second coat must be applied when 1st coat is completely dry and approved by engg-in-charge.

M&L for cement concrete type B-1, 1:2:4 using 20mm graded aggregate as in flooring, roof padding etc complete all as specified and directed.

S&F in repair vitreous china urinal bowl, flat back of size 465x355x265mm (minimum) white with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; grating and Union for discharge pipe and waste pipe complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern) one piece wall mounted type (inch flushing cistern) including connection to drain to outgoing pipe and to flushing pipe antisyphonage pipe etc & S&F plastic water closet seat cover closed pattern with flat bottom and MS chromium plated or aluminised hinging device complete all as specified and directed. Make : CERA Cat No S1013178 or equivalent in Jaquar /make in PS

Dismantling AC sheet corrugated or semi corrugated sheet of any description as in roof and including removal from the site complete all as specified and directed. Note : Height of building >10m & there is no staircase to reach at the top of building

Dismantling of wall or ceiling board (fiber,pulp,insulation etc) any thickness including cover fillets and removal from the site complete all as specified and directed.

Dismantling of pre painted GI Sheet / ridge of thickness 0.5mm fixed at roof of building. Note : Ht of building is more 10m and there is no staircase to reach at the top of building

M&L for refixing (except sheet) 6mm thick serviceable AC sheets using L or J hooks corrugated or semi corrugated in roofs, well etc. Note : Height or building >10m & there is no staircase to reach at the top of building.

M&L for providing cement concrete 1:2:4 type C-1 (using 20mm graded stone aggregates) as in coping, gola at the sheets and side wall top of building, kebs, holdfasts and at any other location complete all as specified and directed

S&F anodised powder coated aluminum frame for doors, windows, ventilators with one or more rebates with and including joining cleat for fixing etc complete all as specified and directed.

S&F anodised powder coated aluminum door shutters, aluminum section weighing 0.55 kg/m with and including necessary joining cleats, glazing clips, rubber neoprene packing, extruded anodised aluminum alloy fabricated type handles of size 150mm 2 Nose is each door, stainless steel hinges anodised aluminum snap beading for fixing glass panes /other filling material in panels, screws etc complete all as specified and directed. Note :- Glass panes / other filling materials in panels shall be measured and paid separately.

S&F anodised powder coated aluminum window and ventilator shutters, side hung type without sash bars aluminum section weighing 0.55 Kg/RM with and including necessary joining cleats, glazing, clips, rubber packing, anodised aluminum snap beading for fixing glass panes screws anodised aluminum fittings such as peg stays 150mm long (1 no) hinges type B-21 100mm long (2 No), extruded anodised aluminum alloy fabricated type handles of size 100mm 1 Nos complete all as specified and directed Note :- Glass panes in panes in panels shall be measured and paid separately.

M&L for fixing self tapping screw in 0.5mm thick galvalume Aluminum coated sheet complete all as specified and directed. Note : Ht of bldg is more than 10 meters and there is no staircase to reach at the top of building

S&F in repair 5 mm thick glass looking mirror of size 700mmX500mm with double coat for protection and longevity Grounded edges for safety and silver plating on the back for better reflection complete all as specified and directed. Make : CERA Cat: B3510110, B3510106, B3510111.

Supply only Integral water proofing compound (I.S.I marked on packing) complete all as specified and directed.

Repairs of petty in nature to anodised aluminum door shutters, and necessary joining cleats, glazing clips, rubber neopene packing, extruded anodised aluminum alloy fabricated type handles of size 150mm 2 Nos is each door, stainless steel hinges anodised aluminum snap beading for fixing glass panes /other filling material in panels, screws etc complete all as specified and directed. Note :- Glass panes / other filling materials in panels shall be measured and paid separately.

SA construction co.

Arun Construction Co.

B.K.construction