ADDN/ALTN CUM SPECIAL REPAIR TO DPDO OFFICE AT KANPUR CANTT UNDER GE (I) KANPUR

Amount

Taking down cement plaster on wall & ceiling including raking out joint, hacking for key scrubbing down with water etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the permises complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description including cast-in-situ terrazzo (below or above ground level), not exc. 15 cm thickness, including removal of rubbish outside MoD land, complete all as specified and directed.

M&L for 15mm thick rendering of brick wall in CM 1:6 finished even & fair on other than fair faces complete all as specified and directed.

M&L for 15mm thick rendering on fair faces of brick wall in CM 1:4 finished even & fair with using WPC complete all as specified and directed. Note: WPC shall be measured and paid separately.

M&L for 10 mm thick cement plaster on ceiling in CM 1:3 finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls applying 2 coats of oil bound distemper over and including a coat of wall care putty 1 mm thickness. The paint will be applied through aireless spray techonology with max working pressure of 3300 PSI by Trucare Graco machine / Airless paint sprayer (Vands Engineering solutions) / Airless sprayer machine Surya 9 (Jaguar) / Control Pro 190 Air paint sprayer (Wagner) and capable of operational single spray gun with a maximum materials hose length 150m working complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls applying two coats of exterior weather proof anti algae 100% acrylic emulsion over and including a coat of exterior water based primer. The primer and paint will be applied through aireless spray techonology with max working pressure of 3300 PSI by Trucare Graco machine / Airless paint sprayer (Vands Engineering solutions) / Airless sprayer machine Surya 9 (Jaguar) / Control Pro 190 Air paint sprayer (Wagner) and capable of operational single spray gun with a maximum materials hose length 150m working complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling applying 2 coats of oil bound distemper over and including a coat of primer. The primer and paint will be applied through aireless spray techonology with max working pressure of 3300 PSI by Trucare Graco machine / Airless paint sprayer (Vands Engineering solutions) / Airless sprayer machine Surya 9 (Jaguar) / Control Pro 190 Air paint sprayer (Wagner) and capable of operational single spray gun with a maximum materials hose length 150m working, complete all as specified and directed.

Complete removal of existing treatment i.e. white wash, colour wash, cement paint etc. on wall with help of hand opeated sander or by manual where it is feasible and preparing the surfaces smooth including applying a coat of wall care putty 1 mm thick with 2 coats of oil bound distemper by Trucare Graco machine / Airless paint sprayer (Vands Engineering solution) / airless sprayer machine surya 9 (Jaguar) / control pro 190 air paint sprayer (wagner) and capable of operational single spray gun with a maximum materials hose length 150m working complete all as specified and directed.

Complete removal of existing treatment ie white wash,colour wash, cement paint etc on with help of hand operated sander or by manual where it is feasible and preparing the surface of walls applying two coats of exterior weather proof anti algae 100% acrylic emulsion over and including a coat of exterior water based primer. The primer and paint will be applied through aireless spray techonology with max working pressure of 3300 PSI by Trucare Graco machine / Airless paint sprayer (Vands Engineering solutions) / Airless sprayer machine Surya 9 (Jaguar) / Control Pro 190 Air paint sprayer (Wagner) and capable of operational single spray gun with a maximum materials hose length 150m working complete all as specified and directed.

Complete removal of existing treatment i.e. white wash, colour wash, cement paint etc. on ceiling with help of hand opeated sander or by manual where it is feasible and & leveling/ edging the disturbed places/edges using necessary filling of wall care putty preparing the surfaces smooth and applying 2 coats of oil bound distemper over a coat of primer by Trucare Graco machine / Airless paint sprayer (Vands Engineering solution) / airless sprayer machine surya 9 (Jaguar) / control pro 190 air paint sprayer (wagner) and capable of operational single spray gun with a maximum materials hose length 150m working complete all as specified and directed.

M&L 25 mm thick, PCC (1:2:4) type BO (using 12.5 graded stone aggregate) complete all as specified and directed.

M&L for Non-skid Ceramic tiles 7 to 8 mm thick (square /Rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured in white or coloured cement to match with tile laid over and including screed bed or bedding layer 15 mm thick in CM (1:6) complete all as specified and directed.

M&L for double charged vitrified tiles 9 to 10mm thick (square/rectangular) in any pattern area of each tiles not exceeding 0.36 sqm, as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match etc over and including 15 mm thick screed in cement mortar 1:6 complete all as specified and directed.

M&L for double charged vitrified tiles 9 to 10mm thick (square/rectangular) in any pattern area of each tiles not exceeding 0.36 sqm, as in skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match etc over and including 15 mm thick screed in cement mortar 1:6 complete all as specified and directed.

M&L first quality coloured glazed ceramic, joint free tiles fixed in pattern of different colour including border of size 300x450x7 mm thick as in vertical surfaces such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles laid on and including 10 mm thick rendering in cement mortar (1:3), including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed. Note :- Pattern of the tiles will be decided by GE at the time of execution.

Taking down chowkats or frames with shutters (with out taking off shutters from the frame) not exceeding 1.50 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters without taking off shutters from the frame exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of decorative type/wood grain printed colour of size 50 X 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

All as per item No 20 above, but size 50 x 125mm completed all as specified and directed.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type/wood grain printed colour flush door shutter of size 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistureproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and directed.

S&F 30mm thick plain WPC factory made wire mesh solid door shutter (confirming as per Is 4020) with density not less than 600 KG/Cum Manufactured by an ISO 9001-2015 certified company. The door to be panned with SS mosquito mesh for additional strength and safety purpose Door should be fixed with SS hinges and SS screw Door should be water proof fire retardant and having screw holding capacity complete all as specified and directed. Note:- Wire cloth used shall be of 0.36 mm nominal dia and average width of aperture 1.40mm.

S&F solid PVC Moulded door frame of size 50 mm x 47 mm made out of 5 mm single side prelam PVC sheet reinforced with MS Square tube edges will be painted to match with prelam sheet as per specification & drawing incl. making good the damaged wall with plaster or concrete complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded prelam PVC Sheet on the front face & 2mm prelam PVC sheet on back face as per specification complete all as specified and directed.

S&F 150 mm stainless steel handle with SS screws etc. complete all as specified and directed.

S&F 125 mm stainless steel handle with SS screws etc. complete as per direction of Engineer-in-charge.

S&F 200 mm stainless steel barral tower bolt of extruded section complete all as specified and directed.

S&F in repair 150 mm stainless steel barral tower bolt of extruded section complete all as specified and directed.

S&F 300 mm long aluminum anodized sliding door bolt with hasp and staple and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fixed complete all as specified and directed.

S&F stainless steel Butt hinges medium weight cold rolled of 100 mm size and fixed complete all as specified and directed.

S&F stainless steel Butt hinges medium weight cold rolled of 125 mm size and fixed complete all as specified and directed.

S&F 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F of 75mm long aluminum anodised extruded type door stopper of double legged with rubber shoes in bottom complete all as specified and directed.

Supplying and fixing of Unplasticised Poly Vinyl Chloride (UPVC) 3 track sliding Window with mesh shutter - (2-glass shutter and 1-mesh shutter) duly manufactured using UPVC reinforced profiles (Composition of profile shall consists a minimum of 5.5 PHR of TiO2 and not more than 12 PHR of CaCo3 for every 100 parts of PVC resin) of (108 mm x 45 mm) x 2.20 mm for outer frames, (39 mm x 58 mm) x 2.20mm for sliding shutter frames capable of mounting single glazing system structurally reinforced with hot dip galvanized up to 50 microns of minimum thickness of 1.0/1.2 mm prefabricated & welded through fusion welding. The window sash shall be fitted with 5 mm thick clear float glass of reputed make and mesh shutter frame shall be (39 mm x 58 mm) x 2.0 mm fitted with Vinyl Coated Fiber mesh- on rollers/ pulley duly fixed with Grey colour TPV Gasket for sash & Glazing bead shall be co-extruded with Grey colour soft PVC. Window shall be provided with standard hardware & Single point locking system of touch Lock system. the system is to be installed at the site using anchor fasteners, silicon rubber sealant, easy glazing/deglazing at site etc., including cost and conveyance of all materials, accessories, labour charges for transportation, erection at site complete for finished item of work. NOTE: Cost of ss wire mesh and 5mm clear glass is deemed to be inclusive in this item.

