PROVN OF CERTAIN LBW WORKS UNDER GE (NORTH) AT BATHINDA MIL STN

Amount

Surface dressing n.exc 15cm deep and getting out Soft/loose soil complete as specified and directed by Engineer-in charge.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out and getting out in soft / loose soil complete all as specified & directed.

Excavation in trenches not exceeding 1.50 meter wide and not exceeding 1.50 meter depth for foundation etc or for shafts , wells, cesspits, manholes , septic tank, for laying of cables , laying of pipes not exceeding 10 Sqm on plan and not exceeding 1.50 meter depth and getting out in soft/loose soil etc complete all as specified and as directed by Engineer-in- charge.

Excavation over areas , not exceeding 1.50 mtr deep and getting out in soft/loose soil complete all as specified and directed by Engineer-in charge.

Exacavation of areas, exceeding 1.50 mtr and not exceeding 3.00 mtr deep and getting out in soft/loose soil complete all as specified and directed by Engineer-in charge.

Exacavation of areas, exceeding 3.00 mtr and not exceeding 4.50 mtr deep and getting out in soft/loose soil complete all as specified and directed by Engineer-in charge.

Removing excavated material as in all kind of Soils not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed by Engineer-in- charge.

Returning filling in any type of soil, including spreading, levelling,watering and well ramming in layer not exceeding 25 cm in each layer, complete all as specified and as directed by Engineer-in- charge.

Material and labour for Plain Cement Concrete 1:4:8 , Type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed by Engineer-in-charge.

Material and labour for Plain Cement Concrete 1:2:4 , Type B-1 using 20 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed by Engineer-in-charge.

Material and labour for RCC M-25 (Design mix) using 20 mm graded stone aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed by Engineer-in-charge. NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Material and labour for RCC M-25 (Design mix) using 20 mm graded stone aggregates as in columns, pillars, piers, posts and struts complete all as specified and as directed by Engineer-in-charge. NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Material and labour for RCC M-25 (Design mix) using 20 mm graded stone aggregates as in beams, cantilevers, bressummers, lintels over 1.5 m span and the like etc complete all as specified and as directed by Engineer-in-charge. NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Material and labour for RCC M-25 (Design mix) using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and as directed by Engineer-in-charge. NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Material and labour for RCC M-25 (Design mix) using 20mm graded stone aggregate as in Chajjas complete all as specified and as directed by Engineer-in-charge. NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Material and labour for RCC M-25 (Design mix) using 20mm graded stone aggregate as in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and as directed by Engineer-in-charge. NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Material and Labour for Formwork to faces of walls,retaining walls, abutments,parapets and staircase railings and similar work including attached pillasters, buttresses,etc.; vertical or to batter on rough finished flat surfaces of concrete complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Formwork of sides of concrete foundations, Footings, Bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter on rough finished flat surfaces of concrete complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Formwork in square,reactangular or polygonal on rough finished surface of concrete to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed by Engineer-in-charge.

Material and labour for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. on rough finished flat surfaces of concrete complete all as specified and as directed by Engineer-in-charge.

Material and labour for Formwork to soffits of suspended slabs such as roof slab, floor slabs, landings and similar work not exceeding 200 mm thick (horizontal or sloping) on rough finished flat surfaces of concrete complete all as specified and as directed by Engineer-in-charge.

Material and labour for Formwork to chullah hoods, chajjas, troughs and similar items including edge on rough finished flat surfaces of concrete complete all as specified and as directed by Engineer-in-charge.

Material and labour for Formwork to edges of concrete flats, treads, breaks in floors,window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in walls, horizon tal or sloping and similarwork exc 10cm but n exc 20cm wide on rough finished surfaces of concrete complete all as specified and as directed by Engineer-in-charge.

Material and labour for mild steel TMT bars 10mm dia and over cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia including making of rungs, handles etc complete all as specified and as directed by Engineer-in-charge. (NOTE : Weight of binding wire shall not be considered for measurement and payment purpose.)

Material and labour for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips directed by Engineer-in-charge.(NOTE : Weight of binding wire shall not be considered for measurement and payment purpose.)

Material and Labour Brick work with sub class ‘B’ burnt clay old size bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed by Engineer-in- charge.

Material and labour for Brick work with fly ash old size bricks straight or curved on plan exceeding 6.0m mean radius built in cement mortar 1:6 complete all as specified and as directed by Engineer-in-charge.

Material and Labour Brick work with sub class ‘B’ burnt clay old size bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and as directed by Engineer-in- charge.

Material and labour Brick work with sub class 'B' old size burnt clay bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Sand filling under floor , under interlocking tiles or in foundation including spreading levelling, watering and well ramming in layers not exc 25 cm etc complete all as specified and as directed by Engineer-in- charge. Note: Sand shall be approved by GE.

Material and Labour for Hard core using broken stone aggregate / Boulders of gauge not exc. 63mm, deposited spread and leveled in layers not exc. 150 mm thick, watered and rammed to a true surface complete all as specified and as directed by Engineer-in- charge.

Material and labour for 100 mm thick cement concrete 1:4:8 , type D-2 using 40 mm graded stone aggregate as in sub base of floor. finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

Material and labour for 150 mm thick cement concrete 1:4:8 , type D-2 using 40 mm graded stone aggregate as along inclined complete all as specified and as directed by Engineer-in-charge.

Material and Labour for 75 mm thick PCC 1:3:6 , Type C-1 using 20 mm graded stone aggregate as in plinth protection, finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in- charge.

Material and Labour for 100mm thick Plain Cement concrete type B-1, 1:2:4 (20mm graded aggregate) for floors and ramp top surface complete all as specified and as directed by Engineer-in-charge.

Material and Labour for rendering 10 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces of walls and finishing the surface even & fair faces without using extra cement complete all as specified and as directed by Engineer-in- charge.

Material and labour for 15mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

Material and labour for 15mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

Supply only Liquid water proofing compound complete all as specified & as directed by Engineer-in-Charge.

Material and labour for rendering 5 mm thick in cement mortar in 1:3 on ceiling/ Chajja and finishing the surface even & smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

Material and Labour for applying cement base wall care putty on external surfaces of walls, external surfaces of soffits of chajjas/ Balcony/ verandha (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and leveling of surfaces in two or more layers) by using ready made cement base wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc complete all as specified and directed by Engineer-in- Charge. Make of cement base wall care Putty : AS described in LIST OF MAKES/MANUFACTURERS under Appendix 'B' here-in-after. Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further finishes. Please note that the further finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order. (ii)The make of cement base wall care putty shall be as per the recommendation of manufacturer of paint.

Material and Labour for applying acrylic wall care putty on internal surfaces of walls and internal surfaces of ceilings/soffits (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and leveling of surfaces in two or more layers) by using ready made acrylic wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc complete all as specified and directed by Engineer-in- Charge. Make of acrylic wall care Putty : AS described in LIST OF MAKES/MANUFACTURERS under Appendix 'B' here-in-after. Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further finishes. Please note that the further finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order. (ii)The make of acrylic wall care putty shall be as per the recommendation of manufacturer of paint.

