PROVN OF JAFFRI WALL AROUND MD ACCN AT KV COMPLEX AND OTHER SANCTIONED WORKS IN THE AREA OF AGE B/R I UNDER GE PANAGARH

Amount

Excavation in trenches not exc 1.5m wide and not exc 1.5m deep for foundation etc or for shafts n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

M&L for broken stones hard core gauge n.exc 63mm deposited, spred and levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregates) as in bed concrete for foundation filling & mass concrete complete all as specified and directed.

M&L for brickwork with fly ash old bricks straight or curved on plan to any radius built in CM (1:6) complete all as specified and directed

Removing surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter for rough finished surfaces of concrete complete all as specified and directed.

M&L for reinforced cement concrete (Design Mix) M-25 (20mm graded stone aggregate) foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc. and mass concrete etc complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete of Gde Fe 410 -W (GdeE- 250) quality- A, complete all as specified and directed.

M&L for two coats of synthetic enamel paint on new surface over one coat of red oxide primer including preparation of surface of any description, over 10 cm in width or girth not other wise described all as specified and directed by Engr-in-Charge.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No 11.00 mentioned above 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

Providing precast cement concrete louvres and jallies, type B0 1:2:4 (12.5mm graded aggregate), 35 mm thick (measured solid), including all mouldings but excluding frame (Pre cast frame shall be measured separately and paid for under item and set in CM 1:4 complete all as specified and directed.

M&L for rendering 15 mm thick cement plaster in CM 1:4 on external fair faces of brick/concrete work surfaces finished even and smooth (without using extra cement) incl WPC (WPC will be measured and paid separately) complete all as specified and directed.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50g and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. (Make: M/s Apex Ultima of Asian/ Weather Coat all guard of Berger/Xtra Tough of Shalimar)

M&L for fixing PVC (SWR) pipes of 75 mm bore diameter single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

M&L for cast- in- situ cement concrete in Type B0 1:2:4 (12.5 mm graded aggregate) in lintels upto 1.5 m clear span, cills,steps and other similar bands, plinth courses,string courses and railings upto 60cm in height ,copings,apex stones,kerbs and the like including weathering ,slightly rounded or chamfered angles and throating as desired complete all as directed by the Engg-in-charge.

M&L for Excavating over areas not exceeding 1.5 m deep and getting out in soft/loose soils complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or in foundation, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for PCC (1:4:8) 100 mm thick Type D2 using 40 mm graded aggregate used as in sub base floor/pavings and finishing complete all as specified and as directed.

M&L for PCC M-25 (Design Mix) (not less than 150 mm thick) Type A1 using 20 mm graded aggregate used as in cement concretei in foundations, filling and mass concrete complete all as specified and as directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

Forming Contraction (Dummy) joints 65 mm deep x 10mm wide filled with sealing compound grade B complete all as specified and directed.

Forming Construction joint 45 mm deep x 10mm wide filled with sealing compound grade B complete all as specified and directed.

M&L for Excavating over areas not exceeding 1.5 m deep and getting out in soft/loose soils complete all as specified and directed.

Removing excavated soil to a distance exc. 250 m but n exc. 500m and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and as directed.

M&L for cement concrete type B-2, 1:2:4 (using 40 mm graded stone aggregate) in surface channels and drains for benching complete all as specified and directed

M&L for extra for forming fair finish drain channel upto 30 cm inner grith in cement concrete using extra cement complete all as specified and directed

M&L for Sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M- 35 Grade with grey cement and pigments complete all as specified and directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc of Fe 410 -W (GdeE- 250) quality A complete all as specified and directed.

