8830/E8

Amount

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing), and removing rubbish off the Premises, complete all as specified and as directed.

Demolition of cement concrete (Un-reinforced) of any description and in any position not otherwise specifically provided for all as specified and directed.

Dismantling Reinforced Cement Concrete of any description and in any Position not otherwise specifically provided for, complete all as specified and as directed.

Demolition of Brick Work built in Cement Mortar including all Quoins, Arches, Pillars, etc. of any descriptions, complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutter from frames) of any sizes nexc 1.5 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frames) exc. 1.50 Sqm and n.exc 4 Sqm each complete all as specified and directed.

Taking down cement plaster of any description on brick work or stone msonary wall including racking ot joints hacking for key scrubbing down with water etc. complete all as specified and directed.

Taking up or down Steel Water Tubing 15mm dia (bore) including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed.

Taking up or down Steel Water Tubing 20mm dia (bore) including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed.

Excavating in post holes (or similar holes) each n. exc. 0.5 cum, getting out returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc. 25 cm watering and removing surplus soil to distance n. exc 50 m and making good surface complete all as specified and directed.

M&L Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L Hardcore (broken stone or boulders) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

M&L Anti Termite Treatment of voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed

M&L Cutting chase, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of laddings, steps, cills, sushades, shelves, lintels etc and cutting chase for concealed water tubing or concealed coduit wiring etc and making good cutting grith n exc 10 cm girth on brick walls complete all as specified and directed.

Material and labour Chipping of unsound/weak concrete materials of 30mm average thickness from slabs/chajja/ fin fascia with lightly packing materials by ait blasting or sand blasting including tapering all edges, making square shoulders of cavities etc upto four storey height of building including necessary scaffolding and safety measure complete all as specified and as directed by the Engr-in-Charge.

M&L Removing rust from existing corroded reinforcement by any means and application of Rust Remover such as Hind Rust Clean (M/s Hindcon) or equivalent asper list of makes and then washing the same to make the reinforcement scale free complete all as per the direction of Engineer-in-Charge Note : Payment to be made on 25% exposed area.

M&L Application of anticorrosive paint such as Hind Anti Rust (M/s Hindcon) or equivalent asper list of makes on cleaned reinforcement as per manufacturer's specification complete including labour and material as per direction of Engineer-in-Charge. Note : Payment to be made on 25% exposed area.

M&L Application of bonding coat based on polymer modified cementious material such as Nitobond SBR/Hind Styrene BR (M/s Hindcon) or equivalent asper list of makes @ 0.50 Kg/Sqm (due to rough concrete surfaces) to act as bonding agent between old and new concrete including material and labour as per manufacturer's specification complete all as per direction of Engineer-in-Charge.

M&L Pressure guniting at a pressure not less that 6Kg/Sqcm to surface of column, beam, ceiling, facia and similiar structural members in polymer modified concrete with mix ratio 1:1.5:3 (1 cement : 1.5 Coarse Sand : 3 Stone aggregate of 10mm nominal size) admixed with acrylic latex polymer such as Hind Styrene BR/Nitobond SBR (M/s Hindcon)or equivalent asper list of makes @ 3.00 Kg per Sqm and plasticiser Hind Plast Super/Conplast SP 337 (M/s Hindcon) or equivalent asper list of makes @ 100Gms per Sqm for an average thickness of 50mm (the concrete to be applied when the bonding coat is still green) including material and labour, scaffolding and formwork etc. as per manufacturer's specification complete all as per direction of Engineer-in-Charge.

M&L Plain Cement Concrete 1:3:6 (40 mm graded crushed stone aggregate) type C2 as in foundation filling and mass conc, etc., complete all as specified and as directed.

M&L Plain Cement Concrete type C-1, (1:3:6) (20mm graded crushed stone aggregate) as in Coping bed plate,hold fast etc,block benching,channeling slightly rounded or chamfered angle and throating including form work and finishing all exposed faces of cement concrete complete all as specified and as directed.

M&L Cement Concrete Type B0 (1:2:4) (12.5mm graded crushed stone aggregate) as in padding and benching and filleting complete all as specified and directed.

M&L Brick work using Pulverizes fly ash bricks of class designation 75, straigth or curved on plan exc 6m mean radius built in CM (1:4) cmplete all as specified and directed.

M&L Brick Work with Half Brick work using Pulverizes fly ash bricks of class designation 75, built in Cement Mortar 1:4, Straight or Curved on Plan to any Radius, complete all as specified and as directed.

S&F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to cowkhats complete all as specified and directed.

S&F for 2nd class hardwood 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats as specified in SSR Part-I 2009.complete all as specified and directed.

S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, fixing in opening as per Specifications and Drawings shown in MES Schedule Part-II, complete all as specified and as directed.

S&F Plain Colour Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing etc complete all as specified and as directed.

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi-chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality including Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperature 1.40 mm and required accessoreis, complete all as specified and directed by Engineer-in-Charge. Note: (1) For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Net Opening will be measured for payment purpose. (2) The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories.

S&F Aluminium anodised, barrel tower bolts of extruded section, 200 mm long and fixed with steel screws complete all as specified and directed.

S&F Extruded aluminium alloy handles, fabricated type, anodised 150mm long complete all as specified and directed

S&F 300mm long Aluminium alloy, anodised, Sliding Door Bolt with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Floor door stopper of aluminium aloy body and tongue, anodised with hard drawn steel spring (overall length of cover plate 150mm) complete all as specified and as directed.

S&F Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and as directed.

S&F curtain rail 20mm dia fix in repair, mild steel, chromium plated with fixing brackets, stops, rollers and fennels etc of drapery rod fixed in position as in repair complete all as specified and as directed

S&F Bracket for fixing Fancy type,Chromium Plated 20mm dia curtain rod/ drapery rod etc as in repair complete all as specified and as directed.

M&L Mild steel Steel Work in Tubular Trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conform-ing to IS:1161-1979 grade St.-240, complete all as specified and as directed.

M&L Mild steel Framed Work such as Grills, Gratings, etc. with ends of Bars shouldered and/or riveted, or forged into Spikes; Framed Guard Bars; Barred Iron Doors; Ladders; Framed Balusters; Walk Ways; Railings; Framework of Water Tanks and Similar Work, conforming to Fe-290, Gde-E-165, complete all as speci-fied and as directed.

M&L for Pressed steel frames for doors with one or more rebates size of frame 125 x 60 mm including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed. Note:- Pressed Steel Frame should be filled with PCC 1:3:6 Type C-0 (Using 12.50mm graded stone aggregate) and cost of PCC shall be deemed included in quoted rate

M&L for Pressed steel frames for doors with one or more rebates size of frame 105 x 60 mm including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed. Note:- Pressed Steel Frame should be filled with PCC 1:3:6 Type C-0 (Using 12.50mm graded stone aggregate) and cost of PCC shall be deemed included in quoted rate

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated/semi corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw complete all as specified and directed.

M&L Cement Concrete type D2(1:4:8) using 40mm graded crushed stone aggregate 75mm thick as in sub base of floor, foundation filling etc complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6) type C-2 (Using 40mm graded stone aggregate) as in plinth protection laid in panels, finish the top surfaces even and smooth without using extra cement complete all as specified and directed Note:- Construction joints will be provided at interval of 2.5m length and filled with bitumen 80/20 mix with sand in ratio of 1:3 and cost of the same shall be deemed included in quoted rate

M&L Cement Concrete type B0 (1:2:4) (12.5mm graded aggregate) 25mm thick, in Flooring, finishing concrete surfaces even and smooth complete all as specified and as directed.

M&L Non-skid Ceramic Coloured Tiles, 7.0mm to 8.0mm thick (square/rectangular), area of each tile exc 0.11 sqm but not exc 0.18 sqm in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over 15mm thick screed bed (1:6) in cement mortar complete all as specified and as directed.

M&L Non-skid Ceramic Coloured Tiles, 7.0mm to 8.0mm thick (square/rectangular), area of each tile exc 0.18 sqm but not exc 0.38 sqm in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over 15mm thick screed bed (1:6) in cement mortar complete all as specified and as directed.

M&L Non-skid Ceramic Coloured Tiles, 7.0mm to 8.0mm thick (square/rectangular), area of each tile exc 0.18 sqm but not exc 0.38 sqm on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L Glazed Ceramic Coloured Tile 450 x 350 x 7.0mm thick on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L Granite (of any type) Work (Table rubbed and polished) 18 to 20 mm thick, in Steps, Cooking Platforms and like, Set in Screed bed of 20mm thick in Cement Mortar 1:4 including Pointing in White Cement 1:2 using Marble Dust with admixture of Pigment to match with Shade of Granite including Cutting and Polishing including half round edges, complete all as specified and as directed.

M&L Pre polished Chequered cement concrete tiles of size 300mm x300mm x25mm thick, with grey cement and no pigment, jointed in neat cemnt slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

S&F Machine cut kota stone slab flooring 20-25mm thick (size 550mmx550mm) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite finish polishing complete over 20mm thick 1:6 cement mortar screed bed complete all as specified and as directed.

M&L Preparation of plastered surfaces of roof and laying 3mm thick APP (Atactic Polypropylene Polymer) modified prefabricated five layer, weight not less than 3.6 kg/Sqm water proofing membrane, black finished reinforced with non woven polyester matt laying over a coat of bituminous primer @ 0.40 Ltr / Sqm and two coats of Bitumen based UV reflective paint with aluminium finish over APP membrane including taking down . The membrane shall be laid using butane torch and sealing all joints etc all as specified and directed.

M&L Rendering 15mm thick in Cement Mortar 1:4 on fair faces of Brick Walls or on Concrete Surfaces, finishing plastered surfaces Even and Smooth without using Extra Cement complete all as specified and as directed.

M&L rendering 10mm thick in CM (1:6) on other than fair faces of brick work finishing surfaces even & fair without using extra cement complete all as specified and directed

M&L for 10mm thick bedding over roof surfaces including WPC in cement mortar 1:3 complete all as specified and directed. (NOTE:-WPC shall be measured and paid separately)

M&L rendering 5mm thick in CM (1:3) as in ceiling surfaces even & smooth without using extra cement complete all as specified and directed.

"Supply only" liquid water proofing compound (ISI marked) complete all as specified and directed. Make:- STP NO 1/ PEDILITE(DR FIXIT)/ FOSROC/ CICO/ SIKA/ Icannano

M&L Preparing new Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion over a coat of primer and applied over 1.5mm thick (appx) water proof wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed.

M&L preparing new plastered surfaces of ceiling surface and and applying Two Coats of Distemper Oil Emulsion over a coat of primer over and including 2mm thick water proof wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed. complete all as specified and as directed.

M&L Complete removal of existing Treatment of old decorated Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion over a coat of primer and applied over 1.5mm thick (appx) water proof wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed.

M&L for applying polymer modified cement mortar rendering 20mm thick in CM 1:3 on wall duly mixing polymer modifier "Nitobond SBR of M/s Forsoc Chemical India (Pvt) Ltd" or "Hind Styrene BR of Hindcon Chemical Ltd" or equivalent make of M/s Pidilite Industries @ 7 Litre per bag of cement complete finished even and smooth without using extra cement complete all as specified and as per manufacturer's specification.

M&L preparing newly plastered surfaces and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

S&F 4.8mm thick frosted glass panes and glazing with oil putty in square nexc 0.5 Sqm each pane complete all as specified.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples complete all as specified and as directed.

M&L Preparing old Wooden Surfaces of any description not otherwise decribed over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed.

M&L Preparing new Steel or Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Red Oxide/ Zinc Chrome Primer, complete all as specified and as directed.

S&F CPVC pipes 20 mm outer diameter of SDR 11 & plain CPVC SDR 11 fittings fixed on Walls, Ceiling or laid in Floors or any other Situation, etc up to four stories height of bldgs. complete as all specified and as directed.

S&F CPVC pipes 25 mm outer diameter of SDR 11 & plain CPVC SDR 11 fittings fixed on Walls, Ceiling or laid in Floors or any other Situation, etc up to four stories height of bldgs. complete as all specified and as directed.

S&F for Stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roof Bore in pipe in 75mm to 150mm complete all as specified and directed

S&F in repair for single socketed PVC (SWR) pipe Type "B" 75mm bore with rubber ring joint any radius complete all as specified and directed

S&F in repair Single socketed UPVC (SWR) pipe Type "B" 110mm bore with rubber ring joint any radius complete all as specified and directed.

S&F work for UPVC (SWR) 75mm bore cowls complete all as specified and directed.

S&F for UPVC (SWR) 75mm bore bend any radius complete all as specified and directed

S&F UPVC (SWR) 110mm bore bend any radius and Jointing with Solvent Cement, as in repair complete all as specified and as directed.

S&F UPVC (SWR) Junction 75mm bore (dia), Single (Single T) equal or unequal and Jointing with Solvent Cement complete all as specified and as directed.

S&F UPVC (SWR) Junction 110 mm bore (dia), Single (Single T) equal or unequal and Jointing with Solvent Cement, as in repair complete all as specified and as directed.

S&F UPVC (SWR) 110mm bore Branch pieces, single (equal or unqual), ordinary or inverted (spigot or socket type) or with parallel branches or fitted with oval access doors as in repair complete all as specified and directed.

S&F UPVC (SWR) Nahani/Floor Trap 75mm bore (dia) Outlet, Plain with Grating and Jointing with Solvent Cement, as in repair complete all as specified and as directed.

S&F PVC connection 15mm size with PTMT nut of length 450mm complete all as specified and directed.

S&F Brass chromium plated fancy type pillar tap screwed for 15 mm bore of pipe etc.incl necessary fittings & fixtures complete all as specified & directed.

S & F in repair for chromium plated Bib taps for 15 mm bore pipe complete all as specified and directed.

S&F 20mm bore stop valve concealed type, cast copper alloy, chromium plated , screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F 20mm bore stop valve, fancy type cast copper alloy, chromium plated , screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in repair for Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipewith 1.2 Meter Long PVC Tube & Wall Hook including making connections and fixed in position complete in all respect as specified.

S & F in repair for 15mm bore brass chromium plated 2 Way Angular Valve with Wall Flange complete all as specified and directed.

S&F Stainless Steel Towel rail of size 15mm dia 600mm long decorative type fixed with walls including necessary fittings etc complete all as specified and as directed.

S&F 125 mm dia brass chromium plated shower rose with or without swivels joint for fixing to 15 mm bore pipe etc complete complete all as specified and directed.

S&F Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back or Angle Back Type) with 32mm dia Brass Chromium Plated Waste Fitting, a pair of Cast Iron Brackets duly painted including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 including taking down/out unserviceable Wash Hand Basin and connected Items, complete all as specified and as directed.

S&F Vitreous China Colour Wash down Water Closet Pan (Pedestal Pattern) with "p" or "s" trap front or back inlet including fixing Bolts with and excluding 10 litre capacity low level Flushing Cistern matching with water closet colour with inlet ball valve float handle and providing 32mm dia PVC flush pipe including plastic water closet seat with flat botton cover (coloured) fixed with mild steel chromium plated or aluminium hinging device including taking down old unserviceable one complete all as specified and as directed.

Supply and fixing in repair 10 litre capacity low level PVC flushing cistern (any colour), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete as directed.