Material and Labour for Preparation of surfaces and applying 02 coats of Interior Acrylic Emulsion Paint (light shade as approved by GE ) @ 10.00 Sq.m/ litre / 2.00 coats by using roller/brush to wall surfaces over with and including one coat of Interior Acrylic Emulsion Primer @ 10.00 Sq.m / litre / 1.00 coat as recommended for under coat by manufacturer of Interior Acrylic Emulsion by using the brands of Interior Acrylic Emulsion Paint and Interior Acrylic Emulsion Primer as descriped in LIST OF MAKES/MANUFACTURERS under Appendix 'B' here-in-after complete all as specified and directed by Engineer-in- Charge.

Material and Labour for Preparation of surfaces and applying 02 coats of Exterior Acrylic Emulsion Paint ( shade as approved by GE) with highlighter of any approved shade, @ 5.00 Sq.m / litre / 2.00 coats by using roller to External walls / RCC surfaces / Soffits of Chajjas / Roof projections / Cantilevers / Balcony etc. surfaces over with and including one coat of Exterior Acrylic Emulsion Primer @ 11.00 Sq.m / litre / 1.00 coat as recommended for under coat by manufacturer of Exterior Acrylic Emulsion by using the brands of Exterior Acrylic Emulsion Paint and Exterior Acrylic Emulsion Primer as descriped in LIST OF MAKES/MANUFACTURERS under Appendix 'B' here-in-after complete all as specified and directed by Engineer-in- Charge.

Material and Labour for preparing new plastered surfaces of ceilings and applying three coats of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. This shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. About 1.3 Kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub-resistant. Small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the last two coats of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and directed by Engineer-in- Charge.

Material and Labour for Preparation of new surfaces of walls and applying 02 coats of cement base paint (colour of shade as approved by GE) @ 5.00 sq.m/Kg/2 coats over & including one coat of exterior wall cement primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of cement base paint by using the brands of cement base paint and exterior wall cement primer by using brush or roller makes as descriped in LIST OF MAKES/MANUFACTURERS under Appendix 'B' here-in-after complete all as specified and directed by Engineer-in- Charge.

Supply & Fixing Factory made single extruded WPC ( Wood Polymer Composite ) Solid Door Frame / Chowkhat of Size 65mm x 125mm comprising of virgin polymer of K value 58-60 (suspension grade ), Calcium Carbonate and nautral fibers ( Wood Powder / Rice husk / Wheat husk ) and non toxic additives (maximum toxcity index of 12 for 100 gms ) fabricated with miter joints after applying PVC Solvant cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg /cum and screw withdrawl strength of 2200 N (face ) & 1100 N (Edge) minimum Compressive strength of 58 N /sqmm modulus of elasticity 900 N/Sqmm and resisitence to spread of flame of class A category with property of being termite / borer proof , water moisture proof and fire retaident and fixed in position with and including MS hold Fast lugs / SS Dash Fastner of required dia and length with and including Supply and Fixing (03 Nos Per Frame ) 100 mm long SS Butt Hinges complete all as specified and as directed by Engineer-in- charge.

Supply & Fixing Factory made single extruded WPC ( Wood Polymer Composite ) Solid Door Frame / Chowkhat with double rebate of Size 65mm x 100 mm comprising of virgin polymer of K value 58-60 (suspension grade ), Calcium Carbonate and nautral fibers ( Wood Powder / Rice husk / Wheat husk ) and non toxic additives (maximum toxcity index of 12 for 100 gms ) fabricated with miter joints after applying PVC Solvant cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg /cum and screw withdrawl strength of 2200 N (face ) & 1100 N (Edge) minimum Compressive strength of 58 N /sqmm modulus of elasticity 900 N/Sqmm and resisitence to spread of flame of class A category with property of being termite / borer proof , water moisture proof and fire retaident and fixed in position with and including MS hold Fast lugs / SS Dash Fastner of required dia and length with and including Supply and Fixing (03 Nos Per Frame ) 100 mm long SS Butt Hinges complete all as specified and as directed by Engineer-in- charge.

Supply & Fixing Factory made single extruded WPC ( Wood Polymer Composite ) Solid Plain flush door shutter of 30 mm thick, size comprising of virgin polymer of K value 58-60 (suspension grade ), Calcium Carbonate and nautral fibers ( Wood Powder / Rice husk / Wheat husk ) and non toxic additives (maximum toxcity index of 12 for 100 gms ) having minimum density of 650 kg /cum and screw withdrawl strength of 1800 N (face ) & 900 N (Edge) minimum Compressive strength of 50 N /sqmm modulus of elasticity 850N/Sqmm and resisitence to spread of flame of class A category with property of being termite / borer proof , water moisture proof and fire retardant and with and including Supply & Fixing of 02 Nos (per Leaf) SS 150mm long Tower Bolt, Supply & Fixing of 02 Nos (per door) SS 300mm long Sliding Bolt with and including Supply & Fixing of 02 Nos (per Leaf) Stainless Steel 150mm long handle complete all specified and directed by Engineer -in-charge.

Supply & Fixing Factory Made 30mm thick Solid WPC ( Wood polymer Composite ) Wiremesh Door Shutter of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension rade ), calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cum , having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter for fixing Mosquito mesh and XTN aluminium mesh together on panel area of door except stiles and rails to be panelled with and including mesh with self tapping round headed scresws at required distance, screws and edges covered with feathered pvc edge beading all around of mesh and fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws with and including 03 Nos door Stainless steel butt hings 100mm long with Stainlessd steel screws for each , 02 Nos stainless steel barrel tower bolts of extrude section, 150mm long (ISI marked), 2 Nos stainles steel handles, 125 mm long, (ISI marked) , 01 No. of helical door spring of 300 mm length complete all as specified and as directed by Engineer-in-charge. Note: 1. Material test certificate of all the items and authentication should be compulsory provided by the manufacturing company 2. The rate of 03 Nos door Stainless steel butt hings 100mm long with Stainlessd steel screws for each , 02 Nos stainless steel barrel tower bolts of extrude section, 150mm long (ISI marked), 2 Nos stainles steel handles, 125 mm long, (ISI marked) , 01no. of helical door spring of 300 mm length is inclusive in this item and nothing shall be paid extra on this item..3. The rate of Mosquito mesh and XTN aluminium mesh is included in this item and nothing shall be paid extra on this account.

Supply and fixing of factory made uPVC white colour Three track Slider Window including glass & mesh of area exceeding 1.00 Sqm and not exceeding 2.00 sqm each window made of extruded profiles of high impact modified grade manufactured from Tropicalized Blend with TiO2 and required additives, colorfast & being able to withsatand a weather resistance test of 16000 hrs on weathering apparatus, resistant to chemicals, and be fungal and vermin proof. The uPVC profile should be classed as self extinguishing to prevent support or enchancement of accidental fires. Extruded profile duly reiniforced with minimum 120 gsm zinc coated GI of 1.5mm to 2.5mm thickness to meet the wind load requirement on sash/mulilion and fitted in continuous length in closed chamber of required length (shape and size according to uPVC profile design). The internal drainage shall be isolated from chambers into which reinforcement can be placed or through which frame fixing passes. Drainage shall be either through the base or alternatively to the face, concealed by face drainage caps. uPVC systems must be fabricated with fusion welded corners and uPVC extruded glazing beads of appropriate dimensions with EPDM/TPE Gaskets. All hardware fitted must be of stainless steel, multipoint espag, plastic packers, plastic caps & necessary stainless steel screws, except handles to be of Zinc/Al alloy casted with powder coated, GI fasteners 100mm x 8mm size for fixing frame to wall. Outer frame of windows 118mm x 50mm , sash 45mm x 60mm consisting of multi chambered frame, sash 7 mullion/transom (wherever required), The sizes of the sections indicated are minimum and no additional cost shall be claimed for use of higher sections due to design considerations. The wall thickness of the profile shall be minimum 2.0 ± 0.2mm. The sheet glass shall be toughened of thickness 5mm. The wire mesh shall be of stainless steel stainless 0.36mm nominal dia of wire and average width of aperature 1.40 mm. After fixing the frame the gap between the frame and adjacent finished wall shall apply Silicon sealant to make joint, water proof of approved quality. There would be a conditional warranty of minimum 10 years on profile & 02 years on hardware from the date of completion. The uPVC system must be installed by profile manufacturer or their authorised agents only complete all as specified and as directed by Engineer-in- charge. (Note :- The rate of 5mm thick toughened glass for glazing and stainless steel wire mesh cloth 0.36mm nominal dia of wire and average width of aperature 1.40 mm is included in this item and nothing shall be paid extra on this account. Net opening will be measured for payment purpose.)

Supply and fixing for Providing and fixing of factory made uPVC white colour Louvered Casement Window / Ventilator of area not exceeding 1.00 Sqm each window made of extruded profiles of high impact modified grade manufactured from Tropicalized Blend with TiO2 and required additives, colorfast & being able to withsatand a weather resistance test of 16000 hrs on weathering apparatus, resistant to chemicals, and be fungal and vermin proof. The uPVC profile should be classed as self extinguishing to prevent support or enchancement of accidental fires. Extruded profile duly reiniforced with minimum 120 gsm zinc coated GI of 1.5m to 2.5mm thickness to meet the wind load requirement on sash/mulilion and fitted in continuous length in closed chamber of required length (shape and size according to uPVC profile design). The internal drainage shall be isolated from chambers into which reinforcement can be placed or through which frame fixing passes. Drainage shall be either through the base or alternatively to the face, concealed by face drainage caps. uPVC systems must be fabricated with fusion welded corners and uPVC extruded glazing beads of appropriate dimensions with EPDM/TPE Gaskets. All hardware fitted must be of stainless steel, multipoint espag, plastic packers, plastic caps & necessary stainless steel screws, except handles to be of Zinc/Al alloy casted with powder coated, GI fasteners 100mm x 8mm size for fixing frame to wall. Outer frame of windows 45mm x 50mm , with fixed frosted glass in the lower half, 4mm thk glass pinhead louvers in the upper half and Mesh consisting of multi chambered frame, sash & mullion/transom (wherever required), The sizes of the sections indicated are minimum and no additional cost shall be claimed for use of higher sections due to design considerations. The profile of the frame shall be suitable to install and fix mild steel guard bars. The wall thickness of theprofile shall be minimum 1.8 to 2.3 ± 0.2mm. The sheet glass shall be toughened of thickness 5mm. The wire mesh shall be of stainless steel stainless 0.36mm nominal dia of wire and average width of aperature 1.40 mm. After fixing the frame the gap between the frame and adjacent finished wall shall apply Silicon sealant to make joint, water proof of approved quality. There would be a conditional warranty of minimum 10 years on profile & 02 years on hardware from the date of completion. The uPVC system must be installed by profile manufacturer or their authorised agents only complete all as specified and as directed by Engineer-in- charge. (Note :- The rate of 5mm thick toughened glass for glazing, 4mm thick pinhead glass and stainless steel wire mesh cloth 0.36mm nominal dia of wire and average width of aperature 1.40 mm is included in this item and nothing shall be paid extra on this account. Net opening will be measured for payment purpose.)

Material and Labour for anti-skid premium (1st) quality coloured ceramic tiles 400mm x 400 mm and 7-8 mm thick,, in floors etc with and including 10 mm thick bedding layer using type-I adhesive (thick bed fixing) confirming to IS-15477:2004 and pointed in white or coloured epoxy grout to match the shade of tile including necessary cutting as per site requirement complete all as specified and as directed by Engineer-in-charge.

Material and Labour for providing and laying Premium (1st quality) straight edge,Stain free, glooss finish, Square marbonite Double charged vitrified tiles size in 600mm x 600mm x 9mm to 10mm thick as in floors etc. shade as approved by GE , set and jointed with using spacer and approved High polymer modified, grey cement-based tile adhesive suitable for fixing medium format tile/stone in walls/floor conforms to IS 15477 : 2019 type 2T “Adhesives for use with Ceramic, Mosaic and stone Tiles” Conforms to EN 12004: 2017 and is a normal cementitious adhesives (C1) with slip resistance (T) of class C1 and necessary grouting as per manufacturer’s instruction, completed all as specified and directed by engineer-in-charge.

Material and Labour for providing and laying Premium (1st quality) straight edge,Stain free, glooss finish, Square Double charge vitrified tiles size in 600mm x 600mm x 9mm to 10mm thick as in skirting surfaces shade as approved by GE , set and jointed with using spacer and approved High polymer modified, grey cement-based tile adhesive suitable for fixing medium format tile/stone in walls/floor conforms to IS 15477 : 2019 type 2T “Adhesives for use with Ceramic, Mosaic and stone Tiles” Conforms to EN 12004: 2017 and is a normal cementitious adhesives (C1) with slip resistance (T) of class C1 and necessary grouting as per manufacturer’s instruction, completed all as specified and directed by engineer-in-charge.

Material and Labour for glazed ceramic coloured tiles 7.5 mm to 8.5mm thick 450mm x 300mm size in verticle surface with and including 10mm thick backing coat using type-I adhesive (thick bed fixing) confirming to IS-15477:2004 and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement etc complete all as specified and as directed by Engineer-in-charge.

Supply and Fixing 16 mm bore CPVC pipe SDR 11 with and including CPVC SDR 11 fittings and fixed to walls & ceilings or laid in floors, complete complete all as specified and as directed by Engineer-in-charge

Supply and Fixing 20 mm bore CPVC pipe SDR 11 with and including CPVC SDR 11 fittings and fixed to walls & ceilings or laid in floors, complete complete all as specified and as directed by Engineer-in-charge

Supply and fixing 15mm bore Bib tap, long body, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 15mm bore Stop valves, fancy type, chromium plated with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge.

Supply and fixing 15mm bore Angular Stop Cock with wall flange, fency type chromium plated cast copper alloy screwed down, high pressure, screwed for iron pipe and fixed in position complete all as specified & directed by Engineer-in-charge.

Supply & Fixing 15 mm pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and and as directed by Engineer-in-charge.

Supply & Fixing Chromium plated shower rose 125mm size with swivel joint including fixing to steel pipe or union complete all as specified and as directed by Engineer-in-charge.

Suply & Fixing Health faucets steel Chromimum Plated with 1.00 mtr long steel Chromium Plated flexible pipe with and including hook fixed complete all as specifiedand as directed by Engineer-in-charge.

Material and Labour for Oval type vitreous china Wash Hand Basin, white, Size of 550mm x 460mm ,with and including 32mm chromium plated waste coupling and PVC bottle trap and fixing in marble slab complete all as specified and approved by GE / directed by Engr-in-Charge. Note: marble slab shall be measured and paid separately.

Supply & fixing PVC connections 15mm size with brass nuts of length 450mm complete all as specified and as directed by Engineer-in-charge.

Supply & fixing Rotational Moulded Polyethylene water storage tank ISI Marked of capacity 1000 litres (cylindrical vertical, with closed top), hoisted and fixed in position including making inlet and out let connection complete all as specified and as directed by Engineer-in-charge. (Note :- Ball valve and gate valve shall be measured & paid separately under appropriate items of Schedule 'A' BoQ.)

Supply and Fixing Ball valve high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe of size 20 mm bore (minimum weight 20mm-210 gram) complete all as specified and as directed by Engineer-in- charge.

Supply & fixing Gun metal, globe or gate valve (ISI marked), brass cast copper alloy, with iron wheel head, screwed both ends suitable for 20mm bore iron pipes complete all as specified and as directed by Engineer-in-charge.

Supply and fixing peg set / coat hooks (set of six hooks) made of stainless steel complete all as specified and as directed by Engineer-in- charge. .

Supply and fixing chromium plated brass towel rail, 20mm dia, D type, 60cm long fixed to wall complete all as specified and as directed by Engineer-in- charge.

Supply and Fixing 25mm dia Stainless steel curtain rod with bracket and knobs at both ends as per site requirement with accessories complete all as specified and directed by Engineer-in-charge.

Material and labour for PCC (1:4:8) type D-2 using 40 mm graded stone aggregates as in concrete bed for DWCPE pipes of 150 mm bore, laid to required slope including packing under and haunching against the sides of pipes after they are laid and tested including form work complete all as specified and as directed by Engineer-in-charge. Notes :- (i) Thickness of concrete bed below the barrel of pipe shall be 10 cm. (ii) Width of concrete bed shall be outer diameter of drain pipes (not of sockets / collar) plus 30cm. (iii) Excavation , earth work , returning filling shall be measured and paid seperately under appropriate items of schedule 'A' BoQ.

Supply , Fixing and testing for providing ,lowering , laying DWCPE (SN 8) pipe of 150mm internal bore as per IS-16098 of 2013, laid in trench and jointed with and including elastomeric sealing 'O' ring and fittings complete all as per manufacturer's instructions , complete all as speified and as directed by Engineer-in-charge. Note:- Excavation , earth work, returning filling , removal ,bedding and pedestal / anchorage if required shall be measured and paid separately under appropriate item of BOQ/ Sch 'A'

Material and Labour for Morrum / Red bajri filling in floors or pavings, laid in layers not .exceeding 15cm thick, spread,levelled and rammed including watering complete all as specified and directed by Engineer-in-Charge.

Material and labour for Plain Cement Concrete in flooring 25 mm thick levelling course PCC 1:2:4 type B-1 using 20mm graded aggregate finished even and rough to receive tiles complete all as specified and directed by Engineer-in-Charge.

Material and Labour for factory made,machine pressed precast interlocking paver block 60 mm thick with grey cement and pigment, any shape and size, conforming to IS 15658-2006, made out of M-35 grade concrete complete all as specified and as directed by Engineer-in- charge.

Material and Labour for factory made,machine pressed precast interlocking paver block 80 mm thick with grey cement and pigment, any shape and size, conforming to IS 15658-2006, made out of M-40 grade concrete cushioning complete all as specified and as directed by Engineer-in- charge.

Material and Labour for Treating the bottom and sides of excavation at the rate of 5 litre of chemical emulsion per sqm of surface area etc complete.

Material and Labour for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed by Engineer-in- charge.

Material and Labour for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed by Engineer-in- charge.

Material and labour for cement slurry @ 1.2 kg /sqm spreading with bristle brush with and including rendering 15 mm (average thickness) in cement mortar 1:3 finished even and fair mixing with Liquid water proof compound 200ml per 50 kg cement bag on roof surface complete all as specified and as directed by Engineer-in-Charge. Note:- Liquid water proofing comound shall be measured and paid seperately as supply only in appropriate item of schedule 'A' BoQ.

Material and Labour for Water proofing tratment to roof / terrace (material of water proof treatment as approved by GE) Single component, acrylic based, flexible, micro fibre reinforced waterproofing and heat reflective coating system. the treatment shall be carried out as per the manufacturers instructions and shall include the followings: (a) Preparation of substrate and cleaning it off all loose and triable by mechanical means (b) Open the cracks lines to form , V grooves with cutter/hammer/chisel up to 5-10mm and filling with crack filler and PU sealant. (c) application of primer coat @ 0.2 to 0.3 kg/ sqm followed by the first coat @ 0.75kg/ Sqm. (d) The second coat shall be applied @ 0.75 kg / Sqm and reinforced with fabric re-inforcement between the first and second coat. (e) The top coat of primer shall be applied after the second coat dries off @ 0.05-0.08 Kg per Sqm. (f) The material shall adhere to following specification. TECHNICAL SPECIFICATION OF MATERIAL Tensile Strength 1.5 MPa ASTM D412 Elongation at Break > 200% ASTM D412 Adhesion in Peel > 1.5 MPa (on concrete substrate) EN 1542 Crack Bridging Ability Passes upto 3.2mm Width ASTM C1305 Permeability to Water Vapour Passes IS 2645 Water Vapour Transimission ~ 23 g/m²/24hr ASTM E96 Water Absorption < 10% ( by Mass) ASTM D570 Microbiological Resistance No Algae & Fungal Growth ASTM D5590 Solar Reflectance Index 102 ASTM E1980. Note : Complete material shall be approved by GE and procured in bulk and kept in lock and key. Note : The installation company should be trained and authorized by Manufacturer & installation to be carried out as per manufacturers approved method statement. All auxiliary & accessories involved during application should be supplied by single manufacturer as a part of system. Any component used which is not manufactured by the particular manufacturer can only be used with official approval from manufacturer in consultation with GE.

Material and Labour for 40mm average thick PCC padding in 1:2:4 Type B-1 (using 20mm graded stone aggregates) as in roof slab finishing the surface even and fair using Liquid water proofing compound complete all as specified and directed. Liquid Water proofing compound shall be measured and paid separetly as supply only under appropriate item of Schedule 'A' BoQ.

Material and Labour for Making benching with PCC 1:2:4 type- B0, using 12.5mm graded stone aggregates using with Liquid Water Proof compound as per manufacturer's instruction along side wall adjoining to roof in concave shape complete all as specified and directed. Note : Liquid Water proofing compound shall be measured and paid separetly as supply only under appropriate item of Schedule 'A' BoQ.

Supply & Fixing Soap dish, vitreous China white, approximate size 160x160x90mm complete all as specified and as directed by Engineer-in-charge.

Supply & fixing 110 mm bore of pipe PVC (SWR) type B ring fit pipes single socket in any length with and including clamps as shown in BTD Drg No. 916 sheet 1/4 to 4/4 and BTD-917 sheet sheet 1/1 of stays to wall at a distance of 100-120mm away from walls complete all as specified and as directed by Engineer-in- charge

Supply & fixing 110 mm bore of pipe PVC (SWR) type B ring fit pipes single socket in any length with as shown in BTD Drg No. 916 sheet 1/4 to 4/4 and BTD-917 sheet sheet 1/1 laid in trenches complete all as specified and as directed by Engineer-in- charge

Supply & Fixing 110 mm bore of pipe PVC (SWR) Type B bends of any radius / shoe fixed to PVC pipes complete all as specified and as directed by Engineer-in-charge.

Supply & fixing 75 mm bore of pipe PVC (SWR) type B ring fit pipes single socket in any length with and including clamps as shown in BTD Drg No. 916 sheet 1/4 to 4/4 and BTD-917 sheet sheet 1/1 of stays to wall at a distance of 100-120mm away from walls complete all as specified and as directed by Engineer-in- charge

Supply & fixing 75 mm bore of pipe PVC (SWR) type B ring fit pipes single socket in any length with as shown in BTD Drg No. 916 sheet 1/4 to 4/4 and BTD-917 sheet sheet 1/1 laid in trenches complete all as specified and as directed by Engineer-in- charge

Supply & Fixing 75mm bore PVC (SWR) Type B bends any radius plain bends Tapers etc complete all as specified and as directed by Engineer-in-charge.

Material & Labour for 75 mm dia PVC (SWR) floor trap type B , plain with grating including jointing with solvent complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing PVC (SWR) gully trap 110 mm, setting and jointing with solvent cement type `P'/S complete all as specified and as directed by Engineer-in-charge.

Supply & Fixing PVC (SWR) gully trap 125 mm, setting and jointing with solvent cement type `P'/S complete all as specified and as directed by Engineer-in-charge..

Supply & Fixing PVC low level cistern of 10 ltrs capacity with top push buttion inclusive of brackets and PVC bend long type and connectin to flush pipe of any size and pattern with inlet ball valve float and handle complete all as specified and as directed by Engineer-in- charge

Supply & Fixing Vitreous china wash down water closed pan(pedestal Pattern) white , with and including plastic seat cover complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Cutting into existing manhole for connecting new drain pipe of 150 mm bore and making good the pipe and rendering disturbed surface where drain pipe have been inserted cutting out existing benching for forming branch channel (1/2 round or 3/4 round as required) in cement concrete 1:2:4 type B1 and finished the surface even and smooth and reforming benching as required and directed by Engineer - in - Charge.

Material and Labour for Plain Cement Concrete , type B1, 1:2:4 (20mm graded aggregate) as surface channels and drain.complete all as specified and as directed by Engineer-in-charge.

Material and Labour for PCC (1:2:4) type B1 using 20 mm graded aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, , water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Providing Precast Cement Concrete 1:2:4, Type B-1, using 20mm graded stone aggregates as in Kerb stone,Quion block, kneelers, apex stones, in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelveswith and including setting in cement mortar 1:4 , with plain fair faces, including chamfers, weatherings, throat- ing etc.complete with joints to match complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Cement Concrete Type C-1,1:3:6 ( 20mm graded stone aggregate) as in as in foundation filling and mass concrete , packing around interlocking paver blocks , for filling in bed block of hold fast etccomplete all as specified and as directed by Engineer-in-charge.

Material and labour for Damp proof course 40 mm thick cement concrete (1:1.5:3) type B-0, using graded stone aggregate mixed with water proofing compound as per manufacturer’s instructions , over with and including applying one coat of cold applied bituminous primer @ 0.70 litre per sq. m, over with and including blown bitumen grade 85/25 @ 1.20 kg/Sq. m surfaces including necessary formwork complete all as specified and as directed by Engineer-in-charge. Note : Ther rate of blown bitumen grade 85/25 @ 1.20 kg/Sq. m ,bituminous primer @ 0.70 litre per sq. m and form work is included in this item and nothing shall be paid extra on this account.

Suply & Fixing 75mm Hasp and staple, safety type, aluminium anodised , with mild steel hinge pin including bolt to hinge plate and fixed with screws with Size of hasp and staple75 mm complete all as specified and as directed by Engineer-in-charge.

Suply & Fixing Continuous (Piano) hinges, mild steel bright finished or electro galvanised, width of flaps ( when open) 40 mm. complete all as specified and as directed by Engineer-in-charge.

Suply & Fixing Ball catches with 8mm dia steel ball, and brass body and striking plate including in and fixed complete all as specified and as directed by Engineer-in-charge.

Suply & Fixing 18/20 mm prelaminated particle board, interior grade prelaminated one side with decorative choice lamination other side balancing white lamination as in cub board of complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa , conforming to IS-15961:2012 , as in cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge. Note:Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet shall be approved by GE in writing before incorporation in work.

Supply and fixing Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, conforming to IS-15961:2012 , as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge. Note:Pre- painted galvalume aluminum zinc coating GI based plain steel sheet shall be approved by GE in writing before incorporation in work.

Supply & Fixing Mild steel work as in tubular (round/square/ rectangular shape of pipes as approved by GE) as in trusses, purlins, rafter, MS plates,connecting plates, up to height 7.00mtr including post special shaped washers etc complete incl necessary nut bolts, wind ties and gusset plates etc using ERW or induction butt welded tubes conformining to IS 1161-1998 grade St-240 complete all as specified and directed by Engr-in-Charge.

Supply and fixing Mild steel work as in Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary,gusset plates, riveting, etc. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 all as specified and directed by Engr-in-Charge.

Supply & Fixing Mild steel Framed work Fe-290 (Gde E 165 ) as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete complete all as specified and as directed by Engineer-in-charge.Note:steel sheeting or other covering, running rails and guides shall be measured and paid seperately as supply and fix under appropriate item of schedule 'A' BoQ.

Supply & Fixing Mild steel work as in Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over with and including one coat of red oxide zinc chrome primer complete all as specified and as directed by Engineer-in-charge.

Material and Labour for preparation of new steel Surfaces and applying two coats of synthetic enamel paint over with and including one coat of red oxide zinc chrome primer of any description, not .exceeding 10cm in width or girth when unconnected with other painting or when painted in a different tint complete all as specified and as directed by Engineer-in-charge.

Material and Labour for preparation of new wooden Surfaces of any description, not otherwise descri-bed, over 10cm width or girth and applying two coats of synthetic enamel paint over with and including one coat of pink primer complete all as specified and as directed by Engineer-in-charge.

Supply & fixing factory made plain framed panelled shutters (two panels as approved), 35mm thick of 2nd class hard wood with lock rail and panel inserts of 12mm veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I), kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401, including 2nd class soft wood kail beading 20mm wide tapering from 10mm to 5mm on one side and also fitted to chowkhat complete all as specified and as directed by Engineer-in- charge. Note : - (i) The sutters shall be brought at site without primer and same shall be applying at site as per direction of Engineer-in-charge. Primer shall be measured paid separately under appropriate item (painting) of BOQ.

Supply and Fixing 35mm thick, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), using 2nd class hard wood (Bonsum/ Hollock) edges of frming plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc , sizes of members of shutters as specified in SSR Part-I, Section8, Clause 8.24 (a), supplied and fitted to chowkhats complete all as specified and as directed by Engineer-in-Charge. Note:- Wire gauze/ glass shall be measured and paid separately.Note : - (i) The sutters shall be brought at site without primer and same shall be applying at site as per direction of Engineer-in-charge. Primer shall be measured paid separately under appropriate item (painting) of BOQ.

Supply and fixing Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm all as specified and as directed by Engineer-in-charge.

Supply & fixing 300mm mild steel ordinary rat tail rod springs (helical spring) CONFORMING TO is 452-1973 , including roller & roller plate, fixed with screws/welding to steel frames/chowkats, complete all as specified and as directed by Engineer-in- charge.

Supply and fixing stainless steel barrel tower bolts, 200 mm long conforming to IS 15833-2009, with bright bolts and fixed complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 100mm long stainless steel butt hinges medium weight cold rolled complete all as specified & directed by Engineer-in-charge.

Supply & fixing 300mm long stainless steel sliding door bolts confoming to IS 15834-2008 , plate type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed length of bolt complete all as specified and as directed by Engineer-in- charge.

Supply and Fixing type 3 stainless steel door handle of size 150 mm conforming to IS 208-2020, fixed with countersunk conforming to IS 208-2020 complete all as specified and as directed by Engineer-in-charge.

Supply & fixing 4.0 mm thick, sheet glass ordinary quality fixing with oil putty to steel surfaces not exceeding 0.50 sqm in each pane complete all as specified and as directed by Engineer-in- charge.

Material and Labour for granite (any type) 20 mm thick work(table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, counter, shelves, urinal partition and like in cement mortar )1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed in CM 1:4 and moulding/rounding on edges by grinding complete all as specified and as directed by Engineer-in-charge.

Material and labour for Machine cut kota stone slab 20-25mm thick as in flooring, laid over with and including 20 mm thick cement screed base in Cement Mortar 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

Material and labour for Machine Cut kota stone slab 20-25 mm thick as in vertical surfaces such as skirting / Dado etc. laid over with and including 15 mm thick cement rendering in Cement Mortar 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Gl powder coated frame work size of grid 605 mm X 605 mm Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20mm and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. all as specified and directed by Engineer-in-Charge. Note: 1. The rate of Gypsum Board is not included in this item and shall be measured and paid seperately as Supply and fix under serial item no. 132.00 of Schedule 'A' BoQ. 2.The rate of Hangers 6 mm dia. Galvanised Steel wire Hanger I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long ( for Size of grid 605mm x 605mm ) is not included in this item and shall be measured and paid seperately as Supply and fix under serial item no. 133.00 of Schedule 'A' BoQ.

Material and labour for Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Hangers 6 mm dia. Galvanised Steel wire Hanger I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long ( for Size of grid 605mm x 605mm ) complete all as specified complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Continuous (Piano) hinges, mild steel bright finished or electro galvanised, width of flaps ( when open) 30 mm. complete all as specified and as directed by Engineer-in-charge.

Supply & Fixing Mild steel, plain, black sheet 1.25mm thick , in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and as directed by Engineer-in-charge.

Material & Labour for Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in soft / Loose soil complete all as specified and directed by Engineer-in- Charge. complete all as specified and directed by Engr-in-Charge.

Supply only chain link mild steel galvanised fencing (any size of mesh as approved by GE with 10 gauge wire) conforming to IS:2721:2003 complete all as specified and as directed by Engineer-in-charge. Note : 1.The weight of chain link fencing shall be ascertained by BOO as ordered by GE and payment shall be made accordingly. BOO duly counter signed by GE shall be enclosed with final bill. 2.Chain link mild steel galvanised fencing shall be approved by GE in writing before incorporation in work.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and as directed by Engineer-in-charge. Note: The rate for providing binding wire for fixing chain link fencing is incuded in this item and nothing shall be paid extra on this account.

Supply and fixing Mild steel work of Fe-290 Gde E -165 as in angle iron fencing posts & flat iron drilled and countersunk for boulders running bars,including embedding in concrete and scruing etc,post and struts in fencing including cutting, tops to shape as directed, bent to shape, drilling holes, notching for wire etc,flat iron fillets (for securing wire mesh etc.) Including all necessary drilling,bolting or riveting etc.complete all as specified and as directed by Engineer-in-charge. Note:- The element of Fixing of round bars for chain link fencing is included in this item .Nothing shall extra be paid on this account .

Supply only 10mm dia MS round bar for fixing of chain link fencing with post complete all as specified and as directed by Engineer-in-charge. Note :-Fixing element of this item is included in serial item no. 139.00 of BoQ here-in-before.

Supply and fixing Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings conforming to IS:278-2009 and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and as directed by Engineer-in-charge. (Each line wire to be measured) Note:Galvanised, 2 strand, steel barbed wire shall be approved by GE in writing before incorporation in work.

Supply and fixing 5-10 mm dia ,.exceeding 5cm but not exceeding 10cm long MS screw bolt machine made with hexagonal or square head at one end and screwed the other,or screwed both ends,each screwed end fixed with washer complete all as specified and as directed by Engineer-in-charge.

Supply and Fixing Mild steel work as in Bands, straps, supports or stays for rainwater, ventilating pipes,including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-410 or Fe-310.00 complete all as specified and as directed by Engineer-in-charge.

Material and Labour for Concealed point wiring for modular type fittings using approved colour coding as per IS (Red, Black and Green for single phase circuits), with two single core 2.5 Sqmm PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable 1100 volt grade ISI Marked, drawn through with and including new PVC rigid conduit 20mm dia ( heavy duty ) ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories) with all new fittings and all accessories i.e pipe bend pipe hook, elbow,junction box,with and including one single core 2.5 Sqmm PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable 1100 volt grade (ISI Marked) (as in green colour) as continuous earth continuity conductor including modular metal flush box concealed with front & modular cover plate with frame suitable matching colour of required module for mounting or housing modular switches 5Amp /6 Amp ,modular socket outlets 5Amp /6 Amp,modular fan regulators, modular two way switches 5Amp /6 Amp and modular bell push 5Amp /6 Amp for bell/ buzzer with and including blanking plates & all other fixing accessories for one light/ fan point controlled by one way 5/6 Amps modular switch complete all as specified and as directed by Engineer-in- charge Notes for serial item nos.144.00,145.00, 146.00 & 147.00 : (i)The quoted unit rate is deemed to be inclusive of cost of metal flush boxes, modular white cover plates, modular frame plates and flush fixed with cement mortar 1:4 etc.However modular switches 5Amp /6 Amp, modular socket out let5Amp /6 Amp , modular fan regulators modular two way switches 5Amp /6 Amp and modular bell push 5Amp /6 Amp for bell/ buzzer shall be measured and paid seperately under respective items of Schedule'A' BoQ. (ii) The rate of cutting chases (as required) is included in this item and nothing shall be paid extra on this account. (iii) On RCC roof / ceiling PVC conduit shall be provided on surface with proper fixing clips as directed by Engineer-in- Charge.The rate of this element is included in this item and nothing shall be paid extra on this account

All as per serial item No 144.00 of BoQ here-in-before but for modular socket outlet 5 pin 5/6 Amp on same board, complete all as specified and directed by Engineer-in-charge.

All as per serial item No 144.00 of BoQ here-in-before but for modular socket outlet 5 pin 5/6 Amp on independent board complete all as specified and directed by Engineer-in-charge.

All as per serial item No 144.00 of BoQ here-in-before but for bell/buzzer point, complete all as specified and directed by Engineer-in-charge.

Material and Labour for Concealed point wiring for modular type fittings using approved colour coding as per IS (Red, Black and Green for single phase circuits), with 4.0 Sqmm two single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable 1100 volt grade ISI Marked, drawn through with and including new PVC rigid conduit 25mm dia ( heavy duty ) ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories) with all new fittings and all accessories i.e pipe bend pipe hook, elbow,junction box,with and including one single core 4.0 Sqmm PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable 1100 volt grade (ISI Marked) (as in green colour) as continuous earth continuity conductor (green in colour) including modular metal flush box concealed with front & modular cover plate with frame suitable matching colour of required module for mounting or housing modular switches 15Amp/ 16 Amp and modular socket outlets 15Amp/16Amp, for modular socket out let point 15Amp/16Amp controlled by one way 15Amp/16 Amp modular switch with and including blanking plates & all other fixing accessories and including cutting chases (as required) and making good surfaces to match with adjoining surface complete all as specified and as directed by Engineer-in- charge Notes for serial item no.148.00 : (i)The quoted unit rate is deemed to be inclusive of cost of metal flush boxes, modular white cover plates, modular frame plates and flush fixed with cement mortar 1:4 etc.However modular switches 15Amp/16Amp and modular sockets 15Amp/16Amp shall be measured and paid seperately under respective items of Schedule'A' BoQ. (ii) The rate of cutting chases (as required) is included in this item and nothing shall be paid extra on this account. (iii) On RCC roof / ceiling PVC conduit shall be provided on surface with proper fixing clips as directed by Engineer-in- Charge.The rate of this element is included in this item and nothing shall be paid extra on this account

Supply and fixing Modular Switch one way , 6Amp ,1 module, 250 volts ,AC supply, ISI marked , complete all as specified and directed by Engineer-in-charge

Supply and fixing Modular Socket outlet , 6 Amp-2/3 pin combined 2 module , 250 volts ,AC supply, ISI marked complete all as specified and directed by Engineer-in-charge.

Supply and fixing Modular Switch one way 16 Amp,1 module 250 volts , AC supply , ISI marked complete all as specified and directed by Engineer-in-charge.

Supply and fixing Modular Socket outlet 6Amp/16Amp-2/3 pin combined,2 module ,250 volts ,AC supply, ISI marked complete all as specified and directed by Engineer-in-charge.

Supply and fixing modular Bell push, 01, Module, 6 Amp 250 Volts, AC supply,ISI marked complete all as specified and directed by Engineer-in-charge.

Supply and fixing Lamp holder ,ISI marked of PVC/Polycarbonate type with back plate suitable for batten fitting with and including 9Watt LED retrofit Lamp (base B-22) complete all as specified and directed by Engineer-in-charge.

Supply and fixing Electric / Electronic Bell, ding dong type 230 Volt AC supply,ISI marked complete all as specified and directed by Engineer-in-charge.

Supply and fixing Ceiling rose 3 terminal flush type 6 Amp 250V ,ISI marked ,AC supply, topline series with polycarbonate 20mm x 50 mm two to three terminal, complete all as specified and directed by Engineer-in-charge.

Supply and fixing sheet metal enclousers made out of CRCA mild steel sheet , IP-54 protection, flush mounted with metal door, powder coated DB SPN 8 way 230 V AC with 200 Amp rated copper bus bar, Double Door,08 modules, dust and vermin proof suitable for incorporation of MCBs / MCCBs/ Isolators etc.conforming to IS/IEC-61439-2:2011, BS-5484 complete all as specified and directed by Engineer-in-charge. Notes: (i)MCBs / MCCBs/ Isolators shall be measured and paid seperately under appropriate items. (ii) The rate of 200 Amps copper bus bar is included in this item and nothing shall be paid extra on this account.

Supply and fixing sheet metal enclousers made out of CRCA mild steel sheet , IP-54 protection, flush mounted with metal door, powder coated DB SPN 12 way 230 V AC with 200 Amp rated copper bus bar, Double Door,08 modules, dust and vermin proof suitable for incorporation of MCBs / MCCBs/ Isolators etc.conforming to IS/IEC-61439-2:2011, BS-5484 complete all as specified and directed by Engineer-in-charge. Notes: (i)MCBs / MCCBs/ Isolators shall be measured and paid seperately under appropriate items. (ii) The rate of 200 Amps copper bus bar is included in this item and nothing shall be paid extra on this account.

Supply and Fixing Sheet metal enclousers made out of CRCA mild steel sheet not less than 1.2mm thick,, IP-54 protection, flush mounted for metal door, powder coated DB VTPN 4 way , 415 V AC with and including 200 Amps rated copper bus bar, Double door, dust and vermin proof suitable for incorporation of MCCB / MCBs complete all as specified and as directed by Engineer-in- charge.Notes: (i)MCBs / MCCBs/ Isolators shall be measured and paid seperately under appropriate items. (ii) The rate of 200 Amps copper bus bar is included in this item and nothing shall be paid extra on this account.

Supply and fixing MCB SP 6 to 32 Amps, 230 volts , AC supply , rupturing capacity not less than 10KA,' C' Curve ,ISI Marked, complete all as specified and directed by Engineer-in-charge.

Supply and fixing MCB 32 Amp SPN ,240Volt , rupturing capacity 10 KA , CURVE ‘C’ ISI Marked, complete all as specified and directed by Engineer-in-charge.

Supply and fixing MCB 40 Amp to 63 Amp SPN ,240Volt , rupturing capacity 10 KA , CURVE ‘C’ ISI Marked, complete all as specified and directed by Engineer-in-charge.

Supply and Fixing MCCB 63 Amps 16 KA , 4 pole, 415 Volt fixed thermal and fixed maganatic setting complete all as specified and directed by Engr-in-Charge.

Material and Labour for Sub main wiring with two single core of size 6 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade,ISI Marked with and including non metallic rigid PVC conduit medium quality of size 25 mm dia conforming to 3537 Part-I ISI marked including all fitting such as Tee, Elbow, bend etc drawn in and including one single core of size 6 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ,ISI Marked as in contineous earth conductor cable connected to earth dolly complete all as specified and as directed by Engineer-in- charge. (Colour code phase-Red, Neutral-black and Earth as Green) complete all as specified and as directed by Engineer-in- charge. .Notes:-(a) Cost of PVC conduit , conduit accessories and earth wire included in sub main wiring. (b) Three single core 6 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade including non metallic rigid PVC conduit of size 25 mm dia shall be measured as one length.

Supply and fixing Square profile Batten , Decorative type wall mounted LED 20 Watt ( Warm / white light ) , 4.00 feet long , Pre wired , 6000K with built driver complete fitting and all other accessories fitting arrangements complete all as per manufacturer's instructions including electric connection connecting with using flexible copper wire twin core upto ceiling rose/connector complete all as specified and as directed by Engineer-in-Charge. Notes: (a) Contractor has to furnish a replacement warranty of 02 years for LED Light fittings complete including lamps from the certifiy date of completion of CA. The product will be replaced free of cost in the following case :- (i) Manufacturing defects. (ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (b) All LED light must meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13. (c) Scope of work shall include to fix LED Light fittings walls/ceiling which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account. (d) The rate of electric connection connecting with using flexible copper wire twin core upto ceiling rose/connector is included in this item and nothing shall be paid extra on this account.

Supply and fixing Mirror Light fitting 9/10 watt ,6000K, linear & compact with decorative grey end caps, polycarbonate body and ribbed opal diffuser complete with lamp and all other accessories fitting arrangements complete all as per manufacturer's instructions including electric connection connecting with using flexible copper wire twin core upto ceiling rose/connector complete all as specified and as directed by Engineer-in-Charge. Notes: (a) Contractor has to furnish a replacement warranty of 02 years for LED Light fittings complete including lamps from the certifiy date of completion of CA. The product will be replaced free of cost in the following case :- (i) Manufacturing defects. (ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (b) All LED light must meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13. (c) Scope of work shall include to fix LED Light fittings walls/ceiling which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account. (d) The rate of electric connection connecting with using flexible copper wire twin core upto ceiling rose/connector is included in this item and nothing shall be paid extra on this account.

Supply & Fixing Building Security LED Light of 35 watt , IP 66 , luminaire with high power with toughened glass complete as per manufacturer's instructions with and including bracket made out with 40mm bore Galvanised Iron Light grade pipe 1.20 mtr length bent to shape with 02 sets of MS clamps made out of minimum 3 mm MS flat iron with suitable bolt ,nuts and washers complete and fixing to wall / column with and including electrical connection with 1.5 mtr long twin core round copper conductor cable of suitable size and testing complete all as specified and directed by Engineer-in-charge. Notes: (a) The rate of bracket made out with 40mm bore Galvanised Iron Light grade pipe 1.20 mtr length bent to shape with 02 sets of MS clamps made out of minimum 3 mm MS flat iron with suitable bolt and nuts and electrical connection with 1.5 mtr long twin core round copper conductor cable of suitable size is included in this item and nothing shall be paid extra on this account. (b) Contractor has to furnish a replacement warranty of 02 years for Security LED Light fittings complete including lamps from the certifiy date of completion of CA. The product will be replaced free of cost in the following case :- (i) Manufacturing defects. (ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (c) All Security LED Light must meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13. (d) Scope of work shall include to fix Security LED Light fittings walls/building which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account.

Supply and Fixing LED Luminaire size 600mm x 600mm , 36Watt,220 Volt , AC , Recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders and LED Lamp suitable for roof ceiling , efficacy not less than 100 lumen/watt , extruded Aluminium/polycarbonate, PC diffusor and inbuilt driver complete as per manufacturer's instructions with and including connection with flexible twin core copper cable of size 23/.00076 from ceiling rose to fitting complete all as specified and as directed by Engineer-in- charge.

Material and Labour for earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6 mm thick burried directly in ground to depth of pit not less than 2.25 m below normal ground level with top edge of the plate not less than 1.5 m below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal / coal dust and common salt filling in alternate layers and connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of GI or steel including GI protection pipe 15mm dia light grade upto the extent of 7.5 metre and connecting to earthing test point, main switch board including GI pipe 20 mm dia light grade for watering, MS funnel and bringing out the watering pipe upto 30 cm above the normal ground level plugged at top including all fitting including PCC earth pit with PCC 1:2:4 type B-1 using 20mm graded stone aggregate and RCC pit cover including necessary earthwork and excavation in any type of soil complete all as specified as shown in electrical plate No 3 of SSR Part-I and testing on completion. Note:- (i) Earth continuity of GI wire 4 mm including protection pipe up to 7.5 mtrs from earth electrode will be included in unit rate, complete all as specified and directed. (ii) The rate of earth work in soft/loose soil i.e. excavation, returing filling and removal, form work is included in this item and nothing shall be paid extra on this account. (iii) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (iv) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge.

Supply and laying or fixing or laid in trenches/ ducts/ through pipes/ in floors / under roads/ hard standing /along poles and testing LT cable XLPE, PVC insulated screened, bedded, galvanised steel strip or wire armourd cable (heavy duty) 1100 volt grade with aluminium conductor having cross sectional area 70 Sqmm 3.5 core conforming to IS-7098 (Part-I -1988) complete all as specified and as directed by Engineer-in-Charge. (Excavation and earth work, sand cushioning & GI pipe shall be measured and paid for separately)

Material and Labour sand cushioning, with dry and clean fine river sand for underground cable 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cable complete all as specified. (Note:- Punned thickness shall be considered for payment purpose)

Supply and laying Best quality, locally available, sub class ‘B’ burnt clay bricks (Old Size) for cable protection, laid flat and dry in trenches over the cable , perpendicular to the direction of cable complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing Ceiling fan of 1200mm sweep complete with blades, down rods, with and including remote control and accessories, 230 Volts, single phase, 50 Hz, Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current (BLDC) motor connecting up complete with and including three core flexible PVC insulated multi stranded copper conductor cable of suitable size from ceiling rose / connector, including extra GI / MS pipe down rod, as per site requirement , with and including serial number of fan as issued by Engineer-in-charge and GE office name with red colour permaent marker complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Exhaust fan 300mm sweep (Heavy duty) steel body, BEE, 5 star rated ,AC Supply, single phase ,230 volts, 50HZ,900RPM with and including frame including new mosquito stainless steel wire mesh of guage 0.36mm with suitable wooden frame protection against birds etc. mounted in suitable opening arrangmement in wall and electric connection with and including three core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm drawn in flexible PVC Conduit and hanging on wall with 04 Nos. steel fastners 10mm dia 100mm long with and including serial number of fan as issued by Engineer-in-charge and GE office name with red colour permaent marker complete all as specified and directed by Engineer-in-charge.

Supply and Fixing water heater (Geyser) Auto restrat and safety measures type electrical operated 230/240 Volts 25 ltr capacity, BEE 5 star rated complete with all safety equipment and accessories such as safety valve, thermostat, plug top, etc. required for proper functionality & including electric/earth connections and carrying out grounting & complete installations with mounting bolts,nuts including testing after installation complete complete all as specified & directed by Engineer-in- Charge.

Supply and fixing Single Pole and Neutral enclosure with a two pin and earth plug and socket complete with and including one MCB single pole of capacity 25 Amps,'C' curve,10KA , 240 volts complete all as specified and directed by Engineer-in-Charge.Note: The rate of one MCB single pole of capacity 25 Amps,'C' curve, 10KA, 240 volts is included in this item and nothing shall be paid extra on this account.

Material and Labour for Making the hole under road and hard standing suitable for laying and inserting pipe up to 100mm dia pipe of any length by mechanical drill system or Auger system and making the surface good as per existing surface complete all as specified and all as directed by Engineer-in-charge. Note : The rate of pipe is not included in this item and Pipe of suitable size shall be measured and paid seprately under relevant item of Schedule 'A' BoQ.

Supply and fixing GI tubing, light grade 80 mm bore complete with all fittings for cable protection, fixed along poles or laid under floor , under road and hardstanding etc. complete with flat iron clamps of size 25mm x 4 mm , nuts, bolts and washers complete complete all as specified and as directed by Engr - in- Charge.

SHARDA ENTERPRIES (BID ID -3496233)

V K CONTRACTOR (BID ID -3502872)

Singla Enterprises (BID ID -3496343)

M/s MITTAL CONSTRUCTIONS (BID ID -3495133)

M/S VERMA BUILDERS & DEVELOPERS (BID ID -3496080)