WBHOUSING/AE/KSSD-I/e-NIT-21 OF 2025-26

Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish and stacking anywhere within the compound as directed.

Cleaning the concrete surface by removing dirt and debris, marking defective locations and removing loose concrete by careful stripping untill hard surface is exposed, cutting the concrete to regular shape, wire brushing the exposed surface and removing debris from site complete as per direction of the Engineer - in - Charge.

Applying epoxy based reactive joining agent for joining the old concrete with fresh concrete to be applied within manufacturer's specified time as per manufacturers specification. (0.4 Kg / m² of concrete surface).

Cement concrete (1:1.5:3) with graded stone chips 5.6 mm size with hexagonal square mesh wire netting, I.R.C. fabric mesh or X.P. M. fitted and fixed after tying the existing reinforcement on concrete without distributing the same and with proper scarping and cleaning the reinforcement and disturbed concrete with wire brush etc. after applying a coat of cement including the cost of wire netting I.R.C or X. P. M. & cost of all handling and scaffolding complete as per direction of Engineer-in -charge. 25 mm thick concrete

(a) Applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturer's specification [Cement to be supplied by the Department)

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (i) With 1.6 cement mortar (b) 20 mm thick plaster In second floor

(i) With 1.4 cement mortar (b) 10 mm thick plaster In ground floor

(b) Supplying 'Godrej' mortice lock chromium plated with keys 6 levers including fitting & fixing complete.

(A) Wood work in posts, post plates, rafters, battens, truss members, purlins etc. fitted and fixed complete (excluding the cost of bolts, paints, but including the cost of nails, screws etc.) (iii) Sal : Malayasian

Supplying, fitting and fixing boiling water proof ply conforming to IS: 710-1977 bonded with phenol formaldehyde synthetic resin conforming to IS: 848-1974 of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-in-Charge. [excluding the cost of supporting frame work and teak wood batten/Lipping] In Second Floor (vi) 19 mm thick ply

(iv) 12 mm thick ply

Supplying fitting, fixing 12 mm MDF board for making jail by cutting with approved design for placing over the tray at false ceilling including acrylic sheet and finished with approved colour.

Supplying fitting, fixing decorative lamination conforming to IS: 2046 : 1995 as per approved make, brand, finish and thickness with fitting, fixing the same on Particle/MDF / Ply Boards with recommended / approved adhesive with proper clipping the sides for etter attachment as per direction of Engineer-incharge. The rate includes the cost of labour, adhesive and all incidental charges thereof. In Second floor Glossy/Matt/Suede excluding surface texture or metallic lustr. (i) Thickness of laminate 1.5 mm

Supplying and affixing optically clear polyester sun control window film having acrylic pressure sensitive adhesive on one side & an acrylic abrasion resistant coating on the other, with composition of infrared absorbing carbon & free from any optical defect. The film characteristics should conform to ASTM E308, ASTM E903, ASTM E84 and ASHIRAE. The film should be pasted after preparatory works without any cracking, delamination, bubbling, discolouring and variation in total transmission of light across the width at any portion along the length doesn't exceed 2% over the average including scaffolding & relevant others to complete in all respect as per manufacturer's specification & direction of Engineer -in-Charge. (Note: This work should not be executed without specific ermission of Superintending Engineer) (b) Superior Quality : Film Thickness - 2.0 Mil, Glare Reduction > 75%, U factor < 1.03, Emissivity < 0.70

Supplying, fitting and fixing in position SS Handle for shutter { Hettich} make with the direction of E.I.C. 150 mm

22" Drawer channel Godrej make

20" Drawer channel Godrej make

Supplying, fitting and fixing Godrej Multi Lock or equivallent .

Removing old scales, blisters etc. of interior surface of walls,ceiling by scraping etc. and preparing smooth and even surface with rendering or cement mortar (1:2) (as necessary), to make the surface suitable for receiving distemper. (Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge).

(b) Rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand(1.5mm thick)

Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In Ground Floor) (b)Two Coats i) Water based interior grade Acrylic Primer

Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : (Two coats) i) Luxary Quality

(a) Priming one coat on steel or other metal surface with synthetic enamel /oil bound primer of approved quality including smoothening surfaces by sand papering etc

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (a) On steel or other metal surface : With super gloss (hi-gloss) (iv) Two coats (with any shade except white)

Supplying, fitting and fixing of high quality paper based wall paper made of good fibres cellulose and recycle paper having more than one layer with a thickness of 225 micron on clean and dry prepared surface( free from dust grease and other loose foreign mats) with adhesive mainly sodium carboxy methyl cellulose, smoothening with dry and soft cloth taking out bubbles and wrinkles during installation complete as per direction of Engineer-in-Charge. including tools and tackels. ( small cut to remove bubbles if there exist applying little adhesive to smooth it out to the peeling area.)

Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge

Sub Total

Please Enable Macros to View BoQ information