S&F Rotational Moulded Polyethylene (HDPE) Water Storage Tank 500Litre Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I including provision of 25mm x 100mm GI nippples with check nuts for inlet, outlet wash, float valve and overflow pipe including Lowering of old/unserviceable Water Storage Tank of any description, complete all as specified and as directed.

Taking down point wiring (light, fan, socket and power complete including fixtures and fittings such as switches ceiling roses, pendents , regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody for refixing or for taking credit (credit for above items should be made as per conditions separately) and making good distrubed surfaces of walls, floors, etc. including cleaning all and specified and directed.

M&L for Point wiring with PVC insulated and unsheathed FRLSH cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS - 694 1990 drawn through and including PVC concealed conduit 20mm dia medium duty with all accessories including fabricated 1.6 mm thick MS terminal boxes fixed flush with wall surface with 3 mm thick plastic masonite laminated sheet top cover fixed with cadmium screw for mounting switches, sockets, regulator etc including 1.5 sq mm FRLSH stranded PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified including Cutting chase, pinning in making good to facings where required and pointing in cement mortar 1:3 for one light or fan point controlled by one switch single pole one way for light/ ceiling fan/ exhaust fan/call bell point/ Switch socket outlet 5 amps complete all as specified and as directed. Note: (i) Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.

All as per item No 95.00 here-in-before but one 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed by Engineer-in-charge.

All as per item No. 95.00 here-in-before but one 3 pin 5 amps switch socket outlet on the independent board with other switch complete all as specified and directed by Engineer-in-charge.

M&L Point wiring with 2.5 sqmm (Nominal Area) PVC insulated stranded single core unsheathed FRLSH copper conductor cable 1100 Volts grade drawn through with and including PVC concealed conduit 20mm dia medium duty with all fittings and accessories of casing caping (like Tee, Bend etc) complete fixed to walls / ceiling etc with and including 2.5 Sqmm (nominal area) PVC insulated unsheathed, stranded, single core FRLSH copper cable as earth continuity wire connecting to common earth point (including supply & fixing of 1.6 mm thick pressed mild steel terminal boxes of suitable size with 3 mm thick PVC /plastic laminated sheet, top cover suitable sizes of brass screws and washers etc. including Cutting chase, pinning in making good to facings where required and pointing in cement mortar 1:3 for mounting sockets for 5 pin, 16 Amp socket outlet on independent board complete all as specified and directed. Note: (i) Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.

S&F Switch piano, flush type, SP, one way, 5/6 Amps 230/240 Volts, white/ivory finish complete all as specified and directed.

S&F Switch socket combination multipurpose 2 in 1, 3 pin 6 Amps 230/240 volt flush type complete all as specified and as directed.

S&F Socket outlet 3/5 pin, 6 Amps, 240 volt flush type complete all as specified and as directed.

S&F Switch socket combination multipurpose 2 in 1, 3 pin 15 Amps 230/240 volt flush type complete all as specified and as directed.

S&F Ceiling rose surface bakelite three terminals 240 volts complete all as specified and as directed.

S&F ceiling fan regulator electronic Step type, solid state, 240 volts, complete all as specified and as directed

S&F 9W LED bulb, 6500k, PF>0.9, CRI>80 lumen efficacy warmlight/ natural white alongwith PVC Lamp holder complete all as specified and directed by the Engr-in-Charge.

S&F Energy efficient LED fittings of capacity 1 x 10W suspended type / wall mounted type complete with LED tube Lamp and fitting with copper flexible PVC cable of 0.50 sq mm twin core not more than one metre in length complete all as specified and as directed.

S&F Energy efficient LED fittings of capacity 1 x 20W suspended type / wall mounted type complete with LED tube Lamp and fitting with copper flexible PVC cable of 0.50 sq mm twin core not more than one metre in length complete all as specified and as directed.

S&F building security light pressure die cast housing with individual LEDs with modular secondary optics security light luminaires 35 watt LED with 50mm dia light grade GI pipe bent to shape of 45'' 1.5 mtr long and nuts bolts including fixing arrangement after taking down old unserviceable one complete all as specified and directed by Engineer-in-Charge.

Taking down unserviceable rusted / damaged MCB DBs of any type and way along with any type MCB and keeping serviceable MCB in safe custody in re-use in the work and making good to the distubed surfaces of walls etc. complete all as specified and as directed.

S&F Sheet metal enclosure for DB's when MCBs to be used 8 way single pole and neutral double door with 200 amps rated bus bar complete 240 volts complete all as specified and as directed.

S&F MCB SPN DB made up with sheet metal double door, phosphorised, power coated, neutral link, earth bar and din rail, 4 way with 200 amps rated bus bar, 240 volts complete all as specified and as directed.

S&F MCB TPN DB made up with sheet metal, phosphorised, power coated, neutral link, earth bar and din rail, 8 way TPN with 200 amps rated bus bar, 415 volts complete all as specified and as directed.

S&F MCB 6 to 32 Amps, SP, 240 Volts , 'C' curve breaking capacity 10 kA complete all as specified and as directed.

S&F MCB 6 to 32 Amps, DP 240 Volts ,C- Curve breaking capacity 10 KA including necessary connection complete all as specified and as directed.

S&F MCB TPN 40 to 63 amps 240 volts 10KA breaking capacity, C-Curve complete all as specified.

Taking down old burnt/unserviceable submain wiring with aluminum/copper conductor PVC insulated cable of any size drawn through PVC casing caping/ PVC Conduit pipe including GI wire accessories etc. and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M&L Sub main wiring with 2 runs of single core FRLSH type PVC insulated unsheathed stranded copper conductor of size 4.0 Sqmm and one run of PVC insulated unsheathed multistrand copper conductor FRLSH type of size 4.0 Sqmm as earth lead drawn into rigid non metalic PVC conduit of size 20 mm dia including all fittings complete all as specified and as directed. Note:- Two runs of 4 Sqmm conductor as main wire and one run of 4 Sqmm conductor as earth wire with one run of PVC conduit shall be measured as one unit.

S&F sub main wiring two run of single core PVC insulated unsheathed stranded copper conductor of size 6 sqmm & one run of PVC insulated unsheathed stranded copper conductor of size 6 sqm as earth lead drawing into rigid non metalic PVC conduit of size 20mm dia including taking down old unsv complete all as specified. Note: Two run of 6 sqmm cable and one run of 6 sqmm cable will be measured as single length.

Taking down and refixing of electric water heater storage type of any capacity in same position or other position and connection alongwith minor accessories complete all as specified and directed

Taking down and opening out the ceiling fan/wall mounted upto1200/1400 mm sweep for inspection, removing bush / bearing, cleaning of bush / bearing, replacement of unserviceable / worn out bearing / bush, shaft, removing burnt out coils from the slots, cleaning and repairing of slots complete including materials like split pin, rubber reel etc and reassembling and refixing of fan complete with and including minor Spares, if any required complete all as specified and as directed. Note : Spare parts shall be measured & paid separately.

Rewinding of ceiling fan motor with super enamelled copper winding wire of suitable size & varnishing including testing of fan after rewinding complete all as specified.

Supply only ball bearing suitable for 1200/1400mm sweep Ceiling fan of any make.

Supply only capacitor of 2.5 mfd for Ceiling Fan

Supply only gun metal bush of suitable size for ceiling fan of sweep 1200mm/1400mm as per existing one complete.

Supply only shafts for ceiling fan suitable for 1200mm sweep

Supply only PVC connector for Ceiling Fan

Supply only fan blades for Ceiling fan suitable for 1200mm sweep/1400mm sweep.

Supply only nuts, bolts, for Ceiling fan

M&L for painting of ceiling fan/wall fan/exhaust fan of any size and sweep complete with synthetic enamel paint by spraying including filling with cavities with filler, after cleaning all dust etc complete all as specified and directed by Engineer-in-Charge.

Materials and labour Earthing complete with galvanised steel earth plate electrode 60 Cm x 60 Cm x 6.00 mm thick buried in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to GI wire 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of GI or steel, GI strip projected by 15 mm bore light grade GI pipe and other end connected to earth test point as directed including funnel with watering pipe 20 mm bore light grade galvanised iron, wire mesh, charcoal or coke common salt laid in alternative layer of 15 cm (complete thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1, 50 mm thick pre-cast RCC (1:2:4) type B-1 normal mix cover slab reinforced with 8 mm dia TMT bar 10 Cm c/c both ways and single handle of 10 mm dia round bar including necessary excavation, earth work etc. in soft / loose soil and disposal pf soil to a distance n. exc. 50 m and necessary testing on completion all as shown in electrical plate No. 3 MES Schedule Part-I complete all as specified and as directed.

Excavation in trenches not exc. 1.5 Metre wide and not exc. 1.50 Metre in depth for foundation etc. or for shafts, wells, cess pits, manholes, pier holes, pipe, cable etc. not exc. 10 Sqm on plan and not exc. 1.50 Metre in depth and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 Cm as in soft/loose soil complete all as specified and directed.

Removing excavated material ( soils of any type) n exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

Supply and laying dry coarse sand as in cushioning of under ground electric cable in trenches, laid to a uniform thickness of 23 Cm (15 Cm under the cable & 8 Cm over the cable) and gently punned down to 18 Cm thickness complete all as specified and as directed by the Engr-in-Charge. Note:- Thickness after punning down shall be measured for payment.

Supply and laying in trenches Bricks, sub class 'B' over burnt (kiln burnt) old size bricks, laid flat dry with width of the bricks laid to the axis of the cable for protection of cable complete all as specified and as directed by the Engr-in-Charge.

Laying only in trenches Old serviceable bricks obtained from taking out old unserviceable XLPE cable, laid flat dry with width of the bricks laid to the axis of the cable for protection of cable complete all as specified and as directed by the Engr-in-Charge.

Taking out unserviceable UG cables of any type and any sizes from trenches etc and removing from the site of work complete all as specified and directed. Note:- (i) Serviceable bricks obtained shall be stacked properly for re-use. (ii) Excavation and earth work shall be measured and paid separately under relevant item of these schedule.

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 35 Sqmm 3.5 core in trenches/ duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as directed by the Engr-in-Charge.

Materials and Labour Cutting existing road / path etc for taking out cable and proction pipe and making good the disturbed surfaces with cement concrete type C2 ( 1:3:6,) using 40mm graded crushed stone aggregates) of suitable depth complete all as directed by Engineer-in-Charge.

Taking up or down existing pipe line of 25mm dia (bore) from trenches, wall or floor etc. including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed. Note:-Excavation and earth work shall be measured and paid separately.

Supply and Laying Steel Water Tubing 25mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, laid in trenches or any other Situation, complete as all specified and as directed.

Supply and Laying Steel Water Tubing 25mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, in wall/ floor/ceiling or similar Situation, complete as all specified and as directed.

M&L for 40mm bore GI tubes light grade in trenches with all fixing accessoires (clamps, nut, bolt and washer etc) complete all as specified and directed.

Supply and fix 25mm bore Gun metal, globe or gate valves (ISI marked) ( Class-I) with iron wheel head, screwed both ends in repair complete as specified and as directed.

S&F of sheet glass with ordinary quality 4.80mm thick glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed

S&F of 75mm butt hinges heavy duty cold rolled stainless steel and fixed completed all as specified and directed.

DIPAK ENTERPRISE (BID ID -3422101)

M/S L.R.ENTERPRISES (BID ID -3419690)

PUTUL CONSTRUCTION CO. (BID ID -3419600)

MODERN AGENCY (BID ID -3419688)

SUDHA ENTERPRISES (BID ID -3417760)

M/S SRINIVASA CONSTRUCTION (BID ID -3420878)