Construction of Govt Degree Collage at Chowkiminar DisttUna HP SH Const of Building portion water supply and sanitary Installation rain water harvesting Tank Septic Tank and Site Development etc

Amount

Excavation in all kind of soil work by mechanical means (Hydraulic Excavator (3D) with driver and fuel)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) in all kind of soil, including dressing of sides and ramming of bottoms, upto any lift, including getting out the excavated soil and disposal of surplus excavated soils as directed, within any lead as per the direction by Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials. Any loss to the public / private property during the course of execution shall be the absolute responsibility of the contractor which shall have to be duly compensated by him in all cases The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Excavating trenches of required width for all kinds of soils pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, upto any depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm (twenty centimeter) in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within any lead The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (three point fifteen millimeter) thick welded with angle iron in frame 30×30×5mm (thirty into thirty into five millimeter) so as to give a fair finish including centring, shuttering, strutting and propping etcetera with wooden battens and ballies upto any height in all floor level of propping and centring below supporting floor to ceiling upto any height and removal of the same for in-situ reinforced cement concrete and plain concrete work as per HPPWD specifications in foundations, footings, bases of columns, etc. for mass concrete as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentals. The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (three point fifteen millimeter) thick welded with angle iron in frame 30×30×5mm (thirty into thirty into five millimeter) so as to give a fair finish including centring, shuttering, strutting and propping etcetera with wooden battens and ballies upto any height in all floor level of propping and centring below supporting floor to ceiling upto any height and removal of the same for in-situ reinforced cement concrete and plain concrete work as per HPPWD specifications in Columns, Pillars, Piers, Abutments, Posts and Struts as per the direction by the Engineer in charge upto any floor level including entire carriage of materials with in all leads and lifts and other incidentals. The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (three point fifteen millimeter) thick welded with angle iron in frame 30×30×5mm (thirty into thirty into five millimeter) so as to give a fair finish including centring, shuttering, strutting and propping etcetera with wooden battens and ballies upto any height in all floor level of propping and centring below supporting floor to ceiling upto any height and removal of the same for in-situ reinforced cement concrete and plain concrete work as per HPPWD specifications in Suspended floors, roofs, landings, balconies and access platformas per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (three point fifteen millimeter) thick welded with angle iron in frame 30×30×5mm (thirty into thirty into five millimeter) so as to give a fair finish including centring, shuttering, strutting and propping etcetera with wooden battens and ballies upto any height in all floor level of propping and centring below supporting floor to ceiling upto any height and removal of the same for in-situ reinforced cement concrete and plain concrete work as per HPPWD specifications in Lintels, beams, plinth beams, girders, bressumers and cantilevers as per the direction by the Engineer in charge upto any floor level including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (three point fifteen millimeter) thick welded with angle iron in frame 30×30×5mm (thirty into thirty into five millimeter) so as to give a fair finish including centring, shuttering, strutting and propping etcetera with wooden battens and ballies upto any height in all floor level of propping and centring below supporting floor to ceiling upto any height and removal of the same for in-situ reinforced cement concrete and plain concrete work as per HPPWD specifications in Stairs, (excluding landings) except spiral stair cases as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (three point fifteen millimeter) thick welded with angle iron in frame 30×30×5mm (thirty into thirty into five millimeter) so as to give a fair finish including centring, shuttering, strutting and propping etcetera with wooden battens and ballies upto any height of propping and centring below supporting floor to ceiling upto any height and removal of the same for in-situ reinforced cement concrete and plain concrete work as per HPPWD specifications in Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (three point fifteen millimeter) thick welded with angle iron in frame 30×30×5mm (thirty into thirty into five millimeter) so as to give a fair finish including centring, shuttering, strutting and propping etcetera with wooden battens and ballies upto any height of propping and centring below supporting floor to ceiling upto any height and removal of the same for in-situ reinforced cement concrete and plain concrete work as per HPPWD specifications in vertical and horizental fins individually or forming box louvers band, facias and eaves board as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (three point fifteen millimeter) thick welded with angle iron in frame 30×30×5mm (thirty into thirty into five millimeter) so as to give a fair finish including centring, shuttering, strutting and propping etcetera with wooden battens and ballies upto any height in all floor level of propping and centring below supporting floor to ceiling upto any height and removal of the same for in-situ reinforced cement concrete and plain concrete work as per HPPWD specifications in Edges of slabs and breaks in floors and walls under 20cm (twenty centimeter) wide as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (one cement : six coarse sand : twelve graded/crushed stone aggregate 20 mm (twenty millimeter) nominal size upto plinth level with cement mortar 1:6 (one cement : six coarse sand) as per the direction by the Engineer in charge including carriage of materials with in all leads and lifts and other incidentals. The rate including octroi, royality, Malkana, toll tax, sale tax or other taxes imposed by the Government.

Providing and laying in position cement concrete 1:5:10 (one cement : five fine sand : ten graded/ crushed stone aggregate 40 mm (forty millimeter) nominal size mechanically mixed and curing complete excluding the cost of centering and shuttering in foundation and plinth level as per the direction by the Engineer in charge including carriage of materials with in all leads and lifts and other incidentals. The rate including octroi, royality, Malkana, toll tax, sale tax or other taxes imposed by the Government.

Providing and laying cement concrete 1:5:10 (one cement : five coarse sand : ten graded/crushed stone aggregate 40 mm (forty millimeter) nominal size up to haunches of 100 mm (one hundred millimeter) diameter S.W. pipes including bed concrete as per standard design as per the direction by the Engineer in charge including carriage of materials with in all leads and lifts and other incidentals. The rate including octroi, royality, Malkana, toll tax, sale tax or other taxes imposed by the Government.