S&F Framed work such as grills, grating etc. with ends of bars shouldered and / or riveted or forget into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

S&F 3mm thick figured glass, pin headed type and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sq. m in each pane complete all as specified and directed.

S&F powder coating (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 No.) suitable handle (1 No.) complete all as specified and directed.

S&F, Fancy type stainless steel curtain rods of 25 mm dia , as in doors/ windows pelmets including SS brackets and SS funnels complete all as specified and directed.

Taking down steel tubing/ PVC 15mm bore and connections including cleaning for refixing or removing to stores complete all as specified and directed.

All as per Item No 41.00 above but 20mm bore complete all as specified and directed.

S&F 15mm dia tubes medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, concealed/surface fixed to walls and ceiling or laid in floors complete all as specified and directed. Note : Cutting chases as required shall be measured and paid seperately.

S&F 20 mm dia tubes medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, concealed/surface fixed to walls and ceiling or laid in floors complete all as specified and directed. Note : Cutting chases as required shall be measured and paid seperately.

Cutting chases, pinning in brick walls, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels, etc; and cuttings chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exceeding 10 cm girth complete all as specified and directed.

S&F in repairs vitreous china wash basin, white, flat back, size 550x400mm , PVC connections suitable for hot and cold water,waste coupling (with internal partition) 32 mm size with 300mm &190mm long wall connection pipes & wall flange, and fixing with brackets/bolts including cutting and pinning in etc complete all as specified and directed.

S&F vitreous china wash basin, white, flat back, size 550x400mm , PVC connections suitable for hot and cold water,waste coupling (with internal partition) 32 mm size with 300mm &190mm long wall connection pipes & wall flange, and fixing with brackets/bolts including cutting and pinning in etc complete all as specified and directed.

S&F in repair 15mm bore bib tap long body, fancy type chromium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for brass ferule and fixed complete all as specified and directed. Cat No- HT F3001152 of Cera/ CON -107KN of Jaguar/ K-20073IN-4-CP of KOHLER or eqivalent make.

S&F 15mm bore bib tap long body, fancy type chromium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for brass ferule and fixed complete all as specified and directed. Cat No- HT F3001152 of Cera/ CON -107KN of Jaguar/ K-20073IN-4-CP of KOHLER.

S&F repair 15mm bore angular stop valve chromium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. Cat No - HT F3001201 OF CERA/ CON-053KN of Jaguar/ K-11568IN-7B-CP of KOHLER.

S&F 15mm bore angular stop valve chromium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. Cat No - HT F3001201 OF CERA/ CON-053KN of Jaguar/ K-11568IN-7B-CP of KOHLER.

S&F in repair 15mm bore angle valves,fancy type two way chromium plated with long shank and cup screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F 15mm bore angle valves,fancy type two way chromium plated with long shank and cup screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F 15mm bore PVC connection 600mm long heavy duty with brass fly nut and warsher for hot and cold water complete all as specified and directed.

S&F in repair 15 mm dia brass chromium plated pillar tap fancy type with fly nut capstan head screwed for 15 mm dia pipe complete all as specified and directed.

S&F 15 mm dia brass chromium plated pillar tap fancy type with fly nut capstan head screwed complete all as specified and directed.

S&F in repairs WC squatting pan “Orissa Pattern” of size 580 x 440 mm white with integral foot rest (excluding flushing cistern & flush pipe) including connection to trap and to flush pipes etc and lime concrete bedding complete all as specified in SSR and including trap set complete all as specified and directed.

S&F vitreous chinaware EWC padestal type closet with white seat including cover with flat bottom with hinging device complete all as specified and directed.

S&F in repair Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) including providing and fixing plugs, beddings urinals against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete as specified and directed.

S&F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe), complete including providing and fixing plugs, beddings urinals against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed.

S&F waste pipe for Sink/WHB/Urinal, length exc 0.75m complete all as specified and directed.

S&F in repairs CP health faucet including tube 1.2 mtr long complete all as specified and directed.

S&F CP health faucet including tube 1.2 mtr long complete all as specified and directed.

Dismantling water tanks and remove to store capacity exc 250 ltrs and n exc 500 ltrs complete all as specified and directed.

S&F HDPE triple layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 500 litres capacity hoisted and fixed in position all as specified in SSR Pt-I including for hoisting into position either inside or outside of building, connecting up pipes, securing access cover, float valve,tank adaptor etc including GI nipple of suitable size complete all as specified and directed.

S&F in repair ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball with minimum weight 210 gm screwed for 20mm bore dia iron pipe complete all as specified and directed.

M&L ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball with minimum weight 210 gm screwed for 20mm bore dia iron pipe supplied complete all as specified and directed.

S&F Towel rail 20mm dia, 60cm long brass chromium plated with brackets complete all as specified and directed.

S&F in repair 10 ltrs capacity low level PVC flushing cistern, valveless, symphonic type, white,with inlet,ball float and handle including brackets complete all as specified and directed.

S&F 10 ltrs capacity low level PVC flushing cistern, valveless, symphonic type, white,with inlet,ball float and handle including brackets complete all as specified and directed.

Demolition of brick work or rubbled stone masonry including all quoins arches, pillars etc built in cement mortar and including removal from the site complete all as specified and directed.

M&L for Cement concrete Type C2 1:3:6 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

S&F Joist, channel, angle, or tee sections, Fe 410 -W (Gde- E- 250) quality- A fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) complete all as specified and directed.

S&F for Plates (plain or chequered) Fe 410 -W (Gde- E- 250) quality- A channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed.

S&F for Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for preparation of new surfaces of steel or iron work of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over and including a coat of primer on steel surfaces complete all as specified and directed.

S&F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof overing/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L Brick work with sub class 'B' Bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 complete all as specified and directed.

S& F 100 mm CI soil waste and vent pipes single socketed in any length with cement joints laid in floor or in trenches complete all as specified and directed

S&F 75mm dia CI soil waste and vent pipes ISI marked single socketed in any length with cement joint laid in trenches or in floor complete all as specified and directed

S&F 100mm dia CI soil waste and vent pipes ISI marked single socketed in any length with cement joints fixed on walls complete all as specified and directed

S&F stack clamps out of 50mm by 5mm flat iron and 16mm dia iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75/100 mm bore of pipe complete all as specified and directed.

S&F 100mm bore Cast iron bend/shoe any radius, complete all as specified and directed

S&F 75mm bore Cast iron bend/shoe any radius, complete all as specified and directed

S&F 100mm dia bore cast iron branch pices fixed with cement joint complete all as specified and directed

S&F cast iron floor trap of 75 mm dia, chromium plated grating including jointing to waste pipe with lead joints and fixed in cement concrete 1:2:4, type B0 (using 12.50 mm graded stone aggregate) complete all as specified and directed.

S&F 100mm bore Cast iron P or S trap, complete all as specified and directed

S&F in repairs 15mm dia gun metal gate valve, with iron wheel head, screwed both ends for iron pipes complete all as specified and directed.

S&F in repairs 20mm dia gun metal gate valve, with iron wheel head, screwed both ends for iron pipes complete all as specified and directed.

S&F 15mm dia gun metal gate valve, with iron wheel head, screwed both ends for iron pipes complete all as specified and directed.

S&F 20mm dia gun metal gate valve, with iron wheel head, screwed both ends for iron pipes complete all as specified and directed.

M&L Preparation of old steel painted surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint to give an even and smooth surface having no sign of brush marks complete all as specified and directed.

M&L Preparation of old painted surfaces of wood and wood based material of any description over 10cm width or girth and applying one coat of synthetic enamel paint to give an even and smooth surface having no sign of brush marks complete all as specified and directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

Supply & Fixing of Armstrong Mineral Fibre Acoustical Suspended Ceiling system with DUNE(MICRO LOCK) EDGE TILES WITH ARMSTRONG XL 15mm EXPOSED STEEL ANGLE. The tiles should have humidity Resistance (RH) of 99%, NRC upto 0.5, Light reflectance >85%, Thermal conductivity k=0.052 - 0.057 w/m K, Colour White, Fire performance Class 0/Class1 (BS 476 part 6&7) in module size of 600X600X16 mm with Bio Block coating on the face of tiles, suitable for green building application, with recycled content of 38-41%. The steel angle should be of 'Armstrong' make with 15mm wide T-section flanges colour white having rotary stitching on all T-sections i.e the Main Runner, 1200mm & 600mm Cross section tees with a web height of 32, 27 & 27mm and a load carrying capacity of 7.5Kgs/sqm. The T-sections have a Galvanizing of 90gms per Sqm & passed through 500hrs of salt test, perimeter trim to be Armstrong wall angles of Size 30X19X19 mm , secured to walls at 450mm maximum centre to centre complete all as specified and directed according to manufacturers instruction.

Material and labour, shortcrete to existing RCC Chajja, facia, parapet, beams, landings and similar RCC members after removing all loose concrete & preparations of surface, application of derusting chemical such as Dr Fixit Rust Remover or equivalent, welding additional bars/welded steel wire fabric if found necessary, priming reinforcement bars with a coat of zinc primer of coating not less than 40 micron, provision of bonding agent with bonding material like Dr Fixit bonding agent and repair to external RCC structure with slurry light and steel/ply form work and shortcrete concrete of mixed 1:3:1 (one part of cement, three part of coarse sand and one part of 10mm and down aggregate) of minimum 50mm thick incl plastering 5 mm thick in CM mortar 1:3 all as specified in IS 9012-1978 (all priming and bonding epoxy based paint shall be of Dr Fixit epoxy zinc primer or equivalent) etc complete all as specified and directed, as below:- Note(s) : 1. The rates include for necessary formwork and scafolding etc. 2. Reinforcement and welded steel wire fabric will be measured and paid separately. Upto the height of 2 th storey bldg .

Mild steel TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending etc., and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Supply only welded steel wire fabric, weight not exc 4kg/sqm, complete all as specified and directed.

M&L for grouting using polymer modified waterproof grout. The detail procedure of inject grouting is as under complete all as specified and directed:- (i) Drilling of 12mm dia holes upto 40mm depth and provide PVC nozzles/entry ports over grid@ 1m c/c or less depending upon situation. (ii)Before injecting the grout compressed air to be blown to remove all dust and dirt. (iii) Grouting at pressure of 5 Kg/Sqcm to be done till refusal/rejection or apperance of grout from adjacent nozzle. (iv) Observe the cracks and make v groove along. (v) Nozzles and V groove shall be filled with polymer based mortar.

Demolition by using hand held electric drills, cutting machine, chisels etc (direct use of hammers on RCC roof for demolition is strcitly prohibited) of roof treatment including padding concrete of any description including mud in roof any thickness with and including roughening old concrete surfaces by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed.

M&L for cement concrete type B0 (1:2:4) (using 12.5 mm graded stone aggregate) as in padding and coping,incl hunching, benching etc complete all as specified and directed.

M&L for 10 mm thick in CM(1:3) rendering on fair faces concrete surfaces / roof top mixed with liquid water proofing compound finished even & smooth without using extra cement complete all as specified and directed. Note : Liquid WPC shall be measured and paid separately.

Supply only liquid water proofing compound complete all as specified and directed.

M&L roof kerb of cement concrete 1:2:4 type B0 mixed with and including SBR ploymer as manufacturer's instructions all around periphery of the wall complete all specified and directed.

M&L preparation of newly plastered surfaces of roof including cleaning the surfaces by using wire brush / pressure hose and applying high performance polyurethene liquid membrane waterproofing coating cold applied in two coats @ 1.5Kg /Sqm/ 2 coats spray/ brush applied, with an elongation of 300% to 700% and tensile strength of not less than 3 N/Sqmm as per ASTM D412 and ASTM D2370, crack bridging abiltity of 3.5mm as per ASTM C1305, shore a hardness of not less than 60 as per ASTM D2240. The item includes applying epoxy primer @ 0.15Kg/Sqm and a geotextile of 40 GSM to be applied over first coat while first coat is still wet,complete as per manufacturer's instructions complete all as specified and directed. Note: The contractor shall submit a gurantee of 10 years from the date of completion of work for waterproofing treatment alongwith manufacturer's gurantee. The amount of Rs. 40 ( Forty ) per Sqm and min of Rs. 4000/- for waterproofing treatment shall be withheld from contractor's final bill till the expiry of gurantee period. The contractor at his own option may furnish fix deposit receipt pledged in favour of GE(I) Kanpur against guarantee money. 2. The water proofing shall be carried out by authorised applicator of manufacturer. The name of applicator shall be got approved from GE before commencement of work.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting, bell, bell push etc and making good disturbed surfaces of walls, floor to match with existing specification complete all as specified and directed.

M&L for point wiring for one light point/fan/bell point/ exhaust controlled by one switch with 1.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable FRLS with proper colour coding and 1.5 sqmm PVC insulated unsheathed copper conductor single core multistranded cable (green colour) as earth lead in and including concealed non metalic rigid PVC conduit medium grade size 25mm dia with all fittings (ISI Marked) controlled by one switch including pressed steel terminal modular boxes of appropriate size and top cover with suitable size of modular plate with all accessories including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified and directed.

All as per item No 109.00 above but for one 3 pin 15 Amps socket outlet independent with 2.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 2.5 sqmm PVC insulated unsheathed copper conductor single core cable (green colour) as earth lead in and including pressed steel terminal modular boxes of appropriate size and top cover with suitable size of modular plate with all accessories complete all as specified and directed.

All as per item No 109.00 above but for one socket outlet 5 amps on indipendent board including pressed steel terminal modular boxes of appropriate size and top cover with suitable size of modular plate with all accessories complete all as specified and directed.

All as per item No 109.00 above but for one socket outlet 5 amps on same board including pressed steel terminal modular boxes of appropriate size and top cover with suitable size of modular plate with all accessories complete all as specified and directed.

M&L for switch modular type single pole one way 1 module 6 amps 240 volts complete all as specified and directed.

S&F switch modular type one way 1 module 16 amps 230 Volts complete all as specified and directed.

M&L for socket 6 amps modular type 2/3 pin combined 2 module, 230 volts complete all as specified and directed.

M&L for socket modular type , 2/3 pin, 6 and 16 amps combined 2 module, 230 volts complete all as specified and directed.

M&L for bell push modular type 1 Module one way 6 amps 240 volts complete all as specified and directed.

M&L for bell electric heahy duty Ding Dong type 230 volts single pole complete all as specified and directed.

M&L for ceiling rose surface bakelite 3 terminals complete all as specified and directed.

S&F Lamp holder insulated body with back plate for dome batten fittings complete all as specified and directed.

S&F of LED Aluminium batten luminaire surface mounted 4 feet system wattage of 20/22 Watts with lifetime of not less than 50000 burning hours with 70% of its initial lumen maintained.CRI>80, Power Factor>.95, THD<20%, Surge protection 3 KV in CM, IP-20n Protected, meets LED IS Specifications, Class-1, short circuit and over circuit protection voltage range-150 to 270 AC,system efficiency at luminaire level > 100lumen/watt and ibncluding connecting up with pvc sheathed 1.5 sq mm 3 core copper conductor flexible wire from ceiling rose to fitting fix complete all as specified and directed. Note:- All the above mentioned specifications will be verified through LM 79 and LM 80 report of NABL accredited lab before supply of LED fixtures.

S&F LED wall security light 20/25 W pressure die cast aluminium IP-66 road way luminaries with high power LED as light source having efficacy 120 lm/W complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, in extruded aluminium housing 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexiblecopper conductor cable of suitable size complete all as specified & directed.

S&F PDC Housing LED Bulkhead 10 watt luminaire with oval diffuser, equipped with 2kV in- built surge protection with IP 65 protection rating complete all as specified & directed.

S&F VTPN distribution board iron clad, double door with IP-43 1K-09 protection suitable for MCCB as incommer and MCB as outgoing 415 Volts 3 phase 50 C/s 4 way with appropriate size copper bus bar and neutral link, complete with one MCCB 4 pole 415 Volts 125Amps rating with rupturing cap 16 KA of the same make as of VTPN distribution board & with MCBs of required size making connection with thimbles & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site complete all as specified and directed.

Supply and fix sheet metal enclosure MCB distribution board, 8 way double door with IP-43 protection with 200 Amp rated bus bar complete all as specified & directed.

S&F amp rating 240 V, 10 KA 'C' curve miniature circuit breaker (MCB) 5 to 32 Amp in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

All as per item No 127.00 above but SPN 40 to 63 Amp complete all as specified and directed.

M&L in replacement for submain wiring with two single core PVC insulated flexible copper conductor multistranded cable (FRLS) of size 4 Sqmm with proper color coding and one single core PVC insulated flexible copper conductor multistranded cable green colour of size 4 Sqmm as earth lead in & including concealed PVC conduit medium grade 32mm dia cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed.

All as per item No 129.00 above but of 6 sqmm complete all as specified and directed.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver with cavity complete all as specified and directed.

M&L for Earthing with galvanised iron earth plate electrode of size 600x600x6mm thick as earth electrode with top edge of the earth plate not less than 1.5mtr below ground level using GI wire 4mm dia as earth continuity conductor connected to earth plate by means of GI thimbles nuts bolts washers all as directed including providing earth wire protection pipe GI light grade15mm dia from earth plate to main switch board/panel, watering pipe 20mm dia with wire mesh and funnel at top, earth pit and RCC pit cover in PCC 1:3:6 adequate quantity of charcoal dust and salt all around the erth plate, earth work in any type of soil remaing surplus excavated material all as required at site and specified in EP No 5 of SSR part I 1991 or directed by Engineer-in-charge and testing on completion.

Disconnecting & taking down upto 1200/1400m sweep ceiling fan and deposited to MES store yard and Supply, Installation, Testing and Commissioning of 1200 mm sweep, 5 star rated,Brushless direct current motor (BLDC) ceiling fan(Without Remote) class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.00, Air delivery minimum 210 CMM, 350 RPM (tolerance as per IS : 3742019) and all remaining accessories including safety pin, nut bolts, washers, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete all as specified and directed.

S&F in repair electronic fan regulator, socket size, step type suitable for ceiling fan of 1200 / 1400 mm sweep complete all as specified and directed.

S&F surface mounted rimless square downlight 24 watt moulded in engineering plastic complete all as specified and directed.

Supply and fixing in replacement luminaire diffused recess mounted 2' X2 ' warm white deep drawn CRCA housing with efficacy of 100 lm/W CRI> 90 provides uniform illuminatione 2 soft glare free light with driver, holders suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified & directed.

Disconnecting, dismantling and taking down CI/GI/DI/Cemented pipe line of size 200 mm bore, including all fittings with spigot and socket/ flanged end or any type, lead joint including removing from site complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth and getting out for taking out/laying pipes in soft/loose soil complete all as specified and directed.

Returning, filling,including spreading levelling watering and well ramming in layers not exceeding 25cm thick in solf/loose soil after pipes are laid and tested complete all as specified and directed .

Removing of excavated material not exc 50 mtr distance and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

Supply & lay pipe ductile Iron, S/S including specials , "Class k-9" , 200 MM (8") dia complete all as specified and directed.

Supply & lay pipe galvanized, ''Medium class'' including fittings 50 mm (2'') dia complete all as specified and directed.

Supply & lay pipe galvanized, ''Medium class'' including fittings 25 mm (1'') dia complete all as specified and directed.

S&F gun metal gate valve 50 mm dia with iron wheel head, screwed both ends for iron pipe, ISI marked including dismantling the old unserviceable existing valve complete all as specified and directed.

M&L for construction of valve pit chamber in replacement 600 x 600 x 950 mm internal dimensions, 6 mm thick MS sheet cover with 2 Nos MS hinges welded to angle iron frame of 40x40x6 mm thick with lifting hook and locking arrangement complete with necessary earth work, brick work in CM (1:6), 230 mm thick, PCC bed (1:4:8) type D2 150 mm thick, cement plastering, finishing 15 mm thick in CM (1:4) and applying a coat of black bituminous paint to the steel surfaces incl dismantling and removal of old unserviceble valve pit remains complete all as specified and directed.

Disconnecting electrically and taking out old unserviceable LT UG cables any type of size up to 95 Sqmm 3.5 core complete all as specified and directed.

Supply and laying in trenches or fixing to wall/pole or passing through pipe PVC insulated heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 95 Sqmm 3.5 core complete all as specified and directed.

M&L for sand cushning to U/G cable in layers of 23cm thick (8 Cm before laying the cable and 15Cm thick after laying the cable) in trenches including watering and consolidation, complete all as specified and directed.

Supplying and laid flat sub class 'B' bricks, old size, laid dry in trenches for the protection of U/G cable, complete all as specified and directed.

Supply,installing, testing and commissioning outdoor type LT Panel double door type (Safety Centre) of suitable size, padestal mounted, CPRI approved factory made totally enclosed, dust and vermin proof, double, front side openable, type IP-54 protection made of CRCA sheet 3.15 mm thick of outer panel and 2.00 mm thick inner compartment of panel size as per IS and having proper locking arrangement in front side door suitable for 440 volts, 50 Hz, 3 phase 4 wire system including cable glands of suitable size for incoming and outgoing cables and comprising with and including following accessories and mounted on PCC Plat form min 45 cm from ground level and PCC 1:3:6, 100 mm thick, 0.5 m all round the panel board including disconnecting cable from old unsv LT feeder piller box with MCCB, MCB, main switch, busbar and dismantling the same complete with the following items housed in :- BUSBAR :- 400 Amps rated copper bus bar TPN duly insulated with coloured PVC sleeve as per standard colour code and rigidly mounted on bakelite / DMC insulator bus bar support (Square / round) insulators of suitable size and good insulation resistance (Busbar to MCCB shall be connected through suitable size of copper busbar). INCOMING:- (i) 4 pole MCCB of capacity 250 Amps, 415 Volts, 50 Hz, 3 phase breaking capacity 36 KA with adjustable thermal& adjustable magnetic - 01 No. (ii) Digital multifunctinal meter V, A, F, kW, KVA, kWh, kVAh, kVArh, THD, Neutral current, Max Demand (with RTC),- 01 No. (iii) Indicator lamp with integral circuit (230/240 volt) and cluster LED (RED, ORANGE, BLUE) -01 set (iv) CT (400/5A) -03 Nos OUTGOING:- (a) 4 pole MCCB of capacity 100 Amp, breaking capacity 25 KA with adjustable thermal & adjustable magnetic - 03 Nos (b) MCCB 4 pole of capacity 63 Amp breaking capacity 25 KA with thermal magnetic release, adjustable type with rotary handle - 01 Nos (NOTE: Rate quoted shall be deemed to be inclusive of replacement of all cable lugs, by removing damaged part of cable and taking out cable from loop to required length including necessary earth work as per site requirement or as directed by Engr-in-charge). Factory inspection at manufacturer premises shall be carried out by the Engineer in charge or rep of GE I kanpur as detailed by GE before despatch of panel.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core complete all as specified and directed.

JOG CONSTRUCTION (BID ID -3474079)

murty construction company (BID ID -3474358)

Khalil Ahmed and Sons (BID ID -3479463)