PROVISION OF BATHING POINT AND AREA DRAIN AT ASC CENTRE SOUTH UNDER AGE B/R II IN GE CENTRAL BANGALORE

Amount

B/R PORTION: - Demolition of plain cement concrete (unreinforced) in ground floors, plinth protection/path/pavings etc not exceeding 15 cm thickness. (below or above ground level) and removing debris outside MD land complete all as specified and directed.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation, UG cable, water supply pipe line manhole etc area not exceeding 10 Sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated material to a distance exc. 50 m but not exc 1.5 KM and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

M & L for Plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete for embeding post, struts, etc complete all as specified and directed.

M & L for Plain cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as surface channels and drains complete all as specified and directed.

M & L for extra for forming fair finished to concrete surface of drain 30cm inner girth in cement including forms, mould, mitred/stopped etc complete all as specified and as directed.

Supply and fixing RCC pipe, 300mm bore, class NP-3, laid and jointed with collar complete all as directed.

M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggragate) as in bed to drain pipes and forming cradles against the sides of pipes after they are laid and tested complete for 300 mm bore RCC/PVC/DWC drain pipes complete all as specified and directed.

M & L for Precast Reinforced Cement Concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in cover slab of drain, etc and set in cement mortar 1:4 including necessary form work, moulds, etc complete all as specified and directed by the Engr-in-Charge. (Note : Reinforcement shall be measured and paid separately)

M & L for Reinforced Cement Concrete M-25 nominal mix as in foundation, footings foundation beams, plinth beams etc complete all as specified and directed.

M & L for Reinforced Cement Concrete M-25 nominal mix as in beams, cantilevers, lintel beam etc complete all as specified and directed.

M & L for use & waste Form work to sides of concrete foundations, footings, raft beams, sides and soffits of plinth beams and the similar works for flat rough finished surfaces of concrete complete all as specified and directed.

S & F TMT steel bars 10mm dia and over, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F TMT steel bars 6 to 8mm dia, cut to length, bend to shape required, including cranking, bending spirally as in tie/stirrups of columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for Hardcore of broken/crushed stone aggregate of gauge n.exc 63 mm deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for 75mm thick Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in sub base of floor, etc complete all as specified and directed.

M & L for precast chequered cement concrete tiles of size 30cm x 30cm x 25mm thick, as in floors etc, including 20 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and directed.

M & L for plain cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) for door cill, lintels, steps, copings, apex stones, boundary pillars, paddings, with plain fair faces including chamfering, weatherings, throatings etc and setting in cement mortar necessary form work complete all as specified and directed.

M&L for precast cement concrete block masonry type C1, 1:3:6 (20 mm graded granite stone aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

S & F solid PVC door frames of size 50mm x 47mm made out of 5mm single side prelam PVC sheet shall be used instead of plain colour PVC sheet & edges will be painted to match with prelam PVC sheet reinforced with MS square tube complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet 5mm thick to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, as per specification and drawing and as directed.

S & F 75 mm size, butt hinges, stainless steel with cadmium coated screws complete all as specified and directed.

S & F 125 mm long, Aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and directed.

S & F 125 mm size, Aluminium handles, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

Supplying and laying of 20mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of 25mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S&F 15 mm bore stop valves with wall flange cast copper alloy chromium plated screwed down to iron pipe complete all as specified and directed. Make: CERA Cat NO F8040204 or equvelent of Make Hindware/Parryware/PRAYAG

S&F 15 mm bore bib taps with flange cast copper alloy chromium plated with capstan head screwed down to iron pipe complete all as specified and directed. Make: CERA Cat NO HT-F3001151 or equvelent of Make Hindware/Parryware/PRAYAG

S & F shower rose PTMT with arms with or without swivel joint, 125mm size including fixing to iron pipes complete all as specified and directed. (Make: PRAYAG or equivalent of Polytuff)

S&F towel rail 600 mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats.(Minimum weight 190 gms) complete all as specified and directed. (Make: PRAYAG or equivalent of Polytuff)

S&F Vitreous China Wash hand basin , white flat back size 550x400 mm including a pair of mild steel angle iron brackets duly painted, erected/embeded in wall, including provision of chromium plated fancy type long neck pillar tap with capstan head suitable for 15 mm bore pipe, 32 mm waste coupling brass chromium plated suitable for wash hand basins & 32 mm dia LDPE PVC waste pipe, 45 cm long PVC connections including cutting hole and pinning in ends making good disturbed portion using cement mortar 1:3 complete all as specified & directed by Engineer-in-charge. Make of basin CERA Cat No S2040105 or equivelent of Parryware/Hindware/Prayag

S & F stainless steel soap dish, 150mm, fixed to wall with chromium plated screws complete all as specified and directed. Make : CERA Cat No F5007106 or equivalent of Hindware/Parryware/Prayag

S&F 15 mm bore angle valve PTMT any colour high pressure screwed to iron pipe complete all as specified and directed. Make: PRAYAG or equvelent of Make

S&F 110 mm dia PVC (SWR) pipes, Type 'B', single socketed,in any length with rubber ring joints,laid in trenches or in floors complete all as specified and directed.

S & F 75 mm dia outlet , PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F for pre-painted galvalume aluminum zinc coating (AZ 150) GI based corrugated steel sheet 0.50mm thick (Total coated thickness) of any colour, finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with best quality self tapping screws as specified

S & F Pre-Painted galvalume aluminium zinc coating (AZ 150) GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/valley gutter, fixed with self tapping screws complete all as specified and directed. (Colour of ridge shall be same colour as that of sheet used for roof)

M & L for Mild steel framed work such as grills, gratings, door, gates etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bar, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M & L for Mild steel plate (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-290, Grade E-165 complete all as directed.

S & F Rolled mild steel work as in trusses,purlins, posts etc using Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc including cutting, welding complete. Steel section conforming to Fe-410-W (Gde-E-250) weldable quality-B complete all as specified and directed.

S & F compound girders and sanchions, lattice girders, areial masts, stagging for water tanks and the like including caps, bases, splices etc built up from two or more beams or channels or angles with plates, including all lattice bars stiffeners, gusset plates. Steel section shall conform to Fe-410-W (Gde- E- 250) weldable quqality - A complete all as directed.

M & L for rendering 10 mm thick in cement mortar 1:3 on concrete surfaces as in roof slab/ceilings (sunshed, chajja, fins etc) and finishing surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection laid in proper slope/gradient etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

M & L for joint free non-skid, ceramic, coloured tiles, Grade B II(a), 8 to 10mm thick (square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for glazed ceramic joint free, coloured tiles, 350x250mm/450x350mm, Grade B III, 7 to 8 mm thick as in dado/vertical surface of wall/ skirting including 10 mm thick screed bed in cement mortar 1:3 set & jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles complete all as specified and directed.

E/M PORTION : - (EARTH WORKS AND CONCRETE WORKS IF ANY RELATED TO E/M WORKS SHALL BE MEASURED AND PAID UNDER RESOECTIVE ITEM CATERED IN B/R PORTION) : Point wiring with PVC insulated and unsheathed FRLS cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including PVC rigid non metalic conduit (Medium grade) on surface conforming to IS-9537 with all accessories including fabricated MS terminal boxes fixed flush with wall surface with 3mm thick laminated sheet top cover fixed with brass screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for :- One light or fan point controlled by one 5 Amps switch one way

Supply and fix Switch piano, flush button single pole, 5 Amps one way. Make : Anchor/Cabtree/Legrand/Standard

Supply and fix Ceiling rose surface bakelite 65x50mm three terminals including supply and fix PVC blocks. Make : Anchor/Cabtree/Legrand/Standard

Supply and fix in replacement Sheet metal enclosure (ISI marked) distribution board for 240 volts, SPN 4 way horizontal type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

Supply and fix in replacement MCB single pole & neutral 40 Amps 240 volts, C series,10 kA rupturing capacity

Supply and fix in replacement MCB single pole 6 to 32 Amps 240 volts, C series, 10 kA rupturing capacity

S&F in replacement Pride plus inverter batten of make Havells, LED tube light fitting of 20 watts 6500K , 230 volt, with polycarbonate channel , lithium Ion battery with charging time 8-10 hours and back up time 4 hours complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Havells Cat No LHEXACP7FN1W020 OR equivelant of make Crompton Greaves/Bajaj/Philips/Wipro

M & L for Sand cushioning and covering with clean dry sand in trenches for protection of under ground cables (below, above and around the cable laid in trenches) complete all as specified and directed. (Note: Thickness after punning down shall be measured for payment)

Supply and laying well burnt bricks, locally available best quality bricks laid breath wise across the length of cable in trenches for protection of UG cables complete all as specified and directed.

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, GI strips armoured cable for working voltage 1100 volts, 2 core, nominal cross sectional area of main conductor 16 Sqmm, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, culverts, under floors, through GI Pipe complete all as specified and as directed.

M&L, Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6.0mm thick buried directly in ground (earth pit depth not less than 2.25m deep below the ground level) with top edge of earth plate at a depth not less than 1.5m below ground level connected to earth using GI earth wire of 4 mm dia by means of of nuts, bolts and washer and check nuts of GI or steel as shown in electrical plate No.3 of MES SSR-2009 (Part-I) and connected to earth test point all as specified or indicated including testing on completion with and including 15mm bore light grade GI protection pipe 7.5 metre long for earth including PCC (1:2:4) pit with RCC (1:2:4) type B-1 cover, 40mm thick reinforced with 6mm dia MS bars @ 100mm both ways with lifting hooks made out of 6mm dia MS bars, watering arrangement with 20mm dia light grade pipe, funnel, wire mesh, common salt chorcoal, necessary excavation and earth work in any type of soil complete all as specified.

docileworx

GIRISH M C

B5BUILDING SOLUTIONS

Srisrinivasaenterprises

RK Builders

ShaikPyarejanandsons