REPAIR TO KOTA FLOORING, PLINTH PROTECTION, GUNNITING AND CERTAIN

Amount

Demolition of brick work or stone/boulder masonry built in cement mortar complete all as specified and directed by Engr In Charge.

M&L for brick work with subclass 'B' bricks, straight or curved on plan exc 6 M mean radius built in CM 1:6 complete all as specified and directed by Engr In Charge.

M&L Brickwork with sub- class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed by Engr In Charge.

M&L for rendering CM (1:6) 10 mm thick on other than fair faces of brick work or concrete surfaces etc including finished even and smooth without using extra cement up to four storey height bldg complete all as specified and directed by Engr In Charge.

M&L rendering 15mm thick in cement mortar 1:4 on other than fair faces of brick work or concrete surfaces finished even and smooth with using extra cement complete all as specified and directed by Engr In Charge.

M & L rendering 5mm thick on ceiling in cement mortar 1:3 finished fair and even smooth without using extra cement complete all as specified and directed by Engr In Charge.

Taking down cement or cement lime plaster on brick walls incl racking out joints hacking for key scrubbing down with water etc and removing the debries outside the MOD land complete all as specified and as directed by Engr -in - Charge.

M&L for preparation of new surface and applying two coat of distemper on wall/ceiling over with 3mm thick elastomeric wall care putty on walls complete all as specified and directed.

M&L for prepration of old plastered or unplastered surfaces of walls and applying two coat of approved shade of oil emulsion distemper with 3mm thick elastomeric wall care putty on walls, including repairing of pot holes and cracks with putty, take it plaster where it required complete all as specified and directed by Engr-in-Charge.

M&L for preparing surfaces of new plaster on walls and applying exterior two or more coats of APEX/WEATHER over 3mm putty including priming coat of exterior primer applied complete all as specified and directed by Engr-in-Charge.

Material & Labour for prepration of old plastered or unplastered surfaces of walls and applying exterior two or more coats of APEX/WEATHER over 3mm putty including priming coat of exterior primer applied complete all as specified and directed by Engr-in-Charge.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) area not exc 1.5 sqm (including make good with CM 1:4 and hold fast) complete all as specified and directed by Engr In Charge.

S&F windows/ventilators section of frame 72 X 55 fixed to wall or concrete surface with ms hold fast (30 x 5 section) 150 mm long made of galvanized steel powder coated and section of shutter 47 X 20 mm mulion section 72 X 50 mm (Base steel as per IS 513 "D" quality galvanozed as per IS 277 with zinc of 120 gms/ Sqm ) glazed or guaged and wire guage shutter prepare to recieve wire mess to the shutters ( Double door shutter) with total coated thickness of 0.60 mm including powder coated grill/guard bars made of surface bars 10 mm dia at 100 c/c horizontal spacing fixed in ms flat frame ( 30 x 5 mm ) fixed to windwods frames with screws incl 4 to 5 mm thick sheet glass, 0.36 mm stainless steel wire cloth with 1.40 mm aparture neccessary fittings and all builders hard ware such as handles ,tower bolts, and stays and cooler opening shall be provided with double side shutter with grill and desien of window shall be approved by Engr-in-Charge etc. complete all as specified and shown in Drg No : CEAF/STD-191/2014 Sheet No 1/2 and 2/2 dated 11-12-2014 .

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with printed sheet PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification complete all as specified and directed by Engr In Charge.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face complete all as specified and directed by Engr In Charge.

S&F 150mm long Aluminium anodised, barrel tower bolts of ex- truded section and fixed complete and specified and directed by engr-in -charge.

S&F 150mm long aluminium handle cast type polished bright complete and specified and directed by engr-in -charge.

S&F 100 mm long butt hinges medium weight, stenless steel, and fixed complete and specified and directed by engr-in -charge.

Dismantling stone slab and granite of any description or thickness in floors etc and removing the debries outside the MOD land complete all as specified and directed by Engineer-in-Charge.

M & L 15 mm thick screed bed or bedding layer of cement mortar (1:4), for laying of granite complete all as specified and directed by Engr In Charge.

M&L pure black Granite (of any type) tiles 20mm (+-2mm) thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including moulded ofnedges grinding and polishing complete all as specified and directed by Engr-in-Charge.

M&L green Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade to match the shade of marble stone including moulded ofnedges grinding and polishing complete all as specified and directed by Engr-in-Charge.

S&F in repairs stainless plate rack of size 900mmx750mmx250mm depth size made out of 0.75mm thick sheet complete all as specified and directed by Engr In Charge.

Dismantling/demolition floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises including scrap trown out of MoD Land complete all as specified and directed.complete all as specified and directed by Engr In Charge.

M&L Glazed ceramic coloured tiles in vertical surface 300X 450X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match incl back plaster 10 mm thick in cm 1:4 complete all as specified and directed by Engr In Charge.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not xceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed by Engr In Charge.

Ditto as above item No-26 but as on vertical surface of wall such as skirting incl 10mm thick cement plaster (1:4) as in backing coat of tiles complete all as specified and directed by Engr In Charge.

M&L Virified Ceramic light shade tiles 9 to 10 mm thick (square/ rectangular) polished, area of each tiles exc 0.36 but not exceeding 0.72 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match flooring( in any pattern) and jointed with neat cement slurry over 15 mm thick cement screed in CM 1:6 and pointed with coloured cement matching with surfaces of tiles as in floor including dismentling complete all as specified and as directed by Engr-In-Charge.

M&L Virified Ceramic light shade tiles 9 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match flooring( in any pattern) and jointed with neat cement slurry over 15 mm thick cement screed in CM 1:6 and pointed with coloured cement matching with surfaces of tiles as in floor including dismentling complete all as specified and as directed by Engr-In-Charge.

M&L for Chequered cement concrete tiles (rubber moulded with gloshy finishing) with grey cemet and pigments 30cm x30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with 15mm thick bedding layer of cement sand mortar (1:6) including 100mm thik cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub base for floors finishes including dismentling complete all as specified and directed by Engr In Charge.

S&F precast machine pressed PCC interlocking paver block of 80 mm thickness, M-40 grade of any shape and size confirming to IS -15658-2006 with grey cement and pigment as approved and 100mm thick plain cement concrete, type D-2, 1:4:8, (using 40mm graded stone aggregate) as in sub base flooring, surface finished even and rough to receive floor topping including sand cusion and dismentling complete all as specified and directed by Engineer-in-Charge.

M&L Machine pre polished cut kota stone slab 20 mm(+-2mm) thick in tread of steps, and similar over cement screed 20 mm thick in cm 1;4 base laid and jointed with grey slurry mixed with pigment to match the slab including rubbing 0ver CM 1:4:8 PCC 40MM thick and polishing as per and dismentling complete all as specified and directed by Engr In Charge.

.-Ditto-.but riser on stair case, skirting on walls etc incl the surface with . jointed with grey slurry mixed with pigment to match the slab including rubbing and polishing as per complete all as specified and directed by Engr In Charge.

S&F Rotational moulded polyethylene 1000 Ltr water storage tanks as per IS (cylindrical vertical with closed top) hoisted and fixed in position including necessary fittings with 20 mm dia Ball brass valves, high pressure, with polythene float and flynut including dismantling water tanks exc 500 but not exc 1000 ltrs capasity and removing to store complete all as specified and directed by Engr In Charge.

S&F in repair vitreous china squatting pan “orrisa” pattern of size 580mmx440mm “white” with integral foot rest (excluding flushing cistern and flush pipe) incl provision of cement concrete bedding, ‘P’ trap 100mm dia connection to trap , anti-syphonage complete all as specified and directed by Engineer-in-charge.

Supplying and fixing in repair for vitreous china wash down water closet pan, white (pedestal pattern), including plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, excluding fixing bolts, flushing cistern and flush pipe) complete all as specified.

S&F in repair PVC SWR floor trap with grating including jointing with solvent cement 75 mm dia complete all as specified and directed by Engr In Charge.

S&F in repairs10 ltr capacity PVC flushing cistern coloured with accessories Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete and specified and directed by engr-in -charge.

M & L for 75 mm thick PCC 1:3:6 type C2 as in Plinth Protection using 40 mm stone aggregate including making joints & filling with sand bitumen mastic as per incliding dismentling complete all as specified and directed by Engr In Charge.

S&F Aluminium(extruded section body) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as directed and specified.

S&F brass body Mortice lock, vertical type,size 100 mm 4 lever, incl escutcheon plate and two No keys fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair for 15mm bore steel water tubing medium grade , galvanized ISI marked with all fittings fixed to wall & ceiling or laid in floors including dismentling complete all as specified and directed by Engineer-in-charge.

All as per item bove but 20mm bore

Taking down rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed by Engr In Charge.

S&F for 75 mm dia pvc pipe Stack clamps out of 50 mm by 5mm flat iron and 16mm dia round iron stays,enlcuding bolts and nuts and securing ends of stays to wall or roof as percomplete all as complete all as specified and directed by Engr In Charge.

S&F for 110 mm dia pvc pipe Stack clamps out of 50 mm by 5mm flat iron and 16mm dia round iron stays,enlcuding bolts and nuts and securing ends of stays to wall or roof as per complete all as specified and directed by Engr In Charge.

S&F for PVC SWR bends 110 mm complete all as specified and directed by Engr In Charge.

S&F PVC SWR bends 75 mm complete all as specified and directed by Engr In Charge.

S&F for PVC (SWR) pipes 110 mm single socketed, in any length with solvent cement joints fixed to walls/laid in floors incl stack clamps of stainless steel with bolts & nuts etc complete all as specified and directed by Engr In Charge.

.-ditto-. But 75 mm dia..

S&F for PVC SWR Junction piece 75 mm provided with access door equal or unequal complete all as specified and directed by Engr In Charge.

S&F for 110 mm PVC SWR Junction single (Single T) provided with access door complete all as specified and directed by Engr In Charge.

M&L for guiniting work to RCC work in coloumn, chajjas, balconies, slabs, landings etc by removing loose, concrete, incl removing rust with short blasting and cleaning of surface with wire brush and applying epoxy treatment to rusted reinforcement and including S&F welded wire mess fabric or wire not less than 95x95x3mm adhesive plaster grade for concrete admixture and providing guniting pressure 2.00/2.50 Kg/Sq cm with admixture 1 part of cement and 3.50 part of sand and thickness 50mm average and making the surface even and smooth including necessary formwork and 10mm thick with CM 1:4 plaster over repaired surface with WPC complete all as specified and directed by Engr-in-Charge.

M&L for preparing surfaces of plaster on walls and applying two or more coats of plastic emulition paint over 3mm putty including priming coat of primer applied complete all as specified and directed by Engr-in-Charge.

Taking down carefully copper/aluminium point wiring( light ,fan, socket or power) complete, fitting such as switches, ceiling roses, pendents, regulators, sockets etc.removing materials to store for keeping in safe costudy or for taking credit (credit for above items should be made as per conditioned separately) and making good disturbed surface of walls, floors etc. Complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring with single core of FRLS PVC insulated unsheathed ISI marked 1100 V grade cable multi stranded copper conductor of size 1.5 sqmm drawing through in and including PVC conduit size of not less than 20 mm including conduit fittings and accessories concealed in wall / ceiling wiring on ceiling /wall terminated in flush metal box alongwith outer cover plate for mounting modular/piano switch, socket and electronic regulator along with provn of earth wire of PVC insulated, unseathed, 1100 V grade cable multi stranded FRLS ISI marked copper conductor of size 1.5 sqmm all as specified and directed by Engr-in-Charge. For One light point controlled by one switch one way.

All as per srl item 57 above but for one ceiling fan / Exhaust fan point controlled by one switch regulator.

All as per item No 57 above but for one 3 pin 5 amps socket outlet on indipendent board with other switchs.

All as per item No 57 above but for one 3 pin 5 amps socket outlet on the same board with other switchs.

All as per item No 57 above but for Call bell controled by one push button in indipendent board .

All as per item No 57 above but with 2.5 Sq mm cable for Independent one 3 pin 15 Amps socket outlet In and including S/C 2.5 Sq mm PVC insulated copper conductor unsheathed 1100 v grade IS -694 FR cable for continuous earth wire.

M&L for point wiring for one light fitting / one fan point controled by one switch with 1.5 Sq mm PVC insulated copper conductor cable drawing in and including PVC Casing/capping or surface conduit with 1.5 Sq mm PVC insulated copper conductor cable for continuous earth wire connected to main earth dolly with 3mm thick plastic laminated sheet cover complete for one light point controlled by one switch complete all as specified and directed by Engineer in Charge.

All as per srl item 63 above but for one fan point controlled by one switch through regulator.

All as per srl item 63 above but for one 5 pin 5 amps socket outlet on the independent board.

All as per item No 63 above but for one 3 pin 5 amps socket outlet on the same board with other switchs.

All as per item No 63 above but for Call bell point.

All as per item No 63 above but with 2.5 Sqmm PVC insulated stranded copper conductor cable for one 3 pin 15 Amps socket outlet. In and including S/C 2.5 Sq mm PVC insulated copper conductor unsheathed 1100 v grade IS -694 FR cable for continuous earth wire.

M&L for point wiring with 1.5sqmm PVC insulated unsheathed multi stranded copper conductor cable drawing in existing steel/PVC conduit with 1.5 Sq mm PVC insulated copper conductor cable for continuous earth wire connected to main earth dolly excluding 3mm sheet metal box and hylam sheet complete for one light point controlled by one switch complete all as specified and directed by Engineer in Charge.

All as per srl item 69 above but for one fan point controlled by one switch through regulator.

All as per srl item 69 above but for one 5 pin 5 amps socket outlet on the independent board.

All as per item No 69 above but for one 3 pin 5 amps socket outlet on the same board with other switchs.

All as per item No 69 above but for Call bell point.

All as per item No 69 above but with 2.5 Sq mm PVC insulated stranded copper conductor cable for one 3 pin 15 Amps socket outlet. In and including S/C 2.5 Sq mm PVC insulated copper conductor unsheathed 1100 v grade IS -694 FR cable for continuous earth wire.

S&F in replacement switch piano, flush type single pole, one way, 6 Amps, 240 volts all as specified and directed by Eng-in-charge.

S&F in replacement Socket outlet 2 in 1, 3 pin,6 A, 240 volts all as specified and directed by Eng-in-charge.

S&F in replacement switch piano, flush type single pole, one way, 16 Amps, 240 volts all as specified and directed by Eng-in-charge.

S&F in replacement socket 16 Amps, 2 in 1, flush type all as specified and directed by Eng-in-charge.

Supply & fix in replacement bell push, flush type, 5 Amps, 240 volts all as specified and directed by Eng-in-charge. .

S&F in replacement Fan Regulator step type 120 watt, 240 volt complete.

S&F in replacementModular Fan step regulator, 120W step type 120 watt, 240 volt complete.

S & F Modular switch 1 way 6A, 1 modules suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge.

S & F Modular Socket, 6A - 2/3 pin combined 2 module, suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge.

S & F Modular switch 2 way 6A, 1 modules suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge.

S&F Modular switch 1 way 16A, 1 modules suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge.

