Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹33.9 LAccepted-AOC G 124 FLAT NO 4 DILSHAD COLONY DELHI 110095 | SHAHDARA | DELHI | 110095 | L1 | Accepted-AOC Being Lowest | |
| 2 | L2₹39.8 L+₹4.8 L (13.7%)Rejected-Finance N A | NA | NA | 121004 | L2 | Rejected-Finance Being Other Than Lowest |
Tender Value
₹48 L
EMD Value
₹96,000
Closing Date
10 Sept 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE (EAST) DELHI CANTT-10
GE (EAST) DELHI CANTT-10
REPAIR/REPLACEMENT OF JOINERY WORK/COMMON AREA DEVELOPMENT AT MANEKSHAW MD ACCN AREA IN THE AREA OF AGE B/R-I UNDER GE (EAST) DELHI CANTT-10
2022_MES_538319_2
GE/DE-20/2022-23
Open Tender
Civil Works
Item Rate
180 days
GE (EAST) DELHI CANTT-10
Class D cat a (i)
8 documents required · 8 mandatory
₹500
Yes
GE (EAST) DELHI CANTT-10
₹96,000
Yes
10 Nov 2022
17 Aug 2022
12 Sept 2022
17 Aug 2022
10 Sept 2022
27 Aug 2022
Amount
Taking down Chowkats or frames from the opening of size not exceeding 1.5 sqm each with shutters ( without taking off shutters from the frames) complete all as specified and as directed by Engr-in-Charge.
All as per Srl item No 1 above but size of opening exceeding 1.5 Sqmtr but not exceeding 4 Sqmtr complete all as specified and as directed by Engr-in-Charge.
Taking down shutters of any description exc 1.00 sqm & nexc 2 sqm each complete all as specified and as directed by Engr-in-Charge.
Dismantling boarding , any description , fixed in any position with nails complete all as specified and as directed by Engr-in-Charge.
Dismantling wrought iron or mild steel work of any description complete all as specified and as directed by Engr-in-Charge.
S&F Plain , solid , straight chowkhats and frames of 2nd class hard wood, wrought , framed rebated on the solid , rounded or chamfered , put together with glue, pinned at joints complete all as specified and as directed by Engr-in-Charge.
S&F MS framed work as in door or gates of angle or other section with gusset plates,rail, braces,etc and similar work conforming to Fe 290 (Gde E-165) quality 'B' complete all as specified and as directed by Engr-in-Charge.
M&L providing cement concrete type B1 1:2:4 (20 mm graded aggregate) as in roof kerbs or mud stops, hold fast, rounded or chamfered, water trough and the like including weathering slightly rounded or chamfered angle and throating as directed complete all as specified and as directed by Engr-in-Charge.
S&F 35mm thick 2nd class hard wood glazed and skeleton shutters open rebated prepare to receive glass, gauge etc edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass, gouge etc size of members of shutters as specified in SSR Part-I Sec-8 clause 8.24(a) complete all as specified and as directed by Engr-in-Charge.
S&F 35mm thick flush shutter, solid core construction, with block board core and plywood face panel commercial type on both sides complete all as specified and as directed by Engr-in-Charge.
S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and as directed by Engr-in-Charge.
S &F Factory made solid panel PVC door shutter 30 mm thick (style) con-sisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, in the frame at site as per specification & drawing complete all as specified and as directed by Engr-in-Charge.
S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified and as directed by Engr-in-Charge.
S&F 100mm long butt Hinges, medium weight, cold rolled mild steel complete all as specified and as directed by Engr-in-Charge.
S&F 300mm long aluminum alloy anodized sliding door bolt with hasp and staple(bolt type)and fixing clips of sheet cast sec and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fixed complete all as specified and as directed by Engr-in-Charge.
S&F 150mm long aluminum anodized barrel tower bolt of cast aluminiun alloy section and fixed complete all as specified and as directed by Engr-in-Charge.
S&F in repair 150mm long aluminum anodized barrel tower bolt of cast aluminiun alloy section and fixed complete all as specified and as directed by Engr-in-Charge.
S&F Aluminium handles, 150mm size cast type anodised complete complete all as specified and as directed by Engr-in-Charge.
S&F in repairs Aluminium handles, 150mm size cast type anodised complete all as specified and as directed by Engr-in-Charge.
S&F in repairs for mild steel 300 mm long, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed by Engr-in-Charge.
S&F Floor door stoper of aluminium alloy body and tongue, anodised with hard drawn steel spring overall length of cover plate 140mm.
S&F in repair Floor door stoper of aluminium alloy body and tongue, anodised with hard drawn steel spring overall length of cover plate 140mm.
S&F powder coated aluminium frame for ventilators, doors with one or more rebated incl jointing cleats for fixing etc complete all as specified and as directed by Engr-in-Charge. (Note : The work will be executed at High rise bldgs and necessary provision for T&P, scaffoling and safety measures etc is deemed to be included in unit rate quoted by the tenderer for the same.)
S&F powder coated three track aluminium (glazed/ gauged) window shutters sliding type without AC opening incl 3mm thick glass and stainless steel wiremesh, (02 shutter with glass, and 01 with wiremesh) without sash bar aluminium saction weighting 0.55 Kg per mtr including necessary joining cleats, glazing clips, rubber packing, anodised aluminium beading , sliding channel,roller screws including frame/fittings complete all as specified and as directed by Engr-in-Charge. (Note : The work will be executed at High rise bldgs and necessary provision for T&P, scaffoling and safety measures etc is deemed to be included in unit rate quoted by the tenderer for the same.)
S&F powder coated three track aluminium (glazed/ gauged) window shutters sliding type with AC opening(with shutter) incl 3mm thick glass and stainless steel wiremesh, (02 shutter with glass, and 01 with wiremesh and balance portion with fix glass) without sash bar aluminium saction weighting 0.55 Kg per mtr including necessary joining cleats, glazing clips, rubber packing, anodised aluminium beading , sliding channel,roller screws including frame/fittings complete all as specified and as directed by Engr-in-Charge. (Note : The work will be executed at High rise bldgs and necessary provision for T&P, scaffoling and safety measures etc is deemed to be included in unit rate quoted by the tenderer for the same.)
S&F powder coated aluminium window and ventilator shutters, side hung type with out sash bars, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long ( 1 No.) hinges type B-21 100 mm long (2No.) ,aluminium tower bolt 100 mm long (2No.),suitable handle (1 No.) complete all as specified and as directed by Engr-in-Charge. (Note : The work will be executed at High rise bldgs and necessary provision for T&P, scaffoling and safety measures etc is deemed to be included in unit rate quoted by the tenderer for the same.)
S&F Sheet glass, 5.5 mm thick ordinary quality, in squares, not exceeding 0.50 sqm in each pane including beading fixed with nails complete all as specified and aas directed by Engr-in- Charge.
S&F stainless steel wire cloth, 0.36 mm nominal dia. of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or stainless steel wire staples complete all as specified and as directed by Engr-in-Charge.
S&Faluminium anodized grills with 6mm x 5mm aluminium section having square gap of 100mm thick with fixing arrangement complete all as specified and as directed by Engr-in-Charge.
Stainless Steel (SS-304) perforated Cutlary basket (6161/6160) product code made of min 4mm dia stainless steel wire and bottom of S S perforated sheet (sheet grade 304) approved quality with suitable arrangement for fixing telescopic basket over and including telescopic channel 18 inches/20 inches in length two way extruded MS galvanised over rollers as approved by Engr-in-Charge. (Make: Godreg Cat Part No 6132 or IPSA/ Hettich as approved by Engr-in-Charge.
Stainless Steel thali basket of size (6163/6164) made of min 4mm dia stainless steel wire (sheet grade 304) approved quality with suitable arrangement for fixing telescopic basket over and including telescopic channel 18 inches/20 inches in length two way extruded MS galvanised over rollers as approved by Engr-in-Charge. (Make: Godreg Cat Part No 6136 or IPSA/ Hettich as approved by Engr-in-Charge.
Stainless Steel basket (plain) of product code (6120/6121) made of min 4mm dia stainless steel wire (sheet grade 304) approved quality with suitable arrangement for fixing telescopic basket over and including telescopic channel 18 inches/20 inches in length two way extruded MS galvanised over rollers as approved by Engr-in-Charge. (Make: Godreg Cat Part No 6121 or IPSA/ Hettich as approved by Engr-in-Charge.
S&F 150mm stainless steel handle, polished bright complete all as specified and as directed by Engr-in-Charge.
Providing & Fixing of factory made kitchen cupboards (lower and upper unit) made up 18 mm thick HDHMR Board (Century/Action Tesli/ Kitply) with both side comany pasted (any colour) mild and 10mm HDHMR board with white colur on both sides. Front shutter/partitions shall be made of machine cut18mm MDF board with laminates (merino/century/kitply) duly lipping (edge bending) complete all the factory with G Profile handle of approved colour and soft closing hinges (Hettich/ Godrej/ IPSA). (Note: No edge bending will be allowed at the site (Measurement shall be of face only)
Providing & Fixing 18mm thick MDF board with approved lamination all machine cut & pasted, lipped (edge bending) factory made used as shutter along with all soft close hardware (Hettich) required and frame to cover area under WHB/ Sinks as directed on ground.
S&F in repair aluminium door seal brown/white coated with PVC brush or PVC flexible door rubber fitted in bottom of door complete all as specified and as directed by Engr-in-Charge.
M&L preparation of surfaces and applying two coats of synthetic enamel painting over a coat of red oxide primer on new steel surfaces of any description over 10 cm in width or girth not otherwise described.
M&L preparation of surfaces and applying two coats of synthetic enamel painting over a coat of pink primer on new wooden surfaces of any description over 10 cm in width or girth not otherwise described.
Hacking out old brocken glass (any thickness , size , quality or description) from wooden/metal frames or stone, concrete or brick surrounds , glazed with putty or fixed with beads complete all as specified and as directed by Engr-in-Charge. (Note : The work will be executed at High rise bldgs and necessary provision for T&P, scaffoling and safety measures etc is deemed to be included in unit rate quoted by the tenderer for the same.)
S&F 3mm thick Sheet glass, ordinary quality and glazing with oil putty/wooden beading in square n exc 0.5 sq.m. in each pane complete all as specified and as directed by Engr-in-Charge.
All same as per serial item No 41 here-in-before but figured glass pin head type complete all as specified and as directed by Engr-in-Charge.
S&F 4mm thick Sheet glass, ordinary quality and glazing with oil putty/wooden beading in square exc 0.5 sq.m. in each pane complete all as specified and as directed by Engr-in-Charge.
Taking down cement or cement lime plaster on brick walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed by Engr-in-Charge.
M&L for rendering 15mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surface and finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.
M&L for rendering 15 mm thick rendering fair faces of brick work or concrete surfaces on walls in CM 1:4 finishing even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.
M&L for prepration of newly plastered surfaces of wall and applying two coats of weather proofing exterior acrylic emulsion paint premium quality on wall surfaces over one coat of primer from the same manufacturer complete all as specified and as directed by Engr- in-charge.
M&L for applying two coats of acrylic emulsion interior grade over one coat of primer on newly plastered surfaces of wall including preparation of surface complete all as specified and as directed by Engr-in-Charge.
M&L for applying two coats of interior acrylic emulsion paint of premium quality over one coat of primer and 1mm thick wall putty on old surfaces of wall duly prepared after complete removal of existing treatment by mechanical or manual method complete all as specified and as directed by Engr-in-Charge. (Note : (i) The work will be executed at High rise bldgs and necessary provision for T&P, scaffoling and safety measures etc is deemed to be included in unit rate quoted by the tenderer for the same. (ii) Work shall be executed through authorised applicator of the manufacturer firm as approved by GE. (iii) Preparation of surfaces shall be got approved from GE before applying finishes.)
M&L for applying one coats of acrylic emulsion paint (interior) on old surfaces of ceiling incl preparation of surface complete all as specified and as directed by Engr-in-Charge. (Note : The work will be executed at High rise bldgs and necessary provision for T&P, scaffoling and safety measures etc is deemed to be included in unit rate quoted by the tenderer for the same.)
M&L preparation of old painted surfacecs of wood and wood based materials of any description not otherwise described over 10cm width or girth and and applying one coat of synthetic enamel paint complete all as specified and as directed by Engr-in-Charge.
M&L preparation of old painted surfaces of steel of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed by Engr-in-Charge.
S&F in repairs Drapery rod 25mm dia aluminium, powder coated teak wood texture finish 1 mm thick, with end bulbs as reqd, fixing brackets complete all as specified and as directed by Engr-in-Charge.
S&F in repairs Drapery rod 25mm dia stainless steel pipe with steel finish 1 mm thick incl steel end bulbs, steel brackets etc incl connected items complete all as specified and as directed by Engr-in-Charge.
S&F in repairs galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and as directed by Engr-in-Charge.
Providing services related to welding in repairs and blacksmith work based on day to day complaints on all working days (except Sunday and gazetted Holiday ) from 0900 hours 1700 hours complete all as specified and as directed by Engr-in-Charge. (Note- 1. The above task shall be carried out by deploying minimum 01 welder having black smith skills and 01 Helper on daily basis. 2. Necessary T&P, ladders, minor consumable viz welding rods/extras, equipments and safety measures shall be provided by the contractor. 3. All replaceble material shall be issued from MES store.
M&L in replacement tiles any type/size and thickness in patches, area n exc 5 sq.m. including taking out old screed/rendering and proving new base in lieu , and laying or setting, jointing and pointing in while or coloured cement so as to match the existing tile work complete all as specified and as directed by Engr-in-Charge.
M&L for filling glass putty to old/existing window glass panes n exc 0.5 sqm each incl removal of old loose glass putty complete all as specified and as directed by Engr-in-Charge. (Note : The work will be executed at High rise bldgs and necessary provision for T&P, scaffoling and safety measures etc is deemed to be included in unit rate quoted by the tenderer for the same.)
Taking up or down existing steel rolling shutters area exc. 4.00 Sqm but n exc. 9.00 Sqm each in any position and description and removing from site of work complete all as specified and as directed by Engr-in-Charge.
S&F Steel rolling shutters with sheet thickness of laths 1.25mm without ball bearing , as specified including top cover , anchoring rod,springs, hasp and staple and one shop coat of primer; erected in position as indicated ; push pull or manual type including making good to dismantelled portions complete all as specified and as directed by Engr-in-Charge.
M&L for repair to existing steel rolling shutters area exc. 4.00 Sqm but n exc. 9.00 Sqm each by repairing/ welding/ oiling/ greasing to anchoring rod,springs,side guide channel etc incl dismantling existing steel rolling shutters of any width and refixing after making serviceable after adjusting springs complete all as specified and as directed by Engr-in-Charge.
S&F 1.25mm thick plain black steel sheet in hearths; covering to door shutters; covering to door/chowkats (frames);chullah hoods; water tanks; water troughs;ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required incl priming complete all as specified and as directed by Engr-in-Charge.
M&L for 10mm thick cement plaster on brick or concrete surfaces, as in ceiling/ facia/ chajja etc. in cement mortar 1:3 finished even and smooth without using extra cement, all as specified (Note : The work will be executed at Highrise bldgs and necessary provision for T&P, scaffoling and safety measures etc shall deemed to be included in unit rate quoted by the tenderer for the same.)
Taking down cement plaster/ duster bed PCC of Column, Chajja, Parapets of roof, Facia, Drops, Ceiling etc and making good with cement plaster 10mm thick in CM 1:3 with PCC 1:2:4, (average thickness of PCC 25mm) aas required, brushing neat cement slurry with 3.0Kg of cement per Sqm incl necessary form work and scaffolding upto 9th floor incl fixing of wire netting where required to match the existing surfaces complete all as specified. (Note : The work will be executed at Highrise bldgs and necessary provision for T&P, scaffoling and safety measures etc shall deemed to be included in unit rate quoted by the tenderer for the same.)
Vipul Construction
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .