Construction of Additional Accommodation for Circuit House ( Balance Work) at Canal Road Jammu

Amount

25mm thick fine dressed stone 20mm (average) thick base of cement mortar 1:5 (1 cement: 5 coarse sand), including pointing with cement mortar 1:2 ( 1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone and curing complete. Red sand stone including all leads, lifts and carriage (complete Job)

Extra for pre finished nosing in treads of steps of kota stone/ sand stone slab.

Providing and laying Ceramic Chequred floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. In colour such as White, Ivory, Grey, Fume Red Brown including all leads, lifts and carriage (complete Job)

Providing and fixing of glass pans weigting 13.75Kg/Sqm 5.5mm thick) with deodar wood fillets

French spirit polishing two or more coats on new work incl. a coat of wood filler shade wallnut or any colour as per directions of engineer- in -Charge.

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound@ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg./sqm. and coarse sand @1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around.

Providing and fixing stainless steel pipe curtain rods with s.s bracketes with clamps 25mm dia of supper quality hevay duty.

Providing and fixing supper of saint gobain with scews Aluminium decorative PVC frame on the sides of glass .

Providing & fixing of white vitreous China wall hung water closet (European Type) Italian collection (ENIGMA RIMLESS make Hindware CAT No. 92531 with concealed cistern, Kombifix Alpha (with frame and all accessories) with Actuator plates, make Gaberit, Veiga with CP bolts, nuts, CI chair hanging arrangements, bakelite seat & cover with CP hinges & rubber buffers, CP brass screw, washer with all accessories with WC connector with Rubber Lip / Buffer and side gap filled with silicon sealant wherever required. Including brass / SS screws and washer complete including cutting, making good the walls, floors, slab wherever required as per direction of Engineer-in-charge.

Providing & fixing of white vitreous china table top counter oval wash basin/circular basin (Hindware 91097, 91096) with CP brass waste assembly, CP cast brass bottle trap with extension piece (Hindware Cat No. 850072 , wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-in-charge

Providing & fixing of white vitreous china table top counter oval wash basin/circular basin (Hindware 91043 ) with CP brass waste assembly, CP cast brass bottle trap with extension piece (Hindware Cat No. 850072 ), wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-in-charge.

Providing and fixing concealed body for wall mounted basin mixer make Hindware Cat No. F850093, Jaquar Cat No. ALD 235, 233 ) including exposed part kit of single lever basin mixer wall mounted consisting of operating lever, wall flange and spout compatible with F 850093. Hindware Cat No. F 400013, F 3200013 or Jaquar DRC 33233 K include all accessories nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-in-charge

Providing and fixing body of Hi-Flow Single Lever concealed mixer and diverter for bath and shower system with diverter assembly and cartridge sleeve (Make Hindware Cat No. F850091BCP, Jaquar Cat No. ALD 075 ) Single lever exposed part kit of Hi-flow diverter consisting of operating lever wall flange Make Hindware Cat No. F400024, Jaquar Cat No. LYR 38193 K and bath spout Make Hindware Cat No. F400007, F320009, Jaquar Cat No. 37463 include all accessories nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-in-charge

Providing & fixing C.P. hand spray with lever control (health faucet) (Jaquar Cat. No. ALDCHR-565 / Hindware make 160013 ) and flexible hose 1 m long connection with C.P. holder for hand spray complete in all respects as per direction of Engineer-in-charge

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931). 15mm nominal bore (Make Jaquar CQT 23059 / Hindware Cat No. 400004 or equivalent).

Providing & fixing C.P. brass robe hook (Jaquar Cat No. ACN 1191N / Hindware Cat No. 870007 ) or approved equivalent) fixed to wall/door with plastic rawl plugs and C.P brass screws including cutting and making good the walls wherever required as per direction of Engineer-in-charge.

Providing & fixing recessed liquid soap dispenser (Jaquar Cat No. ACN 1135N ) as per direction of Engineer-in-charge

Providing and fixing of Soap Dish Holder with all fittings as per direction of Engineer-in-charge (Hindware Cat No. 840004 ).

Providing and fixing CP brass towel rail of approved make complete with CP brackets fixed to wooden cleats with CP brass screws. (Hindware Cat No. 880007 ).

P/F of glass shelf 600mm long with all C.P fittings of approved quality complete item (Hindware Cat No. 840011 ).

Providing and fixing toilet paper holder with all fittings Hindware Cat No. 870008 ).

Providing and fixing 15 mm dia. C.P. brass bib cock with wall flange of approved quality conforming to IS standard (Hindware Cat No. 400002 ).

Providing and fixing of regular body concealed stop cock suitable for 15mm pipe line with protection cap (Hindware Cat No. 850096, 400027 ) with exposed part angular stop cock with flange

Providing and fixing of wall mounted over head shower 200x200mm (Hindware Cat No. 160077 ) with shower arm 600mm long square shape Cat No. 190016 with 90 degree bend with flanges with all fittings.

Supply, Installing, testing of approved make of Tile insert shower drains and point drainage system, made of stainless steels, marine grade 316, with certification from the manufacturer. In shower areas / toilets / corridors etc. Make LIDL, LEDL and ACO.

Shower Drains, Size, L-600mm x 70mm x 22mm and outlet 98mm. Article No. SC-W-117.

Tile Insert Point floor drainage 150 x 150 x 98 outlet with tile depth 10mm. Article No. FD-Y-150

Supply, Installing, testing of approved make of Water Softener / scale control technology with advance crystallization process (ACP), Make Hydro-UK/Kitec-India. ACP 40 (1.5”).

Supply, installing, testing of approved make of manoblock pumpset with flow up to 750LPM and head upto 30m with power upto 2 HP, Make Wilo, Xylem, Grundfos. MPMS20HH 1 Phase (ARTICLE NO. 8054309).

Supply, installing, testing of approved make of horizontal twin pump booster SS impeller, Flow upto 300LPM and head upto 54m. Make Wilo, Xylem, Grundfos. MHIL-5 (ARTICLE NO. 8014982).

Providing and fixing of wooden railing and vertical pillars of sheesham wood having cutting grinding buffing and making culvature whenever reqd. and fitting the same with necessary accusoin including carving and making of mamental grase on the

vectical pillars

Master pillars

Providing and fixing of roof pressed clay tile manglore tiles of 20mm nominal thickness of approved size and as per approved pablern

Providing and fixing of wardrobes/luggage rack/dressing made of 19mm ply board waterproof of M 10 grade and termite proof of make green/centuny/sonear laminated with sunmica from inner side and 1mm thick sunmica from outer side of make green lam/marina lam of 1st standerd including frames channels handles godrej locks hunges etc.

Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil :

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Making soak pit 2.5 m diameter 3.0 meter deep with 45x45 cm dry brick honey comb shaft with common burnt clay (non modular) bricks of class designation 7.5 bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design

15mm cement plaster on the rough side of single or half brick wall finished with a floating coat of neat cement of mix :1 : 3 ( 1 cement : 3 fine sand)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:1½:3 (1 cement :1½ coarse sand: 3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more

Centering and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platforms

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design. In 75x75 mm deep chase.

Providing and fixing Polypropylene septic tanks made in a single moulding and 3 chamber design, salt resistant, non degradable plastic with one inlet for drain and one outlet for soak pit including excavation, fixing etc. complete in all respect (United Make). Type 5 – 6000 Ltrs (Uses 50-60 persons) per day.

Providing and fixing Fibre reinforced (FRP) manhole covers, including fixing and covering, with fitting keys, 2.5 and 5 tonnes load bearing capacities (Everlast Make).

Manhole cover 600x600mm 2.5 tonnes capacity

Manhole cover 450x450mm 2.5 tonnes capacity

Manhole cover 600x600mm 5 tonnes capacity.

Manhole cover 450x450mm 5 tonnes capacity

Surface preparation including cleaning of expansion joint and then

Installation of Hypalon strip thicknees 150mm with epoxy adhosive on both edges

Filling of poly urethane sealant with backup rod

Fixing of Aluminium strips thickness would according to the size of shape of joint

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form work for: Retaining walls, return walls, walls (any thickness) including attached pilasters buttresses, plinth and string course fillets, kerbs and steps etc.

Providing and fixing of wardrbes/dressing of internal steel boxes including partition etc. back and sides 19mm thick ply board shuthers water proof of 710 grade and termite proof of make green/century/soneac laminated with 0.8mm sunmica from inner side and 1mm thick sunmica from outer side of make green lam /marino lam of 1st standred including frames channels, handles godrej locks, stainless skel hunges all complete.

Providing and fixing of base frame for LED Pannel made of 19mm thick water proof and termite proof ply board of 710 grade make green sonear cntury laminated with 1mm sumnica of make green lam marino lam of 1st standred complete.

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete 2nd class teak wood 50 x 20 mm

Providing and fixing wooden moulded corner beading of size 50x50 mm (base and height) of triangular shape to the junction of paneling etc. with iron screws, plugs and priming coat on unexposed surface etc. complete. Second class teak wood

Providing and fixing of wooden shade beams in inlay false ceiling made of 12mm water proof ply of 710 grade make green sonear century veener polish /lamination with 1mm sunmica of make green lam/maroni lam of 1st standred complete.

Providing and fixing of wooden maulding of 2nd class teak wood od size (25mm x 25mm) corner on the inner side of door frame

Engaging carpenter for opening of door/window shuthers for polishing

Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour Two coats

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot &double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Dismantling of manhole including R.C.C. top slab, C.I. cover with frame including stacking of useful materials near the site and disposal of unserviceable materials into municipal dumps within 50 m lead as per directions of Engineer-in-Charge: Rectangular manhole 90x80 cm and 45 cm deep

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 90x80 cm and 60 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm

Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes

75 mm diametre

150 mm diametre

200 mm diametre

Repair of old electric points by way of replacing of wires and witches of 1st standerd

Providing and fixing of 5 star ceiling of make orient/bajaj/khaitan

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement: 3 coarse sand) including making joints with or without grooves (thickness of the joints except at sharp curve shall not to be more than 5mm) including making drainage opening wherever required complete etc. as per direction of Engineer-incharge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and fixing of kitec pipe for internal fitting of bathrooms 6 nos size model

Size No 1640

Size No 3240

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead. For thickness of tiles 10 mm to 25 mm

Providing, fixing and applying plaster of paris (POP) false ceiling consisting of frame work made with 50mm sq M.S tubes of 18 G thickness as main runner at 600 mm C/C both ways, suspended / supported with M.S flats 25x4mm from existing RCC slab including providing and fixing expanded metal of size 5.25mm x 1.25mm thickness welded to main runner and applying POP (calcium sulphate semihydrate variety) to the expanded metal of thickness not less than 10mm finished smooth to line and level including necessary supports scaffolding etc. as required and also including applying a coat of red oxide zinc chromate primer over the M.S frame work and suspenders complete.

Supplying and stacking of good earth at site including royalty (earth measured in stacks will be reduced by 20% for payment)

Supplying and stacking at site dump manure from approved source including carriage complete (manure measured in stacks will be reduced by 8% for payment) Screened through sieve of I.S. designation 4.75 mm

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation

Jaswant Singh

aditya puri

Manohar Singh Sasan