Providing and laying in position cement concrete 1:4:8(one cement: four coarse sand: eight graded/crushed stone aggregate 40mm (forty miillmeter) nominal size mechanically mixed and curing complete excluding cost of centering and shuttering in foundation and plinth level as per the direction by the Engineer in charge including carriage of materials with in all leads and lifts and other incidentals. The rate including octroi, royality, Malkana, toll tax, sale tax or other taxes imposed by the Government.

Providing and laying in position cement concrete 1:3:6 (one cement:three sand: six graded/crushed stone aggregate 40mm (forty millimeter) nominal size mechanically mixed and curing complete excluding cost of centring and shuttering in foundation and plinth level as per the direction by the Engineer in charge including carriage of materials with in all leads and lifts and other incidentals. The rate including octroi, royality, Malkana, toll tax, sale tax or other taxes imposed by the Government.

Providing and laying damp proof course 40mm (forty millimeter) thick with cement concrete 1:2:4 (one cement: two coarse sand: four graded crushed stone aggregate 12.5mm (twelve point five millimeter) nominal size and curing complete as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.70 kg (one point seventy kilogram) per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and laying in position specified grade of reinforcement cement concrete work M-25 (M-twenty five) design mix with minimum cement contents not less than 400 kgs.(four hundred kilogram) per cubic metre including curing complete excluding cost of form work in foundation footings bases of columns and the like mass concrete excluding the cost of centering, shuttering and finishing upto all height as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and laying in position specified grade of reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to all floor level, excluding the cost of centering, shuttering, finishing and reinforcement with M-25 (M-twenty five) design mix with minimum cement contents not less than 400 kgs.(four hundred kilogram) per cubic metre including curing complete excluding cost of form work upto all height as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and laying in position specified grade of reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to all floor level, excluding cost of centering, shuttering, finishing and reinforcement with M-25 (M-twenty five) design mix with minimum cement contents not less than 400 kgs.(four hundred kilogram) per cubic metre including curing complete excluding cost of form work upto all height as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing, hoisting and fixing above plinth level up to all floor level precast reinforced cement concrete in vertical and horizontal fins, individually or forming box louvers, setting in cement mortar 1:2 (one cement : two coarse sand), including the cost of required centering, shuttering but , excluding the cost of reinforcement with M-25 (M-twenty five) design mix with minimum cement contents not less than 400 kgs.(four hundred kilogram) per cubic metre including curing complete excluding cost of form work upto all height as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing, hoisting and fixing above plinth level up to all floor level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with M-25 (M-twenty five) design mix with minimum cement contents not less than 400 kgs.(four hundred kilogram) per cubic metre including curing complete excluding cost of form work upto all height as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and laying in position cement concrete M-20 design mix to obtain the minimum compressive strength of 20N/mm² with graded crushed stone aggregate 20mm (twenty millimeter) nominal size to give smooth and even surface and cement contents not less than at the rate of 340 kg (three hundred forty kilogram) per cubic meter mechanically mixed including curing complete excluding cost of form work in foundation and plinth level as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing 50mm (fifty millimeter) thick precast cement concrete Jali 1:2:4 (one cement : two coarse sand) : four graded/crushed stone aggregate 6mm (six millimeter) nominal size ), reinforced with 1.6 mm (one point six millimeter) dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (one cement: three fine sand) etc. complete, excluding plastering of the jambs, sills and soffits as per the direction by the Engineer-in-charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing Smooth finishing of the exposed surface of R.C.C. work with 6 mm (six millimeter) thick with cement mortor 1:3 (one cement : three sand) in any floor/height as per the direction by the Engineer-in-charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing steel reinforcement and Thermo-Mechanically Treated bars of grade Fe-500D or more approved make i.e. SAIL, RINL,Shyam Steel/TISCO, Jindal Panther (JSPL) for reinforced cement concrete work including bending cutting straightning and placing in position binding all complete upto any floor level/height as per the direction by the Engineer-in-charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth level up to all floor level in all shapes and sizes in cement mortor 1:6 (one cement: six coarse sand) as per the direction by the Engineer in charge including carriage of materials with in all leads and lifts and other incidentals. The rate including octroi, royality, Malkana, toll tax, sale tax or other taxes imposed by the Government.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all floor level in all shapes and sizes in cement mortor 1:6 (one cement: six coarse sand) as per the direction by the Engineer in charge including carriage of materials with in all leads and lifts and other incidentals. The rate including octroi, royality, Malkana, toll tax, sale tax or other taxes imposed by the Government.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth level in any floor/height in cement mortor 1:4 (one cement: four coarse sand) as per the direction by the Engineer-in-charge including entire carriage of materials with in all leads and lifts including other incidentals. The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure level in any floor/height in cement mortor 1:4 (one cement: four coarse sand) as per the direction by the Engineer-in-charge including entire carriage of materials with in all leads and lifts including other incidentals. The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and filling of hard stone under floor upto 22.5 cm (twenty two point five centimeter thick at site as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing cup board shutters 25 mm (twenty five millimeter) thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked, exterior grade (Grade l Type ll), having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm (twenty five millimeter) wide x12 mm (twelve millimeter) thick with necessary screws and bright finished stainless steel piano hinges, complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 18mm (eighteen millimeter) thick Pre-laminated flat pressed three layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately). as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 6 mm (six millimeter) commecial ply conforming to IS : 1328 BWR type of Action tesa, Black cobra, Green ply, Kit ply make plain linin with necessary screws, nuts, bolts and nails, including a coat of approved primer one one face and fixed on wooden/steel frame work complete (Frame work shall be paid for separately) as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 1.00mm (one point zero millimeter) thick decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 2nd (second class)class teak wood lipping/ moulded beading or taj beading of size 18x5 mm (eighteen into five millimeter) fixed with wooden adhesive of approved quality and screws/nails on the edges of the Pre-laminated particle board as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing steel frames for doors, windows and ventilators of mild steel channel/flats/angle iron sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing 40x5 mm (forty into five millimeter) flat iron hold fast 40 cm (forty centimeter) long including fixing to frame with 10 mm (ten millimeter) diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm (thirty into thirty into fifteen centimeter) 1:3:6 mix (one cement : three coarse sand : six graded/crushed stone aggregate 20mm nominal size) as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, shutters, frames with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment) fixing with carbon steel glavnized dash fastener of required dia and size (to be paid for separately) as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Extra for providing and fixing steel beading of size 10 x 10 x 1.6 mm (ten into ten into one point six millimeter) (box type), approved shape and section with screws instead of glazing clips and metal sash putty, in steel doors, windows, ventilators and composite units as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing float glass panes of nominal thickness 5 mm (five millimeter) (weight not less than 12.5kg/sqm) with putty and nails whereever necessary including racking out the old putty as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm (twenty five millimeter) to 40 mm (forty millimeter) thick fly proof stainless steel grade 304 wire gauge with 0.5 mm (zero point five millimeter) dia. wire and 1.4mm (one point four millimeter) wide aperture with matching wood beading as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 35 mm (thirty five millimeter) thick including ISI marked Stainless Steel butt hinges with necessary screws ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak three ply veneering with vertical grains or cross bands and face veneers on both faces of shutters as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing M.S. grills of required pattern in frames of fixed to steel windows by welding etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing powder coated aluminium sheet 2.5mm (two point five millimeter) thick (minimum thickness of powder coating 50 micron) machine moulded aluminium covering of approved pattern and design, made out of machine cut aluminium sheet and machine holed for receiving dash fastener, over expansion joints on vertical surfaces/ceiling floors, the fixing on plate in one row on one side of joint only shall be done with stainless steel dash fasteners of 8 mm (eight millimeter) dia and 75 mm (seventy five millimeter) long bolt including providing aluminium washers 2 mm (two millimeter) thick and 15 mm (fifteen millimeter) dia , at a staggered pitch of 200mm (two hundred millimeter) centre to centre including drilling holes in the receiving surface and providing expandable plastic sleeves in holes etc. complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 300x16mm(three hundred into sixteen millimeter ) aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etcetera complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 250x16mm(two hundred fifty into sixteen millimeter ) aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etcetera complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 200x10mm (two hundred into ten millimeter ) aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etcetera complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 150x10mm (one hundred fifty into ten millimeter ) aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etcetera complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 100x10mm (one hundred into ten millimeter ) aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etcetera complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 125mm (one hundred twenty five millimeter ) aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etcetera complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 100mm (one hundred millimeter ) aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etcetera complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 75mm (seventy five millimeter ) aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etcetera complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials. The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing chromium plated brass 50 mm (fifty millimeter) cupboard or wardrobe knobs with nuts complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 40mm (forty millimeter) special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 150mm bright finished brass hard drawn hooks and eyes as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

