Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹23.8 LAccepted-AOC 37 PUNJABI COLONY NEAR RAILWAY CROOSING ARYA SAMAJ ROAD MATHURA U P | MATHURA | MATHURA | UTTAR PRADESH | 281001 | L1 | Accepted-AOC THE LOWEST TENDERER | |
| 2 | L2₹24.8 L+₹1.0 L (4.42%)Rejected-Finance | L2 | Rejected-Finance NOT THE LOWEST TENDERER | |
| 3 | L3₹26.0 L+₹2.2 L (9.34%)Rejected-Finance C 56 6 ANAND VIHAR COMMERCIAL COMPLEX MAHOLI ROAD MATHURA UP PIN 281004 | MATHURA | UTTAR PRADESH | 281004 | L3 | Rejected-Finance NOT THE LOWEST TENDERER | |
| 4 | L4₹27.0 L+₹3.3 L (13.7%)Rejected-Finance | L4 | Rejected-Finance NOT THE LOWEST TENDERER | |
| 5 | L6₹31.4 L+₹7.7 L (32.2%)Rejected-Finance 144 VIKAS BAZAR MATHURA UP 281001 | MATHURA | MATHURA | UTTAR PRADESH | 281001 | L6 | Rejected-Finance NOT THE LOWEST TENDERER |
| Sl No | Description | Qty | Unit | M/s RCC L2 | Ms Kamal Kant Agarwal L3 | M/s R L PAREEK L6 | shyam construction L1 | M/s A.K. ENGINEERS L7 | PRABHAT ENGINEERING SOLUTION AND SERVICES L8 | DEVI DAYAL CONSTRUCTION CO L5 | M/S S S CONSTRUCTION L4 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1.00 | M&L for preparation of old steel surface of LT Panel board/Feeder Pillar box of any size by scrubing the existing damage paint and applying two coats of synthetic enamel paint over a coat of red oxide primer at various location in Mathura Cantt complete all as specified and as directed. | 18 | Each Job | 250 ₹4,500 | 700 ₹12,600 | 350 ₹6,300 | 250 ₹4,500 | 340 ₹6,120 | 99 ₹1,782 Lowest | 350 ₹6,300 | 500 ₹9,000 |
| 2.00 | M&L for welding works to LT Panel/Bus Bar/Feeder pillar box for fixing/welding hinges, locking arrangement or reapir pitted area etc at site complete all as specified and as directed. | 10 | Each | 80 ₹800 | 500 ₹5,000 | 160 ₹1,600 | 100 ₹1,000 | 155 ₹1,550 | 49 ₹490 Lowest | 250 ₹2,500 | 450 ₹4,500 |
| 3.00 | Supply, installing, commissioning and testing of bus bar chamber outdoor type, cubical type made out CRCA sheet of 3.15 mm thick dust and vermin proof and angle iron of suitable size, pedestal flame grouted in PCC 1:2:4 type B-1 (using 20mm graded stone aggregated) thimble and cable entry boxes with cable glands, bus bar should covered from all sides with front and back complete with 200 Amps (phase) & 200 Amp (Neutral) rated aluminium bus bar of suitable size, including painting with two coats synthetic enameled paint over a coat of red oxide primer consisting of the following accessories and make as per make list of tender documents:-
(a) MCCB 200 Amp 4 pole, 415 V 36 KA - 01 Nos (for incoming).
(b) Aluminium bus bar 200 Amp for three phase and 200 Amp neutral.
(c) Digital volt meter with selecter switch - 01 Nos.
(d) Digital voltmeter ameter and RYB indicator - 01 Nos.
Note :- Drawing of LT feeder Pillar shall be got approved from Engineer-in-Charge before placing order for procurement. | 1 | Each Job | 34,000 ₹34,000 | 10,000 ₹10,000 Lowest | 35,000 ₹35,000 | 20,000 ₹20,000 | 36,000 ₹36,000 | 29,900 ₹29,900 | 25,000 ₹25,000 | 27,000 ₹27,000 |
| 4.00 | Excavation in trenches not exceeding 1.5 mtr in depth and not exceeding 1.5 mtr wide for foundations, laying of cables etc. and getting out as in soft/loose soil complete all as specified and as directed. | 785 | Cum | 85 ₹66,725 | 90 ₹70,650 | 120 ₹94,200 | 80 ₹62,800 Lowest | 115 ₹90,275 | 130 ₹1,02,050 | 100 ₹78,500 | 90 ₹70,650 |
| 5.00 | Dismantling old unserviceable cross arms and anti climbing devices of any size from pole/structures complete all as specified and as directed. | 5 | Qtl | 80 ₹400 Lowest | 300 ₹1,500 | 120 ₹600 | 100 ₹500 | 115 ₹575 | 150 ₹750 | 150 ₹750 | 130 ₹650 |
| 6.00 | M&L for mild steel cross arms, bracings, support, clamps and back plates fabricated from structural steel section confirming to Fe-410-O or Fe-310-O including nuts, bolts and washers welding, bending cold or hot drilling holes for bolts in any shape or size all as directed including applying two coats of aluminium paint over a coating of red oxide primer complete all as specified and as directed. | 5 | Qtls | 95 ₹475 Lowest | 7,000 ₹35,000 | 6,800 ₹34,000 | 5,500 ₹27,500 | 6,777 ₹33,885 | 8,000 ₹40,000 | 6,200 ₹31,000 | 10,000 ₹50,000 |
| 7.00 | Cutting wild grass, bushes, creaper, unwanted vegetation from inside / surrounding of E/M installations, near transformers, pole structures etc including cutting creapers from barbed / cattle fencing of the installations as when directed and removing of unwanted material from installation compound and depositing complete all as specified and as directed.
Note : The item shall be operated maximum three times in entire period of contract in the same installations. (Area shall measured separately each time). | 4,800 | Sqm | 8 ₹38,400 | 10 ₹48,000 | 10 ₹48,000 | 4 ₹19,200 Lowest | 9 ₹43,200 | 5 ₹24,000 | 8 ₹38,400 | 6 ₹28,800 |
| 8.00 | Supply, installing, commissioning and testing of LT panel board outdoor type, cubical type made out CRCA sheet 3.15 mm thick, inner sheet 2.0 mm thick, dust and vermin proof as per IS/IEC-:61439-1:2011, 61439-2:2011 having thimble and cable entry boxes with cable glands. Panel should covered from all sides with front and back lockable door and hinges complete with aluminum bus bar 300Amp - 03 Nos for Phase and 01 No for neutral, (in separate chamber) mounted/fixed on suitable size angle iron frame/stand embedded in cement concrete type B-1 1:2:4 (using 20mm graded stone aggrigates) including painting steel surface with two coats of synthetic enameled paint over a coat of red oxide primer and consisting of the following:-
(a) MCCB 200 Amp, 4 Pole, 36KA adjustable thermal and adjustable magnetic (I/C) -01 No
(b) MCCB 63A, 16 KA, 3 Pole fixed thermal and fixed magnetic (O/G)- 04 Nos
(c) Digital meter with Voltmeter (0-500V) - 01 No
(d) Rating of CT & Ammeter as per Bus bar capacity as mentioned in BOQ
(e) Selector Switch for Ammeter (R,Y & B) - 01 Set
(f) Selector Switch for Voltmeter (RY,YB & BR) - 01 Set
(g) Indicationg Lamps (R,Y,B) - 01 Set
Note : Drawing of LT panel shall be got approved from Engineer-in-Charge before placing the order for procurement. | 2 | Each Job | 67,000 ₹1,34,000 | 6,000 ₹12,000 Lowest | 68,000 ₹1,36,000 | 55,000 ₹1,10,000 | 67,900 ₹1,35,800 | 89,000 ₹1,78,000 | 65,200 ₹1,30,400 | 64,000 ₹1,28,000 |
| 9.00 | Supply, installing, commissioning and testing of LT panel board outdoor type, cubical type made out CRCA sheet 3.15 mm thick, inner sheet 2.0 mm thick, dust and vermin proof as per IS/IEC-:61439-1:2011, 61439-2:2011 having thimble and cable entry boxes with cable glands. Panel should covered from all sides with front and back lockable door and hinges complete with aluminum bus bar 200Amp - 03 Nos for Phase and 01 No for neutral, (in separate chamber) mounted/fixed on suitable size angle iron frame/stand embedded in cement concrete type B-1 1:2:4 (using 20mm graded stone aggrigates) including painting steel surface with two coats of synthetic enameled paint over a coat of red oxide primer and consisting of the following:-
(a) MCCB 100 Amp, 4 Pole, 25KA adjustable thermal and adjustable magnetic (I/C)- 01 No
(b) MCCB 63A, 16 KA, 3 Pole fixed thermal and fixed magnetic (O/G)- 02 Nos
(c) Bare MCCB space - 02 No
(d) Digital meter with Voltmeter (0-500V) - 01 No
(e) Rating of CT & Ammeter as per Bus bar capacity as mentioned in BOQ.
(f) Selector Switch for Ammeter (R,Y & B) - 01 Set
(g) Selector Switch for Voltmeter (RY,YB & BR) - 01 Set
(h) Indicationg Lamps (R,Y,B) - 01 Set
Note : Drawing of LT panel shall be got approved from Engineer-in-Charge before placing order for procurement. | 4 | Each Job | 66,000 ₹2,64,000 | 35,000 ₹1,40,000 Lowest | 55,000 ₹2,20,000 | 50,000 ₹2,00,000 | 54,800 ₹2,19,200 | 79,000 ₹3,16,000 | 68,000 ₹2,72,000 | 58,000 ₹2,32,000 |
| 10.00 | M&L for sand cushioning to under ground cable in trenches in layers of 8 cm thick before laying the cable and 15 cm thick after laying of cable and stretching the cable and punned the sand as specified complete all as specified and as directed.
Note : Punned depth shall be measured for payment. | 235 | Cum | 250 ₹58,750 Lowest | 450 ₹1,05,750 | 550 ₹1,29,250 | 350 ₹82,250 | 520 ₹1,22,200 | 300 ₹70,500 | 450 ₹1,05,750 | 375 ₹88,125 |
Tender Value
₹50 L
EMD Value
₹1 L
Closing Date
29 Jul 2025, 6:00 pmClosed
GARRISON ENGINEER EAST MATHURA
GE (East) Mathura
PERIODICAL REPAIR AND MAINTENANCE TO LT UG CABLE NETWORKS AND ALLIED WORKS AT ZONE B AND ZONE D UNDER GE (EAST) MATHURA
2025_MES_719186_1
1495/E8
Open Tender
Electrical and Maintenance Works
Works
180 days
GE EAST MATHURA
Please refer Tender documents.
8 documents required · 8 mandatory
₹500
GE (East) Mathura
₹1 L
Yes
16 Sept 2025
8 Jul 2025
31 Jul 2025
8 Jul 2025
29 Jul 2025
22 Jul 2025
8 Jul 2025 - 22 Jul 2025
Amount
M&L for preparation of old steel surface of LT Panel board/Feeder Pillar box of any size by scrubing the existing damage paint and applying two coats of synthetic enamel paint over a coat of red oxide primer at various location in Mathura Cantt complete all as specified and as directed.
M&L for welding works to LT Panel/Bus Bar/Feeder pillar box for fixing/welding hinges, locking arrangement or reapir pitted area etc at site complete all as specified and as directed.
Excavation in trenches not exceeding 1.5 mtr in depth and not exceeding 1.5 mtr wide for foundations, laying of cables etc. and getting out as in soft/loose soil complete all as specified and as directed.
Dismantling old unserviceable cross arms and anti climbing devices of any size from pole/structures complete all as specified and as directed.
M&L for mild steel cross arms, bracings, support, clamps and back plates fabricated from structural steel section confirming to Fe-410-O or Fe-310-O including nuts, bolts and washers welding, bending cold or hot drilling holes for bolts in any shape or size all as directed including applying two coats of aluminium paint over a coating of red oxide primer complete all as specified and as directed.
Cutting wild grass, bushes, creaper, unwanted vegetation from inside / surrounding of E/M installations, near transformers, pole structures etc including cutting creapers from barbed / cattle fencing of the installations as when directed and removing of unwanted material from installation compound and depositing complete all as specified and as directed. Note : The item shall be operated maximum three times in entire period of contract in the same installations. (Area shall measured separately each time).
M&L for sand cushioning to under ground cable in trenches in layers of 8 cm thick before laying the cable and 15 cm thick after laying of cable and stretching the cable and punned the sand as specified complete all as specified and as directed. Note : Punned depth shall be measured for payment.
Supply and Laying Unreinforced precast concrete cable cover class LV type 1, flat, size 250mmx150mmx40mm complete all as specified and as directed.
Returning filling in earth obtained from excavation including spreading, levelling, watering and well ramming in layers not exceeding 25 cms thick complete all as specified and as directed.
Removing surplus soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.
Supplying, laying or fixing or passing through pipe, testing and commissioning XLPE insulated, armoured heavy duty electric underground cable, aluminium conductor 1100 volt grade of following cross sectional area :- Note : Excavation & earth work shall be measured and paid separately under appropriate item(s) of this BOQ.
16 Sqmm 4 core.
25 Sqmm 3.5 core.
35 Sqmm 3.5 core.
50 Sqmm 3.5 core.
70 Sqmm 3.5 core.
95 Sqmm 3.5 core.
120 Sqmm 3.5 core.
150 Sqmm 3.5 core.
185 Sqmm 3.5 core.
240 Sqmm 3.5 core.
Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material and accessories suitable for 3.5/4 core XLPE armoured aluminium conductor cable of size 10 Sqmm to 35 Sqmm complete all as specified and as directed.
Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material and accessories suitable for 3.5/4 core XLPE armoured aluminium conductor cable of size 50 Sqmm to 95 Sqmm complete all as specified and as directed.
Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material and accessories suitable for 3.5/4 core XLPE armoured aluminium conductor cable of size 120 Sqmm to 185 Sqmm complete all as specified and as directed.
M&L for Earthing complete with galvanised steel earth plate electrode 60cmX60cmX6.0mm thick, buried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of the plate not than 1.5mtr below normal ground level connected to GI strip of size 32x6mm by means of bolts, nuts, check nuts and washers of galvanised iron complete earth pit of PCC M-10(Nominal mix) using 20mm graded stone aggregate, 50mm thick earth pit cover of RCC M-15 (Nominal mix) using 20mm graded stone aggregate with MS TMT reinforcement bar of 8mm dia @ 150mm centre to centre both ways, MS handle 10mm dia made to shape, PGI funnel, wire mesh and 15mm bore GI water pipe medium grade and 40mm bore medium grade GI pipe for protection of earth strip from plate to Panel/Bus bar/Electrical equiptment, common salt, charcoal dust including testing on completion complete all as specified and as directed all as shown in electrical plate No. 3 including testing on completion and making good the disturbed surfaces of wall floors etc without claiming extra cost complete. Note : GI strip beyond 7.5Mtr length from earth electrode shall be measured and paid separately.
M&L for GI strip of size 32x6mm as earth continuity conductor burried in ground or drawn in pipe or fixed to wall on saddle complete all as specified and as directed.
M&L for copper strip of size 32x6mm as earth continuity conductor burried in ground or drawn in pipe or fixed to wall on saddle complete all as specified and as directed. Note : Cost of insulating saddle for fixing of copper strip on wall/roof/floor etc shall be included in quoted rates.
M&L for copper earthing in replacement with copper earth plate electrode 90 cm X 60 cm X 5 mm buried directly in ground (earth pit not less than 3.0 mtr deep beliow ground level) with top edge of the plate not less than 2.25 mtrs below normal ground level,connecting to copper strip 32 X6 mm as earthing strip by means of bolts, nut check nut and washers protected with and including 40 mm dia medium grade GI pipe, necessary excavation and earth work, magnesium sulphate (80 Kg) ), charcoal (4 Qtl) and common salt (4 Qtl) filling, watering arrangement with 20 mm GI pipe medium grade including PCC pit with pre cast RCC (1:2:4) cover, GI funnel with test point, testing (all as shown in electrical plate No 5 and commissioning all as specified and as directed.
M&L for laying GI tubing, light grade, 80 mm bore dia as cable protection fixed on walls/poles/underpass/ceiling and laid in floor complete all as specified and as directed.
M&L for laying GI tubing, light grade, 100 mm bore dia as cable protection fixed on walls/ceiling/laid in floor complete all as specified and as directed.
Supply and fixing in replacement of MCCB 400Amp rating, 4-pole 415V, adjustable thermal adjustable megnetic type breaking capacity 36 KA. complete all as specified and as directed.
Supply and fixing in replacement of MCCB 315 Amp rating, 4-pole 415V, adjustable thermal adjustable megnetic type breaking capacity 36 KA complete all as specified and as directed.
Supply and fixing in replacement of MCCB 250 Amp rating, 4-pole 415V, adjustable thermal adjustable megnetic type breaking capacity 36KA complete all as specified and as directed.
Supply and fixing in replacement of MCCB 200 Amp rating, 4-pole 415V, adjustable thermal adjustable megnetic type breaking capacity 36KA complete all as specified and as directed.
Supply and fixing in replacement of MCCB 160 Amp rating, 4-pole 415V, adjustable thermal adjustable megnetic type breaking capacity 16KA complete all as specified and as directed.
Supply and fixing in replacement of MCCB 100 Amp rating, 4-pole 415V, adjustable thermal adjustable megnetic type adjustable thermal adjustable megnetic type breaking capacity 16KA complete all as specified and as directed.
Supply and fixing in replacement of MCCB 63 Amp rating, 4-pole 415V, adjustable thermal adjustable megnetic type adjustable thermal adjustable megnetic type breaking capacity 16KA complete all as specified and as directed.
Supply and fixing in replacement of MCCB 250Amp rating, 3-pole 415V, adjustable thermal adjustable megnetic type breaking capacity 36KA complete all as specified and as directed.
Supply and fixing in replacement of MCCB 200Amp rating, 3-pole 415V, adjustable thermal adjustable megnetic type breaking capacity 36KA complete all as specified and as directed.
Supply and fixing in replacement of MCCB 160Amp rating, 3-pole 415V, adjustable thermal adjustable megnetic type breaking capacity 36KA complete all as specified and as directed.
Supply and fixing in replacement of MCCB 125Amp rating, 3-pole 415V, adjustable thermal adjustable megnetic type breaking capacity 16KA. complete all as specified and as directed.
Supply and fixing in replacement of MCCB 100Amp rating, 3-pole 415V, adjustable thermal adjustable megnetic type breaking capacity 16KA complete all as specified and as directed.
Supply and Fixing in replacement of spreader terminal for MCCB in LT panel/Feeder pillar box suitable for rating 80 Amp to 100 Amp ,4 pole,50 HZ,AC complete all as specified and as directed.
Supply and Fixing in replacement of spreader terminal for MCCB in LT panel/Feeder pillar box suitable for rating 125 Amp to 200 Amp ,4 pole,50 HZ,AC complete all as specified and as directed.
Supply and Fixing in replacement of spreader terminal for MCCB in LT panel/Feeder pillar box suitable for rating 200 Amp to 400 Amp ,4 pole,50 HZ,AC complete all as specified and as directed.
Supply and Fixing in replacement of spreader terminal for MCCB in LT panel/Feeder pillar box suitable for rating 500 Amp to 630 Amp ,4 pole,50 HZ,AC complete all as specified and as directed.
Dismantling & taking down of old unserviceble Aluminium conductor of any sizes from existing incl aluminium binding wire from over head lines on LT poles complete all as specified and as directed. Note : (i) Weight of old conductors shall be calculated from normal weight given in table of relevant IS code. (ii) weight shall be determined by measuring the horizontal distance between C/C of two adjacent poles.
Dismantling & taking down of GI wire/stay wire of any size complete all as specified and as directed.
Dismantling & taking down old unserviceable pin/loop/shackle type insulator any type and size complete all as specified and as directed.
M&L for ACSR conductor of any size/incl jointing with & including aluminium binding wire 2mm dia & stretching over for over head lines fixed to insulators after allowing specified sag complete all as specified and as directed. Note : (i) Weight of old conductors shall be calculated from normal weight given in table of relevant IS code. (ii) weight shall be determined by measuring the horizontal distance between C/C of two adjacent poles. (iii) The ACSR conductor shall confirming to IS398 Part II & as specified in SSR part-I. (iv) The rate quoted incl for S&F of binding wire, aluminium tapes etc which shall not be included in weight of conductors for payment.
M&L for GI wire 4mm dia as continuous earth wire, guarding and craddles to OH line including binding wire of required size/dia complete all as specified and as directed.
S&F pin type porcelain vitreous white, brown or green insulators 100 mm height and 65 mm dia for 1100 Volts grade including one galvanised mild steel spindle, one nut and two washers complete all as specified and as directed.
S&F shackle type porcelain vitreous white, brown or green insulators of size 75 mm height and 90 mm dia incl galvanised mild steel straps 31x3 mm size ,washers,insulator 12 mm diabolt, washers and nut for working pressure 1100 Volts grade complete all as specified and as directed.
M&L for loop insulator, vitreous, porcelain, white, brown or green, large size with overall dimensions 50x140mm clearance of hole 25.5 mm, working pressure 1100volt complete all as specified and as directed.
M&L for stay assembly complete with MS stay plate 300x300x6mm thick galvanized stay rod not less than 20mm dia, 2.15 M long galvanized stay bow, galvanized thimble,stay clamp etc complete all as shown in electrical plate No1of SSR part-I including excavation, earth work and cement concrete complete all as specified and as directed. Note:- Excavation, earthwork, cement concrete, loop type insulators and stay wire shall be included in the unit rate quoted by contractor.
Dismantling of stay assembly complete from site complete all as specified and as directed by Engr-in-charge.
Excavation in post hole (or similar hole) each n exc 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around,in layers not exceeding 25 cm in soft/loose soil complete all as specified and as directed.
M&L for providing cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.
Supply only chain link fencing any size and type mild steel galvanised complete all as specified and as directed.
Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rail, straining bolts etc including provision of binding wire complete all as specified and as directed. Note :- (i) Supply only fencing will be measured and paid separately. (ii) Supply and fix mild steel nut bolt, line wire and flat will be measured and paid separately.
Supply and fixed mild steel section for post and struts in fencing including cutting top to shape as directed, drilling hole notching for wire etc or flat iron fillet (for security wire mesh etc) including all necessary drilling, bolting or riverting etc confirming to Fe-290 Gde E-165 complete all as specified and as directed.
Supply and fixed mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5 cm long & dia of shank 11 to 15 mm complete all as specified and as directed.
M&L for preparation of new steel surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of zinc chromate primer complete all as specified and as directed.
Supply and fixing in replacement of CT coil suitable for Amp meter 100 /5 Amp complete . Make - AE /ENERCON /EPCOS
Supply and fixing in replacement of indicating lamp set RYB for phase indication operating 240 volt 50 HZ AC with new one LED panel mounting type complete to match existing one all as directed . Make --L&T /C&S /ABB
Supply and laying electrical insulation rubber mating for installations of size 1mx2mx25mm thick as per latest IS complete all as specified and as directed.
Supply and laying electrical insulation rubber mating for installations of size 1mx2mx20mm thick as per latest IS complete all as specified and as directed.
Supply,installing,commissioning and testing in repair of LT panel board outdoor type, size 1510 mmX1360 mm X 450 mm ,cubical type made out CRCA sheet 3.15 mm thick dust and vermin proof and angle iron of suitable size, pedestal flame grouted in PCC (1:2:4) type B-1 20 mm graded stone aggregated thimble and cable entry boxes with cable glands. Panel should covered from all sides with front and back lockable door and hinges complete with 300 Amp(Phase) & 200 Amp(Neutral) rated aluminum bus bar of of suitable size,(in separate chamber) including painting with two coats synthetic enameled paint over a coat of red oxide primer and consisting of the following:- (a) MCCB 250 Amp , 4 pole,25 kA -01 Each (01 I/coming) (b) MCCB 125 Amp, 4 pole,16 kA -02 Each (c) MCCB 100 Amp,4 pole,16 kA,-03 Each (d) Digital Amp meter (0-250)-01 Each (f) RYB Indicator-01 Set
M/s RCC (BID ID -3374511)
Ms Kamal Kant Agarwal (BID ID -3374537)
M/S S S CONSTRUCTION (BID ID -3376280)
DEVI DAYAL CONSTRUCTION CO (BID ID -3376191)
M/s R L PAREEK (BID ID -3375613)
M/s A.K. ENGINEERS (BID ID -3375860)
PRABHAT ENGINEERING SOLUTION AND SERVICES (BID ID -3375173)
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .