Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹24.7 LAccepted-AOC | L1 | Accepted-AOC Awarded being lowest | |
| 2 | L2₹27.4 L+₹2.8 L (11.2%)Rejected-Finance | L2 | Rejected-Finance Rejected being L2 bidder |
Tender Value
Refer Docs
EMD Value
₹53,619
Closing Date
6 May 2024, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
CWE, HQ 133 Works Engrs
HQ 133 Works Engrs
PROVN OF CONNECTING PASSAGE TO CORPS HQ BLDG AT BB CANTT, SRINAGAR UNDER GE 864 EWS
2024_MES_649053_1
CWEK-90/2023-24
Open Tender
Civil Works
Item Rate
180 days
GE 864 EWS
Class D Category a i and b i
7 documents required · 7 mandatory
₹500
GE 864 EWS
₹53,619
HQ 133 Works Engrs
26 Jun 2024
2 Apr 2024
13 May 2024
2 Apr 2024
6 May 2024
16 Apr 2024
2 Apr 2024 - 10 Apr 2024
11 Apr 2024
Amount
Excavation over area not exc 1.5m in depth and getting out, in soft/loose soil complete all as specified and directed by Engr-in-Charge.
Excavation over area exc 1.5m not exc 3.0m in depth and getting out, in soft/loose soil complete all as specified and directed by Engr-in-Charge
Excavation in trenches not exc 1.5m wide and not exc 1.5m in depth for foundation etc or for walls, shafts, manholes not exc 10 Sqm on plan and getting out, in soft/loose soil complete all as specified and directed by Engr-in-Charge
Material and labour for PCC 1:4:8 type D-2 using 40 mm graded mechanically crushed stone aggregates as in foundation, sub base and mass concrete complete all as specified and directed by Engr-in-Charge
Use and waste of form work to side of concrete, foundation, footing bases of columns plinth beams & similar work vertical or to batter for rough finished surfaces of concrete complete all as specified and directed by Engr-in-Charge.
Material and labour for RCC 1:2:4 type B-0 using 12.5 mm graded mechanically crushed stone aggregates as in Foundations, including rafts,footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed by Engr in Charge.
Use and waste of form work to sides of pillars,posts, struts, pears, columns & stanchion square or rectangular or polygonal etc with rough finished surface of concrete complete all as specified and directed by Engr-in-Charge
Material and labour for RCC 1:2:4 type B-0 using 12.5 mm graded mechanically crushed stone aggregates as in Columns, pillars, piers, postsand struts complete all as specified and directed by Engr in Charge.
Use and waste of form work to sides and soffits of roof beams, lintel, cantilevers including supports etc with rough finished surface of concrete complete all as specified and directed by Engr-in-Charge.
Material and labour for RCC 1:2:4 type B-0 using 12.5 mm graded mechanically crushed stone aggregates as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engr in Charge.
Use and waste of form work to sides and soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc with rough finished surface of concrete complete all as specified and directed by Engr-in-Charge
Use and waste of form work toto edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide etc with rough finished surface of concrete comcomplete all as specified and directed by Engr-in-Charge
Reinforced cement concrete 1:2:4 type B-1 using 20mm graded mechanically crushed graded mechanically crushed stone as in slab supported on walls, colomns, beams, shelves etc complete all as specified and directed by Engr-in-Charge
Supply and fix mild steel deformed bars or TMT bars, 10 mm dia and over, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed by Engr-in-Charge
Material and labour for Mild steel TMT bars ,8mm dia and over upto and including 10mm dia bars as in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge
Returning filling in including spreading leveling watering and well ramming in layers not exc 25 cm thick each complete all as specified and directed by Engr-in-Charge
Removing excavated materials to a distance n. exc 50m and depositing where directed at a level not exc 1.5 m above the starting point in soft/loose soil complete all as specified and directed by Engr-in-Charge
Material and labour for brick work with sub class B bricks of old size, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6 complete all as specified
Material & Labour for rendering 15mm thick in CM 1:4 on any face of brick wall/concrete surfaces and finished even & smooth without using extra cement complete all as specified and directed by Engr-in-Charge
Material & Labour for rendering 15mm thick in CM 1:6 on fair faces of brick wall/concrete surfaces and finished even & smooth without using extra cement complete all as specified and directed by Engr-in-Charge
Material and labour for rendering 5 mm thick in cement mortar 1:3 on ceiling concrete surfaces and finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge
Material and labour for preparation of new plastered surfaces on walls and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified and directed by Engr-in-Charge
Material and labour for preparation newly plastered surfaces of walls, etc and applying two coats of Oil bound distemper over a layer of 1mm thick Birla putty etc complete all as specified and directed by Engr-in-Charge
Material and labour for preparation of newly plastered surfaces of ceiling and applying three coats of white lime wash complete all as specified and directed by Engr-in-Charge
Material and labour for Vitrified ceramic light shade tiles,10 mm thick (square / rectangular) area of each tile not exceeding 0.36 Sqm in floor etc laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed in neat cement slurry or with adhjesive as per the manufecturer's instructions and pointed in white or coloured cement to match comcomplete all as specified and directed by Engr-in-Charge
Material and labour for Vitrified ceramic light shade tiles,10 mm thick (square / rectangular) area of each tile not exceeding 0.36 Sqm in floor etc laid over and including 10 mm thick screed bed in cement mortar 1:4, set and jointed in neat cement slurry or with adhjesive as per the manufecturer's instructions and pointed in white or coloured cement to match complete all as specified and directed by Engr-in-Charge
Supply and fixing 25 mm thick granite (of any type) work (table rubbed and polished) as in strips in floors, steps,jambs,pillars, windowcills, cooking platform and like in CM 1:4, laid over screed bed 15mm thick in CM 1:4 including jointing , pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite and rubbing polish to achieve mirror finish complete all as specified and directed by Engr-in-Charge
S&F frameless toughened glass door with sliding shutters (02 Nos) or side hinghed type shutter 12mm thick, factory toughened plain sheet glass, using the stainless steel fitting of polished chrome finish, in each shutter (satin stainless steel finish for handles) including cutting necessary holes and cutouts complete all as specified and as directed by Engr-in-charge. (a) Lock patches with EPC nad strike plate XL-C-4011A:01 No (for openable shutter) (b) Floor spring 90mm opening (EN4) 01 No (for openable shutter) (c) Top patches XL-C 4012: 01 No (for openable shutter) (d) Bottom patches XL-C 4013: 01 No (for openable shutter) (e) Top pivots XL-C 4014: 01 No (for openable shutter) (f) 450mm long H-Type handles 25mm dia of grade SS-304, XL-C-3003A: 01 No (01 Set for openable shutter)
Supply and fixing rolled mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe-410-W (Gde- E-250) quality- A complete all as specified and directed by Engr-in-Charge
Supply and fixing Mild steel screw bolts 5-10 mm neck dia, machine made with hexagonal or square head at one end embede in RCC fencing post while casting & screwed the other, to be fitted with washer & one hexagonal or square nut exc 15 cm but not exc 22.50cm long complete all as specified and directed by Engr-in-Charge
Supply and fixing rolled mild steel work in tubular trusses including vertical member, rafter and purline including special shaped washer etc using ERW or induction butt welded tubes conforming to IS 1161-1979 graded st- 240 including cutting to dead length, notching, drilling riveting and/or welding & connecting with nuts & bolts complete all as specified and directed by Engr-in-Charge
Material and labour for preparation of new steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge
Supply and fixing pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick, ,of any tint,having tensite strength of 550m mpa as in roof covering/ cladding to wall, fixed with L or J type hooks or coach screws with washers or with self tapping screws complete all as specified and directed by Engr-in-Charge
Supply and fixing pre-painted galvatume aluminium zinc coating GI based palin steel sheet 0.5mm thick, ,of any tint,having tensite strength of 550m mpa, as in ridge to roof, fixed with self taping screws complete all as specified and directed by Engr-in-Charge
S&F aluminiun anodised snap grid ceiling of frame size 600 x Sqm 600mm, main Tee section of size 36.5mm x 25mm x 1.4 mm thick cross Tee section of size 23.5mm x26.4 mm x1.4 mm thick. supported at ends all along the wall with aluminium anodised angle of size 40 mm x 25 mm x 2 mm thick and 4mm dia Gl suspenders including Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed by Engr-in-Charge
M&L wooden khatamband ceilling over 12mm thick plywood. Grade BWR type BB, fixed with nails to timber frame work, fixed in ceiling over wooden fillets of 2nd class softwood. wrought rectangular in section of sectional area exc 13 Sqcm and n.exc 25 sqcm and triangular in section secured with nails or brads anging with roof truss through 6mm dia Gl wire and including three coat of french polishing as on approved by GE including necessary frame work complete all as specified and directed by Engr-in-Charge
Supply and fixing 2nd class hard wood (sal) weather boarding, clean sawn,plain 20 mm thick width n exc 25mm thick & fixed with 30 mm laps & wriught both sides and edges shot & chamfered ( on exposed edges) complete all as specified and directed by Engr-in-Charge
Material and labour for preparing new or previously untreated wood or wooden surfaces of any description not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over one coat of pink primer comcomplete all as specified and directed by Engr-in-Charge
Demolition of brick work built in cement mortar including all quoins, pillars etc but excluding ashlar facings, dressed stone work and precast articles complete all as specified and directed by Engr-in-Charge
Taking down chowkhats or frames exc 1.5 sqm and not exc 4 sqm each with shutters (without taking off shutters from the frame) and removing from site, complete all as specified and directed by Engr-in-Charge
Surface excavation n.exc. 30centimetre deep and averaging 15 centimetre deep and getting out in soft/loose soil complete all as specified and directed by Engr-in-Charge
Hard core of broken stone or boulders of gauge n.exc 63 mm deposited spread and leveled in layers n.exc 15 cm thick watered and rammed to a true surface complete all as specified and directed by Engr-in-Charge
Material and labour for 100mm thick PCC 1:2:4 type B-2 using 40mm graded mechanically crushed stone aggregates as on foot path complete all as specified and directed by Engr-in-Charge.
Material and labour for cement concrete chequered tiles 20cm X 20cm X 25 mm thick with grey cement and pigment, machine pressed, factory made, set, jointed and pointed in neat cement slurry in floors over and including screed bed 15mm thick in cement mortar 1:6 finished even and fair complete all as specified and directed by Engr-in-Charge.
M&L for making single phasing point wiring system used as copper conductor wire for phase and neutral wiring system the wire made out of PVC insulated FRLS of 1100 volt grade with having multistranded copper conductor wire of size 1.5 Sq mm (Nominal area) ISI Marked drawn through in any lengthy inside size in heavy duty ISI mark PVC casing capping strip or PVC conduit pipe of suitable along with its all connected fittings accessories including providing of modular type / size of pressed steel terminal sunken boxes or PVC flush type box heavy duty any type/ size for mounting of modular controling accessories and duly fixed it concealed in wall or surface on wall and also providing of modular type back and face top covered plate frame for housing / mounting of modular switches sockets, regulators etc and including using/ drawing of one run of single wire 1.5 sqmm PVC insulted FRLS wire 1100 volt grade ISI marked with multistranded copper conductor wire used as a continuous earth wire for point wiring complete system and including making the good to all disturbed surfaces of wall/ ceiling area of new wiring system and to match to it as per the existing furface of wall/ ceiling etc complete all as specified and directed by Engr-in-Charge.
(a) Description complete all as per above sr item No 46 but one light point/ fan point wiring system controlled by one way switch complete all as specified and directed by Engr-in-Charge.
(b) Description complete all as per above sr item No 46 but one 5 Amp socket outlet point wiring system fixed on independent board & controlled by one way switch complete all as specified and directed by Engr-in-Charge.
Description of all as per above sr item No 46 But using PVC insulated FRLS wire 1100 Volt grade with multistranded copper conductor wire of size 2.5 sq mm (Nominal area) ISI Marked for power socket point on independent board point wiring system and also providing of 2.5 sqmm PVC insulated FRLS wire 1100 volt grade ISI Marked with multistranded copper conductor wire used as a continuous earth wire for power point wiring system complete all as specified and directed by Engr-in-Charge.
Supply and fixing modular type switch 5/6 Amps 230 Volts, One module type/ size complete for one way switching system etc complete all as specified and directed by Engr-in-Charge.
Supply and fixing modular type switch 5/6 Amps AC 230 Volts 3/5 pin type combined with two modular type/ size etc complete all as specified and directed by Engr-in-Charge.
Supply and fixing modular type switch 15/20 Amps 230 Volts , one module size / type complete for one way switching system. Make Legrand Arteor or equivalent in Anchor Roma/ Havells Crab tree.
Supply and fixing modular type switch 15/20 Amps AC 230 Volts 5/6 pin type combined with two modular type/ size etc complete all as specified and directed by Engr-in-Charge.
