civil works

Amount

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the University Engineer and clearing and levelling the site, etc., complete as per standard specifications and as directed by the University Engineer.

Plastering with Cement Mortar 1:5 (One cement and five M.sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the University Engineer.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (one cement and three crushed stone sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the University Engineer.

Cement concrete 1:5:10 (one cement, five crushed stone sand and ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification.

Plain Cement Concrete 1:3:6 (one cement, three crushed stone sand and six hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the university Engineer.

Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specifications and as directed by the University Engineer.

Supplying fabricating angles ISA of size 65x65x8mm thickness including welding works and over one coat of red oxide primer etc., complete complying with standard speciifcation and as directed by the University Engineer.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the University Engineer).

Painting old iron works for doors, windows and Ventilators, Iron bars, Weldmesh, wiremesh, screen, steel bars, flats and other similar works etc., with two coat of best and approved quality of synthetic enamel paint over the existing painted surface in all floors. The rate is inclusive of cost of all materials and labour, brushes and scaffolding charges etc., complete complying with standard specification. (The paint to be used should be got approved by the University Engineer) before use on work.

BRICK WORK in cement mortar 1:5 (One cement and five crushed stone sand) using Fly ash bricks of size (230 X 110 X 70 mm) for the following including curing etc., complete complying with standard specifications. (Masonry projections wherever necessary for obtaining required elevation shall be done without extra cost).

a) For foundation and basement

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (one cement and three crushed stone sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the University Engineer.

Pointing the joints of machine pressed tiles with cement mortar 1:3, the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the University Engineer.

Providing and filling the tile joint with epoxy grout with following specification: Surface preparation including cleaning the joint to be free from dust and loose particles. Providing masking tape on either side of the tile joint edges and providing sealing the tile gap with epoxy tile joint grout and finishing neatly and as directed by the University Engineer. The rate inclusive of cost of materials and labour, etc., complete complying with standard specification and as directed by the University Engineer.

Providing expansion joint in RCC floor slab for 12.5mm width using polysulphide as sealent on the top and bottom for a depth of 7.5mm each and packing the inner space using compressible non-absorbent filler materials including cost of labour for cutting and fixing filler materials and laying polysulphide sealent with necessary spatula etc., Excluding cost of water bar. complete complying with standard specifications and as directed by the University Engineer.

Supplying and Laying of Good quality Bitumen Felt in 3mm bead as per IS 1346:1991 over the expansion joint slab and beams. The felt joints laps should be minimum 100mm and finishing without bubble formation. Works including cost of all materials and labours charges. Complete complying with standard specification and as directed by the University Engineer.

Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per ecommendation of the supplier.The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the University Engineer etc. The rate inclusive of cost of materials and labour, etc., complete complying with standard specification and as directed by the University Engineer.

Paving the floor with best quality Vitrified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by University Engineer before use on works)

Supplying and fixing in position of Solid PVC DOOR SHUTTERS using 19 gauge 19mm MS Sq. tubes for styles and outer frames. 15 mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The overall size of styles shall be 50 x 30 mm.The overall size of top rail, lock rail and bottom rail shall be 75 x 30 mm.The overall size of frames shall be 50 x 45 mm, with suitable rabate for housing the shutter. etc., complete as directed by theUniversity Engineer.

a) Door with frame

b) Door without frame

Supplying and fixing in position best quality PVC soil /waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the University Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level.

a) for 75mm dia pipe

b) for 110mm dia pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

a) PVC Elbow with door i) 75mm dia pvc

ii) 110mm dia pvc

a) PVC elbow i) 75mm dia pvc

ii) 110mm dia pvc

SREE SASTIKA BUILDERS AND CONTRACTORS (BID ID -1529033)