REPAIRS TO ROOF, FLOORING, FOOTPATH AND HARDSTANDING AND FENCING IN AOP AREA UNDER GE NASIK ROAD CAMP.

Amount

Dismantling Asbestos cement (corrugated,semi corrugated etc) sheets in roof coverings complete all as specified and as directed.

Dismentling of Single layer Mangalore pattern or similar tiles in roofing

Dismentaling of Plain or corrugated steel sheeting, any gauge, thickness, includingm Nainital or similar pattern roof coverings

Dismantling wrought iron or mild steel work of any description not otherwise provided for

Dismantling timber scantlings 40 sq. cm and over in section, in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section

Dismantling boarding, any description, fixed in any position with nails

S&F ERW or Induction butt weld M.S. Square tubes black in purlins and rafters conforming to IS 1161-1979 grade Yst 250 including fabrication & erection fixing complete

S&F Steel work in tubular trusses inclunding special shaped washer etc.complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St-240.

S&F Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc.Fe410W(GdeE-250 qualityA) including fabrication & erection fixing only

S&F framed work as in plates (plain or chequred) channels, square cut or notched with fabriction and erection of FE 410-W (Gde E-250) auality A (ordinary and counter sunk) forming holes without any attachment

S&F 12mm Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long

S&F 12mm Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm n exc 10cm long

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall,fixed with self tapping scews as specified.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall,fixed with self tapping scews as specified.

S&F 2mm thick Fibre glass reinforced translucent reinforced corrugated sheeting with two corrugations side lap fixed with coach screw and washers in roof wall etc complete all as specified and as directed.

S&F 2mm thick plain Polycarbonate Sheet with including all necessary fixtures and fastenings

S&F 6mm thick multilayer Polycarbonate Sheet in roof or wall cladding fixed with aluminium clutch/tee EPDM gasket and self tapping screws with including all necessary fixtures and fastenings

Dismantling wall ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/blalnkets, including cover fillets, GI/aluminium gridetc.

M&L for GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length ) of 0.55 mm thickness having kurled web of 50mm and fllange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre.

M&L for 6mm and thick PVC multiwall 250mm wide (tongue and groove interlocking type) panels, textured on one side (as approved): fixed to framework in ceiling with countersunk screws and inerlocked, including all necessary special fitting accessories such as junction, corner and turning matching to board. (GI framework to be measured and paid separately)

M&L for 8mm thick and PVC multiwall 250mm wide (tongue and groove interlocking type) panels wall lining and fixing at site on PVC frame as per specifications.

Demolition of concrete in any description and in any position.

M&L for Providing cement concrete type D2 1:4:8 (40 mm graded aggregate) in foundations, filling and mass concrete

Demolition of concrete in ground floors and pavings n exc 15cm thickness (below or above ground level).

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for 100 mm thick sub-base with cement concrete type D-2, 1:4:8 (40mm graded aggregate).

M&L for 75 mm thick concrete flooring with cement concrete type B-2, 1:3:6 (40mm graded aggregate).

M&L for Vitrified Ceramic tiles (Superior quality) 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick cement mortar screed bed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in coloured cement to match.

M&L for Vitrified Ceramic tiles (Superior quality) 10 mm thick (square/ rectangular) polished in skirting etc. cut out of tiles of area not exceeding 0.36 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick cement mortar rendering in cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match.

M&L for 100 mm thick concrete flooring with cement concrete type B-2, 1:2:4 (40mm graded aggregate).

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

M&L for One coat of Floor guard paint on paved surfaces including preparing by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots; making good holes, cracks etc.

M&L for Two coat of Floor guard paint on paved surfaces including preparing by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots; making good holes, cracks etc.

M&L for Chequered cement concrete tiles with grey cement and pigment 40cm x 40cm x 25mm thick, with rubber moulded glossy finished surface, laid in floors over and including 15mm thick cement mortar screed bed in cement mortar 1:6, set jointed and pointed in neat cement slurry in floors.

M&L for Preparing new or untreated brick, stone, concrete, asbestos cement or plaster surfaces of any description over 10cm girth or width, not otherwise described and two coats of synthetic enamel paint over and including priming coat.

S&F Stainless steel (grade 316) work in railings, grills, balusters including necessary fittings and decorative articles such as base plates, flanges, caps, knobs, studs, spikes,chain etc. and stainless steel welding and fastening in position.

M&L for removing SS poles of any description embedded in concrete, removing damaged concrete base and casting the same in PCC 1:2:4 type B-1 concrete of size 30cm X 30cm X 30cm, and erecting back in soil of any type including necessary excavation and making good disturbed ground complete all as specified and as directed.

M&L for Preperation of new untreated steel or iron surfaces of any description over 10cm girth or width, not otherwise described and two coats of synthetic enemel paint over a coat of red oxide, zinc chrome primer.

Dismantling of stone/boulder masonry, laid dry in pitching.

M&L for stone/ boulder pitching, hand packed tightly and grouted with cement and sand mortar 1:6 including raised pointed in cement mortar 1:4 (including dressing and levelling the surface).

- Ditto - As per Item No. 41.00 but except stone/ boulders.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc.

M&L for Brickwork with flyash bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 using old size bricks.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L for Rendering 15mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces finished even and smooth without using extra cement.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

Dismantling barbed wire fixed to any type of standard rails straining bolts (each line wire to be measured).

Dismantling RCC posts or struts any section, embedded in concrete, brick work, masonry etc. including taking out embedded portion and making good disturbed ground.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth round, in layers not exceeding 25 cm in soft/loose soil.

M&L for Providing cement concrete 1:4:8 type D2 (40 mm graded aggregate) in foundations, filling and mass concrete including sub bases of flooring and pavings.

S&F mild steel Posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165.

M&L for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm but n exc 10cm and diameter of neck 5 to 10 mm.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire.

Supply only chain link MS galvanised fencing, any size or type.

S & F 4mm dia plain mild steel wire, galvanised class 3 in fencing including straining and fixing to concrete or steel posts and/or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. as directed (each line of wire to be measured).

M&L for Preparation of new or previously untreated steel or iron surfaces of any description not exc. 10cm width or girth and two coats of aluminium paint over a coat of red oxide primer.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar.

M&L for Rough Shahabad stone 25mm to 30mm thick in flooring/plinth set and jointed in in neat cement slurry and pointed in CM 1:4 complete all as specified and directed over and including 15mm thick screed bed in cement mortar 1:6.

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS. 49260.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

Vinod Enterprises

Rehoboth Buildcon

M/S K. K. Construction

Alpha Construction

SVT ENGINEERS AND CONTRACTOR.

Bidder Name

SVT ENGINEERS AND CONTRACTOR.

M/S K. K. Construction

Alpha Construction

Vinod Enterprises

Abhiraj Enterprises

Rehoboth Buildcon