S & F Modular Socket, 16A 2/3 pin combined 2 module, suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge.

Supply and fix Modular bell push 1 Module 5 Amps suitable for 240 volt Complete all as specified and directed by Engineer-in-Charge.

Supply and fix White cover plate with frame,2 module Complete all as specified and directed by Engineer-in-Charge.

Supply and fix White cover plate with frame,3 module Complete all as specified and directed by Engineer-in-Charge. Make: Crabtree/Anchor/Orient

Supply and fix White cover plate with frame,4 module Complete all as specified and directed by Engineer-in-Charge.

Supply and fix White cover plate with frame,6 module Complete all as specified and directed by Engineer-in-Charge.

Supply and fix White cover plate with frame,8 module Complete all as specified and directed by Engineer-in-Charge.

S & F Modular metal flush box 3 module Complete all as specified and directed by Engineer-in-Charge.

S & F Modular metal flush box 4 module Complete all as specified and directed by Engineer-in-Charge.

S & F Modular metal flush box 6 module Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement ceiling roses, surface bakelite 65x50mm ,3 terminals 3 phase, PVC/Polycarbonate, isolated body all as specified and directed by Eng-in charge

Taking down the old white hylium sheet from the existing flash metal box and replacing new supper quality white hylium sheet of size 9" x 13" complete all as specified and as directed by Engineer-in-Charge.

All as per srl item 97 above but of size 8" x 5" complete all as specified and as directed by Engineer-in-Charge.

All as per srl item 97 above but of size 7" x 5" complete all as specified and as directed by Engineer-in-Charge.

All as per srl item 97 above but of size 5" x 5" complete all as specified and as directed by Engineer-in-Charge.

Taking down rusted sunkan metal box and fixing new metal box of 3 mm thick of size 8''x5'' with finishig of disturbed surfaced as directed by Engineer in charge.

Taking down rusted sunkan metal box and fixing new box of 3mm thick of size 8''x5'' with finishig of disturbed surfaced as directed by Engineer in charge.

Taking down rusted sunkan metal box and fixing new box of 3mm thick of size 7" x 5" with finishig of disturbed surfaced as directed by Engineer in charge.

Taking down rusted sunkan metal box and fixing new box of 3mm thick of size 5" x 5" with finishig of disturbed surfaced as directed by Engineer in charge.

S&F in repair of sub main wiring with 2 single core 04 Sq mm PVC insulated unsheathed 1100 V grade copper conductor cable drawing in existing rigid non- metallic PVC/metallic conduit incl 4.0 Sq mm PVC insulated single core copper conductor cable for continuous earth wire.

S&F in repair of sub main wiring with 2 single core 06 Sq mm PVC insulated unsheathed 1100 V grade copper conductor cable drawing in existing rigid non metallic PVC conduit incl 6.0 Sq mm PVC insulated single core copper conductor cable for continuous earth wire.

S&F in repair of sub main wiring with 2 single core 04 Sq mm PVC insulated unsheathed 1100 V grade copper conductor cable drawing in and incl rigid non metallic PVC conduit 25 mm dia incl 04 Sq mm PVC insulated single core copper conductor cable for continuous earth wire.

S&F in repair of sub main wiring with 2 single core 06 Sq mm PVC insulated unsheathed 1100 V grade copper conductor cable drawing in and incl rigid non metallic PVC conduit 25 mm dia incl 6.0 Sq mm PVC insulated single core copper conductor cable for continuous earth wire.

S&F in repair of sub main wiring with 2 single core 10 Sq mm PVC insulated unsheathed 1100 V grade copper conductor cable drawing in and incl rigid non metallic PVC conduit 32 mm dia incl 10 Sq mm PVC insulated single core copper conductor cable for continuous earth wire.

M & L for rigid non metalic PVC medium grade conduit including junction boxes, tee, bends, elbows, reducers bell mouth tube ends,fixing accessories such as couplers, lock Nuts, saddle pipe hook etc for 25 mm dia.ISI Marked.

Supply & fix in replacement of Casing capping double lock type supper quality size 20 mm width ISI marked with fixing accessories complete all as specified and directed by Engineer in Charge.

Taking down of LED/Tube light/CFL fitting of any type of make and removing material to store for keeping in safe costudy or for reuse or taking credit and making good distrub surface of walls,floor etc complete all as specified and directed by the Engineer- In- Charge.

Supply and fixing wall mounted LED batten extruded aluminium heat shrink provided for efficient heat dissipation and integrated electronic driver ,20 watt LED fitting with 100 lumen/watt, 6000K , 230 Volts, diffused optics ,etc complete with all accessories , connecting up with twin core twisted flexible copper conductor cable from ceiling rose to fitting, and testing complete all as specified and directed by the Engineer- In- Charge.

Supply and fixing wall mounted LED batten extruded aluminium heat shrink provided for efficient heat dissipation and integrated electronic driver ,10 watt LED fitting with 100 lumen/watt, 6000K , 230 Volts, diffused optics ,etc complete with all accessories , connecting up with twin core twisted flexible copper conductor cable from ceiling rose to fitting, and testing complete all as specified and directed by the Engineer- In- Charge.

Supply and fixing decorative LED wall light Nickel fitting premium opal glass for reduced glare designed for use with energy saving light bulbs suitable for 9/10 watt LED with 100 lumen/watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable from ceiling rose to terminal block, and testing complete all as specified and directed by the Engineer-In- Charge.

Supply and fixing ultra slim surface decorative 8/9 watt with 100 lumen/watt, 6000 K ,230 volt, LED ceiling fitting, complete with all accessories , connecting up with twin core twisted flexible copper conductor cable from ceiling rose to fitting, and testing complete all as specified and directed by the Engineer-In- Charge.

All as per item No 116 above but size 15 W complete all as directed by Engr-in-charge.

All as per item No 116 above but size 18W complete all as directed by Engr-in-charge.

S&F ultra modern design architectural design 34 watt 2x2 recess LED, 6000 K luminaire having glare free symmetrical illumination Complete all as specified and directed by Engineer-in-Charge.

S&F IN replacement electronic driver suitable for ultra modern 24 to 48 watt 2x2 recess LED, 6000 K luminaire Complete all as specified and directed by Engineer-in-Charge. .

All as per item No 120 above but Suitable for 9 to 18W complete all as directed by Engr-in-charge.

S&F in replacement heavy duty industrial batten with pre-coated CRCA body decorative type ,suitable for retrofit LED 1X18/20W LED tube complete all as specified and as directed.

Supply and fix in replacement lamp holder PVC/Poly Carbonate type suitable for LED Bulb with ISI mark complete all as specified and as directed by Eng-in-charge.

M& L for minor repair/service and greasing of bearings, cleaning of dust on ceiling fans with blades and canopys and reconnecting the electrical conections and with regulators complete all as specified and as directed by Engineer-in-Charge. Note: All required Materials are deemed to be included in the unit rate quoted.

M & L for repair to Ceiling fan of of any size by replacing unserviceable ball bearing of suitable size including neccessary greasing complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of fan capacitor with copper wire plastic body 2.5 mfd.

S&F in replacement of fan capacitor with copper wire plastic body 3.15 mfd.

S&F in replacement of rubber real for ceiling fan complete all as specified and directed by Engineer in Charge.

S&F in replacement of mild steel U clamps including 10 mm dia but, nuts, washers and split pin for ceiling fan complete all as specified and directed by Engineer in Charge.

S&F in replacement of mild steel fan hook made out of 12 mm dia mild steel round bar of suitable size as per existing hook as directed by Engineerin Charge.

S&F in replacement of upper louver conopy of ceiling fan of any sweep, make, modles & size as per existing complete as specified and directed by Engineer in Charge.

S&F in replacement of ceiling fan heady duty 1200 mm sweep including necessary fixing arrangement for proper fixing as per site requirement complete all as specified and as directed by Engineer-in-Charge.

M& L for minor repair/service and greasing of bearings, cleaning of dust on echaust fan fans with blades and reconnecting the electrical conections and with regulators complete all as specified and as directed by Engineer-in-Charge.

M & L for repair to exhaust fan/ of of any size ( 200 to 600 mm sweep) by replacing unserviceable ball bearing No 6201/6202/6203 including neccessary greasing complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of fan capacitor with copper wire plastic body 1.5 mfd suitable for exhaust fan

S&F in replacement of fan capacitor with copper wire plastic body 4. mfd suitable for exhaust fan

S&F in replacement of exhaust fan heavy duty plastic body 200 mm sweep including necessary fixing arrangement for proper fixing in wall and making hole as per site requirement complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement of exhaust fan heavy duty metal body type 225/230 mm sweep including necessary fixing arrangement for proper fixing in wall and making hole as per site requirement complete all as specified and as directed by Engineer-in-Charge.

All as per item No 138 above but size of exhaust fan 250 mm sweep complete all as directed by Engr-in-charge.

All as per item No 138 above but size of exhaust fan 300 mm sweep complete all as directed by Engr-in-charge.

All as per item No 138 above but size of exhaust fan 450 mm sweep complete all as directed by Engr-in-charge.

All as per item No 138 above but size of exhaust fan 600 mm sweep complete all as directed by Engr-in-charge.

S&F in replacement of wall mounting fan heady duty 450 mm sweep including necessary fixing arrangement for proper fixing on wall as per site requirement complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement of exhaust fan louvers fan suitable for 225/230/250 mm sweep including necessary fixing arrangement for proper fixing on wall as per site requirement complete all as specified and as directed by Engineer-in-Charge.

Cutting of existing surface/wall for making hole suitable for fixing of exaust fan of required size including 04 Nos hold fastner and making good the disturbed surface all as specified and as directed by Engineer-in-Charge.

Supply & fix in replacement PVC FRLS Flexible cable copper conductor, unsheathed , 1100 volts grade confirming to IS:694/1990 of size 1.5 sqmm complete all as specified and as directed by Engineer in Charge.

Supply & fix in replacement PVC FRLS Flexible cable copper conductor, unsheathed , 1100 volts grade confirming to IS:694/1990 of size 2.5 sqmm complete all as specified and as directed by Engineer-in- charge.

Supply & fix in replacement PVC FRLS Flexible cable copper conductor, unsheathed , 1100 volts grade confirming to IS:694/1990 of size 4.0 sqmm complete all as specified and as directed by Engineer-in- charge.

Supply & fix in replacement PVC FRLS Flexible cable copper conductor, unsheathed , 1100 volts grade confirming to IS:694/1990 of size 6.0 sqmm complete all as specified and as directed by Engineer-in- charge.

Supply & fix in replacement of flood light 50 watt, high power LED 3000/6000K energy saving, Highly efficient integral type mid power made of pressure die cast aluminium housing with 10 KV SPD, toughned glass, w/o Lens.IP66, suitable for highlighting architectural features orretail spaces complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement of LED Security Light 45 watt, LUMOS-SUPER Highly LED street light made of pressure dia cast aluminium housing with high power LEDs, lens & toughened glass, IP66, light distribution Efficacy>110Lm/W. 5700K. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V .

S& F in replacement sub main wiring with two single core PVC insulated unsheathed cable 1100 volts FRLS grade with multi strand copper conductor and drawn through and including PVC conduit along with continuous earthing wire but in green colour complete on surface/concealed and connected to common earth dolly of the following size. Note : Three run of PVC cable and one run of PVC conduit shall be measured as one unit length. (a) 4 Sqmm ( 2 single run of 4 Sqmm and one run of 4 Sqmm as earth wire)

(b) 6 Sq.mm ( 2 single run of 6 Sqmm and one run of 6 Sqmm as earth wire)

Supply & fix in replacement of MCCB four Pole 125 Amps, 415 volt thermal release bearing cap 16 KA comlete all as specified and as directed by Engineer-in-Charge.

Supply & fix in replacement of MCCB four Pole 100 Amps, 415 volt thermal release bearing cap 16 KA comlete all as specified and as directed by Engineer-in-Charge.

Supply & fix in replacement of MCB TP, 100 Amps, 10 KA 440 volt 50 Hz all as specified ans directed by engineer in- charge.

S&F of LED ceiling light 34 watt 2x2 recess LED, 6000 K luminaire having glare free symmetrical illumination Complete all as specified and directed by Engineer-in-Charge.

Maintenance and general servicing 'B' Check of DG sets of following capacities of any make including replacing of Engine Oil, oil filter, fuel filter, air Filter, fuel hose, water separator, By-pass filter, air cleaner and topping up of coolant etc. complete including general cleaning including cleaning of accoustic enclosures of DG set with the help of air blowers complete and if required replacing of O ring,nut, bolt,washers etc complete all as specified and as directed by the Engineer-In- Charge. (a) 320 KVA DG set

(b) 200 KVA DG set

© 125 KVA DG set Note : (i) The work shall be executed only though authorised service provider of OEM of respective DG set. The contractor has to submit MOU with the authorised service provider duly noterised and uploaded at the time of submission of bid documents. (ii) The authorised service provider shall give his complete investigation report of respective DG set seperately on his first visit to each DG set including the complete details of repairs to be carried out with warrantee of 2 years for parts replaced by authorised service provider of OEM. (iii) No repair work other than essential repair work indicated in the investigation report of the service provider for respective DG set will be carried out. (iv) The rate quoted for BOQ item Nos. 158 to 160 include supply and fixing of carbon brush set with holder, solenoid switch assembly with bush, commuter unit, stator starting and running coil.

Disconnecting all electrical cable connections from the dynamo assembly and taking down the dynamo assembly for carrying out repairs and complete overhauling the system including replacing the unserviceable parts like Carbon brushes, Bearings, Armature. Burnt out coils etc. reassembling and re-fixing the dynamo assembly to its original position and reconnect all disconnected cable connections including testing complete for the following capacities of DGs complete all as specified and as directed by the Engineer-In- Charge. (a)320 KVA DG set

(b) 200 KVA DG set

© 125 KVA DG set Note : The work shall be executed only though authorised service provider of OEM of respective DG set. The contractor has to submit MOU with the authorised service provider duly noterised at the time of submission of bid documents.

Supply & Fix 24 Volts 30 Amps battery Charger, panel mounting type including removing the unserviceable battery Charger from the existing position complete all as specified and as directed by the Engineer-In- Charge.

Supply and fix in repair lead acid maintenance free batteries 180 AH, 12 V, 25 plates complete all as specified and as directed by the Engineer-In- Charge.

Supply and connect maintenance free lead acid battery 12 Volt, 150 AH complete all as specified and as directed by the Engineer-In- Charge.

Draining out the fuel from the fuel tank of DG Set of various capacity and keeping it in separate container, disconnecting all the fuel lines and other mechanical connections and taking out the fuel tank for cleaning, cleaning the fuel tank both internally and externally by removing all the accumulated dust / sediments, leak testing the tank and welding / brazing if required and re-fixing the tank to its original position, replacing the drain plug and PVC pipe protected with steel flexible pipe, calibrating the fuel tank, refilling the drain out fuel back into the tank and provision of locking arrangements complete all as specified and as directed by the Engineer-In- Charge.

Repairs to radiator of copper/aluminium all types taking out by disconnecting from DG set locating the leaking places and trnasposting to workshop for soldering / brazing complete including cleaning with acid and refixing in position complete all as direcetd incl replacement of hoses with new one for DG sets of capacity 125 KVA complete all as specified and as directed by the Engineer-In- Charge.

Repairs to radiator of copper/aluminium all types taking out by disconnecting from DG set locating the leaking places and trnasposting to workshop for soldering / brazing complete including cleaning with acid and refixing in position complete all as direcetd incl replacement of hoses with new one for DG sets of capacity 320/200KVA complete all as specified and as directed by the Engineer-In- Charge.

Repairs to radiator of copper/aluminium all type taking out by disconnecting from DG set locating the leaking places and trnasposting to workshop for soldering / brazing complete including cleaning with acid and refixing in position complete all as direcetd incl replacement of hoses with new one for DG set of capacity 125 KVA complete all as specified and as directed by the Engineer-In- Charge.

Disconnecting and taking down the defective / unserviceable DC wiring and rewiring with same size of cable including supply and replacing of complete wire with flexible pipe, control cable including testing complete for following capacities of DG Set complete all specified and directed by engineer- in- charge :- (a) 320 KVA DG set

(b) 200 KVA DG set

© 125 KVA DG set

M&L for servicing of AMF panel of DG set of capacity 125 KVA cleaning of AMF panel, rectification of defect rewiring replacement of D/S indicator,fuse, timer. and new indicator of complete AMF panel and replacement of unserviceable relays under respective item of this schedule complete all as specified and as directed by the Engineer-In- Charge.

M&L for servicing of AMF panel of DG set of capacity 320/200 KVA cleaning of AMF panel, rectification of defect rewiring replacement of D/S indicator,fuse, timer. and new indicator of complete AMF panel and replacement of unserviceable relays under respective item of this schedule complete all as specified and as directed by the Engineer-In- Charge.

Supply & Fix in replacement of digital multi function meter to read voltage, current and power factor including set of CT-1 each complete all as specified and as directed by the Engineer-In- Charge.

Supply & Fix in replacement of 3 pole power contactor MNX 185 , 185 Amps complete all as specified and as directed by the Engineer-In- Charge.

Supply & Fix in replacement of 3 pole power contactor MNX MNX 300 , 300 Amps complete all as specified and as directed by the Engineer-In- Charge.

Supply & Fix in replacement of 3 pole power contactor MNX 225, 225 A complete all as specified and as directed by the Engineer-In- Charge.

Supply & Fix in replacement of solenoid switch suitable including all necessary arrangement complete all as specified and as directed by the Engineer-In- Charge.

Supply and replace engine oil from engine oil sump with suitable grade oil SAE-20W40 complete all as specified and as directed by the Engineer-In- Charge.

Supply & Fix in replacement self starter for suitable of 320 KVA DG set capcity including all necessary electrical connections complete all as specified and as directed by the Engineer-In- Charge.

Supply & Fix in replacement self starter for suitable of 200 KVA DG set capcity including all necessary electrical connections complete all as specified and as directed by the Engineer-In- Charge.

Supply & Fix in replacement self starter for suitable of 125 KVA DG set capcity including all necessary electrical connections complete all as specified and as directed by the Engineer-In- Charge.

S&F in repair fan belt with provided new fan belt DG set pf capacity 125- 200 KVA complete all as specified and as directed by the Engineer-In- Charge.

S&F in repair belt for water pump ( set ) in 320 KVA DG set for greevs complete all as specified and as directed by the Engineer-In- Charge.

S&F in repair belt for belt water pump ( set ) in 320 KVA DG set complete all as specified and as directed by the Engineer-In- Charge.

M&L for locating fault in LT/HT (1.1/11 KV grade) underground cable laid in trenches by locating fault with the help of electronic fault locator machine comprising of surge generator pulse ECHP fault location with high frequency distance calculator etc. Excavation in any type of soil strata exposing the cable fault removal of deteriorated position of cable treating of cable and keeping the same ready for jointing work for cables of size upto 400 Sqmm 3.5 core/ 300 sq mm 3 core. The fault locating equipment will be brought to site within 02 hours of instruction received from Engineer-in-Charge complete all as specified and as directed by the Engineer-In- Charge.

Supply and fix in replacement aluminium Tube terminal ( thimbles) of size 50 to120 Sqmm XLPE Cable complete all as specified and as directed by the Engineer-In- Charge.

Supply and fix in replacement aluminium Tube terminal ( thimbles) of size 150 to 240 Sqmm XLPE Cable complete all as specified and as directed by the Engineer-In- Charge.

M&L for de-scaling / Servicing of radiator unit of DG set capacity 125 to 320 KVA including draining water, filling & circulating chemical and flushing complete including minor spare as inlet and outlet hose pipes of required size, jublee clamps etc as required complete all as specified and as directed by the Engineer-In- Charge.

S & F in repair of PT fuel pump by dismantling, transporting, repairing and calibration, testing and commissioning of PT fuel pump for 320 KVA DG set including the replacement of all service kits, pulsvation damper, tacho drive shaft and seal, gear drive shaft , bearing, weight carriers, etc complete all as specified and as directed by the Engineer-In- Charge.

All as per item No. 192 above but of capacity 200 KVA complete all as specified and as directed by the Engineer-In- Charge.

All as per item No. 192 above but of capacity 125 KVA complete all as specified and as directed by the Engineer-In- Charge.

Supply and fix oil safety switch to engine of 320/200/125 KVA DG set as per existing complete all as specified and as directed by the Engineer-In- Charge.

Supply and fix in replacement the corrosion resistor as per existing to the Engine of DG set capacity 320/200/125 KVA complete all as specified and as directed by the Engineer-In- Charge.

Supply and fix in replacement gear tachometer for DG set of capacity 320/200/125 KVA as per existing complete all as specified and as directed by the Engineer-In- Charge.

Supply and fix in replacement exhaust manifold set of three pieces complete with gaskets , stud mountings, nuts etc complete ( centre , rear and front) in 320/200/125 KVA DG set complete all as specified and as directed by the Engineer-In- Charge.

M&L for repair including replacement of coils , bush/ bearings and other spares as required to alternator/dynamo unit of DG set of capacity 320/200/125 KVA complete all as specified and as directed by the Engineer-In- Charge.

M&L for repair the water pump of DG set 320/200/125 KVA including replacement of impeller, ball bearing, shaft, spacer, plug and seal complete all as specified and as directed by the Engineer-In- Charge.

M & L for asbestos rope 12 mm dia for wrapping the exhaust pipe of DG set complete all as specified and as directed by the Engineer-In- Charge.

S&F in repair Air filter suitable for 320/200/125 KVA DG set complete all as specified and as directed by the Engineer-In- Charge.

M & L for repair and reconditioning the starting motor of kirloskar / cummins / Greaves make including taking out the defective starter from 320/200/125 KVA / capacity DG set , complete dismantling and repair and replacing the carbun brushes with holder, solenoid switch assly, bush, commutator unit, starting coil, etc refixing the same in the DG set and connecting with the circuit including all required items, starting and testing complete all as specified and as directed by the Engineer-In- Charge. Note : Rate quoted shall be for removing , refixing incl overhauling of starter & spares parts required will be measured and paid separately as supply ony under respective item.

M & L for repair and reconditioning the starting motor of kirloskar / cummins / Greaves make including taking out the defective starter from 320 KVA / capacity DG set , complete dismantling and repair and replacing the carbun brushes with holder, solenoid switch assly, bush, commutator unit, starting coil, etc refixing the same in the DG set and connecting with the circuit including all required items, starting and testing all as specified and directed by Engineer-in-charge Note : Rate quoted shall be for removing , refixing incl overhauling of starter & spares reqd will be measured and paid separately as supply only.

M & L for taking down stator assembly of alternator by disconnecting electrically and mechanically taking to work shop for rewinding incl removing burnt coils, insulating material complete cleaning with CTC and rewinding with same gauge ISI marked winding wire complete with ISI marked insulating paper and Dr Beck varnish baking / heating and bringing back to installatin refixing , connecting elecrtically and mechanically and testing on completion of work complete all as directed for DG set of capacity 320/200/125 KVA complete all as specified and as directed by the Engineer-In- Charge.

M & L for taking down stator assembly of alternator by disconnecting electrically and mechanically taking to work shop for rewinding incl removing burnt coils, insulating material complete cleaning with CTC and rewinding with same gauge ISI marked winding wire complete with ISI marked insulating paper and Dr Beck varnish baking / heating and bringing back to installatin refixing , connecting elecrtically and mechanically and testing on completion of work complete all as directed for DG set of capacity 320 KVA complete all as specified and as directed by the Engineer-In- Charge.

S & fix solid state potentiometer under cummins part no. 3877372 in 320/200/125 KVA and testing complete all as specified and as directed by the Engineer-In- Charge.

Supply only coolant for radiator suitable for DG set 320/200/125 all as per manufacturers recommendations and complete all as pecified and as directed by the Engineer-In- Charge.

S & F start and stop relay 12 V/24 V DC suitable for AMF Panel capacity of 320/200/125 KVA all as per manufacturers recommendations and complete all as specified and as directed by the Engineer-In- Charge.

S & Fix in repairs Lub oil pressure transducer in 320 KVA DG set and connecting with DG set system all as per manufacturers recommendations complete all as specified and as directed by the Engineer-In- Charge.

S & Fix in repairs Low lub oil pressure safety make in 200/125 KVA DG set and connecting with DG set system complete all as specified and as directed by the Engineer-In- Charge.

Supply, installation and commissioning of radiator for 125 KVA DG set under including dismantling of old / defective radiator, taking out from DG set base frame, fixing the new radiator assembly, fan and shroud of radiator, connecting cooling pipes inlet and outlet complete all as specified and as directed by the Engineer-In- Charge.

Supply, installation and commissioning of radiator for 320/200 KVA KVA Cummins DG set under including dismantling of old / defective radiator, taking out from DG set base frame, fixing the new radiator assembly, fan and shroud of radiator, connecting cooling pipes inlet and outlet complete all as specified and as directed by the Engineer-In- Charge.

M/S LADPURIA ENTERPRISES

M/S MG GROUP