Supply and fixing of recessed / ceiling concealed mounted flate unique square slim panel integrated design LED luminaire light panel type fitting of size of 2 feet x 2 feet type of rating capacity in 36W/40W decorative type with high performance LEDs and eletronic driver and extruded body made of aluminum housing with mounting slot and fully diffused long life energy saving and required fitting use in both warm/ white type colour set all as per of make of Philips & model No RC375B LED 36S 865/840 PSU W60L60 52 WH or equivalent make of Havells & mode no VENUSNE 02X2PLR36WLED865 PRALMOD or equivalent make crompton & model No CCR-127-36-57-SL-NWH complete set including making in additional extra cutting of existing hole side work on existing ceiling surface (when if required at site) for setting & fixing of new light fitting complete and also providing of suitable type of flate fexible of new light fitting complete and also providing of suitable type of flate ffexible two/ three core cable and makong electric connection and including taking down of old fitting etc complete all as specified and directed by Engr-in-Charge.
Supply and fixing recessed / ceiling concealed mounted down lighter light fitting of round/ Square flate slim shapes type, decorative type with integrated design LED luminaire light fitting of rating capacity In 15 W with electronic driver with extruded body made of aluminum/ PC housing and mounting slot with long life energy saving and required fitting use in both warm/ white type colour set all as per make of Philips & model No DN 177 15S LED DL G2 WW/NW/CW or equivalent make of Havells & model No EDGEPRONEORDDLR15WLED865S and or equivalent make Crompton & model No LSCRM 15W WW including making in hole or additional extra cutting of existing hole side work on existing ceiling surface (when if required at site) for setting & fixing of new light fitting complete and also providing of suitable type of flate fexible two/ three core cable and makong electric connection and including taking down of old fitting etc complete all as specified and directed by Engr-in-Charge.
Supply and fixing of sheet metal enclosure box duly powder coated & farming work with locking system and having double door fixing arrengment system suitable of size/ type of distribution board of rating SPN 8 way type 220 volt AC supply system with IP-43 protection rating with ISI marked and having neutral and earth link bus bar and mounting base chanel suitable for holding MCBs incommer and s outgoing system complete set and including dully fixed surface on wall or concealed in wall and making all necessary electrical connection including taking down of existing DBs etc complete all as specified and directed by Engr-in-Charge.
Supply and fixing of MCB SPN 40 to 63 Amps with breaking capacity 10KA 'C' curve series, 220 volts, 50 Hz AC supply complete and also making suitable size/ type of electric wiring connection complete including taking down of old MCB etc complete all as specified and directed by Engr-in-Charge.
Supply and fixing of MCB SP 10 to 32 Amps with breaking capacity 10 KA 'C' curve series, 220 volts , 50 Hz AC supply complete and also making suitable size/ type of electric wiring connection complete including taking down of old MCB etc complete all as specified and directed by Engr-in-Charge.
Supply and fixing of sub main wiring system with PVC insulated FRLs wire, 1100 volt grade with multistranded copper conductor wire of size/ type of single core 2 run of 16 Sqmm and 1 run of 16 Sqmm FRLS (Nominal area) ISI marked drawn through in heavy duty ISI marked PVC ceaing capping / PVC conduit of suitable size along with its all fittings and connected accessories and duly fixed concealed in wall or surface on wall including and making electrical connection & incluing taking down old unservicable sub main wiring system etc complete all as specified and directed by Engr-in-Charge.
M&L for earthing complete with galvanised steel earth plate electrode of 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised iron earth lead 4.00 mm dia by means of bolts nuts check nuts & washers of galvanised steel and to be protcted by GI pipe 15 mm bore light grade & connected to earth test point/ main switch board or main control board and also providing charcoal or coak and salt in alternative layers, necessary excavation and earth work in any type of soil all as shown in Electrical Plate No 3 of SSR part I. and also making arrangment of 20 mm dia bore galvanised iron pipe (medium grade) for water and making funner, wire mesh, and also including provision of concrete pit cover framing work in PCC (1:2:4) type B-1 using 20mm graded of stone aggregate with XPM (weight not less than 4 KG/Sqm) and outer frame work of angle iron 25x25x6 mm with top concret pit cover and handle for lifting of cover complete work etc complete all as specified and directed by Engr-in-Charge.
Supply and lay GI pipe 25 mm bore medium grade with fitting laid in trenches/ under road / floor / pole / wall for protection of vable including providing clamping arrangment for holding of pipe on pole/ wall in proper size of clamps, nut bolt , and washer etc complete all as specified and directed by Engr-in-Charge.
M/S Tajamul Ah Buchh
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .