CA NO. CWE SGNR-11 OF 2020-21 SPECIAL REPAIRS TO BUILDING NO. P-10/01 TO 04 (JCO MARRIED ACCOMMODATION) AT MILITARY STATION SRI GANGANAGAR

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding and rubbish off the premises complete all as specified and directed by Engineer - in - Charge.

Demilitionof mud in roofs, any thickness,including plastering and leeping complete all as specified and directed by Engineer-in-Charge

M& L for wire brushing and cleaning top surface of roof or cement concrete and applying evenly a tack coat of insustrial bitumen 85/25 at the rate of 1.20 Kg Per Sqm complete all as specified and directed by Engineer-in-Charge.

M&L for polythene film, 150 micron thick, laid on a coat of bitumen primer @ 0.30 to 0.50 Kg / Sqm complete all as specified and directed by Engineer-in-Charge.

M&L for 80mm thick lime concrete teracing as specified in roof complete all as specified in MES Chedule Part - I and Part - II complete all as specified and directed by Engineer-in-Charge.

M&L for 40mm thick brick tiles laid on cement mortar and joints grouted flush in cement mortar (1:3) mixed with 5% crude oil by weight of cement on mud phuska complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 06 here-in-before but for except brick tiles complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding and rubbish off the premises complete all as specified and directed by Engineer - in - Charge.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in floor etc set and jointed in cement slurry and pointed in white cement mixed with pigment to match the shade of tiles over and including 15 mm thick screed in CM 1:4 complete all as specified and directed by Engineer - in - Charge.

M&L glazed ceramic coloured tiles, 600x450x8mm thick as on vertical surfaces like dados or skirting over 15mm thick rendering in CM 1:4, set & jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

M&L for Vitrified coloured light shade Ceramic tiles 10 mm thick (square / rectangular) polished area of each tiles not exc 0.36 sqm , over 15 mm thick screed bed CM 1:6,in floors etc set and jointed in neat cement slurry and pointed in white cement slurry and pointed in white cement or coloured cement to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

Demolition concrete in ground floors and pavings not exceeding 15cm thickness (below or above ground level) complete all as specified and directed by Engineer - in - Charge.

M&L for machine cut Kota stone slab flooring 20-25mm thick over cement screed base 15 mm thick in cement mortar 1:6 laid and jointed withgrey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including Mirror Polishing finishing complete all as specified and directed by Engineer - in - Charge.

M&L for machine cut Kota stone slabs as in vertical surfaces such as risers of steps 10-25mm thick over cement screed bas laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, mirror polishing also moulding edges including 10mm of backing coat in CM 1:4 aggregate complete all as specified and directed by Engineer-in-Charge.

M&L for 20 mm thick Black granite table moulded and polished machine cut in jambs,pillars ,skirting / dado, shelves etc laid over 15 mm thick cement mortar 1:3 screed set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing polishing complete all as specified and directed by Engineer - in - Charge.

Demolitionof brick work built incement mortar of any descirption complete all as specified and directed by Engineer-in-Charge.

M&L brick work with fly ash bricks old size, streight or curved on plan exceeding 6m mean radius, built in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 17 here in before but for exceipt bricks complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick or stone walls etc. including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer - in - Charge.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces of wall in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces of wall in cement mortar (1:4) finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 5mm thick on fair faces of brick or concrete surfaces as on ceiling in in cement mortar (1:3) finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered or unplastered surface of walls and applying three coats of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of new plastered or unplastered surface of ceiling and applying three coats of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old plastered or unplastered surface of ceiling and applying two coats of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of new plastered or unplastered surface of walls and applying two coats of cement based paint over a coat of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old surface of walls and applying two coats of cement based paint after complete removal of existing treatmentment complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old decorative surfaces of walls, and chalk whiting as preparatory to distempering and applying two coats of oil bound distemper (OBD) complete all as specified and directed by Engineer - in - Charge.

