Improvement of FIS Amlehar Bhanjal, Tubewell No. 60 Kaloh, Tubewell No. 95 kaloh, Tubewell at Mawa Kaholan (Shamshan Ghat and Bhatta) and Tubewell at Rampur (Mubarikpur)

Amount

Excavation in foundation trenches upto all depths in all classification of earth work such as pick work, jumper work,Chiselling or wedying out of soft and hard rock as blasting is prohibited, saturated soil including bailing out or pumping of water i/c cutting of bitumenous/concreate surface where ever required in all lifts i/c trimning and dressing of sides, levelling of beds to correct grade i/c shoring, strufing, blanking, timebering and dewatering wherever requiredstacking usable and unusable and unusable material/soil separetely and after laying jointing and testing of pipes (for pipes, pipe dust, chambers, etc.) returning the usable soil in 15cm layers by ramming asn watering and then disposing of all surplus excarted soil/unusable material as directed within all leads and lists and i/c cost as divertion of traffic, nightsigns boads, fixing coutions boards crossing ones trenchs for access to houses fencing etc. completeing in all respect within all leads and lifts as per direction of Engineer in Charge.

Providing and laying cement concrete 1:4:8 (1cement: 4 sand: 8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinths in all leads and lift and to the entire satisfaction of Engineer-in-charge

Providing and laying cement concrete 1:6:12 (1cement: 6 sand) 12 graded stone aggregate 40mm nominal size) and curing complete excluding the cost of form work in foundation and plinths in all leads and lift and to the entire satisfaction of Engineer-in-charge.

2nd. class brick work using common burnt clay building bricks in foundation and plinth in cement mortor 1:4 (1cement :4 sand) in all lead and lifts and as per the direction of the Engineer-in-Charge.

2nd. class brick work using common burnt clay building bricks in foundation and plinth in cement mortor 1:6 (1 cement : 6 sand) in all lead and lifts and as per the directions of the Engineer-in-Charge.

Filling in plinth with sand under floors including watering ramming consolidating and dressing complete under flooring complete in all respect including carriage of materials in all leads and lifts

P/L RCC seismic beam in cement concrete work 1:2:4(1cement:2sand: 4 graded stone aggregate 20mm nominal size & curing complete excluding the cost of form work and reinforcement for reinforced concrete work in Foundations,footings bases of columns and the like and mass concrete complete in all respect including carriage of materials in all leads and lifts

Providing and laying cement concrete work 1:2:4 (1 cement: 2 sand: 4 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of from work and reinforcement for reinforced concrete work in Suspended floor roofs, landing and shelves and their support balconies, beams, girders, bressumers and contilever upto floor two level complete in all respect including carriage of materials in all leads and lifts

2nd class brick work using common burnt clay building bricks in superstructure in cement mortor 1:6 (1 cement :6 sand) in all lead and lifts and as per the direction of the Engineer-in-Charge.

Half brick work using common burnt clay building bricks in superstructure above 1st floor level in cement mortar 1:4( 1Cement, 4 Sand ) of 2nd class bricks complete in all respect with in all leads and lifts.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to giv a fair finish including centring. shuttering. strutting and propping etc with wooden battens and ballies. height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs.and removal of the same for insitu-reinforced concrete and plain concrete work in Flat surfaces such as soffits of suspended floors, roofs, landings and the like floor etc.upto 200mm in thickness including carriage of materials within all leads and lifts complete as per the direction of Engineer-in-charge.

Vertical sufaces such as walls any thickness partitions and the like including attached pillasters buttresses, plinth and string courses and the like :-

Flat surfaces such as soffits of suspended floor, roofs, landings and like floors etc. upto 200 mm in thickness

Sides and soffits of beams,beam haunching, lintels etc. :-

Providing tor steel reinforcement for RCC work including bending, binding and placing in positon complete including carriage of material in all leads & lifts complete as per the direction of Engineer-in-charge.

15mm cement plaster in single coat in fair side of brick/stone masonery for interior plastering upto floor two level including arrises,internal,founded angles,chamfers and/or rounded angles chamfers and/or rounded angles not exceeding in girth & finished even and smooth in cement mortar 1:6(1cement:6sand) complete in all respect including carriage of materials in all leads and lifts

15 mm cement plaster in single coat on Raugh/fair side of brick masonry for interior plastering upto floor two level including arrises, internal rounded angle, chamfers and /or rounded angles not exceeding 80 mm in girth and finished even and smooth with cement mortor 1:3 ( 1 cement :3 sand ) in all leads and lifts as per the direction of the Enginner-in-Charge.

6 mm thick cement plaster in C.M.1:3 to ceiling with in all leads and lifts complete to the entire satisfaction as directed by the Engineer-in-charge.

Pointing on brick work with cement mortar 1:3 ( 1 cement : 3 sand) within all leads and lifts complete to entire satisfaction as directed by the Engineer-in-charge

P/ F pressed steel door frames manufactured from commercial MS sheets of 1.25mm thickness including hinges, jump lock jamp. Bead and if required angle threshold of MS angle 50 x 25 mm or base tie of 1.25mm pressed MS welded or rigidly fixed together by mechanical means, adjustable lugs with split and tails to each jamp i/c steel butt hinges 2.5mm thick with guards, lock strike plate and shock as specified and applying a coat of steel primer after pretreatment or surface as directed by Engineer-in-charge.

Providing and fixing 1mm thick M.S.sheet door with frame of 40mmx40mmx6mm angle iron 3.15mm M.S. gusset plate at the junctions and corners including all necessary fittings, complete including applying a priming coat of red lead paint.using flat 30mm x6mm for diagonal braces and control cross/pieces complete in all respect including carriage of material in all leads & lifts.

Providing plinth protection 50mm thick in cement concrete 1:3:6(1cement:3sand:6 graded borne stone aggregate 20mm nominal size)including finishing the surface of concrete smooth complete in all respect including carriage of material in all leads & lifts.

50 mm thick CC 1:2:4 ( I Cement: 2 sand 4 stone graded aggregates 20mm nominal size) flooring laid in one layer & finished with a floating coat of neat cement complete in all respect including carriage of material in all leads & lifts.

40 mm thick CC 1:2:4 ( I Cement: 2 sand 4 stone graded aggregates 20mm nominal size) flooring laid in one layer & finished with a floating coat of neat cement complete in all respect including carriage of material in all leads & lifts.

Providing 40x3 mm flat iron hold fast 40 cm. Long including fixing to frame with 10 mm diameter bolts nuts and wooden plugs and embeding in cement concrete block 30x10x15cm. 1:3:6 (1 cement : 3 sand : 6 gragded stone aggregate 20mm nominal size) complete in all respect including carriage of material in all leads & lifts.

Providing and fixing M.S. grills of required pettern in windows frames of windows etc. with M. S. Flats Square or round bars with round headed bolts and nuts or by screws. (Plain grill) complete in all respect including carriage of material in all leads & lifts.

Providing and fixing M.S.Handles with necessary screws complete in all respect ( 125 mm ) complete in all respect including carriage of material in all leads & lifts.

Providing and fixing M.S.Tower bolts ( Barrel type ) with necessary screws complete in all respect ( 200X10 ) complete in all respect including carriage of material in all leads & lifts.

Providing and fixing sliding door bolts,black enamelled with nuts and screws complete in all respect ( 250X16 ) complete in all respect including carriage of material in all leads & lifts.

P/F on wall face Cast Iron rain water pipe 100mm dia i/c fitting and joints with spun yarn and cement mortar 1:2(1cement:2sand ) including clamps complete in all respect including carriage of material in all leads & lifts.

Applying a priming coat With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works complete in all respect including carriage of material in all leads & lifts.

Painting two coats With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat) complete in all respect including carriage of material in all leads & lifts.

White washing with lime on undecorated wall surfaces two coats to give & even shade i/c thorougly brooming the surface to remove all dirt, dust mortar & other foreign matter. complete in all respect including carriage of material in all leads & lifts.

Finishing wall with water proofing cement paint of approved brand & manufacture & of required shade on undecorated wall surfaces ( Two coats) to give an even shade after thoroughly brushing the surface to remove all dirt & remains of loose powdered materials complete in all respect including carriage of material in all leads & lifts.

Providing and fixing M.S fan clmp type 1 of 16 mm dia M.S bar bent to shape with hooked ends in R.C.C slab during laying including painting the exposed portion of loop, all as per standard design complete in all respect including carriage of material in all leads & lifts.

Steel work welded in built up sections,trusses & framed work including cutting, hoisting & fixing in position & applying a priming coat of red lead paint In grating, framed, guards, bars, ladders, railing, brackets & similar works within all leads and lifts as per direction of Engineer-in-charge.

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant(HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required including carriage of all material within all leads and lifts. Group "C"

Wiring for power plug with 2x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/ recessed PVC Conduct along with 1 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required including carriage of materials within all leads and lifts.

Wiring for light plug with 2X1.5 Sq. mm PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductof cable in surface/recessed PVC & conduit along with 1 No. 1.5 Sq. mm HRFRLS/PVC insulated single core copper conductor cable for earthing as required including carrige of material with in all leads and lifts.

Wiring for Circuitsub main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/ recessed PVC & Conduit along with 1 No. 1.5 Sq mm HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required including carriage of material upto all leads and lifts 2x6Sqm.

Supplying & fixing metal box of 180mm.x100mm.x60mm. deep sizes (nominal size) on surface or in recess with suitable size for fixing phenolic laminated sheet covered in the front including Providing and fixing 5 pin 5/6 amps socket , outlet and 5/6 amps plano type switch connections painting etc. as required arriage of materials within all leads and lifts.:-

Supplying and fixing bakelite batten/angle holder including connections as required.

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible,cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. as required:-Ceiling Fan 1200 mm sweep, Category-A.

Providing and fixing Ultra slim decorative extruded box fixture with domestic electronic ballast, snap-on installers suitable for 28 watt FTL (T5), complete with all accessories (excluding one No.T-5 Tube), connections, testing and commissioning etc. as required. 1 x28 watt-FTL(T-5) (Category-A)

Supplying and erection of 40/50/63 amps rating, 10 KA breaking capacity, 240 volts, "C" curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required. Double Pole Cat-A

Supplying and fixing of following way single pole and neutral sheet steel MCB distribution board 240 volts on surface/recess completed with tinned, copper bus-bar, wire set, neutral link, earth bar, din-bar, detachable gland plate, banking plate cable, identification levels interconnections,phosphatized and power painted, including earthing etc. as required Double Door 8 way.

Supplying and errection 6 Amps to 32 Amps rating 10 KA Breaking capacity 240 volts C Curves miniature ciruite breaker of following poles in the existing MCB, DB complete with connections testing and commissioning etc. as required Category "A", single pole.

Providing installation testing and commissioning of prewired flourscent tube fitting 1x40 watt box type Cat A i.e Bajaj make complete with balast starter and capacitor but excluding flourscent tube rod suitable to operate on 240 volt single phase AC supply directly on surface with copper wiring as required complete as per direction of the Engineer-in-charge.

Earthing with G.I. earth pipe 4.5 mtrs long, 40mm dia including accessories and providing masonry enclousres with cover plate having locking arrangement and watering pipe etc.( but without cheacoator coke and salt) complete as required including carriage of materials within all leads and lifts.

Extra for using salt and charcoal for pipe earth electrode complete as required, including carriage of materials within all leads and lifts.

Supplying and laying 6 SWG G.I.wire at 0.50 mtr below ground level for earth electrode conductor including soldering etc. as required including carriage of materials within all leads and lifts.

Providing, fixing & testing Street Light Fixture with CFL of 36 watt, copper ballast, G.I. Pipe bracket, complete in all respects.

Providing & Laying, jointing and testing in trenches following dia and grade having suitable pressure Kg.F/ cm2 working pressure polythene pipes high density conforming to IS: 4984-1995 complete but ends preparead for Heat/Electric joints including testing of Joints complete( Earth work in trenches to be measured and paid for separately) within all leads and lifts and as per direction of Engineer-in-charge.

160 mm dia HDPE pipe class PE-80, grade PN 4.00

Providing. and fixing Cast Iron Alfa valves of reputed & approved make like Kirloskar/Leaderetc. on distribution system of confirming to with latest ammendments of appropriate class & following dia metre and capable to with stand the requisite nominal seat pressure 10Kg/ Sqmt including testing and upto entire satisfaction of Engineer -in-Charge

200 mm dia

Providing,Laying, jointing and testing in trenches Galvanized mild steel flanged/butt welded pipes below mentioned dia and grade conforming to IS:1239-2004 (with latest amendments)The MS Flanges are to be provided for 5% of total joints as per table below conforming to IS:6392-1971 (latest upto date amendments) and welding of MS flanges with pipe as per IS: 816-1969 with electrodes as per IS:814-1991 including required number and size of MS nuts and bolts as per IS 1369-1967 and compressed asbestos fibre jointing gaskets sheet not less than 3.00mm in thickness as per IS:27121-1965. The welding of flanges to be done on both faces in three layers in each face to make the joints leak proof including all kind of specials such as bends of all degrees to be made from parent tube, short pieces, tail pieces all made from parent tube and to the entire satisfaction of the Engineer-in-Charge. The pipes end should be bevelled suitable for butt welding. the circumferencial butt welded joints (95% of the total joints) by electrical arc welding to following dia & class pipes, welding of pipes to be done in three layers to make joints leak proof and to achieve the minimum effective throat thickness of welded conforming to IS 816-1969 specifications, by using welding electrode of 2.5mm to 6.3 mm of Advani oerlikon (Adore)-CITOJET/ESAB make conforming to IS 814-1991, at site of work complete in all respect and including DPT test for joints & manual/mechanical handling of pipes.The laying of Pipes conform to IS 5822 (with latest ammendentments upto date) including all kind of specials such as bends of all degrees to made from parent tube, short pieces, tail pieces all made from parent tube within all leads and lifts (Earth work in trenches, MS flanges and butt welded joints to be measured and paid for seperately)

GMS pipe 125 mm dia ( Medium grade) 4.80 mm thick

Providing, welding and fixing of MS flanges @ 5% of total joints conforming to table as specified below of BIS-6392-1971 ( Latest with upto date ammendments) welding of M.S. flanges on ( Two layers on inner face and one layer on outer face of each flange) with GMS pipes and bends on both ends. ( The GMS pipe to be measured and paid for separately. ) The welding of flanges should conforming to IS 816-1998 with electrodes as per IS 814-1997, Prov.& fixed with nuts, bolts of required size conforming to IS 1364, including providing & fixing 3 mm (Minimum) thick compressed asbestos fibre / synthetic rubber gasket conforming relevant BIS Code IS 2712-1965( The earth work in trenches to be measured and paid for seperately) complete in all respect and including entire carriage of materials in all leads and lifts as per the direct1on of the Engineer-in-Charge

MS Flanges 125 mm dia Table- 5

Providing circumferential butt welded joints @ 95% by electrical are welding to GMS ERW pipe welded in requsite number of weld runs so as to achiev the minimum effective throat thickness of weld conforming to IS 816-1969 specifications, by using welding electrodes of 2.5 mm to 6.3 mm of Advani Oeriliken ( adore)-CITOJET/ES/ESAB make conforming to IS 814-1991 include Die peritration test at site of work complete in all respects, including manual/ mechanical handling of pipe in all leads asnd lifts to the entire satisfaction of Engineer-in- charge.125mm dia.

GMS pipe 125 mm dia 4.80 mm thick

Tubewell at 60 Kaloh:- Supply and errection of submersible pumping set of reputed make such as KSB/ Calama / BS/ Worthigton / Groundfos/ LUBI /Hindustan/ Sabar/Seerex/Johnston / Amrut, conforming to latest relevent BIS . The pump should be fitted with free fine impellers of suitable alloys as per BIS ;5659-1978 with upto date amendments, suitable for raw /clear water having greased packed bearing and shell with wound stator on motor side and with shaft protection on pump side ensuring better life for shaft conforming to BIS specifications The pump shall be directly coupled to submersible squirrel cage electric induction motor of same make conforming to BIS ;9283-1979 with upto date amendments, totally dust and water proof for submersible pump, duly isolated from the pump by intermediate casing with double mechanical seal in oil chamber and grease packed,lubricated bearing and provided with stainless steel thrust bearing plate to withstand non vertical loads with minimum wear and tear.It should also be fitted with a device to make up expa-of water with heating of motor The pumpset should include water level guard i/c cable ,errection clamps, cable clips and suitable for opertion on data given below. Specifications offered a Pumps :- Specifications i) Make ii) Model iii) No. of stages iv) Manufacter's certificate to be attached Performance i) Discharge ii) Head iii) Efficiency of Pump a) Duty Head b) (+) 10% Duty Head. c) (-) 15% Duty Head d) Performance curve to be attached b) Motors; Specification i) Make ii) Model iii) B.H.P iv) Speed v) Insulation.

Discharge, (Q) 12.54LPS

Total Head ( H ) 184.41 Mts.

SWL in Tubewell 45 mtr. bgl.

R.L. point of discharge 477.55mtr

R.L. of Pump House = mtr. 456.98 mtr

Seasonal fluctuation + draught condition + bowl assembly.9.00 mtrs.

Drawdown in Tubewell 80.00 mtrs.

StaticHead = 154.57 mtrs.

Static suction lift 144.00 mtrs.

Rising main Column pipe

Length 1080 mtrs Length 144.00 mtr

Dia 125 mm (M) Dia 100 mm (M)

Class GMS (M)

iv) Pumping hours 5413.81 hours

v) Alititude of installations above M.S.L 100mtr

vi) Characteristic of water

(vii) Temperature : 20.00 Deg. C

(viii) Ambient temperature 42.00 Deg. C

(ix) Turbidity < than 50.00 NTU

(x) Alkalinity Mg/Ca Co3

(xi) Size of the solids mm

xii) others

xiii) Depth of T/well 142 mtr

ix) Dia of T/well assembly 200 mm

Length of assembly pipe

Dia of housing pipe

Length of housing pipe

OPERATING CONDITIONS

i) Type of current A.C Three phases.

ii) Frequency 50 Cycles/ Sec.

iii) Rated Voltage 415+/-10% Volts

iv) System of earthing Double Loop earthing as per BIS 3843-1987 latest

v) Speed of Revolution __________________ RPM 2900

MOTOR

i) Ref to BIS code BIS 9283-1979 with upto date amendments

ii) Type of enclousre of motr As per BIS :4691-1985 (latest)

iii) Mechnical out put in HP

iv) Class of insulation : Class B The motor should be able to withstand intial current of 2.50 times the rated current for two minutes without suffering damages of permanet deformations

i) Ref to BIS code BIS 5659-1978 with upto date amendments

ii) Driver Type Electric drivern

iii) Operating Range -25%to +10% of Total head at duty point

iv) Deliver size of Pump ;---------- (to be quoted by tenderer)

Providing ICTP Main Switch with HRC fuses of L&T/ Havells make and having capacity 30% extra of the operational rating as per IS : 13947- P I & II with upto date amendments. i) Make : ii) Type : iii) Capacity : 200 amp.

Providing MS Sheet steel fabricated floor mounted closed ( Almirah type) switch board including angle iron post of suitable height and size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising and capable of mounting the following accessories with all internal connections. Panel/ Switch Board i) Drawing. ii) Layout Plan

MCB of kilburn / L&T/ Havells make of suitable capacity on incoming feeder with or without initial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. i) Make : ii) Type : iii) Range 200 amp. iv) Capacity

ELR of recommended make L&T /Havells as per IS ; 2516-1985 with up to date ammendments and of suitable range which should have control box , operating handle & trip / reset bush button on / off of indicators, reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. ELR i) Make : ii) Type : iii) Range 200 Amp. iv) Capacity

The voltage monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage, reverse phasing, overloading and phase voltage difference as per IS; 3842 ( Latest Edition )i) Make : ii) Type : iii) Range 0-500 amp.

Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS ; 8084-1976 and IS : 11353-1985 read with BIS ; 5578 -1985 with upto date amendments including.Three phase indicator lamps complete with toggle switches for individual motors as per IS 3452 (P- I&II ) with upto date amendments. 3 Phase indicators 3 phase indicators i) Make : ii) Type : iii) Rating

Capacitor of BHEL / L&T make as per IS ; 2834-1968 with upto date amendments, to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter/ IEC make) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments .Rate of capacitor will be approved by HPSEB. i) Make : ii) Type : iii) Range. 13 KVAR

Providing suitable starter of L&T/Havell's /MEI/BHEL/Kilburn make as per IS: 13947-II with up to date amendments for Squirrel Cage motor mounted on panel board with magnetic type overload release and dashpot time lag, under voltage release with or without initial oil filling as the case may be with single phase preventor as per IS 1248 (P-V)-1983 with up to date amendments. Single Phase Preventor i) Make : ii) Type : iii) Range.

Single Phase Preventor i) Make : ii) Type : iii) Range.

Providing and fixing double flanged Cast steel Sluice valve of Leader / Kartar/ Kirloskar /LP/RG Brand make for the delivery line of pump and capable of withstanding the normal seat pressure and as per IS :- 1414-API-600 with latest ammendments i) Make : ii) Type : iii) Make :- Cast steel Class ASA-150 for Column Pipe 100 mm dia

Providing and fixing double flanged swing type cast Steel Reflux valve of Leader/ Kirloskar/Kartar / LP/RG Brand make having Bye pass arrangement on the delivery line of the Pump and capable of 'withstanding normal Seat Pressure as per IS:1868/API-600 with latest ammendments i) Make : ii) Material : Cast steel iii) Class ASA-150 For for R/main 125 mm dia.

Providing and fixing pressure gauge of Prega / Precision make complete with all accessories such as stop cock, copper tubing as per IS ; 3624-1987 with upto date amendements. i) Make :

Supply of PVC Jointless , Flat water proof cables as per BIS 694-1998 Latest with upto date amendments , Suaitable for the pump set offered from MCB to Motor Including all other electrical equipments / accessories such as thimble , flexible pipe solder , nuts and bolts , cable glands etc . laid in pipes or trenches under floor .The tpye size and make shall be subject to approved of HPSEB authorities . i) Make : Finolex/ Havells ii) Size Motor Side:-25 mm2 copper iii). type- IV capacity V Core-3x10mm2 ).

Providing and Lowering of GMS Column pipe for assembly 100 mm dia including MS flanges' of Table 17 as per IS : 6392-1971 with upto date amendments, rubber/asbestos gasket of min. 3mm thickness as per IS 2712-1979 and required numbers of nuts and bolts as per IS ;1364-1983 . The Column pipe shall be as per relevent IS Code and to withstand 1.50 times total head stipulated under item No. 70 . The Column pipe should be extended upto 5 mtr. beyond the outer wall of the pump house in the direction of Rising main . The Column pipe should be properly jointed with the Rising main including all necessary accessories like increaser / reducer, flanges, bends etc, including supporting clamps (2Nos.) at the top of T/well assembly, and as per the direction of Engineer - in - Charge. Column Pipe 100 mm dia GMS pipe (M)

Installation of all items appearing as above as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and laying copper PVC insulated armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS ;1554 (P-I ) 1988 or latest with upto date amendments of Seimen /Gloster / IEC / ICC / EICO / National / Grandlay /Finolex/ Havells make including all other accessories such as thimble, flexible pipes, solder nuts and bolts, cable glands etc. laid in pipes of trenches under floor. Armoured Power Cable A) Supply Side From meter of HPSEB to Bus Bar and Switch)Armoured Power Cable (A) Supply side (From Switch to Starter & Supply Side :-50mm2) ii) Make iii)Type iv) Capacity v) Core 3

(B) Supply Side (From meter of HPSEB to Bus Bar & Switch) i) Size 50 mm2 ii) Make iii) Type iv) Capacity v) Core 3

Providing and fixing double loop earthing with Cooper Plate and Suitable thick electrode complete with material such as thimble, nuts and bolts, charcoal, salt, 25 mm x5 mm as per IS ; 3043-1987 with upto date amendments for motors and other electrical equipments and digging of pits etc. complete in all respect as per the dirction of the Engineer - in - Charge. i) Copper Wire 25x3mm Flat beyond 50HP to 75 HP

Tubewell at 95 Kaloh :- Supply and errection of submersible pumping set of reputed make such as KSB/ Calama / BS/ Worthigton / Groundfos/ LUBI /Hindustan/ Sabar/Seerex/Johnston / Amrut, conforming to latest relevent BIS . The pump should be fitted with free fine impellers of suitable alloys as per BIS ;5659-1978 with upto date amendments, suitable for raw /clear water having greased packed bearing and shell with wound stator on motor side and with shaft protection on pump side ensuring better life for shaft conforming to BIS specifications The pump shall be directly coupled to submersible squirrel cage electric induction motor of same make conforming to BIS ;9283-1979 with upto date amendments, totally dust and water proof for submersible pump, duly isolated from the pump by intermediate casing with double mechanical seal in oil chamber and grease packed,lubricated bearing and provided with stainless steel thrust bearing plate to withstand non vertical loads with minimum wear and tear.It should also be fitted with a device to make up expa-of water with heating of motor The pumpset should include water level guard i/c cable ,errection clamps, cable clips and suitable for opertion on data given below. Specifications offered a Pumps :- Specifications i) Make ii) Model iii) No. of stages iv) Manufacter's certificate to be attached Performance i) Discharge ii) Head iii) Efficiency of Pump a) Duty Head b) (+) 10% Duty Head. c) (-) 15% Duty Head d) Performance curve to be attached b) Motors; Specification i) Make ii) Model iii) B.H.P iv) Speed v) Insulation.

Discharge, (Q) 10.20 LPS

Total Head ( H ) 70.81 Mts.

SWL in Tubewell 18 mtr. bgl.

R.L. point of discharge 491.32 mtr

R.L. of Pump House = 472.02 mtr.

Seasonal fluctuation + draught condition + bowl assembly.9.00 mtrs.

Drawdown in Tubewell 15 mtrs.

StaticHead = 18.00 mtrs.

Static suction lift 52.00 mtrs.

Rising main Column pipe

Length 340 mtrs Length 52 mtr

Dia 125 mm (M) Dia 100 mm (M)

Class GMS (M)

iv) Pumping hours 5069.59 hours

v) Alititude of installations above M.S.L 100mtr

vi) Characteristic of water

(vii) Temperature : 20.00 Deg. C

(viii) Ambient temperature 42.00 Deg. C

(ix) Turbidity < than 50.00 NTU

(x) Alkalinity Mg/Ca Co3

(xi) Size of the solids mm

xii) others

xiii) Depth of T/well 142 mtr

ix) Dia of T/well assembly 300/200 mm

Length of assembly pipe

Dia of housing pipe 300mm

Length of housing pipe

OPERATING CONDITIONS

i) Type of current A.C Three phases.

ii) Frequency 50 Cycles/ Sec.

iii) Rated Voltage 415+/-10% Volts

iv) System of earthing Double Loop earthing as per BIS 3843-1987 latest

v) Speed of Revolution __________________ RPM 2900

MOTOR

i) Ref to BIS code BIS 9283-1979 with upto date amendments

ii) Type of enclousre of motr As per BIS :4691-1985 (latest)

iii) Mechnical out put in HP

iv) Class of insulation : Class B The motor should be able to withstand intial current of 2.50 times the rated current for two minutes without suffering damages of permanet deformations

i) Ref to BIS code BIS 5659-1978 with upto date amendments

ii) Driver Type Electric drivern

iii) Operating Range -25%to +10% of Total head at duty point

iv) Deliver size of Pump ;---------- (to be quoted by tenderer)

Providing ICTP Main Switch with HRC fuses of L&T/ Havells make and having capacity 30% extra of the operational rating as per IS : 13947- P I & II with upto date amendments. i) Make : ii) Type : iii) Capacity : 63 amp.

Providing MS Sheet steel fabricated floor mounted closed ( Almirah type) switch board including angle iron post of suitable height and size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising and capable of mounting the following accessories with all internal connections. Panel/ Switch Board i) Drawing. ii) Layout Plan

MCB of kilburn / L&T/ Havells make of suitable capacity on incoming feeder with or without initial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. i) Make : ii) Type : iii) Range 63 amp. iv) Capacity

ELCB of recommended make L&T /Havells as per IS ; 2516-1985 with up to date ammendments and of suitable range which should have control box , operating handle & trip / reset bush button on / off of indicators, reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. ELR i) Make : ii) Type : iii) Range 63 Amp. iv) Capacity

The voltage monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage, reverse phasing, overloading and phase voltage difference as per IS; 3842 ( Latest Edition )i) Make : ii) Type : iii) Range 0-500 amp.

Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS ; 8084-1976 and IS : 11353-1985 read with BIS ; 5578 -1985 with upto date amendments including.Three phase indicator lamps complete with toggle switches for individual motors as per IS 3452 (P- I&II ) with upto date amendments. 3 Phase indicators 3 phase indicators i) Make : ii) Type : iii) Rating

Capacitor of BHEL / L&T make as per IS ; 2834-1968 with upto date amendments, to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter/ IEC make) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments .Rate of capacitor will be approved by HPSEB. i) Make : ii) Type : iii) Range. 5 KVAR

Providing suitable starter of L&T/Havell's /MEI/BHEL/Kilburn make as per IS: 13947-II with up to date amendments for Squirrel Cage motor mounted on panel board with magnetic type overload release and dashpot time lag, under voltage release with or without initial oil filling as the case may be with single phase preventor as per IS 1248 (P-V)-1983 with up to date amendments. Single Phase Preventor i) Make : ii) Type : iii) Range.

Single Phase Preventor i) Make : ii) Type : iii) Range.

Providing and fixing double flanged Cast iron Sluice valve of Leader / Kartar/ Kirloskar /LP/RG Brand make for the delivery line of pump and capable of withstanding the normal seat pressure and as per IS :- 780-1992 with latest ammendments i) Make : ii) Type : iii) Make :- Cast Iron Class PN-1.00 for Column Pipe 100 mm dia

Providing and fixing double flanged swing type cast Iron Reflux valve of Leader/ Kirloskar/Kartar / LP/RG Brand make having Bye pass arrangement on the delivery line of the Pump and capable of 'withstanding normal Seat Pressure as per IS:5312 Part-1 with latest ammendments i) Make : ii) Material : Cast Iron iii) Class PN-1.6 For for R/main 125 mm dia.

Providing and fixing pressure gauge of Prega / Precision make complete with all accessories such as stop cock, copper tubing as per IS ; 3624-1987 with upto date amendements. i) Make :

Supply of PVC Jointless , Flat water proof cables as per BIS 694-1998 Latest with upto date amendments , Suaitable for the pump set offered from MCB to Motor Including all other electrical equipments / accessories such as thimble , flexible pipe solder , nuts and bolts , cable glands etc . laid in pipes or trenches under floor .The tpye size and make shall be subject to approved of HPSEB authorities . i) Make : Finolex/ Havells ii) Size Motor Side:- 4mm2 mm2 copper iii). type- IV capacity V Core-3 ).

Providing & Lowering of GMS Column pipefor assembly 100 mm dia including MS flanges' of Table 17 as per IS : 6392-1971 with upto date amendments, rubber/asbestos gasket of min. 3mm thickness as per IS 2712-1979 and required numbers of nuts and bolts as per IS ;1364-1983 . The Column pipe shall be as per relevent IS Code and to withstand 1.50 times total head stipulated under item No. 70 . The Column pipe should be extended upto 5 mtr. beyond the outer wall of the pump house in the direction of Rising main . The Column pipe should be properly jointed with the Rising main including all necessary accessories like increaser / reducer, flanges, bends etc, including supporting clamps (2Nos.) at the top of T/well assembly, and as per the direction of Engineer - in - Charge. Column Pipe 100 mm dia GMS pipe (M)

Installation of all items appearing as above as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and laying copper PVC insulated armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS ;1554 (P-I ) 1988 or latest with upto date amendments of Seimen /Gloster / IEC / ICC / EICO / National / Grandlay /Finolex/ Havells make including all other accessories such as thimble, flexible pipes, solder nuts and bolts, cable glands etc. laid in pipes of trenches under floor. Armoured Power Cable A) Supply Side From meter of HPSEB to Bus Bar and Switch)Armoured Power Cable (A) Motor side (From Switch to Starter & Starter to motor) i) Make iii)Type iv) Capacity v) Core 3

(B) Supply Side (From meter of HPSEB to Bus Bar & Switch) i) Size 10mm2 ii) Make iii) Type iv) Capacity v) Core 3

Providing and fixing double loop earthing with G.I/Cooper Plate and Suitable thick electrode complete with material such as thimble, nuts and bolts, charcoal, salt, 25 mm x5 mm as per IS ; 3043-1987 with upto date amendments for motors and other electrical equipments and digging of pits etc. complete in all respect as per the dirction of the Engineer - in - Charge. i) G.I. Wire 4SWG beyond 20HP to 30 HP

Pawan Kumar Sharma (BID ID -605562)

aman sood (BID ID -605471)