S&F wind ties for roof including securing bolts, flat iron fillets(for securing weather boarding with screw bolts and nuts) includingall necessary drilling or riveting etc and similar work conforming to Fe 410-O or Fe-310-O, complete all as specified and directed

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15 cm thickness (below or above ground level) complete all as specified and directed

E/M PORTION Supply & fixing XLPE armoured cable 10 sqmm 2 core,1100 volts grade heavy duty cable,ISI marked passing through pipe, with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed complete all as specified and directed

Supply and fixing steel tubular swaged poles type 410 SP -22 (8.5 Meter long ) complete with CI base plate and final including foundation and coping complete all as specified and directed

Supply and fix sintex box 415 Volt including 4 bus bar of 100 Amp rating cable glands busbar base including of size 250x200x105 etc complete all as specified and directed Cat part No GSJB-2520 Make : Sintex

Supply and fixing security light fittings 35 watts 230v, minimumm lumen output 100 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65/66 including necessary connection complete suitable for service brecate dia 25mm complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size complete all as directed.

Material and labour for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. Note :- If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department.

S&F security street light fittings 60 watts 230V outdoor typewith high pressure dia cast aluminium housing and heat resistnat complete with driver, lamp bracket with impact and corrosion resistant including thermal managaement in multiple optics complete with IP65/66 protection complete all as specified and as directed.

Supply and passing through steel tubler pole/service connection, 1100 volts grade multicore round insulated copper conductor and sheathed flexible cable, multistranded, three core of nominal cross sectional area size1.5 sqmm complete all as specified and as directed.

Supply and laying cable in trenches or passing through pipe, XLPE insulated, heavy duty, galvanised steel strip or wire armoured electric LT cable with stranded aluminium conductor for 1100 volts grade cross sectional area 10 sqmm 4 core complete all as specified and as directed.

M&L for river sand, washed and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling att as specified in SSR Part 2009 complete as specified and directed . Note :- Punned thickness 18 cm shall only be considered for payment

Supplying and laying un-reinforced precast concrete cable cover, Class LV, Type I, flat size 250mm x 150mm x 40m complete all as specified and directed.

S&F and laying 40mm bore, steel tubing, galvanised, light grade with all fitting laid across road, in trenches or across PCC drain or along electric pole of floor/wall etc for protection of cable complete all as specified and directed

Steel tubular swaged pole complete with cast iron base pipe, finial taper plug, bolts, nuts & screws as specified type 410 SP-31 (9.0 metres long) complete all as specified and directed

M&L for Horizontal Boring for Passing Protection Pipe up to 80mm Bore (dia), under Road /Foot Path, n.exc 10.00 mtr in a Single Length, complete all as specified and as directed. (Note : Pipe to be measured separately).

M&L for PCC type C2 1:3:6 (using 40mm graded stone aggregate) as in foundation for pole complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as coping for pole including form work and finishing the surfaces even and smooth etc complete all as specified

S&F single arm bracket made of 40mm dia 1.0mtr long for security light, with mounting MS clamp of flat iron size 25x5mm of suitable length 02 pairs including nut bolts etc of suitable size and painting to MS clamp with two coats of aluminium paints over a coat of red oxide metal primer complete all as spedified and directed by Engr-in-Charge

S&F Cable Junction Box 200X160X98mm in size, made out of thermoplastic sheet having IP 65 protection for outdoor installation fixed with 4 way bakelite cable terminals including 03 Nos polymide gland with check nut (M-32 - 2 nos) fixed on poles with flat iron clamps of size 25x3mm, nuts, bolts, washers etc. including applying Two Coats of Synthetic Enamel Paint over a Coat of Red Oxide Zinc Chrome Primer including taking out of old unserviceable cable junction box complete all as specified and as directed. Make : Cat No. K-8250 of HENSEL or equivalent model in SPELSBERG/RITTAL/CAPE

S&F 40 mm High density polyethylene pipe (HDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc. complete all as specified and directed .

M&L for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, buried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth wire electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 15 mm dia GI 'light grade' pipe from upper end of earth plate up to equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. (Note :- (i) If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department. (ii) Testing to be carried out by the contractor in presence of Engr- in- Charge , entered in the eath testing register, prepared and to be maintained by the contractor & submited to Concerned JE E/M. (iii) T&P and testing instrument(Meger) to be provided by the contractor at own cost)

S.P.S. SUPPLIERS (BID ID -3073308)

S.D.ENTERPRISE (BID ID -3073445)

KAZI SAHABUL ALAM (BID ID -3077324)

M/s S A TRADING (BID ID -3073556)