M&L for two coats of oil bound distemper over wall putty over a coat of primer on newly plastered surfaces including preparationof surface complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted wooden surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of old painted steel surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer - in - Charge.

Taking down chowkhats or frames (without taking off shutters from the frames) not exceeding 1.5sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down chowkhats or frames (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down chowkhats or frames (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 sqm each and refixing the same in same opening each complete all as specified and directed by Engineer - in - Charge.

S&F for MS flat iron 25x6mm as in hold fast conforming to Fe-290 Gde E-165 complete all as specified and directed by Engineer-in-Charge.

Cutting holes into brick wall n exc half brick wall for inserting hold fast in CM and making good in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate complete all as specified and directed by Engineer-in- charge.

S&F for framed brackets of angles or tee with web and flange cut to shape, drilled and counter shunk for screw, including bending and welding angles as necessary gusset plates riveting rails, braces, running rails and guides and hanging also fastening and fixing complete conforming to Fe-290 Grade-165 complete all as specified and directed by Engineer-in-Charge.

S & F for pressed steel door frames with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., size of frame 105x60mm complete all as specified and directed by Engineer - in - Charge.

Taking down steel windows / ventilators of any description complete all as specified and directed by Engineer-in-Charge.

S&F for steel ventilator with top hung shutter including hinges, steel peg stay with glazing bars complete all as specified and directed by Engineer-in-Charge.

S&F for steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed by Engineer-in-Charge.

S&F for 10mm dia MS round guard bars for steel windows complete all as specified and directed by Engineer-in-Charge.

S&F for MS handle (left / Right) for fixing in steel window with complete accessory complete all as specified and directed by Engineer-in-Charge.

Supply & fix 35mm thick, factory made glazed and skeleton shutter of 2nd class hard wood open rebated and prepared to receive glass, gauge etc, without sash bars, edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc. Sizes of members as specified in SSR Part-I, Section 8.24 (a) and fitted to chowkhats complete all as specified and directed by Engineer-in-Charge.Note :- The species of timber shall be Hollock/Bonsom.

S&F 35mm thick, factory made plain framed panelled (two panels) shutters of 2nd class hard wood with lock rail and panel inserts of 9mm thick BWP commercial ply or 12mm thick veneered particle board flat pressed three layered conforming to IS-3097 exterior grade-I type- I duly ISI marked general purpose commercial veneered on both side bonded with (BWR) type phenol formaldeyde synthetic resin-adhesive, the size of rails and styles as per IS-1003 Part-I, Kiln seasoned and chemically pressure treated including one shop coat of pink primer complete all as specified & directed by Engineer-in-Charge Note :- The species of timber shall be Hollock/Bonsum

S & F for Fiber Glass Reinforced plastic (FRP) Door Frames of three legged of cross section 90mmx45mm having single rebate of 32mmx15mm to receive shutter of 30 mm thickness. The laminate door frame molded with fire retardant grade unsaturate polysteres in and chopped mat.Doorframe laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiberglass from all sides MS stay shall be provided at the bottom to steady the frame complete all as specified and directed by Engineer - in - Charge.

S & F for 30mm thick glass fiber reinforced plastic (FRP) paneled door shutter of required color and approved brand and manufacture made with fire retardent grade unsaturated polyster resin moulded to 3mm thick FRP laminated for forming hollow rails and style with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings cast monolithically with 5mm thick FRP laminate for panels for conforming to IS:14856-2000 complete all as specified and directed by Engineer - in - Charge.

S&F for mild steel butt hinges “medium weight” 100mm long cold rolled mild steel complete all as specified and directed by Engineer - in - Charge.

S&F for aluminium handle cast type anodized, 150mm long complete all as specified and directed by Engineer-in-Charge.

S&F for 125mm aluminium anodized barrel tower bots of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

S&F for 300mm long aluminium alloy anodised sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed by Engineer-in-Charge.

S&F for aluminium anodized barrel tower bolts of extruded section 150mm long complete all as specified and directed by Engineer-in-Charge.

M&L two coat of synthetic enamel paint on wooden surfaces (ordinary tint) over new surface over 10cm width or girth including preparation of surface complete all as specified and directed by Engineer - in - Charge.

M&L two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide on steel surface over 10 cm width or girth, not otherwise described including preparation of new steel surface complete all as specified and directed by Engineer - in - Charge.

S&F for stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm complete all as specified and directed by Engineer - in - Charge.

S&F4 mm thick figured glass pin head type and glazing with oil putty in squares n.exc 0.50 sqm each complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with oil putty or fixed with beads complete all as specified and directed by Engineer-in-Charge.

S&F for harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. compelte all as specified and directed by Engineer-in-Charge.

Taking down eaves gutter or rain water pipes (any size or pattern) including all fittings, heads, shoes, bends, swan necks etc complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints, to walls including all fittings, heads, shoes, bends, swan necks complete all as specified and directed by Engineer-in- charge.

Taking up or down for 15 mm bore steel water tubing galvanised with connection including cleaning for refixing complete all as specified and directed by Engineer - in - Charge.

Taking up or down for 20mm bore steel water tubing galvanised with connection including cleaning for refixing complete all as specified and directed by Engineer - in - Charge.

Taking up or down for 25mm bore steel water tubing galvanised with connection including cleaning for refixing complete all as specified and directed by Engineer - in - Charge.

S&F for steel water tubing galvanised 15mm bore, “medium grade” with all fittings and fixed to walls and ceiling or in floor complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No. 65 here-in-before but for fixing only with new fittings Old GI tubing as retrieved from respective item of BOQ complete all as specified and directed by Engineer - in - Charge.

S&F for steel water tubing galvanised 20mm bore, “medium grade” with all fittings and fixed to walls and ceiling or in floor complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No. 67 here-in-before but for fixing only with new fittings Old GI tubing as retrieved from respective item of BOQ complete all as specified and directed by Engineer - in - Charge.

S&F for steel water tubing galvanised 25mm bore, “medium grade” with all fittings and fixed to walls and ceiling or in floor complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No. 69 here-in-before but for fixing only with new fittings Old GI tubing as retrieved from respective item of BOQ complete all as specified and directed by Engineer - in - Charge.

S&F in repairs, for rotational moulded polyethylene water storage tank 1000 ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engineer - in - Charge. Note : PVC tanks shall having three layers

S&F 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms) complete all as specified and directed by Engineer-in-Charge.

S&F in repair, vitreous china squatting pan "ORISSA" pattern white, of size 580x440mm with integral foot rest, CI 'P' trap etc complete all as specified complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, PVC low level flushing cistern 10 lirs capacity, valve-less, syphonic action type, white, with inlet, ball valve, float, and handle including brackets, including 32mm bore flush pipe of polyethylene of low or high density of PVC complete all as specified and directed by Engineer - in - Charge.

S&F in repairs, vitreous china wash hand basin counter shank with green / black granite slab to be cut and polished at site as per requirement and approved by Engineer-in-Charge, including brackets, 32mm bore brass chromium plated waste coupling, pillar cock (fancy type and 32mm bore low density polythelene (LDPE) flush pipe of pressure 6Kgf/Sqm (1.00Mtr long) including 15mm bore 450/600mm length PVC connections complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, soap dish, vitrious china white complete all as specified and directed by Engineer-in-Charge.

S&F in repairs cromium plated shower rose of size 125mm with or without shivel joints as specified including fixing to pipe or union complete all as specified and directed by Engineer - in - Charge.

S&F for 75 mm bore PVC (SWR) multi floor trap with grating including jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

S&F for CP towel rail 600mm long fixed with CP brass screws complete all as specified and directed by Engineer-in-Charge.

S&F in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers, wastes jali and a plain waste pipe of 600mm length including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm complete all as specified and directed by Engineer-in-Charge

S&F in repairs, stainless steel plate rack of size 24'' x 30'' x 10'' made out of 0.6mm thick stainless sheet of first quality complete all as specified and directed by Engineer-in-Charge.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engineer - in - Charge.

M&L for providing cement concrete 1:3:6 type C1 for filling in pressed steel frames and PCC blocks for hold fasts complete all as specified and directed by Engineer-in-Charge.

S&F in repair 15 mm fancy type chromium plated Angle valve/stop valve, screwed down high pressure,with crutch or butterfly handle scresed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engineer-in-Charge

S&F in repair 20mm dia stop valve cast copper alloy, with crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipe complete all as specified & directed by Engineer-in-charge.

S&F in repair 25mm dia stop valve cast copper alloy, with crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipe complete all as specified & directed by Engineer-in-charge.

S&F in repair 15mm dia stop valve cast copper alloy with crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipe complete all as specified & directed by Engineer-in-charge.

S&F in repair 15mm dia bib taps cast copper alloy, chromium plated, fancy type with crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipe complete all as specified & directed by Engineer-in-charge.

S&F in repair Grating doom 100mm dia PTMT (minimum weight 25gms) complete all as specified and directed by Engineer - in - Charge.

Dismantling cast iron or reinforced concrete drain pipes jointed in cement mortar and taking out of tenches complete all as specified and directed by Engineer-in-Charge.

S&F for 75mm dia cast iron soil waste pipe and vent pipes in any length with or without ears in cement joint laid in trenches or in floors complete all as spcified and directed by Engineer-in-Charge.

S&F for 100mm dia cast iron soil waste pipe and vent pipes in any length with or without ears with cement joints laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge.

S&F for 100mm dia cast iron soil waste pipe and vent pipes in any length with or without ears with cement joints fixed to walls complete all as specified and directed by Engineer-in-Charge.

S&F for 75mm dia cast iron soil waste pipe and vent pipes in any length with or without ears with cement joint fixed to walls complete all as specified and directed by Engineer-in-Charge.

S&F for 75mm bore dia CI bends (any radius) diminishing pieces or tapers complete all as specified and directed by Engineer-in-Charge.

S&F for 100mm CI bends (any radius) with duck foot or heel rest complete all as specified and directed by Engineer-in-Charge.

S&F for 100mm CI branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) complete all as specified and directed by Engineer-in-Charge.

S&F 75mm CI branch pieces, single (equal or unequal) oridanary or inverted (spigot or socket type) complete all as specified and directed by Engineer-in-Charge.

S&F 75mm CI branch pieces, double (equal or unequal) oridanary or inverted (spigot or socket type) complete all as specified and directed by Engineer-in-Charge.

S&F for 100mm CI branch pieces, double (equal or unequal) ordinary or inverted (spigot or socket type) complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm tick cement concrete type C-1 1:3:6 using 20mm graded aggregate as in plinth protection complete all as specified and directed by Engineer-in-Charge.

M&L for 40mm thick cement concrete type B1 1:2:4 using 20mm graded aggregate as in flooring, finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (re-inforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge.

M&L for re-inforced cement concrete type B1, 1:2:4 using 20mm graded aggregate in RCC for chajja, parapit wall slab etc. complete all as specified and directed by Engineer-in-Charge.

M&L TMT bars as in reinforcement Fe-500D 10 mm dia and over cut to length bent to shape required incl cranking bending spirally for hooping for cols, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia using TMT bars complete all as specified and directed by Engineer-in-Charge

M&L TMT Bars of 6mm to 8mm dia,cut to length,bent to shape required including cranking, binding spirally for hooping for columns hooking ends and biniding with and including MS wire (annealed) not less than 0.9 mm dia or securining with clip complete all as specified and directed by Engineer-in-Charge

Demolition of cement concrete (unreinforced) any description and any positionfor sunken portion (below or above ground level) complete all as specified and directed by Engineer-in-Charge.

Material and Labour for water proofing treatment to RCC sunken slab as specified below asd as directed by engr-in-charge:- (a) 15mm plaster in CM 1:3 with WPC on raised vertical surface. (B) Cleaning the surface with wire brush/coir brush, removing loose material like dust particles ,dirt etc. (c) Creating fillet covering of 50x50 mm with polymer modified mortar on the junction of slab and walls (d) Apply first coat of two component modified polymer coating on the horizontal and vertical surfaces. (e) Provision of glass fibre mesh of 2x2 mm immidiately on above coating (f) Apply second coat of two component modified polymer coating after 72 hours (g) Laying concrete 1:4:8 over the coating as per requirement (h) Joining the sanitary pipe with non shrink cementatiuos grout (k) Complete the treatment to be carried out by authorised applicator of waterproofing manufacturer Make :- Dr. Fixit/Fosroc/BASF/STP NOTE : (i) The Treatment shall be carried out as per the manufacturers industreis and as directed by eng-in-charge. (ii) The plan area of floor shall be consider for payment. (iii) WPC shall be measured and paid saperately.

M&L for PCC 1:5:10 type E2 using 40mm graded stone aggregate as in foundation, filling and mass concrete or filling in sunken floor complete all as specified and directed by Engineer-in-Charge.

M&L for second class clean swan hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue, pinned at joints, supplied and fixed in scantling and or frame etc. complete all as specified and directed by Engineer-in-Charge.

Dismantling timber scantling 40 Sqcm and over in section, in any position in framed work complete all as specified and directed by Engineer-in-Charge.

S&F for continuous piano hinges, mild steel, bright finish or electrogalvanized width of flaps 30mm which open complete all as specified and directed by Engineer-in-Charge.

S&F in repairs prelaminated particle board, 19mm thick interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work complete all as specified and directed by Engineer-in-Charge.

Taking down carefully copper/aluminium point wiring (light, fan, socket, bell or power) complete including fittings such as switches, ceiling roses, pendent holders, light fittings any type, sockets, regulators etc and making good disturbed surfaces of walls and floors etc to match with the existing surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring complete with 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable drawn in and including concealed PVC rigid conduit pipe medium grade 20mm dia using pipe hooks, elbows, junction covers and junction boxes including provision of 1.2mm thick pressed steel sunken terminal boxes 60mm deep, suitable length and painted with red oxide primer for mounting switches, sockets, fan regulators covered with and including 3mm thick bakelite plastic laminated sheet top cover fixed flush with wall using brass screws & cup washers including 1.5 Sqmm PVC insulated solid / multi standard copper conductor wire as earth continuity to common earth and connecting to earth dolly for one light point controlled by one switch, bell push or one fan point controlled by one switch and making the good of disturb surface of wall with CM 1:3 with white wash or existing colour complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No 116 here in before, but for one switch socket combination 5/6 Amps on independent board complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No 116 here in before, but for one 3 pin socket outlet 5 Amps on same board with other switches complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No 116 here in before, but with multi-stranded copper conductor FRLS PVC unsheathed cable of cross sectional area 2.5 Sqmm for one switch socket combination 6 pin, 15 Amps on independent board including 2.5 Sqmm PVC insulated solid / multi standard copper conductor wire as earth continuity to common earth dolly complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No 116 here in before, but for one light point controlled by two 2 way swiches complete all as specified & directed by Engineer-in- Charge.

All as per Srl item No 116 here in before, but for call bell point complete all as specified & directed by Engineer-in- Charge.

S&F switch piano flush type single pole one way 5/6 Amps, 230 volts complete all as specified & directed by Engineer-in- charge.

S&F switch piano flush type single pole two ways 5/6 Amps, 230 volts complete all as specified & directed by Engineer-in- charge.

S&F bell push flush type 5 Amps complete all as specified and directed by Engineer-in-Charge

S&F switch socket combination 5 Pin, 5/6 Amps flush type complete all as specified and directed by Engineer-in-Charge.

S&F switch socket combination 6 Pin, 5/15 Amps flush type complete all as specified and directed by Engineer-in-Charge.

S&F socket outlet 5 Pin, 5 Amps flush type complete all as specified and directed by Engineer-in-Charge.

S&F ceiling rose polycarbonate surface bakelite 65 x 50mm size three terminals complete all as specified and directed by Engineer-in-Charge.

S&F electronic bell ding dong type, AC 230 Volt single pole complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of existing light fittings with batton integrated LED channel 20 Watt (integral sleek extruded polycarbonate body LED with white acrylic cover) tube light fittings wall mounted complete with rod driver and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2mm upto ceiling rose / connector complete all as specified and directed by Engineer-in-Charge. Make : Havells Cat Part No. LUMILINEPLUSBS20WLED865SPCSS, Bajaj Cat Part No. BCLSBAL20W CW, Crompton Cat Part No. CCS-100-20-65/HL2-DP-NWH

S&F angle holder insulated body with back plate for conduit fittings complete all as specified and directed by Engineer-in-Charge.

S&F for LED lamp 9W for angle holder complete all as specified and directed by Engineer-in-Charge.

S&F in replacement water tight bulk head fittings, comprision of connector galvanized cast iron back plate, wheather proof enamelled gallery, glass well and including 10 Watt LED lamp complete all as specified and directed by Engineer-in-Charge. Make : Havells Cat Part No. HEXAFT10WLED857SSYMBOPC, Bajaj Cat part No. BIBWP10W LED, Crompton Cat Part No. LBHP-10-CDL

S&F in repairs, compact and decorative energy efficient LED mirror light fitting with antiglare diffuser and decorative end caps suitable for 1 x 10 watt fitting 2 Ft version including LED lamp 10 Watt complete all as specified and directed by Engineer-in-Charge. Make : Havells Cat Part No.LUMILINEPLUSBS10WLED865SPCSS, Bajaj Cat Part No. BCLSB 10 WH, Crompton Cat Part No. LDL-10-CDL

S&F stepped type, single socket fan regulator for ceiling fan 1200mm / 1400mm sweep complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of sub-main wiring with two runs of single core cables PVC insulated and un-sheathed 6 sqmm (Nominal Area) FRLS stranded copper conductor drawn into and including PVC concealed conduit, including one run of 6 Sqmm (Nominal Area) copper cable as earth continuity conductor including necessary connections, PVC flexible pipes are used in panel board while connecting the cable complete all as specified and directed by Engineer-in-Charge. Note : Two runs of 6 Sqmm single core cable and one run of 6 sqmm copper wire earth continuty conductor and conduit with fittings shall be measured as one length.

S&F in repairs factory made sheet metal enclosure for double door distribution board made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 8 way, 240 Volts, ISI Marked, 200 Amps bus bar stove enameled dust and vermin proof suitable for incorporation of MCBs and Isolators etc. complete all as specified & directed by Engineer-in-Charge.

S&F in repairs, sheet metal enclosure for double door vertical DB made out of CRCA mild steel sheet surface with insulated material like polyster with epoxy powder coated surface mounted TPN 4 ways, 415 Volts, ISI marked, 250 Amps bus bar stove enameled dust and vermin proof suitable for incorporation of MCBs and isolators etc. complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, MCCB TP & N suitable for 415 Volts, AC supply 63 Amps, with over load and short circuit protection and rupturing capacity not less than 16 KA complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, MCB 'B' series type suitable for 240 volts, AC supply, 5 to 40 Amps, SP & N with over load and short circuit protection and rupturing capacity not less than 10 KA complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, MCB 'B' series type suitable for 240 volts, AC supply, 5 to 40 Amps, single pole with over load and short circuit protection and rupturing capacity not less than 10 KA complete all as specified and directed by Engineer-in-Charge.

S&F in replacement security light fittings LED type 25 Watt with all necessary accessories, clear transparent acrylic cover, prewire suitable to operated on 230 Volts, 50 Hz, AC and supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 32mm bore "light grade" brackets 2 Mtr length bent to shape to obtain required shape including clamps, nuts, bolts, washers etc. connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer-in-Charge. Make : Havells Cat part No. ENDURAPEARLSL25WLED757SASYTOPCMP, Bajaj Cat Part No. BRLEP 25W LED WH, Crompton Cat Part No. LSTS-25-CDL-M

S&F in replacement of meter box of size 0.9m x 0.9m x 0.2m made out of CRCA mild steel sheet, thickness 2.25mm double door, single opening with lock arrangement and transparent glass for meter reading suitable for fixing 04 electric meter and VTPN DB box including taking down existing electric meters, refixing them with two single core PVC copper conductor unsheathed wire multistranded 4 Sqmm, properly painting on meter box complete and fixing in wall with suitable cutting, cement work etc. complete all as specified and directed by Engineer-in-Charge.

Supplying, laying, jointing and testing and commissioning of 25 sqmm, 4 core XLPE insulated, screened, PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & PVC sheathed LT cable 1100 volts grade conforming to IS-7098 laid in trenches/ ducts/ fixed on poles/wall/laid under roads/paths/drain/culverts or passing through pipes complete all as specified and directed by Engineer-in-Charge. Note :Excavation, earth work, sand cushioning and brick protection required for item shall be measured and paid separately under respective items of BOQ.

M&L for Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth of not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick and packed layer of charcoal dust and common salt, connected to galvanized earth turbo GI wire 4mm dia earth lead by means of bolts, nuts and washers of the earth strip galvanised iron or steel and thimbles and other end of the earth strip connected to earthing test point and protected by galvanised iron pipe light grade 15mm dia and water pipe 20mm dia GI light grade with funnel & wiremesh, PCC chamber in cement concrete (1:2:4) type B-1 and CI cover with frame, excavation & earth work complete all as shown in electrical plate No. 3 of MES Schedule Part-I of SSR-2009. complete all as specified and directed by Engineer-in-Charge. Notes :- (i) GI earth strip upto earth test point/ equipment is included in this item. (ii) Outer edge of earth pit chamber shall be 1 metre away from the outer edge of PCC chamber. (iii) 20mm dia GI pipe for watering to be provided with a socket and plug and should be 30cm above ground level (iv) GI strip upto DBs earth connection is included in the respective item of BOQ (v) GI pipe 40mm dia protection pipe shall be provided upto ground level.

Excavation in trenches, not exc 1.5 m wide and n. exc 1.5 m depth; or n exc 10 Sqm on plan and n exc 1.5 m in depth for foundations of poles, struts, stays etc. or laying underground cable etc. in soft/loose soil, & getting out complete all as specified and directed by Engineer-in-Charge.

Returning, filling in soft/loose soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick in soft/loose soil complete all as specified & directed by Engineer-in-charge.

Removal of excavated surplus soil to a distance n.exc 250m and depositing where directed at level not exceeding 1.5 m above the starting point complete all as specified & directed by Engineer-in-charge .

M & L for sand cushioning with river washed and screened dry fine sand to under ground cable after laying the cable jently punning down complete all as specified and directed by Engineer-in-Charge. NOTE:- Thickness after punning shall be considered for payment.

S&F in replacement, sheet metal enclosure single pole and neutral with two pin and earth plug and socket complete with one single pole MCB 20 Amps, 240 Volts complete all as specified and directed by Engineer-in-Charge.

M & L for brick protection with old size sub class 'B' bricks laid flat , length of bricks across the route of underground cable complete all as specified and directed by Engineer-in-Charge. ---------------------------------------------------------------------------------------------- Note : A sum of Rs. 27,017.00 will be deducted on account of credit for dismantled/ demolished / taken down material. Please refer details on Srl Page No. 34 & 35(R) (Schedule of Credit) of Tender document

PAREEK AND COMPANY

KHANNA CONSTRUCTIONS