SPL REPAIR OF OR MD ACCN BLDG NO P07 P7 1 TO 7 12 JADHUNATH ENCLAVE OF ENGR SQN AT NAMS

Amount

Demolition of cement concrete (unreinforced) in ground floors and paving exc. 15 cm thickness including part chipping (below or above ground level) complete all as specified and directed.

Dismantling of terazoo in dado, walls tiles, including bedding but backing and rubbish off permises complete all as specified and directed.

Demolition of reinforcement cement concrete above the ground floors not exc. 15 cm thickness (Reinforcement cut as required to facilitate demolition) such as cooking platform, chajjas , staire case etc complete all as specified and directed.

Material and labour for post construction antitermite Treatment of soil under existing floors using emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed.

Material and labour for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or rectangular) area of each tile exc 0.18 Sqm but not exceeding 0.38 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes incl rubbish off the primises etc complete all as specified and directed..

Material and labour for Non-skid ceramic coloured tiles 7 to 8 mm thick (Square or rectangular) area of each tile exc. 0.18 Sqm but not exceeding 0.38 Sqm, as in skirting,dado in vertical surfaces etc. and including 10 mm thick backing plaster 1:3 etc complete all as specified and directed.

Material and labour for Non-Skid ceramic colour tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed 15 mm thick rendering in CM 1:6 complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

Material and labour for Green marble work 18 to 20mm thick (table rubbed and polished) laid over 15 mm thick screed bed of CM 1:6 as in flooring and jointed with grey cement slurry mixed with pigment to match the shade, rubbing & polishing complete all as specified and directed.

Material and labour for Green Marble work 18 to 20mm thick (table rubbed and polished) laid over 10mm thick cement plaster of CM 1:3 as in riser /skirting and jointed with grey cement slurry mixed with pigment to match the shade, rubbing and polishingand complete all as specified and directed.

Material and labour for 25 mm thick cement concrete (1:2:4), type B-0, using 12.50 mm graded aggregate as in floors including finishing the surface rough & even for receiving kota/tiles complete all as specified and directed.

Material and labour for glazed ceramic coloured tiles of size 450 mm x 300 mm x 7 mm on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including rendering 10 mm thick in cement mortar (1:4), etc. complete all as specified and directed.

Demolition of brick work built in cement mortar including all quions, arches, pillars, etc complete all as specified and directed.

Material and labour for Brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in CM (1:6) complete all as specified and directed.

Material and labour for Brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 as in half brick thick wall complete all as specified and directed.

Material and labour for PCC 1:4:8 type D-2 (using 40mm graded agg) in foundation, sub base, mass concrete etc. complete all as specified and directed.

Material and labour for 75 mm thick cement concrete 1:3:6 type C2 , using 40 mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

Material and labour for PCC 1:2:4 type B1 using 20 mm graded stone aggregate for insertion of hold fast incl necessary form work etc complete all as specified and directed.

Material and labour for repairing of RCC projection, chajjas, facia,bands, shelves, beams, RCC railing, balcony and similar works by dismantling of loose/ disintegrated portion RCC at any height and in any sitution floor (including provn of support, formwork and welding of reinforcement if required with wire mesh of weight 3 kg/ sqm and dubbing/ filling with PCC (1:2:4), type B-0, using 12.5 mm graded aggregate,15 to 25 mm thick after applying cement slurry @ 3 kg/sqm, finished even and smooth to desired shape and applying two coats of wheater proof emulsion paint to match with existing surfaces complete all as specified and directed.

Taking down cement plaster on wall/ceiling/roof etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed.

Material and labour for 15mm thick cement plaster in CM 1:4 on fair faces of brick or concrete work and finishing the surface even and smooth (without using extra cement) including WPC @ 3% weight of cement etc. complete all as specified and directed. Note : WPC will be measured and paid separately under appropriate items.

Material and labour for 15 mm thick rendering on fair faces of brick or concrete surfaces in CM (1:6), finished even and smooth (without using extra cement ) complete all as specified and directed.

Material and labour for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces of ceiling and finishing the surfaces even and smooth complete all as specified and directed.

Material and labour for applying two coats of oil bound distemper over a coat of primer including 2 mm thick wall care putty on wall of newly plasterd surfaces of walls, pillars cornces etc. complete all as specified and directed.