P/F curtain rods of 1.25mm (one point two five millimeter) thick chromium plated brass brackets with wooden plugs, etc. as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

25mm (twenty five millimeter) thick Kota stone slab flooring over 20 mm (twenty millimeter) (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (one cement : four coarse sand) as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Kota stone slabs 20 mm (twenty millimeter) thick in risers of steps, skirting, dado and pillars laid on 12 mm (twelve millimeter) (average) thick cement mortar 1:3 (one cement: three coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

25mm (twenty five millimeter) thick Kota stone slab flooring over 20 mm (twenty millimeter) (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (one cement : four coarse sand) and extra for Kota stone/ sand stone in treads of steps and risers using single length up to 1.05 (one point zero five) metre as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and laying Makrana white second quality marble stone flooring with 18mm (eighteen millimeters) thick marble stone as per sample of marble approved by Engineer-in-charge, over 20 mm (twenty millimeter)(average) thick base of in cement mortor 1:4 (one cement: four sand) laid and jointed with grey cement slurry, including rubbing and polishing complete upto all floor level as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and laying Udaipur green marble stone flooring with 18mm (eighteen millimeters) thick marble stone as per sample of marble approved by Engineer-in-charge, over 20 mm (twenty millimeter)(average) thick base of in cement mortor 1:4 (one cement: four sand) laid and jointed with grey cement slurry, including rubbing and polishing complete upto all floor level as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and laying Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm (eighteen millimeter) thick stone slab over 20 mm (twenty millimeter) (average) thick base of cement mortar 1:4 (one cement : four coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified upto all floor level as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab upto all floor level as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Extra for pre finished nosing to treads of steps of marble stone upto all floor level as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and laying full body matt finished/ double charged vitrified floor tiles in Size of tile 600x600 mm (six hundred into six hundred millimeter) (thickness to be specified by the manufacturer) of Kazaria, NITCO, SOMAMY, ORIENT, RAK make with water absorption less than 0.08% (zero point zero eight percent) and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm (twenty millimeterO thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm ( three point three kilogram per square meter) including grouting the joint with white cement and matching pigments etc. complete upto all floor level as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and laying full body matt finished/ double charged vitrified tile of size 300x300 x 9.8mm (three hundred into three hundred into nine point eight millimeter) of Kazaria, NITCO, SOMAMY, ORIENT, RAK make having with water absorption less than 0.5%(zero point five percent) and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc. laid on 20mm (twenty millimeter) thick base of cement mortar 1:4 (one cement : four coarse sand) in all shapes and patterns including grouting the joints with white cement mixed with matching pigments etc. complete upto all floor level as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and laying ten millimeter thick double charged Vitrified tiles in 600mm x 600mm (six hundred millimeter into six hundred millimeter) of Kazaria, NITCO, SOMAMY, ORIENT, RAK make, with water absorption less than 0.08 % (zero point zero eight percent) and conforming to I.S. 15622, of approved make, in all colours and shade, in skirting, riser of steps, over 12 mm (twelve millimeter) thick bed of cement mortar 1:3 (one cement: three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm ( three point three kilogram per square meter) including grouting the joint with white cement and matching pigments etc. complete upto six level as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (three hundred into three hundred millimeter) (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make Kazaria, Nitco, Somany, Orient Sell, RNK, Johanson & Johanson in all colours, shades except burgundy, bottle green, black, in skirting, risers of steps and dados over 12 mm (twelve millimeter) thick bed of cement mortar 1:3 (one Cement : threeCoarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc complete upto all floor level as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, goods service tax, labour cess or other taxes imposed by the Government.

Grouting the joints of flooring tiles of size 300x300 mm (three hundred into three hundred millimeter) make Kazaria, Nitco, Somany, Orient Sell, RNK, Johanson & Johanson having joints of 3 mm (three millimeter) width, using epoxy grout mix of 0.70 kg (zero point seven zero kilogram) of organic coated filler of desired shade (0.10 kg (zero point one zero kilogram) of hardener and 0.20 kg (zero point two zero kilogram) of resin per kg), including filling / grouting and finishing complete upto all floor level as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, goods service tax, labour cess or other taxes imposed by the Government.

Grouting the joints of flooring tiles of size 600x600 mm (six hundred into six hundred millimeter) make Kazaria, Nitco, Somany, Orient Sell, RNK, Johanson & Johanson having joints of 3 mm (three millimeter) width, using epoxy grout mix of 0.70 kg (zero point seven zero kilogram) of organic coated filler of desired shade (0.10 kg (zero point one zero kilogram) of hardener and 0.20 kg (zero point two zero kilogram) of resin per kg), including filling / grouting and finishing complete upto all floor level as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 10mm (ten millimeter) thick acid and or alkali resistant tiles of approved make and colour using acid and / or alkali resisting mortor bedding and joints filleed with acid /or alkali resistant cement as per IS: 4457 complete in flooring on a bed of 10 mm (ten millimeter) thick mortar 1:4 (one acid proof cement : four coarse sand) upto all floor level as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 10mm (ten millimeter) thick acid and or alkali resistant tiles of approved make and colour using acid and / or alkali resisting mortor bedding and joints filleed with acid /or alkali resistant cement as per IS: 4457 complete in dado/skirting on 12 mm (twelve millimeter) thick mortar 1:4 (one acid proof cement : four coarse sand) upto all floor level as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, goods service tax, labour cess or other taxes imposed by the Government.

Precast terrazo tiles 22mm (twenty two millimeter) thick with graded marble chips of size upto 12mm (twelve millimeter) laid in floors, and landings jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and polishing on 20mm (twenty millimeter) thick bed of cement mortar 1:4 (one cement: four coarse sand) light shade using white cement upto all floor level as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, goods service tax, labour cess or other taxes imposed by the Government.

Precast terrazo tiles 22mm (twenty two millimeter) thick with graded marble chips of size upto 12mm (twelve millimeter) laid in skirting and risers of steps not exceeding 30cm (thirty centimeter) height on 20mm (twenty millimeter) thick bed of cement mortar 1:3 (one cement: three coarse sand) light shade using white cement upto all floor level as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, goods service tax, labour cess or other taxes imposed by the Government.

40 mm(forty millimeter) thick with 20 mm (twenty millimeter) nominal size stone aggregate Cement concrete flooring 1:2:4 (one cement : two coarse sand : four graded/crushed stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etcetera complete upto all floor level as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, goods service tax, labour cess or other taxes imposed by the Government.

18mm (eighteen millimeter) thick Cement plaster skirting upto 30cm (thirty centimeter) height with cement mortar 1:3 (one cement: three coarse sand) finished with a floating coat of neat cement upto all floor level as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm (twenty millimeter into twenty millimeter into four millimeter) in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm (two point five kilogram per square meter) and grouting of the same. The rate is inclusive of all operation, material and required pattern upto all floor level as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, goods service tax, labour cess or other taxes imposed by the Government.

40mm (forty millimeter) thick rubbed stone flooring over 20mm (twenty millimeter) (average) thick base of cement mortar 1:5 (one cement : five coarse sand) with joints 3 mm (three millimeter) thick, side buttered with cement mortar 1:2 (one cement : two stone dust) admixed with pigment to match the shade of stone and pointing with same mortar upto all floor level as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and laying factory made chamfered edge Cement Concrete paver blocks of NTC make in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness and size/ shape, made by table vibratory method using PU mould, laid in required colour and pattern over 50mm (fifty millimeter) thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of 60 mm (sixty millimeter) thick C.C. paver block of M-35 (M thirty five) grade with approved color design and pattern as per required size and pattern, finishing and sweeping extra sand complete all upto any floor level/ height as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and laying factory made chamfered edge Cement Concrete paver blocks of NTC make in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness and size/ shape, made by table vibratory method using PU mould, laid in required colour and pattern over 50mm (fifty millimeter) thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of 80 mm (eighty millimeter) thick C.C. paver block of M-30 (M thirty) grade with approved color design and pattern as per required size and pattern, finishing and sweeping extra sand complete all upto any floor level/ height as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm (twenty into ten into two millimeter) and braced with flat iron diagonals 20x5 mm (twenty into five millimeter) size, with top and bottom rail of T-iron 40x40x6 mm (forlty into forty into six millimeter), with 40 mm (forlty millimeter) dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer upto any floor level/ height as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 75mm x 60mm (seventy five millimeter into sixty millimeter) moulded hand rails to straight length complete in second class Indian Teak wood as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing precoated galvanised iron profile sheets (Tata/Sail) (size, shape and pitch of corrugation as approved by Engineer in charge ) 0.60mm {(zero point six zero millimeter) (+0.05% (plus zero point zero five percent)}total coated thickness with zinc coating 120grams per sqm as per IS:277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-48 microns. Sheet should have protective guard fimlm of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 meter or as desired by Engineer in charge. The steel shall be fixed using self drilling/ self tapping screws of size {(5.5x55mm(five point five into fifty five millimeter)}with EPDM seal, complete upto any pitch in horizontal/vertical or curved surfaces, excluding the cost of purtins, rafters and trusses and including cutting to size and shape wheregver required as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing ridges plain (500-600mm) precoated galvanised steel (Tata/Sail) sheet roofing accessories 0.60mm {(zero point six zero millimeter) (+0.05% (plus zero point zero five percent)}total coated thickness with zinc coating 120grams per sqm as per IS:277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-48 microns using self drilling/self tapping screws complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing Crimp curve precoated galvanised steel (Tata/Sail) sheet roofing accessories 0.60mm {(zero point six zero millimeter) (+0.05% (plus zero point zero five percent)}total coated thickness with zinc coating 120grams per sqm as per IS:277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-48 microns using self drilling/self tapping screws complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing Flashings/Aprons (upto 600mm) {(six hundred millimeter)} precoated galvanised steel (Tata/Sail) sheet roofing accessories 0.60mm {(zero point six zero millimeter) (+0.05% (plus zero point zero five percent)}total coated thickness with zinc coating 120grams per sqm as per IS:277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-48 microns using self drilling/self tapping screws complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing Gutter (upto 600mm) {(six hundred millimeter)}overall girth precoated galvanised steel (Tata/Sail) sheet roofing accessories 0.60mm {(zero point six zero millimeter) (+0.05% (plus zero point zero five percent)}total coated thickness with zinc coating 120grams per sqm as per IS:277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-48 microns using self drilling/self tapping screws complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 110mm (one hundred ten millimeter) dia of D-plastor or victus make unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm (fifty into fifty into fifty millimeter) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (one cement : four coarse sand) and making good the wall etc. complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 110mm (one hundred ten millimeter) dia of D-plastor or victus make on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millimeter) gap for thermal expansion, as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 110mm (one hundred ten millimeter) dia plain bend of D-plastor or victus make on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millimeter) gap for thermal expansion as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 110mm (one hundred ten millimeter) dia plain shoe of D-plastor or victus make on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millimeter) gap for thermal expansion as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 110mm (one hundred ten millimeter) dia coupler of D-plastor or victus make on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millimeter) gap for thermal expansion as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in trusses and trussed purlins in building in position and applying a priming coat of approved steel primer all complete. as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Steel work welded in built up sections, framed work approved make i.e.TATA/JINDAL San HARVIC Steelman Industries P.D. Industries metal windows, Chandni Industires Ganpati Udyog (Rajpura) ,including cutting ,hoisting ,fixing in position and applying a priming coat of approved steel primer using structure steel etcetera as required lead paint in gratings framed guard bars, ladders, railling, brackets and similar works complete upto all heights/all floor level as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing M.S. tube hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 4mm (four millimeter) thick aluminum composite panel (ACP) in ceiling with butt joining and nails (frame work and cover fillets to bemeasured and paid for separately) .as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing Accustic Aerolite with 20 mm (twenty millimeter) thick beveled tegular mineral fibre false ceiling tile (NRC 0.7) at all heights of size 595x595mm (five hundred ninety five into five hundred ninety five millimeter) of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm (zero point three three millimeter) thick (galvanized @120 gms) comprising of main T runners of 15x32 mm (fifteen into thirty two millimeter) of length 3000 mm (three thousand millimeter), cross T of size 15x32mm (fifteen into thirty two millimeter) of length 1200 mm (one thousand two hundred millimeter) and secondary intermediate cross T of size 15x32 mm (fifteen into thirty two millimeter) of length 600 mm (six hundred millimeter) to form grid module of size 600x600 mm (six hundred into six hundred millimeter) suspended from ceiling using galvanised mild steel item (galvanised@80gsm) 50 mm (fifty millimeter) long 8mm oute diameter M-6 dash fasteners, 6 mm (six millimeter) diameter fully threaded hanger rod up to 1000 mm (one thousand millimeter) length and L shape level adjuster of size 85x25x2 mm (eighty five into twenty five into two millimeter), spaced at 1200 mm (one thousand two hundred millimeter) centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24x3000 mm (twenty four into twenty four into three hundred millimeter) made of 0.40 mm (zero point four zero millimeter) thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm (four hundred fifty millimeter) centre to centre and 40 mm (forty millimeter) long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm (zero point ninety liter per ten square meter) over an under coat of primer applied @ 0.80 ltr/ 10 sqm (zero point eighty liter per ten square meter) of approved brand and manufacture upto all heights as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Applying priming coat:with ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Painting wood work with Deluxe Multi Surface Paint of required shade two or more coat applied @ 0.90 ltr/10 sqm (zero point ninety liter per ten square meter) over an under coat of primer applied @0.75 ltr/10 sqm (zero point seven five liter per ten square meter) of approved brand and manufacture ICI (Dulex Glass) , Nerolac, Berger (Luxol High Glass), Asian Paint (Premium ApcoliteGlass) Shalimar make in all height/ in all floor level as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Polishing on new wood work with ready mixed wax polish of approved brand and manufacture as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

6mm (six millimeter) plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self curing mortar of approved make upto all floor level as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

15mm (fifteen millimeter) Cement plaster on the rough side of single or half brick wall of mix cement mortor 1:6 (one cement: six coarse sand) upto all floor level as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

20mm (twenty millimeter) Cement plaster on the fair side of single or half brick wall of mix cement mortor 1:6 (one cement: six coarse sand) upto all floor level as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Forming groove of uniform size 15 mm (fifteen millimeter) wide and 15 mm (fifteen millimeter) deep groove in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications upto all floor level as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

25 mm (twenty five millimeter) thick plain cement mortar raised band in cement mortar 1:4 (one cement : four fine sand).as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and applying white cement based putty of average thickness 1 mm (one millimeter), of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade new work (two or more coats) over and including water thinnable priming coat Berger (castle) Jenson & Nicholson Paints, Aqualac make with cement primer in all floor level/height as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications ICI, Nerolac, Berger, Asian Paint Shalimar make two or more coats applied on walls @ 1.25 ltr/10 sqm (one point twenty five liter per ten square meter) over and including one coat of Special primer applied @ 0.75 ltr /10 sqm (zero point seventy five per ten square meter) upto all floor level as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Finishing walls with 100% (Hundred percent) Premium acrylic emulsion paint having VOC less than 50 gm (fifty grams)/litre and UV resistance as per IS 15489:2004, Alkali and fungal resistance, dirt resistance exterior paint (ASIAN-APEX ULTIMA/NEROLAC- wheather Shield)of required shade (Company Depot Tinted) with silicon additives on new work (Two or more coats applied @ 1.43 litre/ 10 sqm. (at the rate one point four three liter per ten square meter) Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm (at the rate of zero point nine zero liter per ten square meter) as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Finishing walls with Acrylic Smooth exterior paint of required shade ICI, Nerolac, Berger, Asian Paint Shalimar make on new work (Two or more coat applied @ 1.67 ltr/10 sqm (at the rate of one point six seven liter per ten square meter) over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) (at the rate of two point two zero kilogram per ten square meter) upto all floor level as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing plinth protection 50mm (Fifty millimeter) thick with cement concrete 1:3:6 (one cement : three coarse sand (Zone-III) : six graded/ stone aggregate 20mm (twenty millimeter) nominal size over 75mm thick bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including necessary excomption, levelling, dressing and finishing the top smooth complete in all floor level/height as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of applying First layer of slurry of cement @ 4.4 kg/sqm (at the rate of four point four kilogram per square meter) mixed with water proofing cement compound confirming to IS 2645 in recommended proportions including rounding offjunction of vertical and horizontal surface Second course of 20mm (twenty millimeter) cement plaster 1:3 (one cement: three coarse sand) mixed with water proofing compund in recommended porportion including rounding off junction of vertical and horizontal surface. Third course of applying blown or residual bitumen applied hot @1.7 Kg. per sqm (at the rate of one point seven kilogram per square meter) of area. Fourth course of 400 micron thick PVC sheet ( overlaps at joints of PVC sheet should be 100mm (one hundred millimeter) wide and pasted to each other with bitumen @ 1.7 kg/ sqm) as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing, laying 23cm (twenty three centimeter) dia half round (to level or slops) and joining with stiff mixture of cement mortor in the proportion of 1:1 (one cement: one sand) slt glazed stone ware pipes grade"A"of lthe internal diametres including testing of pipes and joints complete as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 4.0 mm (four point zero millimeter) thick glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing Aluminium fluted strips 3.15 mm (three point one five millimeter) thick sheet covering over expansion joints with iron screws as per design as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 12mm (twelve millimeter) thick green chalk board having size 3.00 x 1.50 mtr.(Non magentic) with superior quality framing specially anodized aluminum profile 20mm x 15mm (twenty millimeter into fifteen millimeter)with corners of black plastic shall be provided. The board surface shall be non porus ceramic particals on the top green surface for smooth writing with chalk over 11mm (eleven millimeter) thick partical board which shall have backing material of glavnized sheet 0.28mm (zero point two eight millimeter) thick approx the board shall be fixed on the wall with specially designed "J"clamp and square clamps with the help of nylon sleevs and screws as per the requirement upto any floor level/ height as per the direction by the Engineer-in-charge including entire carriage of materials with in all leads and lifts including other incidentals. The rates are inclusive octroi, royality, Malkana, toll tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing White Vitreous china Orissa pattern W.C. pan of size 580x440 mm (five hundred eighty into four hundred forty millimeter) with integral type foot rests water closet squatting pan (Indian type W.C. pan ) with 100 mm (one hundred millimeter) sand cast Iron P or S trap, 10 (ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing white vitreous china pedestal type water closet (European type) of preferred make of Cera/Hindware with seat and lid, 10 (ten) litre low level white vitreous china flushing cistern and C.P. flush bend with fittings & C.I. brackets, 40 mm (forty millimeter) flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand of preferred make of Cera/Hindware , shape, size and pattern including integrated white vitreous china cistern of capacity 10 (ten) litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing white vitreous china flat back half stall urinal of preferred make CERA/Hindware of size 580x380x350 mm (five hundred eighty into three hundred eighty into three hundred fifty millimeter) with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required Single half stall urinal with 5 (five) litre P.V.C. automatic flushing cistern as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing white vitreous china flat back half stall urinal of preferred make CERA/Hindware of size 580x380x350 mm (five hundred eighty into three hundred eighty into three hundred fifty millimeter) with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required Single half stall urinal with 10 (ten) litre P.V.C. automatic flushing cistern as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing wash basin with C.I. brackets, 15 mm (fifteen millimeter) dia CP Brass pillar taps 32mm (thirty two millimeter) C.P. brass waste of standard pattern of approved quality of preferred make of CERA/Hindware, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China Wash basin size 550x400 mm (five hundred fifty into four hundred millimeter) with a 15 mm (fifteen millimeter) CP Brass single hole basin mixer as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 600x450x200 mm (six hundred into four hundred fifty into two hundred millimeter) white vitreous china laboratory sink make of CERA/Hindware with C.I. brackets, C.P. brass chain with rubber plug, 40 mm (forty millimeter) C.P brass waste and 40mm (forty millimeter) C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required of approved quality and colouras per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing White Vitreous China Surgeon type wash basin CERA/Hindware make of size 660x460 mm (six hundred sixty into four hundred sixty millimeter) with a pair of 15 mm (fifteen millimeter) C.P. brass pillar taps with elbow including operated levers as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials. The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 32mm (thirty two millimeter) dia flexible P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 600x450 mm (six hundred into four hundred fifty millimeter) beveled edge mirror of superior glass (of approved quality) complete with 6 mm (six millimeter) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete Hindware or cera make as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing PTMT towel rail complete of preferred with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 600 mm (six hundred millimeter) long towel rail with total length of 645 mm (six hundred forty five millimeter), width 78 mm (seventy eight millimeter) and effective height of 88 mm, weighing not less than 190 gms (one hundred ninety grams) as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 600x120x5 mm (six hundred into one hundred twenty into five millimeter) glass shelf of preferred with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing PTMT soap Dish Holder of preferred having length of 138mm(one hundred thirty eight millimeter), breadth 102mm (one hundred two millimeter), height of 75mm (seventy five millimeter) with concealed fitting arrangements, weighing not less than 106 gms (one hundred six grams) size as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 15mm (fifteen millimeter) nominal bore C.P. brass bib cock of preferred make of Jal, Jaquar/Prayag/Hindware conforming to IS:8931 as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 15mm (fifteen millimeter) nominal bore C.P. brass long nose bib cock of preferred make Jal, Cera, Jaquar, Hindware, Prayag conforming to IS standards and weighing not less than 810 gms (eight hundred ten grams) as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 15mm (fifteen millimeter) nominal bore C.P. brass stop cock (concealed) of standard design and of preferred conforming to IS:8931 as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 15mm (fifteen millimeter) nominal bore uplasticised PVC connection pipe with brass unions of preferred as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 15mm (fifteen millimeter) nominal ball valve (brass) of preferred , High or low pressure, with plastic floats complete as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 20mm (twenty millimeter) nominal ball valve (brass) of preferred , High or low pressure, with plastic floats complete as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 15 mm (fifteen millimeter) nominal bore brass ferrule with C.I. mouth cover including boring and tapping the main TATA/Jindal make as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Making connection of G.I. distribution branch with G.I. main of 25 to 40 mm ((twenty five to forty millimeter) nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 15 mm (fifteen millimeter) dia nominal bore G.I. Pipes complete with G.I. fittings and clamps, including making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 20 mm (twenty millimeter) dia nominal bore G.I. Pipes complete with G.I. fittings and clamps, including making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL- PE Composite Pressure 1216 (16 mm OD) pipe conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot and cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers and connectors etc., with clamps at 1.00 (one point zero zero) metre ( spacing. This includes the costs of cutting chases and including testing of joints complete as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL- PE Composite Pressure 1620 (20 mm OD) pipe conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot and cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers and connectors etc., with clamps at 1.00 (one point zero zero) metre ( spacing. This includes the costs of cutting chases and including testing of joints complete as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 25mm (twenty five millimeter) nominal ball valve (brass) of preferred make CERA/Hindware, High or low pressure, with plastic floats complete as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one and half coarse sand (zone- III) : three graded/crushed stone aggregate 20 mm (twenty millimeter) nominal size, foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded/crhsed stone aggregate 40 mm (forty millimeter) nominal size), inside plastering 12 mm(twelve millimeter) thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded/crushed stone aggregate 20 mm (twenty millimeter) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80 cm (ninety into eighty centimeter) and 45 cm (forty five centimeter) deep including C.I. cover with frame (light duty) 455x610 mm (four hundred fifty five into six hundred ten millimeter) internal dimensions, total weight of cover and frame to be not less than 38 kg (thirty eight Kilogram) (weight of cover 23 kg (twenty three Kilogram) and weight of frame 15 kg (fifteen Kilogram) with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one and half coarse sand (zone- III) : three graded/crushed stone aggregate 20 mm (twenty millimeter) nominal size, foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded/crhsed stone aggregate 40 mm (forty millimeter) nominal size), inside plastering 12 mm(twelve millimeter) thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded/crushed stone aggregate 20 mm (twenty millimeter) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 120x90 cm (one hundred twenty into nighty centimeter) and 90 cm (ninety centimeter) deep including C.I. cover with frame (medium duty) 500 mm (five hundred millimeter) diameter, total weight of cover and frame to be not less than 116 kg (one hundred sixteen Kilogram) (weight of cover 58 kg (fifty eight Kilogram) and weight of frame 58 kg (fifty eight Kilogram) with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing C P. brass toilet paper holder of JAL, Cera, Jaquar, ESS make as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 75mm (seventy five millimeter) dia soil, waste and vent pipes Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 100mm (one hundred millimeter) dia soil, waste and vent pipes Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank Sintex make tripple layer 1000 or 2000 liter capacity including all fittings as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 100mm (one hundred millimeter) dia plain bend of required degree sand cast iron S&S as per IS - 1729 as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 75mm (seventy five millimeter) dia plain bend of required degree sand cast iron S&S as per IS - 1729 as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Supplying CI cover without frame for manholes for frame of internal dimension 455x610mm (four hundred fifty five into six hundred ten millimeter) rectangular C.I cover (Light duty) single seat pattern-1, the weight of cover to be not less than 23 kg (twenty three Kilogram) as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm (twenty into twenty into ten centimeter) cement concrete blocks 1:3:6 (one cement : three coarse sand : six graded/crushed stone aggregate 20 mm (twenty millimeter)nominal size as per standard design with 20x20 mm (twenty into twenty millimeter) square bar as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 15mm (fifteen millimeter) nominal dia CP Brass Single lever telephonic wall mixer of quality and make JAL,Jaquar, ESS as approved as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 510x1040 mm (five hundred ten into one thousand forty millimeter) bowl depth 250, No.1022-XD of PRAYAG polymers Stainless Steel A ISI 304 (18/8) kitchen sink of preferred with drain board as per IS:13983 with C.I. brackets and stainless steel plug 40 mm,(forty millimeter) including painting of fittings and brackets, cutting and making good the walls wherever required as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 610x510 mm (six hundred ten into five hundred ten millimeter) bowl depth 200, No.1022-XD of PRAYAG polymers Stainless Steel A ISI 304 (18/8) kitchen sink of preferred with drain board as per IS:13983 with C.I. brackets and stainless steel plug 40 mm,(forty millimeter) including painting of fittings and brackets, cutting and making good the walls wherever required as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 8 mm (eight millimeter) dia C.P. / S.S. Jet with flexible tube upto 1(one) metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 100 mm (one hundred millimeter) inlet and 75 mm (seventy five millimeter) outlet as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm (three hundred into three hundred millimeter)size (inside) the weight of cover to be not less than 4.50 kg (four point fifty kilogram) and frame to be not less than 2.70 kg (two point seventy kilogram) as per standard design with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 100mm (one hundred millimeter) mominsl size Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 bend of required degree with access door, insertion rubber washer 3 mm (three millimeter) thick, bolts and nuts complete. as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 75mm (seventy five millimeter) mominsl size Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 bend of required degree with access door, insertion rubber washer 3 mm (three millimeter) thick, bolts and nuts complete. as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 100x100x100 mm (one hundred into one hundred into one hundred millimeter) Sand cast iron S&S as per IS- 3989 single equal plain junction of required degree with access door, insertion rubber washer 3 mm (three millimeter) thick, bolts and nuts complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 75x75x75 mm (seventy five into seventy five into seventy five millimeter) Sand cast iron S&S as per IS- 3989 single equal plain junction of required degree with access door, insertion rubber washer 3 mm (three millimeter) thick, bolts and nuts complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 100mm (one hundred millimeter) dia Sand cast iron S&S as per IS - 3989 collar as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government. :

Providing and fixing 75mm (seventy five millimeter) dia Sand cast iron S&S as per IS - 3989 collar as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 100x100x100 mm (one hundred into one hundred into one hundred millimeter) sand cast iron S&S as per IS- 3989 double equal junction of required degree with access door, insertion rubber washer 3 mm (three millimeter) thick, bolts and nuts complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 75x75x75 mm (seventy five into seventy five into seventy five millimeter) sand cast iron S&S as per IS- 3989 double equal junction of required degree with access door, insertion rubber washer 3 mm (three millimeter) thick, bolts and nuts complete as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 100x100x100 mm (one hundred into one hundred into one hundred millimeter) sand cast iron S&S as per IS- 3989 double equal plain junction of required degree as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 75x75x75 mm (seventy five into seventy five into seventy five millimeter) sand cast iron S&S as per IS- 3989 double equal plain junction of required degree as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 100x100x100 mm (one hundred into one hundred into one hundred millimeter) sand cast iron S&S as per IS- 3989 single equal plain junction of required degree as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 75x75x75 mm (seventy five into seventy five into seventy five millimeter) sand cast iron S&S as per IS- 3989 single equal plain junction of required degree as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 100 mm (one hundred millimeter) nominal size sand cast iron S&S off Sets as per IS- 3989 as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 75 mm (seventy five millimeter) nominal size sand cast iron S&S off Sets as per IS- 3989 as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 100 mm (one hundred millimeter) nominal size M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 75 mm (seventy five millimeter) nominal size M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 100 mm (one hundred millimeter) nominal size lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 75 mm (seventy five millimeter) nominal size lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter as per the direction by the Engineer in charge and including entire carriage of materials within all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

Providing and fixing 3.00 HP Tullu Pump crompton make including board and fittings complete as per the direction by the Engineer in charge including entire carriage of materials with in all leads and lifts and other incidentials . The rates are inclusive octroi, royality, Malkana, toll tax, sale tax, goods service tax, labour cess or other taxes imposed by the Government.

K.K. Construction

m/s kathuria constrution co.

Om Parkash Sharma And Sons

Deepak Kumar Beetan

M/s Satish Kumar Sharma

ganesh

, D.S.Rathore

HANS CONSTRUCTIONS