PROVN OF 200 KVA TRANSFORMER, 200 KVA VOLTAGE STABILIZER WITH ACCESSORIES/ ALLIED INFRA, SPL REPAIR TO LIGHTENING CONDUCTOR, EARTHING AND OTHER ALLIED WORKS AND MAIN PIPE LINE WITH ALLIED INFRA AT VARIOUS LOCATIONS IN THE AOR OF AGE E/M UNDER GE 969

Supply, Installation, commissioning and testing Servo voltage stabilizer fully automatic micro processor based control card of capacity 200 KVA, three phase oil cooled with Single phase prevention system, indoor type and designed for input variation between 340 V to 460 V with output voltage stabilized at 415 Volts with accuracy of + 1% and speed of correction 8 V/Sec, no load loss less than 0.5%, operating temp - 15C to 45C above ambient and unbalanced load complete with first filling of oil complete, all as specified and directed including additional features as follows: a. High & low voltage cut off system b. Change over switch to by-pass the system

S&F test link (Poly-Carbonated Enclosure) complete all as specified and directed.

Supply, Installation, Commissioning and testing of ESE Lightning Protection A-Supply of THUNDERSTROKE PROTECTOR 60 (E.S.E.) Which is an active lightning conductor designed to conform to the French Standard NFC 17 102: 2011,UNE-21186-2011 ∆T:60 µs for ESE lightning conductors. Its working principle evolves from local electrostatic field that develops naturally around the system as a thunderstorm begins to gather. In the event of descending lightning, an inbuilt triggering device generates high tension pulses at the conductor tip, causing a ‘corona effect’. The international testing laboratory from where the device has been tested By One Lab as per NF C Standard Clause No.C.3 should be duly accredited by ILAC / IEC / ENAC to ensure the genuine testing and device should be CPRI type tested certified on 70 kA, Ageing of both the Test reports should not be more than 5 years (Reports not more than 3 years old are preferred). Device should be consist of BNC Port for the testing purpose in order to check the Internal Circuits. The serial number displayed On the ESE lightning arrester is duly supported with the "Certificate of OEM" issued. (Warranty -5 years) complete all as specified and directed. Make-REMEDIES, INDIA/SG Power Products Private Ltd/Laxmi Power Solutions.

Supply, Installation, testing and Commissioning of RESPL-CBR173 of maintenance free earthing the copper bonded ground rod 17.2mm dia, length 3000mm, should be manufactured by an electrolytic process of 99.99%pure electrolytic copper coating on low carbon, high tensile steel rod along with REMEDIES-ERIC Earth Resistance improvement compound - 25 Kg of (contains mixture of Graphite, Activated Carbon, Sulphate, Silica, Alumina, Iron Oxide, Titanium Oxide, calcium Oxide, Magnesium Oxide, Sodium Oxide, Zinc Oxide, Graphite, Activated Carbon, etc) Backfill compound should be ROHS and thermal stability tested complete all as specified and directed. Make – REMEDIES, INDIA/SG Power Products Private Ltd/Laxmi Power Solutions.

Supply, Installation, Commissioning and testing B-SUPPORTING MAST GI Pipe 10 Meter Long With Supporting Mast Base Plate including Guywire & all accessories + Insulator complete all as specified and directed.

Supply, Installation, testing & Commissioning ESE Lightning Strike Counter -Lightning Discharge Counter Self-powered non re settable Lightning Event Counter (6 digits) mounted on down conductor in IP 67 enclosure with minimum sensitivity 1kA for10/350 μs pulse. (Analog- Type- Digit -6) complete all as specified and directed.

(c) Oil conservator with filter type drain valve and oil level gauge. (d) Dehydrating breather with first filling of dehydrating agent. (e) Explosive vent. (f) Thermometer Pocket. (g) Two earthing terminal on tank body to facilitate fixing of 32x6mm GI Strip. (h) One No thermometer dial type vapour pressure type having range 0-120 degree centigrade with maximum temperature indicator and re-setting device to maximum temperature including needle of temperature gauge max reading panted terminal. (j) Rating plate with terminal plate. (k) Oil drain filter valve. (l) Oil filling hole on top cover with plug. (m) Air release valve/plug. (n) 4 Nos plain solid cast steel detachable rollers. (o) Extra bushing for neut

Supply, Installation, Commissioning and testing of LT feeder pillar box outdoor type made out of 3.15 mm thick CRCA sheet and MS angle iron frame with weather proof canopy, mounted on P

Supply, Installation, Commissioning and testing of distribution transformer of capacity 200 KVA step down outdoor type Copper Wounded ONAN Cooling 11/0.433 KV (at no load) AC 3 Phase 50 Hz on secondary side double wounded oil immersed naturally all air cooled with external tubes/radiator, delta connected as on primary and star connected with neutral brought on secondary side and having tapping at (+) 2.5%, (+) 5%, (+) 7.5% to be changed by hand operated OFF LOAD top changing gear. The maximum temperature rise should not exceed 45 degree centigrade in oil and 50 degree centigrade in HV/LV winding when measured by the resistance method after continuous full load run in ambient temperature the transformer shall confirming to IS 1180 (EE Level-II) 1997 and comprising of following accessories :- (a) 01 No Cable end box on HV side consisting of with 03 Nos porcelain bushing with bushing rods and nuts washers and cable glands suitable for XLPE cable 3 Core 95 Sqmm including cable joint complete adopter box (b) 01 No cable end box on LV secondary side consisting of 04 Nos porcelain bushing with bushing rods and nuts washers and cable glands suitable for XLPE cable 3.5 Core 95 Sqmm including cable joint complete adopter box.

S&F down conductor-70 Sq mm single core copper cable PVC insulated complete all as specified and directed.

S&F earth pit cover complete all as specified. Make – REMEDIES, INDIA/SG Power Products Private Ltd/Laxmi Power Solutions

M&L for pre-casted RCC Pit and earth pit cover for replacing broken/ unserviceable pit cover including cleaning the surrounding area (60cm x 60cm x 60 cm) complete all as specified and directed

M&L for Galvanized iron strip 32 x 6 mm with saddles and fixing screws on porcelain insulators buried in ground complete all as specified and directed

M&L for Aluminium strip 25mm x 3.15 mm fixing with and including porcelain insulators on roof and floor complete all as specified.

M&L single disc insulator porcelain vitreous type 145 mm height and 225 mm dia ball and socket type brown, assembly for tension with tension clamp for conductor 11 KV complete as all specified and as directed including taking down old unsv one complete all as specified and directed.

S&F funnel alongwith wire mesh in renewal of missing/ unserviceable item all as specified and directed

S&F porcelain supporting insulator of existing size / adequate size fixing on wall / roof for insulating and supporting the lightning arrestor strips to protect during lightning complete all as specified and directed.

M&L for PCC block for fixing of GI pipes for termination rods complete including suitable pipe all as specified and directed.

S&F single pointed air termination aluminium rod 12 mm dia , 300 mm long, complete all as specified.

S&F voltage stabilizer for automatic operation, three phase, naturally oil cooled, indoor type & designed for input variation between 300 V to 480 V with output voltage stabilized at 415 with accuracy ± 2.5% and speed of correction 8 Volts per second and of capacity 200 KVA complete all as specified and directed.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor, of size 120 sq mm 3.5 core complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m depth for foundation, laying of cables, etc. and getting out in soft / loose soil complete all as specified

Excavation in trenches n.exc 1.5m vide and n.exc 1.5m depth for foundation, laying of cables, etc. and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm depth in soil complete all as specified and directed.

Removing excavated material (soil) n.exc 50m and depositing where directed at a level n.exc 1.50m complete all as specified.

Supply and spreading clean dry sand in trenches for cushioning for cable protection complete all as specified and directed. Note: The punned down thickness shall only be measured.

Supply and laying sub class 'B' bricks laid across the cable for cable protection complete all as specified and directed.

M&L for providing platform for voltage stabilizer of size 3mx3mx1.2m height from GL including excavation in trenches PCC 1:5:10 type E2 for foundation brick work in cement mortar 1:6 PCC 1:2:4 and width of brick wall 35cm type B1 in copping plaster 10mm thick in cement mortar 1:6 om brick/complete surface PCC 1:4:8 type B1 sub base 75mm thick as in floor, PCC 1:2:4 type B1 100mm thick floor using extra cement returning filling and removal of surplus soil, chain link fencing 1.8m high made out of 4mm dia GI wire 150x100mm mesh MS work angle iron 50x50x6mm as fencing post in embedded in brick/PCC work at 2 mtr interval each side as approved 1 No steel gate (3.5m clear) span with locking arrangement made out of 15mm dia MS rod & 50mmx50mmx6mm angle iron frame painting with 2 coats of aluminium paint over a coat of red oxide primer and 3 coats of white washing on cement work including ISMC 100 channel 2 Nos for fixing transformer complete all as specified.

S&F cable jointing kit 11 KV grade cable for straight through joint complete with jointing material heat shrink type and outdoor type and accessories suitable for 3 core XLPE armoured, AI conductor cable of size 50 to 95 sq mm complete all as specified and directed.

M&L for cement concrete for foundation fillings and mass concrete in 1:4:8, type D2 (using 40 mm graded stone aggregate) complete all as specified and directed.

M&L for cement concrete 1:3:6, type C2 (using 40 mm graded stone aggregate) for mass fillings of poles concrete complete all as specified and directed.

M&L for well burnt sub class ‘B’ designation 75 bricks as mechanical protection to under ground cables laying with length of the bricks equal to the width of the trench complete all as specified and directed by Engr-in-Charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 11000 Volts grade with stranded aluminium conductor of size 95 Sq mm 3 core complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 Sq mm 4 core complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 95 Sq mm 3.5 core complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 240 Sq mm 3.5 core complete all as specified and directed.

