CERTAIN REPAIR TO DRAIN, PATH AND FENCING IN ZONE C UNDER AGE B/R-III AT BB CANTT, SRINAGAR

Amount

Fixing only mild steel as in Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., & Including dismantling of mild steel work of any description not otherwise provided including demolition of bed blocks/anchor PCC block, complete all as specified and directed. Note:- (i) Old mild steel obtained from dismantling shall be used. (ii) PCC for poles shall be measuerd and paid saparately under respective item.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F mild steel as in Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 & cleat to weld arth existing angle iron from bar, complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and Including dismantling of any sheet, any thickness and gauge, complete all as specified and directed.

M&L for Brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:6) and Including demolition of brickwork or stone masonary built in cement mortar or cement lime mortar including all quoins, arches,pillars etc, complete all as specifed and directed.

M&L for Precast cement concrete hollow block masonry type 1:3:6 using (16 mm graded crushed stone aggregate) exc. 10 cm in width and setting in mortar complete built in CM 1:6 and Including demolition of brickwork or stone masonary built in cement mortar or cement lime mortar including all quoins, arches, pillars etc, complete all as specifed and directed.

M&L for rendering 15mm thick on other than fair face of brick work in cm 1:4, surfaces to be finished even and smooth without using extra cement, with and including using water proofing compound @ 3% by weight of cement, complete all as specified and as directed.

M&L for cement concrete (1:2:4) type B-2 (using 40mm graded crushed stone aggregate) as in surface channel and drains, complete all as specified and directed.

M&L for Plain cement concrete (1:2:4) type B1, (using 20mm graded crushed stone aggregate) as in coping etc including weathering, slightly rounded or chamfered angle and throating, complete all as specified and directed.

M&L for providing pre-cast RCC (1:2:4) type B1 (using 20mm graded crushed stone aggregateet) as in landings, cover slab (for manhole etc) including necessary form work and Including demolition of RCC of any description and in any position complete all as speciofied and directed.

S&F framed work such as griils, grating, angle iron door frame etc, with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, frame for manhole cover ,barred iron doors, ladders, framed balusters, walk ways, railings frame work of water tanks and similar work conforming to Fe-290. Gde E-165, complete all as specified & as directed.

Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends,for manhole cover handle and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam,tee, angle, channel or flat sections) including distance pieces,cleats etc Fe 410-w(Gde-E-250)Quality-A, complete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed.

S&F for joist,channel,angle,or tee sections,fixed independently, without connecting plates,etc (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe-410 W(Gde- E-250) Quality-A, complete all as specified and directed.

M&L for Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, complete all as specified and directed

S&F 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with coach screws and washers, in roof, wall etc with grade of zinc coating 275 and Including dismantling of plain or corrugated steel sheeting any gauge,thickness including roof covering etc, complete all as specified and directed.

Demolition of cement concrete un-reinforced any description in any position, complete all as specified and directed.

M&L for Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour,design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paverblocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and dirceted.

M&L for 100 mm thick PCC (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of flooring/ hard standing, complete all as specified and directed.

Demolition of cement concrete un-reinforceed in ground floor and paving n.exc 15 cm thick below or above ground level, complete all as specified and directed.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paverblocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and dirceted.

M&L for Chequered cement concrete tiles 30cmx30cmx22-25mm thick, with white cement and pigments set, jointed in neat cement slurry in floors laid over and including 15mm thick screed bed in cement mortar (1:4), complete all as specified and directed.

M&L for 75mm thick PCC (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of flooring/ hard standing, complete all as specified and directed.

M&L for Preparation of new plastered surfaces of walls and applying two coat of cement base paint, complete all as specified and directed

M&L for PCC (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete, complete all as specified and directed

M&L for 2nd Class Soft wood Wrought, 35mm x 10mm laths (fixed straight or diagonally) in two way trellis work with 50mm spaces in the clear, including 75mm x 50 mm fillet (notched to take ends of laths) all round and fixed Including Dismantling of trellis Work (Jafri) two way including taking as under of battens in trellis (posts and rails measured separately), complete all as specified and directed.

M&L for preparation of new wooden Surfaces of any descri-ption, over 10cm in width or girth , not other wise described and appling two coats of synthetic enamel paint over a coat of priming with pink primer, complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut,exc 10cm and n exc 15cm long with dia of neck 5 to 10mm, complete all as specified and directed.

Dismantling posts or struts embedded in Concrete, brick work, masonry, etc. (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground, complete all as specified and directed.

Dismantling of fencing wire mesh, any type complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire, complete all as specified and directed

Supplied only chain link MS galvanisd fencing, any size or type complete all as specified and directed. Note :Actual weight of the fencing shall be ascertained by board of officers to be convened by GE.

S&F galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails staining bolts including, securing or tying at crossings with and provn of galvinised mild steel wire, staples or steel pins etc as directed (each line wire to be measured), complete all as specified and directed

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long with dia of neck 5 to 10mm, complete all as specified and directed.

Notes :- An amount of Rs. 1,68,480.00 on account of Credit Schedule for Schedule 'A' Part-II shall be deducted from total quoted amount of BOQ to arrive at the contract sum.

M/S Paradise Constructions (BID ID -3301947)

M/S AIJAZ ENTERPRISES (BID ID -3300791)

M/S Tajamul Ah Buchh (BID ID -3302260)

M/S Vivek Gupta and Co (BID ID -3301650)

M/S Himalayan Construction and Co. (BID ID -3301883)

GHULAM NABI GILKAR AND CO (BID ID -3300487)

Javeed Builders (BID ID -3302026)