SPECIAL REPAIR TO BLDG NO. P-06 AND CERTAIN LBW AND MW WORK UNDER ZONE-II AREA AT JAIPUR MIL STN.

Amount

Demolition of PCC in floors (other than ground floors), beams staircases, landing, chajjas, and similar suspended work, including removing out of MD Land

Demolition of cement concrete in ground floors and pavings not exc 15cm thickness (below or above ground level), including removing out of MD Land

Excavation in trenches n.exc 1.5m wide & n.exc 1.50m in depth for foundation , etc or for shafts, wells, cess pits, man holes,pierholes etc n. exc 10 sqm on plan & getting out in soft/loose soil.

M&L PCC 1:4:8 Type D2 (40 mm graded aggragate) as in foundation, filling and mass concrete.

Taking down cement plaster on brick / stone wall, ceiling etc incl. raking outs joints hacking for key scrubbing with water

M&L rendering 15mm thick on stone masonry surfaces in CM 1:4 finished even and smooth without using extra cement

M&L rendering 15mm thick on stone masonry surfaces in CM 1:6 finished even and smooth without using extra cement

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Removing excavated material exc. 250m but n exc. 500 m and depositing where directed

Dismantling water tanks,exc 500 and n.exc 1000 litr

Dismantling water tanks,exc 250 and n.exc 500 litr

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I - Capacity 1000Litre

M & L for TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality confirming to IS 432

All as per Item No.13 above but for 6mm dia and over upto and incl 8mm dia

Ditto but for 5mm dia and over upto and incl 10mm dia in stirrups, spacers and binders.

Taking up or down steel tubing and connection, including cleaning 15 mm bore

Taking up or down steel tubing and connection, including cleaning 20 mm bore

S&F GI tubing medium grade with all fitting 15 mm bore fixed to wall or concealed or fitted to ceiling or laid under floor

S&F GI tubing medium grade with all fitting 20 mm bore fixed to wall or concealed or fitted to ceiling or laid under floor

S&F CP Stop valves fancy type, cast copper alloy screwed down high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions in 15 mm bore fixed in repairs.

S&F Stop valves cast copper alloy screwed down high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions in 20 mm bore fixed in repairs.

S&F CP Bib taps, cast copper alloy with capastan heads ,screwed down, screwed for iron pipe or for brass ferrule and fixed in repair 15 mm

S&F in repair CP stop valves, cast copper alloy screwed down high presure, with Capastan head, screwed both ends fancy type chromium plated with long shank and cup (concealed type), 15 mm

M&L PVC syphonic action type flushing cistern of required capacity, low level white with inlet ball valve float and handle including brackets

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

Cutting into existing manholes for connecting new drains 150mm dia, making good to pipe & rendering, cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, & reforming benching as required

M&L Concrete bed to 150mm dia drain pipes including packing under, & haunching against the sides of pipes after they are laid & tested; in PCC (1:4:8)

Slat-glazed stoneware drain pipes laid in trenches and jointed as specfified dia of pipe 150 mm

M&L PCC in surface channels and drains type B1 (1:2:4) using 20 mm graded stone aggregate

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms, moulds mitred/stopped ends etc.

Add or deduct for each 25 mm girth or part thereof over or under 30 cm to serial item no 30 Note :- This item is for adjustment of rate only

M&L 16-18 mm thick Granite stone (table rubbed & polished) in steps, shelves, jambs & window cills/kitchen platform incl bedded & jointed with grey cement slurry & pointing in white cement using marble dust with admixture of pigment to match with marble shade of Granite stone & incl grinding & polishing the exposed edges over and incl 15mm thick screed bed in CM 1:4.

Demolition of brickwork or stone/boulder masonry, built in lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles

S&F two way Bib taps fancy type cromium plated long body cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule,long body,15 mm make cera or equivalent as approved by GE

S&F Jet Suitable for EWC with 01 meter pipe

Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured)

Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface

Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area

Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall

M&L RCC M-25 (Design mix) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete

M&L RCC M-25 (Design mix) as in Beams, cantilevers, bressummers, lintels over 1.5m span.

All as per item No 40 above but as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like.

M&L RCC, M-25 (Design mix) as in columns

Ditto as per item No 40 above but as in Chajjas.

M & L Brickwork old size brick with fly ash bricks, traight or curved on plan exc 6m mean radius, built in CM 1:4

M & L for Brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4.

M&L formwork to sides of concrete foundations footings bases of columns etc rough finished surfaces of concrete flat

All as per item no 47 above but for sides of pillars columns etc

M & L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick finished with rough finish flat surfaces.

M&L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelvves including sup-ports, overhangs, etc. also splays between floors and beams, etc finish with rough finish flat surface.

M&L form work to chullah hoods, chajjas, troughs and similar items including edges finish with rough finish flat surface.

M&L formwork to edges of concrete flats, treads, breaks in floors, window cills, cocnrete railings, opening in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide.

Screed bed or bedding layer or mortar 15mm thick in cement mortar 1:6

M&L for 100 mm thick PCC (1:4:8) type D-2 as in sub base of floor.

Non Skid joint free coloured ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

Ditto as per item No 55 above but for work on vertical surface such as skirtings, dados and risers to steps etc.

M&L Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set over and incl 15mm thick screed in CM 1:6 and jointed in neat cement slurry and pointed in white or coloured cement to match

Non Skid joint free coloured ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

M&L Machine cut kota stone slab as in shelves / flooring 20-25mm thick over and incl cement screed base 15 mm thick in 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over and incl 15 mm cement plaster in 1:6 jointed with ditto

M&L for Glazed ceramic coloured tiles ( 450 x 300 mm) x 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps ,wall etc set over 10 mm thick cement plaster in CM 1:4 and jointed in neat cement slurry and pointed in white or coloured cement to match

M&L for Vetrified Ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match. Light shade over and incl 15 mm thk screed bed in CM 1:6

All as per Item No. 63 above but in skirting of size 600 mmx100 mm in vertical surfaces

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:4) even and smooth without using extra cement.

M&L rendering 15mm thick on other than fair faces of brick work or stone masonry surfaces in CM 1:6 finished even and smooth without using extra cement

M&L rendering 5mm thick plaster on ceiling surfaces in CM (1:3) including finish even and smooth with out using extra cement

M&L rendering 10mm thick plaster on ceiling/ RCC faciasetc surfaces in CM (1:3) including finish even and smooth with out using extra cement

M&L for preparation of new plaster surface and apply two coat of weather proof paint over a coat of primer including over one coat of external putty complete as directed

M&L for preparation of new plaster surface and apply two coat of Oil bound distemper on wall surface over one coat of primer including one coat of putty

M&L for preparation of new plaster surface and apply two coat of Oil bound distemper on ceiling surface over one coat of putty

M&L preparation of new plastered wall surfaces and applying two coats of oil bound distemper over a coat of putty over one coat of primer on walls

Taking down cement plaster on roof surface including existing roof treatment complete all as directed.

M&L 75 mm of thick PCC (1:3:6) type C-2 as in plinth protection

M&L plain cement concrete type C-1 1:3:6 (using 20mm graded stone aggregates) as in plinth protections 50 mm thick finished even and smooth without using extra cement

M&L PCC 1:3:6 type C2 using 40 mm graded stone aggregate in foundations, filling and mass concrete

M&L for Screed bed or bedding layer or mortar 15mm thick in cement mortar 1:4 with WPC on roof surfaces

M&L water proofing treatment to roof surface by applying with a coat of cold aplied bituminous primer @ 0.40 ltr/Sqm conforming to IS-33894 and laying APP based polymeric membrane not less than 3mm thick, weighing not less than 3.5kg/sqm, reinforced with polyester non woven fabric (weighing not less than 150gms/sqm) shall only be used. It shall be laid by torch application. Side over laps shall be 75mm and the end lap shall be 100mm and all over laps and joints shall be sealed by torch application. For parapets, membrane shall be taken to a height of minimum 60cm and then inserted inside the parapet groove. This shall be finished by a membrane flashing including a coat aluminuium paint over APP membrane as per manufacturer instructions.

Supply only integral waterproofing compound as approved

Rounding to edges of stone slabs one edges such as in steps, cooking platform and other similar situations

Extra over rendring or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work exc 15cm but n exc 30cm in width or girth; including cutting to edges, all mitres and stopped ends, etc

S&F in repair CP Angle valve cast copper alloy screwed down high pressure with capastan head, screwed both ends for iron pipe or for unions in 15 mm bore fixed.

S&F CP angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe for 15mm bore pipe .

S&F Pillar taps fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and in repair fixed 15 mm bore

S&F in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15mm

S&F Bib taps fancy type cromium plated long body cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule,long body,15 mm bore.

S&F cromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union ,125mm size

S&F wash down water closet (Pedestal pattern) complete with flushing cistern and seat cover complete all as appoved and directed.

S&F in repair wash down water closet (Pedestal pattern) complete all as appoved and directed.

M&L plastic water closet seat,black,closed patteren with flat bottom, and cover and mild sttel chromium plated or aluminium hinging device

S&F in repair Vitreous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern ), fixed all as specified.

S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm but including brackets complete all as appoved and directed.

S&F tubular towel rail 20mm dia, D type, 60cm long between flanges,brass CP

S&F in repair tubular towel rail 20mm dia, D type, 60cm long between flanges,brass CP

S&F PVC connections 15mm size with PTMT nuts of length 450 mm

S&F PVC (SWR) multi floor trap with grating including jointing with solvent cement

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors dia of pipe 110 mm

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors dia of pipe 75 mm

PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls dia of pipe 110 mm

S&F 110 mm dia PVC (SWR) bends any radius

S&F 75mm dia PVC (SWR) bends any radius

S&F PVC (SWR), junction single, (Single T) equal or unequal with oval access door dia of pipe 75 mm

S&F PVC (SWR), junction single, (Single T) equal or unequal with oval access door dia of pipe 110 mm

S&F PVC (SWR) vent cowl 110 mm dia

M&L for Salt-glazed stoneware gully traps, square or round mouthed, type `P' size 150mmx150 mm complete all as appoved and directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I Cap 500 Liter complete all as appoved and directed.

S&F ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed dia of pipe 20mm

S&F in repair ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed dia of pipe 20mm

S&F waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed dia of pipe 32 mm

S&F PVC waste pipe 25 mm dia 75 cm long with 32 mm dia connector for WHB

S&F grating doom 100 mm dia made of stainless steel.

S&F grating doom 125 mm made of stainless steel dia with waste hole .

S&F PVC Grating doom 100 mm dia

S&F PVC Grating doom 125 mm dia with waste hole

Sheet Glass shelf assembly consisting of 5.5 mm thick shhet glass shelf 12 cm wide with chromium plated bracket guard and raling 60 cm long

S&F liquid soap container fixed with and including Chromium plated brass screws and wooden/platic cleats .

S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing

S&F Steel window with side hung shutters Factory made including box type hinges with steel handle and steel peg stay complete with glazing bars devetailed or welded.

S&F Steel window with side hung shutters Factory made including box type hinges with steel handle and steel peg stay complete without glazing bars devetailed or welded

M&L for Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290(Gde E-165)

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 290 (Gde E-165)

M&L 35mm thick factory made plain, framed, paneled door shutters kiln seasoned and chemically pressure treated second class, hardwood (two panels) with lock rail and panel of 9mm thick BWP commercial marine grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive confirming to IS-710. The size of rails and style shall be as per IS-1003. The shutter shall be fitted to chowkhats as directed.

S&F 35mm thick factory made second class hardwood glazed and skelton door shutter kiln seasoned and chemically treated, open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete. The size of members of shutters shall be as specified in MES SSR Part-I. The shutter shall be fitted to chowkhats as directed.

M&L 18 mm thick MDF Board one side white and one side decorative lamintion using in cupboard shutter including tape etc complete fixed as per standard trade practise .

M&L 12 mm thick MDF Board both side choice lamination fixed in aluminium doors/partition

Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples

Sheet glass ordinary quality and glazingwith oil puttyin square n.exc 0.50 sqm in each pane in 3 mm thickness

Preparing new wooden surfaces of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer

M&L preparing new steel surfaces and applying two coats of synthetic enamel paint over one coat of redoxide primer area exc 10 cm width or girth

M&L preparing new steel surfaces and applying two coats of synthetic enamel paint over two coat of redoxide primer area exc 10 cm width or girth

S&F butt hinges extruded brass with galvanised mild steel hinge pin, anodised and fixed size 125 mm

S&F Butt hinges, medium weight, cold rolled mild steel, and fixed 100 mm

S&F Butt hinges, medium weight, cold rolled mild steel, and fixed 75 mm

S&F Mild steel pressed handles, oval type,stove enamelled black 150mm

S&F Mild steel pressed handles, oval type,stove enamelled black 125mm

S&F Extruded aluminium alloy handles, fabricated type., anodised size of handle 150 mm

S&F Extruded aluminium alloy handles, fabricated type., anodised size of handle 100 mm

S&f 150 mm long stain less steel handles of superior quality for cup boards .

S&F mortice lock, vertical type, size 65mm brass 2 lever

S&F mortice lock, vertical type, size 100mm brass 4 lever

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed 250mm

S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed Length of bolt 150 mm

S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed Length of bolt 100 mm

S & F MS barrel tower bolts of stove enamelled black with bright bolt and fixed 100mm.

S & F MS barrel tower bolts of stove enamelled black with bright bolt and fixed 150mm.

S&F floor door stopper of aluminium alloy body with single rubber shoe

M&L Aluminium powder coated Drapory rod 25 mm dia with two Nos brackets and 02 Nos decorative finial with each door/window.

M&L Precast RCC cover 300 mmx300 mm with frame

M&L Precast cement concrete in landing, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles as requred and directed.

M&L PCC 1:2:4 using 20mm graded stone aggregate in coping including necessary formwork.

M&L 30 mm thick PCC 1:2:4 using 20 mm graded stone agg in floor finished fair & even complete

M&L 75mm thick cement concrete type D-2, 1:4:8 all as directed.

M&L 25mm thick sand layer

M&L Machine pressed precast concrete interlocking paver block,coloured rubber moulded PU coated any shape and size 60mm thickness, M-35 Grade complete all as directed.

Chequered cement concrete tiles 25cmx25cmx25mm thick, set,jointed and pointed in neat cement slurry in floors.with grey cement and no pigment over and incl 15 mm screed in 1:6

S&F in repair Vitreous China urinals, bowl type (back or corner wall type), of size 465 x 355 x265 mm of white colour complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipee. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

S&F in repair PVC (SWC) floor trap, with grating including jointing with solvent cement fixed in repair 75 mm bore

S&F in repair PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in trenches or in floors dia of pipe 100 mm fixed in repair

S&F in repair PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in trenches or in floors dia of pipe 75 mm fixed in repair

S&F in repair PVC (SWR) pipes single socketed in any length with rubber ring joints ficxed to walls dia of pipe 100 mm fixed in repair

S&F in repair PVC Bends 100/110mm bore, with oval access doors

S&F in repair PVC Bends 75 mm bore, with oval access doors

Taking down chowkats or frames with shutters not exc 1.50 Sqm each (without taking off shutters from the frames).

Taking down chowkats or frames with shutters exc 1.50 Sqm each but not exc 4.00 sqm each (without taking off shutters from the frames).

S&F powder coating anodised aluminium work for doors, windows, ventilators,grills with one or more rebates including joining cleat for fixing etc. complete all as specified.

Taking down existing loose lime concrete//Lime mortar from Stone Chajja (Ht approx 3.00 m) and repairing the same by providing cement concrete average thickness 25 mm to match with existing Chajjas all including necessary Scaffolding

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc.laid dry.

M&L Pre-cast cement concrete block masonry with solid bloacks, exc.10 cm in width and setting in mortar, complete

M&L preparing new concrete surfaces and applying two coats of synthetic emnamel paint over one coat of primer

M&L for Dholpur stone cladding 16 mm to 18 mm thick gang saw cut with machine cut edges,uniform colour of each stone size not exceeding 0.25 Sqm fixed with and including ,making V groove at top and bottom of stone and drilling hole for hold fastner,polishing,rubbing and including silicon treatment

S&F for hydraulic operated double action floor spring for aluminium door made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

M&L 5.0 mm thick plain glass packing with rubber gasket, Al beading etc around both sides for fixing of glass all as specified and directed.

M&L Drapory rod 19 mm dia with two Nos brackets in each door / windows etc

S&F modular switch one way 6 amp 1 module all as per Legrand Mylinc cat ref No 675501 or equivalent in Schneider Zencelo or Crabtree Murano s approved.

S&F modular switch one way 16 amp 1 module all as per Legrand Mylinc cat ref No 675511 or equivalent in Schneider Zencelo or Crabtree Murano as approved.

S&F modular socket 6/16 amp - 2/3 pin combined 2 module all as per Legrand Mylinc cat ref No 675555 or equivalent in Schnieder Zencelo or Crabtree Murano as approved

S&F modular socket 6 amp - 2/3 pin combined 2 module all as per Legrand Mylinc cat ref No 675550 or equivalent in Schnieder Zencelo or Crabtree Murano as approved

S&F modular hum free electronic step fan regulator 100 watt 2 module all as per Legrand Mylinc cat ref No 675530 or equivalent in Schnieder Zencelo or Crabtree Murano as approved

S&F ceiling rose 3 plates polycarbonate body complete. Make : Anchor Penta PC/Havells Reo/SSK as approved.

M & L Brick work with sub class 'B' brick (old size brick) straight or curved on plan exc 6m mean radius, built in CM 1:6

M&L 40mm thick PCC (1:2:4) type B1 using 20 mm graded stone agg as in floor etc finished even and smooth without using extra cement complete all as directed.

M&L PCC (1:2:4) type B1 using 20 mm graded stone agg as lintels upto 1.5m clear span & coping, cills, kerbs etc including form work complete all as directed.

S&F Mild steel as in Hold fast, hook, pintol, hinges or similar work confirming to Fe290 complete all as directed.

S&F Expanded metal, cut to length, bent to shape required and typing with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed to wood or steel members weight per square metre not exc.4 kg complete all as directed.

S&F Thickness of sheet 1.25 mm Mild steel, plain, black sheet in hearths ; covering to door shutters; covering to door chowkets ( frames ) ; chullah hood ; water tanks ;water troughs ; ducts; urinal troughs and funnels, etc. cut to size, edges beaded if directed, holes punched ; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required Thickness of sheet 1.25 mm

M&L rendering 15mm thick on fair faces of brick surfaces in CM 1:4 finished even and smooth without using extra cement

M&L for preparation of new plaster surface and apply two coat of cement base paint on wall complete as directed

Surface excavation n.exc 30cm deep and averaging 15 cm and getting out in hard dense soil all as specified and directed.

M&L machine pressed rubber moulded precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, with grey cement and no pigment laid over and including 25mm thick sand cushion, duly joint filled with sand and compacted using mechanical ptale vibrator complete all as directed.

M&L providing pre cast rubber moulded kerb stone in cement concrete 1:2:4 type B1 using 20mm graded stone agg complete all as directed.

S&F 20 amp, single pole and neutral, socket outlet, with 2 pole and earth, metal enclosed plug top in power coated CRCA steel sheet enclosure recess mounted with chained metal cover for the socket outlet with and including one number single pole 'C' series MCB 16 amp as required. Make : Legrand cat ref No 607841 & 408592 or equivalent in Hager or Schneider as approved.

S&F MCB distribution board, powder coated, CRCA steel sheet, degree of protection IP 43, IK-09 with reversible double door, recess mounted , having insulated 100 Amps tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required with SPN, 240 volts, 12 ways. Make : Legrand Cat Ref No. 507612 or equivalent in Schneider or Hager as approved.

M&L for sub main wiring along with earth continuity conductor with, PVC insulated FRLS multistranded copper conductor cable (Phase-Red, Neutral-Black, Earth=Green) drawing into and including concealed rigid non metallic PVC conduit, medium grade, ISI marked ivory colour along with accessories 2x6.0 Sqmm + 1x6.0 Sqmm earth wire in 20mm dia conduit medium grade , ISI marked ivory colour along with accessories.

All as per Item No. 184 above but with accessories 2x6 Sqmm + 1x4 Sqmm earth wire in 25mm dia conduit.

All as per Item No. 184 above but with accessories 2x4 Sqmm + 1x2.5 Sqmm earth wire in 20mm dia conduit.

Supply and fixing ceiling fan 1200mm sweep 50 Hz AC 230 volts, 5 star rated in white colour with fan motor, blade set, 0.45 mtr down rod, canopy set, rubber reelincluding 0.5 Sqmm three core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling and wiring MES No on fan body as required. Make : Havells Model No ES-50 or equivalent in Oreient/CG/Standard.

S&F water heater 25 litre capacity BEE star rating 5 in approved colour, heating element 2.0 KW, adjustable temperature setting knob for temperature setting between 25° C to 75° C, outer tank made of non metallic engineering plastic, inner tank made of extra thick superior cold rolled steel provided with high density PUF insullation including 15mm bore 450mm long flexible PVC connection pile for cold water supply and 15mm bore 450mm long cromium plated metallic flexible pipe connection of hot water complete. complete. Make- Hevells Adonia or equivalent in Daspass or Recold or Bajaj as approved.

S&F in repairs LED batten 9 watt, 900 lumens operating voltage 160 to 360 volts, colour temperature 6500K including connection all as per Philips Astra Line 9-Watt LED batten or equivalent in Wipro or CG as approved.

S&F LED bulkhead fitting 9 watt IP 66 & IK 09 with pressure dis cast aluminium housing & polycarbonate body diffuser duly pre wired connection with 0.75 Sqmm PVC insulated & sheathed three core flexible multi stranded copper conductor cable all as per Philips cat ref No WT 202W LED 6S PSU S2 PC or equivalent in other specified make as approved.

S&F in repairs LED batten (1.2M) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minium system efficacy of 105 lumen per watt and total power consumption not more than 19 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete. Make : Philips cat ref No ENDURALED BATTEN "BN 108C LED 20S PSU CDL WH" or Bajaj cat ref No BLTRU 20W WH VIVA or equivalent on other specified make as approved.

S&F propeller type heavy duty exhaust fan with louvers 300mm sweep single phase 900RPM including cutting of hole in stonewall masonary and connection as required. Make : havells model Turbo Force SP or equivalent in Almond/CG/Bajaj as approved by GE.

Renewal of street light fittings like tube light/CFL/T5 of any description with Greenline high effieciency LED street light luminaire 25 watt complete with drive, pressure die cast aluminium housing, UV stablized polycarbonates cover, in-built power unit, IP 65 protection including mounting bracket made of 25mm GI pipe, medium grade ISI marked not lessthan 1.2m bend in shape with two number clamps, nuts, bolts, washers as required. Make - Philips cat ref No BRP022 LED 10 CW MR S1 PSU GR or equivalent in or Havells or C&S as approved.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken modular GI metal boxes not less than 1.0mm thick and white modular mounting cover plate with frame for mounting modular switches, sockets, fan, regulators etc as required for one light point controlled by one switch

All as per item No 194 but one fan point controlled by one switch.

All as per item No 194 but one socket outlet 6 amp controlled by one switch on independent board.

All as per item No 194 but one socket outlet 6 amp controlled by one switch on the same board with other switches.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken modular GI metal boxes not less than 1.0mm thick and white modular mounting plates with frame for mounting modular switches, sockets as required for 3 pin 16 amps socket outlet point controlled by one switch.

S&F MCBs of 'C' series single pole 6 to 32 Amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete. Make : Legrand Cat Ref No. 408587 to 408595 or equivalent in Schneider/Hager as approved. (Note for MCBs & MCB DBs :- MCCBs, MCBs & MCB DBs shall be of the same make.

All as per item No 199 but double pole 10 to 32 Amps. Make : Legrand Cat Ref No. 408631 to 408636 or equivalent in Schneider/Hager as approved by GE

M&L for pipe in pipe chemical earthing with GI pipe electrode 3.0 m long having outer pipe dia 50mm & inner pipe dia 25mm duly filled with highly conductive and anti corresive compound tested from NABL certified Laboratory of required quantity in ground by digging a bore of 100mm dia surrounded by soiul friendly backfill compound including connection with galvanised earth wire 4 mm dia from earth electrode to the equipment to be earthed duly protected in 15mm medium grade GI pipe upto 7.5m, making PCC pit of size 0.3m x 0.3m x 0.3m (inner size) in mix 1:3:6 type C1 with PCC 1:2:4 type B-1, 40mm thick cover with lifting hook made out of 8mm dia bar and testing on completion to achieve value not more than 2.0 ohm complete.

S&F TV Co-axial modular socket 1 module as per Legrand Mylinc cat ref No 675546 or equivalent in Schneider Zencelo or Crabtree Murano as approved.

S&F telephone socket double RJ11, 1 module as per Legrand Mylinc cat ref No 675544 or equivalent in Schneider Zencelo or Crabtree Murano as approved.

S&F power unit for AC or geyser 3.5 KW 4 module including sunken modular GI metal boxes not less than 1.2mm thick and white modular mounting plates with frame all as per Legrand Mylinc cat ref No 675558, 689009, 675564 & 675584 or equivalent in Schneider Zencelo or Carbtree Murano as approved.

S&F stop valve/Gate 25mm dia valve cast copper alloy screwed down high pressure with butterfly handle screwed both ends for iron pipe or for unit and fixed.

Supply and lay pipe galvanized , "medium class" including fittings 25mm (1.00") dia.

Drilling and tapping cast iron water mains (in position) for branch connection of 15/25/40/50 mm dia including clamps, nuts, bolts and rubber packing as required.

Supplying, laying or fixing or passing through pipe, testing and commissioning 1100 volts grade ISI marked XLPE insulated and PVC sheathed steel tape/wire armoured underground stranded aluminium conductor cable of 25 Sqmm 3.5 core. (Make : Havells/Polycab/Finolex/Universal as approved)

M&L sand filling in trenches with clean dry fine sand unwashed including gently punning around cables complete.

Supplying and laying old size bricks, common burnt clay building bricks sub class 'B' designation 75 laid in trenches over sand for cable protection complete.

Taking down carefully surface copper point wiring with PVC casing capping (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling rose, regulators, sockets, light fittings etc and making good disturbed surfaces complete

M&L for earthing with galvanized steel earth plate electrode 600mmx 600mmx6mm thick buried directly in ground (earth pit not less than 2.25 meter deep below normal ground level) with the top edge of the plate not less than 1.5m below normal ground level connected to galvanized earth lead wire 4mm dia by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate No. 03 of SSR Part -I connected to earthing point and including 15mm bore light grade G.I. protection pipe (upto 7.5 mtr from edge of the pit), PCC pit in mix 1:3:6 type C1 with PCC 1:2:4 type B-1, 40mm thick cover, watering arrangement with funnel and wire mesh and 20mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earh work completion.

S&F steel tubes ISI market light grade galvnised with all fitting fixed to wall/ poles/ laid in road crossing etc as required of size 40mm dia.

S&F modular switch two way 6 amp 1 module all as per Legrand Mylinc cat ref No 675502 or equivalent in Schneider Zencelo or Crabtree Murano s approved.

S&F modular bell push, 6 amp, 1 module all as per Legrand Mylinc cat ref No 675504 or equivalent in Schneider Zencelo or carbtree Murano as approved.

S&F door bell AC 240 volts, single pole complete. Make : Anchor Penta PC/Havells Reo/SSK as approved.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken modular GI metal boxes not less than 1.0 mm thick and white modular mounting cover plates with frame for mounting modular switches, sockets, fan regulators etc required for one light point controlled by one switch.

All as per item No 217 but one fan point controlled by one switch.

All as per item No 217 but one socket outlet 6 Amps controled by one switch on the same board with other switches.

All as per item No 217 but one socket outlet 6 Amps controlled by one switch on independent board.

All as per item No 217 but one bell point controlled by one bell push.

All as per item No 217 but one light point controlled by two, two way switches.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken modular GI metal boxes not less than 1.0 mm thick and white modular mounting cover plates with frame for mounting modular switches, sockets, fan regulators etc required for 3 pin 16 amps socket outlet point controlled by one switch.

Taking down industrial plug and socket including one number single pole MCB any make, any capacity after disconnecting complete.

Taking down MCB distribution board with incoming and outgoing controls any make, any capacity after disconnecting complete.

Taking down carefully submain wiring with PVC casing caping/PVC surface conduit and making good distrubed surfaces complete.

Schedule of Credit (tentative)

KARNI CONSTRUCTION COMPANY

M/S JALANDRA CONSTRUCTIONS

Smita Constructions

J.J.ENGINEERING

Sh Manoj Nagar