Material and labour for applying 2 mm thick wall care putty to achieve even and smooth surfaces on NEW /old plasterd surfaces wall/ceiling and obtain using sand paper complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces of ceiling including pilasters, cornics etc and applying three coats of white wash complete all as specified and directed.

Material and labour for Prepration of old surfaces of walls, pillars, cornices etc. including scrapping down smoke, soot, and efflorescent salts and treatings oil and gresy spots, brooming down or steel wire brushing removing nails making good holes, cracks etc. on plastered or unplastered surfaces Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

Material and labour for Prepration of old surfaces of walls, pillars, cornices etc. including scrapping down smoke, soot, and efflorescent salts and treatings oil and gresy spots, brooming down or steel wire brushing removing nails making good holes, cracks etc. on plastered or unplastered surfaces and applying Two coats of oil bound distemper on wall (white or tinted) complete all as specified and directed.

Material and labour for Prepration of old surfaces of ceiling including scrapping down smoke, soot, and efflorescent salts and treatings oil and gresy spots, brooming down or steel wire brushing removing nails making good holes, cracks etc. on plastered or unplastered surfaces and applying one coats of white wash on ceiling surface complete all as specified and directed.

Supply only water proofing compound, ISI marked complete all as specified and directed.

Taking down chowkats or frame with shutters of any description (without taking off shutters from the frames) not exc. 1.5 Sqm each complete all as specified and directed.

Taking down chowkats or frame with shutters of any description (without taking off shutters from the frames) exc 1.5 Sqm but not. exc. 4 Sqm eachcomplete all as specified and directed.

Material and labour for 35 mm thick factory made solid (Wood polymer composite) moulded gauged door shutter with wire mesh in any number of division with brown wood grain texture, including double S.S wire mesh shall be fixed with 15 x 15 Square tubes in is rails with screwing 8 x 28 mm heat metal zink coated screws can be remove or fix again after changing of wire mesh when needed. The density shall be as per manufactures instructions complete all as specified and directed.

Material and labour for Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg/Cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Note : Stainless steel butt hinges and necessary S.S screws shall be paid separately.

Material and labour for Factory made single extruded WPC (Wood Polymer Composite) solid door frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/Cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant including making good after complete all as speicifed and directed.

Material and labour for Factory made single extruded WPC (Wood Polymer Composite) solid door frames/ Chowkhat of size 65 x 125 mmcomprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/Cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant including making good after complete all as speicifed and directed.

Taking down aluminium window/steel window & ventilator frame of any description not exc 1.5 Sqm each complete all as specified and directed.

Supply and fix anodised aluminium powder coated any colour minimum coating 50 micron three track windows/ventilators with one or more rebates including joining cleat for fixing etc complete with frame and shutter of fixing with handles, tower bolts, rubber gasket and maruti lock, and making good to disturbed surface with cement concrete 1:2:4 and cement mortar 1:4 complete all as specified and directed.

Supply and fixing of anodised aluminium powder coated window and ventilator shutters, sliding/side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary 5.00 mm thick sheet tinted glass quality & glazing, aluminium joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21 100mm long (2 no.) suitable handle (1 no.), rollers etc including taking down of old shutter and making good to disturbed surface with cement mortar in 1:4 complete all as specified all as specified.

Supply and fix stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple/ wooden beads complete all as specified and directed.

Supply and fix 100mm stainesless steel butt hinges, fixed, type B-21 complete all as specified and directed.

Supply and fix aluminum alloy anodised sliding door bolts with hasp & staple & fixing clips of sheet cast extruded section & fixing bolts & sliding bolts of extruded section 300 mm long complete all as specified and directed.

Supply and fixing of 300mm mild steel ordinary rat tail rod pattern spring incl roller plate complete all as specified and directed.

Supply and fix 150 mm long stainless steel tower bolts of fixied with both side nut and bolt complete all as specified and directed.

Supply and fix 150 mm stainless steel handles, both side nut and bolt fixed complete all as specified and directed.

Supply and fix floor door stopper 140 mm overall length of cover plate of aluminium alloy body and tongue, anodised. With hard drawn spring, fixed in floor complete all as specified and directed.

Supply and fix 100 mm long hasp & staple aluminium anodised wire type, incl bolt to hinge plate and fixed with screw complete all as specified and directed.

Supply and fix 100 mm dia extruded brass handle, fabricated type polished fixed to board complete all as specified and directed.

Supply and fixing of Sheet glass shelf assembly consisting of 5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified.

Supply and fixing of in repair chromium plated glass corner (Corse) size 300mm x 300mm complete all as specified and directed.

Supply and fix MS Peg set of six powder coated complete all as specified and directed.

Supply and fix in repair, 25 mm dia, 1 mm wall thickness stainless steel fancy type, decorative curtain rod with decorative ball type side brackets (As per Sample) fix with wooden gutties complete all as specified and directed.

Supply & laying of CPVC pipes 20 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors includind all necessary fittings and taking up or down steel tubing and connections for 15 mm bore of pipecomplete all as specified and directed.

Supply & laying of CPVC pipes 25 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors including all necessary fittings and taking up or down steel tubing and connections for 15 mm bore of pipecomplete all as specified and directed.

Supply & fix in repair, for 15mm bore fancy type central hole basin mixer with 135 mm extension body fixed spout without popup waste system with 350 mm long braided hoses of 15 degree flow angle complete all as specified and directed.

Supply & fix in repair, brass chromium plated single lever wall mixer 4-in-1 system with provision of both over head shower with 115 mm long bend pipe connecting legs and wall flange (wihout head shower) complete all as specified and directed.

Supply & fix in repair, 15 mm bore single lever Sink mixer complete all as specified and directed.

Supply & fix in repair, Vitreous China Wash Hand Basin, white, flat back, size 550 x 400 mm including brass coupling, mild steel brackets fixed to wall with pedestal etc. complete all as specified and directed.

Supply & fix in repair, Viterous China wash down water closet pan (pedestal pattern) coloured including 'P' or 'S' trap incl plastic seat cover white closed pattern with float bottom and cover and jet connection and mild steel chrominum plate or aluminized hanging device complete all as specified and directed.

Supply & fix in repair, 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe of low level of 32 mm dia fixed to wall complete all as specified and directed.

Supply and fix in repair, 8 mm dia brass, chromium plated health faucet (Hand shower) with 01 meter long flexible tube and wall hook complete all specified and directed.

Supply and fix in repair, PVC connection 15mm dia size and 450 mm long with 2 Nos check nuts its washers complete all as specified and as directed.

Supply and fix in repair, PVC Bath Cabinet made from hard thermosetting material with mirror, white/ivory colour, 400 x 500mm size complete all as specified and directed.

Supply and fix in repair, Bib tap 15 mm bore, fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

Supply and fixing of , in repairs, brass, chromium plated tubular towel rack 20mm dia 60cm long between flanges, 300mm vide with hooks complete all as specifed and directed.

Supply and fix in repair, angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe complete all as specified and directed.

Supply and fix in repair, CP two way angle valve with wall flanges 15 mm bore, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

Supply and fixing of in repair 15 bore dia chromium plated conceled Angle/stop cock screwed down high pressure with crutch or butterfly handle & screw both end for iron pipe or for unions complete all as specified and directed.

Supply and fix in repair, CP, soap dish holder complete all as specified and directed.

Supply and fix in repair, Soap Dispenser with glass bottle complete all as specified and directed.

Supply and fix in repair, tumbler holder complete all as specified and directed.

Supply and fix in repair, Towel ring round with round flange complete all as specified and directed.

Supply and fix in repair, sinks with drainage board made of stainless steel 1 mm thick kitchen with plugs, washers and wastes, & waste pipe incl bedding in cement mortar to dwarf wall or incl fixing suitable sizes of cantilever brackets and connecting union to pipe overall size 915 x 460 mm, bowl size 410 x 330 x 160 mm complete all as specified and directed.

Supply and fix in repair, 1 mm thick kitchen plate rack made of stainless steel 900 x 750 x 250mm size fixing with wooden plug with suitable size of screws complete all as specified and directed.

Supply and fix in repair, chromium plated overhead shower rose swivel type 200 mm with CP arms 400 mm long complete all as specified and directed

Supply and fix PVC (SWR) 'P ' trap for 110 mm dia etc. complete all as specified and directed.

Supply and fix in repair, chromium plated toilet paper holder with flap call complete all as specified and directed.

Material and labour for RCC as in kitchen platform, shelves & chajjas etc type B1 1:2:4 (20 mm graded aggregate) including necessary form work complete all as specified and directed.

Material and labour for 18-20 mm thick granite slab (of any type) work (table rubbed and polished) in cooking platforms, steps, window cills, incl edge moulding & cutting holes for gas pipe through drill machine and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks,etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories complete all as specified and directed.

Supply and fix PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

Supply and fix PVC (SWR) pipes 75 mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete all as specified and directed.

Supply and fix PVC (SWR) pipes 50mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete all as specified and directed.

Supply and fix clamp made out of 50 x 5 mm flat iron, 16mm dia round iron stays including bolts & nuts and securing ends of stays to wall or roof for 110mm PVC pipe complete all as specified and directed.

Supply and fix PVC (SWR) plain bend any radius for 75 mm bore complete all as specified and directed.

Supply and fix PVC (SWR) bends any radius provided with access door of 110 mm dia complete all as specified and directed.

Supply and fix PVC (SWR) plain bend T (Single T) equal or unequalany radius for 110mm bore complete all as specified and directed.

Supply and fix PVC (SWR) plain bend T (Single T) equal or unequalany radius for 75 mm bore complete all as specified and directed.

Supply and fix in repair, PVC (SWR) floor/ gully trap, square or round mounthed, any type of size 125 x 100 mm, setting and jointing with tting and jointing with solvent cement cement (1:1) complete all as specified and directed.

Supply and fix in repair, cockrach trap cum grating of size 100 mm x 100 mm complete all as specified and directed

Supply and fix PVC (SWR) branch pieces, single (equal or un equal), ordinary or inverted (spigot or socket type) or with parralled branches of 110 mm dia with access door complete all as specified and directed.

Supply and fix PVC (SWR) branch pieces, single (equal or un equal), ordinary or inverted (spigot or socket type) or with parralled branches of 75 mm dia with access door complete all as specified and directed.

Supply and fix PVC (SWR) vent cowl 110 mm bore complete all as specified and directed.

Supply and fix in repair PVC (SWR) nahani/ floor trap, plain with grating with or without waste hole including jointing with solvent cement 75mm dia etc complete all as specified and directed.

Dismantling water tanks of capacity exc 250 and not exc 500 Ltrs complete all as specified and directed.

Supply and fix 500 ltr capacity rotational moulded polyetheylene water storage tanks (cylingrical verticlal with closed top) hoisted and fixed in position all as per SSR part-I complete all as specified and directed.

Supply and fix in repair Ball valves 20 mm dia high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms) complete all as specified and directed.

Supply and fix in repair Gun metal, globe or gate valve with iron wheel head, 20 mm bore, screwed both ends for iron pipe including adaptor to join the pipe complete all as specified and directed.

Material and labour for plain cement concrete (1:5:10) type D-2 using 40 mm graded stone aggregate as in filling in sunken floors including demolition of cement in concrete (unreinforced) of any description and in any position in ground floor and pavings any thickness (below or above ground level) complete all as specified and directed.

Material and labour for for Water proofing treatment to sunken floors of kitchen, toilets, laboratories, bath and WC's etc shall be as under :- (i) Application of Two component Acrylic modified Cementitious coating (a) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or milling to remove cement laitance, existing coatings and achieve a gripping profile that is clean, dry and free from laitance and any other form of surface contamination. The installation instructions in manufacturer’s published literature should be strictly complied with, including but not limited to the following :- (b) Chipping out any visible cracks in “V-Groove” pattern as applicable. Special attention on this part. Cleaning of cracks & then filling those cracks with SIKA latex SBR 100 putty/ Dr Fixit 302 SBR latex / Perma latex SBR / FOSROC Nitabond SBR latex / Asian Paints latex as required. Final cleaning of surface with power grinder, wire brush, hair brush & vacuum pressure if required. (c) Dampen all surfaces immediately ahead of application of Acrylic modified Cementitious coating of Sika Top Seal – 107 / Brush Bond FOSROC/ Dr Fixit/ STP/CICO. (d) Whilst the surface is still damp from saturation (S.S.D), apply one coat of Acrylic modified Cementitious coating of Sika Top Seal – 107 / Brush Bond FOSROC/ Dr Fixit/ STP/CICO of viscosity as per manufacturer’s instructions.

(e) Apply Glass Fabric Sheet of Sika Fab 1 / FOSROC/ Dr Fixit/ STP whilst the first coat is wet. (f) Once touch dry, apply second coat of Acrylic modified Cementitious coating of Sika Top Seal – 107 / Brush Bond FOSROC/ Dr Fixit/ STP/CICO of viscosity as per manufacturer’s instructions on the entire area. (g) Second coat shall be applied after 6-8 Hrs of application of previous coat and in the direction right angle to the previous coat. (h) The waterproofing coating should be taken to a height minimum 300 mm above the finished floor level on the vertical surface. (j) It is essential to cure Acrylic modified Cementitious coating immediately after application (minimum 6-8 Hrs drying) for a minimum of 3 to 5 days to ensure full cement hydration and to minimize cracking.

(k) A protection plaster (12-15mm thick) in CM 1:3 admixed with appropriate Integral water proofing compound has to be applied on the walls. Admixture : Sika Plastocrete Plus / FOSROC / Dr Fixit / STP / CICO confirming to IS 2645. Providing and applying a protection screed of 50mm thick 1:4, cement sand mortar admixed with Sika Plastocrete over the applied water proofing coating on horizontal surfaces. Admixture : Sika Plastocrete Plus / FOSROC / Dr Fixit / STP / CICO confirming to IS 2645 (ll) All the corners and joints should be pretreated with an elastic waterproofing sealing tape with a Woven bonding mesh on each surface and an elastic expansions zone in the centre of Make Sika Seal Tape S/FOSROC/Dr Fixit/STP. (m) The membrane has to be protected in accordance with the manufacturer’s recommendations until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accordance with manufacturer’s recommendations (n) Waterproofing treatment has to be carried out through applicators authorised (ii) All the joints of pipes and traps within the sunken portion shall be sealed properly by epoxy sealant. (iii) Al CI traps in sunken slabs to be enclosed with PCC 1:1.5:3 (min 15cm) All -round. (iv) The sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40mm stone aggregate) complete all as specified and directed.

(v) Providing drainage spout pipe GI 40 mm dia bore light grade upto outside of outer wall (Approx 450 mm to 600 mm long) including cutting to existing wall and making good the disturbed surface complete all as specified and directed. (vi) Providing 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in flooring for laying floor finish all as specified. Note: Items Number in note (iv), (v) & ( vi) above shall be measusred and paid speready.

Supply and fixing of drainage spout pipe GI 40 mm dia bore light grade upto outside of outer wall (Approx 450 mm to 600 mm long) including cutting to existing wall and making good the disturbed surface complete all as specified and directed.

Material and labour for, for moulded machine pressed precast concrete paver block rubber moulded with colour Yellow , Black and Red only glossy finished with with laquar and size conforming to IS 15658- 2006 of 60mm thickness, M-35 grade including 25mm thick sand cushion below paver blocks complete all as specified and directed.

Dismantling boarding any description fixed in any position with nailsv complete all as specified and directed.

Supply & fix 20 mm thick, PVC sheet one side prelaminated of approved texture ("Celuca ply of Rajshree make or equivalent as in Kitchen cabinet, cub board (with shelves and partitions) including necessary fitting & fixture as per manuacturer's instructions complete all as specified and directed.

Dismantling brick tiles or terrcing single layer as in roofing complete all as specified and directed.

Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and directed.

Material and labour for 50 mm avarage thickness PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as roof padding, haunching, sub base floor complete all as specified and directed.

Material and labour for preparation of roof surface & applying evenly a tack coat of industrial bitumen primer 85/25 grade @ 1.6 Kg/Sqm including APP based polymeric membrane minimum weighting 3 Kg/Sqm and minimum 3 mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/sqm) land on primed surface by forced application, joints to be touched hot and width of overlaps not be less than 150 mm complete all as specified and directed.

Material and labour 40 mm thick brick tiles laid and joints in cement mortar (1:3) over 15 mm thick screed bed in cement morter 1:6 and flush pointing as work proceed complete all as specified and directed.

Material and labour 40 mm thick brick tiles laid and joints in cement mortar (1:3) over 15 mm thick screed bed in cement morter 1:6 and flush pointing as work proceed but EXCEPT TILES complete all as specified and directed. Note:- Useable Tiles received from dismantling to be reused after cleaning etc.

Material and labour for damproofing to wall with two component Acrylic polymer cementitious water proof elastomeric coating foor grade mix to form uniform slurry and apply with paint brush as first coat then laying a layer of fibre glass mesh cloth as first coat is still green with overlap of joints of fibre mesh not less than 100 mm, then finally apply second layer mix by brush to entire surface of container covering 0.6 - 0.75 Sqm /Kg at 1 mm thickness in two coat depending on the level of substrate and curing it for minimum 3 days complete all as specified and directed. Note : Quoted rate shall be deemed to be inclusive of materials all labours, tools and plants, scaffolding and working upto height 6 metre etc.

Material and labour for cement concrete (1:2:4), type B0, using 12.5 graded stone aggregate in roof kerbs coving roof kerbs coving coved fillets of 75mm radius at junction bof roof slab and parapet wall, vertical surfaces and like etc complete all as specified and directed.

Cutting chases, pinning in brick walls /stone concrete block or slab walls, making good to facings where required using expended metal in required size & pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc; & cutting chases for concealed water tubing or concealed conduit wiring, etc.& making good, cutting not exc 10 cm but not exceeded 20 cm grith complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth for foundation etc or for shafts, wells cesspits manholes pier holes etc not exceeding 10 sqm on plan and not exceeding 1.5m depth in soft/loose soil etc complete all as specified and directed.

Returning, filing in, excavated soil including spreading, levelling, watering and well ramming in layers not exceeding 25cm etc complete all as specified and directed.

Removal of excavated materials not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting points etc complete all as specified and directed.

Material and labour for laying DWCP 150 mm dia pipes in trenches Class SN-8 conforming to IS 16098 (Part -2) in 6 mtr length with coupler including Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete ) set in cement mortor for 150 mm internal dia of pipe complete all as specified and directed.

Material and labour for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete all as specified and directed.

Material and labour for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished ,and reforming benching as required for 150 mm internal dia of pipe complete all as specified and directed.

Supply and fix ornamental stainless steel tubular pipes/sheets, pieces such as pipe caps globe at top 18 guage and grade 304 as in staircase railing including welding, moulding riveting nut and bolt with all necessary fittings complete all as specified and directed.

Supply and fix framed work as in doors or gates of angle or other section with gusset plates, rails, braces staircase etc. complete drilled for fixing of steel gate sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, runing rails and guides) and hanging also fastning and fixing confirming to FE-290 (Gde E-165) complete all as specified and directed.

Supply and fixing of mild stel framed work such as gurad bars/grills, grating etc with end of shouldered and/or riveted or forged into spikes and similar owrks including one shop coat of zinc chromate primer complete all as specified and directed.

Material and labour for Preparation of newly steel surface of any description over 10 cm width or grith and applying two coats of synthetic enamel paint complete all as specified and directed.

Material and labour for RCC 1:1.5:3, type A1, using 20mm graded stone aggregate as in suspended slabs supported on walls/columns, in floors, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Material and labour for form work to soffit of suspended slabs such as roof slabs, floor slabs, landings and simillar works not exceeding 20cm thick and rough finished surfaces of complete all as specified and directed.

Supply and fix Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including ,cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Removing building materials upto to a distance of 1.00 KM to 2.5KM or under, including loading, unloading and stacking at the destination complete all as specified and directed.

Taking down aluminium/copper point wiring from existing conduit / batten (light, fan, socket or power) complete such as switches, ceiling rose, pendent, regulators, socket, light fittings etc and removing material from site and making good the disturbed surface of wall / floor etc, complete all as specified and directed

Material and labour for for Point wiring in replacement with 1.5 Sqmm (Nominal Area) 1100 Volt Insulated, FRLS unsheathed multi stranded flexible copper conductor cable in NEW PVC concealed conduit not less than 20 mm dia 1.5 mm thick for one light / fan point controlled by one switch (including cutting chases and making good the distributed surface ) and fixing new 3 mm thick hylem sheet top cover, sheet screws and 1.6 mm thick GI sunken boxes included 1.5 sqmm stranded copper conductor with green PVC insulation earth contunity conductor connected to comman earth dolly etc. for One light / bell piont/ Fan point/ Exhaust fan point controlled by one 5 Amp switch one way completecomplete all as specified and directed for the following:- NOTE : The cost of sunken boxes and bakelite sheet is included in the quoted rate)

All as per Srl item No 130 above but on the Indepedant board complete all as specified and directed.

All as per Srl item No 130 above but one 3 pin socet on the same board complete all as specified and directed.

All a per item No 130 above but with 2.5 Sq mm size cable multi stranded FRLS copper wire unsheathed for one 3 pin socket outlet 15 Amps on independent board including continuous earth wire of PVC insulated 2.5 Sq mm size cable multi stranded FRLS copper wire connecting to common earth dolly complete all as specified and directed.

Supply and fixing in replacement switch piano type 6 Amps one way 230 volts 50 hz AC complete all as specified and as directed.

Supply and Fixing in replacement socket outlet 5 pin, 6 Amps flush type 230 volts 50 Hz AC complete all as specified and as directed

Supply and Fixing in replacement switch piano 16 Amps type one way 230 volts 50 Hz AC complete all as specified and as directed

Supply and Fixing in replacement socket outlet 6 pin 6/16 Amps multi purpose flush type 230 volts 50 Hz AC complete all as specified and as directed

Supply and Fixing in replacement switch type regulator 5 step 230 volts 100 Watt AC complete all as specified and as directed

Supply and fixing in replacement ceiling rose 65/50 mm two to three terminals complete all as specified.

Supply and fix in replacement MCB 40 Amps single pole with neutral, (SPN) AC 230 Volts 50 Hz complete all As specified and directed.

Supply and fix in replacement MCBs single pole (SP) 5 to 32 Amps with 10 KA breaking capacity of 'B' series in distribution boards complete all as specified and directed.

Supply and fixing in replacement Sheet metal enclosure for DB's when MCB's to be used Double door factory made flush fixed complete with 200 Amps rated busbar 240 Volts single phase 8 ways complete all as specified

Supply and fix in replacement for sub main wiring with two run of single core (FRLS) PVC insulated and unsheathed cable with copper conductor (Multi strand) having nominal area 6.0 Sqmm drawing into and including PVC non metallic rigid conduit medium grade of adequate size and making electric connections including one run (FRLS) PVC insulated single core copper conductor cable 6.0 Sqmm as a earth continuity conductor(green colour) and including non metallic medium grade rigid PVC conduit, including cutting chases in brick wall, and making good to match the existing specifications complete all as specified and directed by Engineer-in-Charge. Note :- (i) Rates are deemed to be included cutting and making holes in wall/floor for passing in or through conduit (ii) Two run of 6.00 sqmm single core (FRLS) PVC insulated copper conductor cable, one run of 6.0 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of suitable size will be measured as a one unit.

Supply and fix in replacement for sub main wiring with two run of single core (FRLS) PVC insulated and unsheathed cable with copper conductor (Multi strand) having nominal area 4.0 Sqmm drawing into and including PVC non metallic rigid conduit medium grade of adequate size and making electric connections including one run (FRLS) PVC insulated single core copper conductor cable 4.0 Sqmm as a earth continuity conductor(green colour) and including non metallic medium grade rigid PVC conduit, including cutting chases in brick wall, and making good to match the existing specifications complete all as specified and directed by Engineer-in-Charge. Note :- (i) Rates are deemed to be included cutting and making holes in wall/floor for passing in or through conduit (ii) Two run of 4.00 sqmm single core (FRLS) PVC insulated copper conductor cable, one run of 4.0 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of suitable size will be measured as a one unit.

Material and labour for replacement of lamp holder insulated body with 9 Watt LED Bulb, back plate batten/angle type for batten fitting fixed on bakelite sheet 100mmx100mm 230V AC cool day light 6500K having maximum height 1020mm heavy duty complete all as specified and directed.

Supply and fixing in replacement of sheet steel enclouser distribution boards, double door factory made TPN Vertical 4 way 3 phase 415 volts 4 way with 200 amps rating copper bus bar and PVC insulated copper jumpers of suitable size from the MCCB to the out going circuits one incoming MCCB and 12 outgoing MCBs circuits comprising of 3 phase 4 wire of suitable rating complete all as spcd and directed with the following accessories :- (a) MCCB 100 amps, 16 KA, 4P, 415 volts, 50 Hz = 01 No. (Note:- Out going MCB shall be measured and paid for separately)

Supply and fixing in replacement of LED T-8 tube light fitting with sinle side connection LED tube rod 18/20 W, 4 Feet made of CRCA sheet steel box type including bipin holder and connection with PVC insulated three core 23/0.0076 twisted copper cable from ceiling rode to light fitting complete all as specified and directed.

Supply & fix LED Street Light Luminaire 25 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens complete all as specified and directed.

Supply and fixing of security light mounting bracket made out of GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat of size 40 x 6 mm and nuts and bolts and painting with aluminium paint,complete all as specified and directed.

Supply, laying in trenches or wall and testing in replacement of cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (Heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sqmm 4 core all as specified and as directed.

Material and labour for for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 15 mm bore( light grade) and watering pipe 20 mm bore GI pipe (light grade ) and chamber of pcc 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 5 of SSR PART 1 , with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switche, DBs) complete all as specified & testing on completion.

Supply,laying & fixing in replacement double wall corrugated (DWC) pipes made of high density polythyline (HDPE) with all accessories i.e. all type of joints,Sockets,Elbows,bends and End caps etc.. all as specified and directed by Engr in Charge of size 63mm outer dia and 50 mm inner dia complete all as specified and directed.

Taking down ceiling fan/geyser/exhaust fan in situ and refixing after servicing, repairing and painting to ceiling fan scrating old paint and preparation of surface for painting with one coat of white / grey enmeled paint and including cable from ceiling rose to fan complete all as specified and as directed.

Supply and fixing of in replacement of single pole and neutral sheet metal enclosures with two pin & earth plug and socket complete with one single pole MCB of 20 amps complete all as specified and as directed.

Supply and fixing in replacement of bell push 6 amps one way 230 volts 50 Hz AC complete all as specified and as directed.

Supply and fixing in replacement of bell ding dong AC 230 volts 50 Hz complete all as specified and as directed.

Supply and fix exhaust fan, steel body single phase 230V of size 300 mm sweep with blades, frame and louvers all as specified and directed.

Supply and fixing BLDC (Brushless direct current motor) ceiling fan 1200mm sweep copper winding low power consumption,high speed Aliminium body with blade, double ball bearing having minimum air delivery 220 CMM and BEE 5 star rated including .acessories,connector,down rod etccomplete all as specified and directed.

Supply and Fix Storage water heater (Geyser) of 25 litre capacity 230V AC, 50HZ having element of 2 KW of COPPER/INCOLOY alloy , Rust proof outer body,high density PUF insulation, BEE 5 Star Rated ,Inner tank of SS 304 which can sustain pressure of minimum 7 Bar working pressure and having multifunction safety valve plug top , making electric and water connection complete all as specified and directed.

Supply and fixing in replacement pvc connection of size 600 mm length 15 mm dia complete all as specified and directed.

Supply and fixing of in replacement of LED bulkhead light fittings 10 watt white including LED strip as per IP 65 in engineering plastic housing with clear primatic diffuser and making necessary connection complete all as specified and directed.

Material and Labour along the external wall below concrete or masonry around using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

Material and Labour for applying finishing walls with Acrylic smooth exterior paint of required shade : New surface work (Two coats applied @ 1.67 Ltr/10 Sqm each coat) over and including priming coat of exterior primer applied @ 2.20 Kg/10 sqm complete all as specified and directed.

GEE EMM ASSOCIATES (BID ID -3508556)

M/s Vijay Construction Co. (BID ID -3508758)

tarlok singh contractor (BID ID -3508750)

Santokh Singh and Associates (BID ID -3502798)

M/s MAHAJAN CONSTRUCTION CO. (BID ID -3508488)