M&L for switch air break, gang operated triple pole, mechanically operated, mounted on insulator and steel frame, with operating mechanism worked from ground level, for current rating upto 200 Amps 11000 Volts (12 Insulator) alongwith fuse system complete all as specified and directed.

ral out side the cable box providing independent earthing for neutral. (p) First fill of transformer oil confirming to IS 335 and tested upto 60KV dielectric strength. (q) Type of connection= Delta star (r) Vector group= DYN11

M&L for lighting arresters expulsion type complete with all fittings transmission class, discharge capacity 65KA suitable for 11000 Volts complete all as specified and directed.

M&L for cable jointing kit for 11 KV (Earthed) grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 95 sqmm complete all as specified and directed.

S&F cable jointing kit for 1.1 KV (earthed) grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable for size 240 Sq. mm complete all as specified.

M&L in repairs for earthing complete with galvanized steel earth plate electrode 600mm x 600mm and 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanized earth Wire 4.0 mm (up to 7.5 m in length from earth plate) by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate no.3 of SSR part I including necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 8mm dia at 150mm c/c in both ways as reinforcement, watering funnel, 20 mm dia light grade for protection of earth electrode, 20 mm dia GI pipe light grade for watering complete all as specified and directed by Engr-in-Charge and tested on completion. Note : The rate is inclusive of necessary earth work, RFR and removal etc

M&L for earthing complete with galvanized steel earth plate electrode 600mm x 600mm and 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanized earth strip 32X6 mm dia (up to 7.5 m in length from earth plate ) by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate no.3 of SSR part I including necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 8mm dia at 150mm c/c in both ways as reinforcement, watering funnel, 20 mm dia light grade for protection of earth electrode, 20 mm dia GI pipe light grade for watering complete all as specified and directed by Engineer in charge and tested on completion. Note : The rate is inclusive of necessary earth work, RFR and removal etc. complete all as specified and directed.

Construction of transformer shed for transformer of capacity upto 300 KVA complete all as specified and show on Drg No CESZ/TD-1110/2011 Sheet 1/1 and 2/2 dated 01.12.11

S&F in repair cross arms bracing supports, clamps and back plate fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts in any shape or size as indicated or directed and inclusive of one primer coat of red oxide zinc chrome, one under coat and one finishing coat of aluminium paint complete all as specified.

S&F anti-climbing device; spikes type fabricated out of M.S. bars (round, square and flat) including nuts, bolts, washers and welding in two halves made to shape to suit the cross section of the pole complete all as specified and directed.

S&F MS tubes, light grade, galvanised, 80 mm bore, laid in trenches or under floor or road or fixed with pole for protection of electric cable complete all as specified and directed.

S&F MS tubes, light grade, galvanised, 100 mm bore, laid in trenches or under floor or road or fixed with pole for protection of electric cable complete all as specified and directed.

S&F danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters written in English, Hindi & Urdu" figures and conventional skull and bones in signal red colour and fixed with MS clamps, bolts and nuts of approved size for HT, 25x20cm size complete all as specified and directed.

M&L GI tubing medium grade ISI marked complete with all necessary fittings of sizes 100 mm bore in trenches including taking down of old rusted GI pipes complete all as specified and directed.

All as per ser item No. 54 here-in-before but of size 150 mm complete all as specified and directed.

M&L for cutting of cast iron pipes of 150/100 mm dia and reducing to required length for insertion of tee, bends elbow etc complete all as specified and directed.

S&F GI flange thread type (Chudi type) type suitable for 150 mm bore GI/CI pipe line including welding with pipe, nuts, bolts gasket 3 mm thick complete all as specified and directed.

S&F in repair, GI fittings for pressure pipes such as bends, (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc). Tee pieces single branch "Y" junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs upto 150mm dia complete all as specified and directed.

M&L run lead joint suitable for spigot and socket pipes 150 mm dia spigot including taking out of old one complete all as specified and directed.

S&F galvanised iron sluice valve ISI mark (PN-1.6) confirming to IS 14846-2000, flanged ends drilled having stainless steel / brass spindle with cast iron wheel at top complete with nuts, bolts, washers and gaskets of size 150 mm bore complete all as specified and directed.

S&F galvanised iron non return valve without by pass arrangement , swing type, of size 150 mm bore, confirming to IS 5312, flanged ends with nuts bolts, washers complete including taking down of old one complete all as specified and directed.

M&L for galvanised iron Air valves with two air outlets, conforming to IS-14845 of size 150 mm dia bore and fixing up in cast iron water supply mains complete all as specified and directed by Engr-in-Charge.

M&L for providing PCC 1:2:4, type B1 (using 20mm crushed stone aggregate) as in copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating, as directed concrete including necessary formwork and finishes the exposed surfaces of concrete complete all as specified and directed.